The URL can be used to link to this page

Home My WebLink About3113 Teller StreetFrom: no-reolv(alci.wheatridae.m. us To: CommDev Pets Subject: Online Form Submittal: Sewer or Water Line Repair Permit Application Date: Monday, November 8, 2021 1:21:21 PM Sewer or Water Line Repair Permit Application This application is exclusively for SEWER OR WATER LINE REPAIR - IN YARD Your Permit will be emailed to the email address provided below once it is processed. THIS APPLICATION DOES NOT CONSTITUTE A PERMIT. DO NOT BEGIN WORK UNTIL PERMIT HAS BEEN ISSUED. Right of Way permits must be applied for with the Public Works Department. Is this application for Yes sewer line or water line repair - in yard only? PROPERTY INFORMATION Is this Residential or Residential Commercial? Property Address 3113 Teller St Property Owner Name Justin Willey Property Owner Phone Number (enter WITH dashes, eg 303-123- 4567) Ki�x3s�:�Q�:3r1� Property Owner Email lwiley3408@gmail.com Address Attach City of Wheat Ridge Electronic Payment Form - "DO NOT ATTACH A PICTURE OF A CREDIT CARD" CONTRACTOR INFORMATION Contractor Business Name Contractor's License Number (This is a 5 or Done Service Group INC has been issued and posted on the property. I certify that I have Yes been authorized by the legal owner of the property to submit this application and to perform the work described above. I attest that everything Yes stated in this application is true and correct and that falsifying information in this application is an act of fraud and may be punishable by fine, imprisonment, or both. Person Applying for April Yakish Permit Email not displaying correctly? View it in your browser. 6 digit number for the City of Wheat Ridge) Contractor Phone 303-343-0032 Number (enter WITH dashes, eg 303-123- 4567) Contractor Email permits@itsdone.com Address Retype Contractor permits@itsdone.com Email Address DESCRIPTION OF WORK Is this a sewer line or Sewer Line water line repair? Length of repair approx 40 feet Location of repair Interior- Kitchen/laundry in basement under slab & 1 toilet (backyard, frontyard, etc) Provide additional We are replacing 40 feet of 2 inch cast iron with 3 inch ABS pipe details Including then we will connect the two 2 inch lines from the bathtub and the Installation of clean- lavatory. We will run 3 inch ABS to the toilet sweep and rehook Outs. up to the 4 inch cast iron stack. Project Value (contract 3362.00 value or cost of ALL materials and labor) SIGNATURE OF UNDERSTANDING AND AGREEMENT I assume full Yes responsibility for compliance with applicable City of Wheat Ridge codes and ordinances for work under any permit issued based on this application. I understand that work Yes may not begin on this property until a permit From: no-reolv(alci.wheatridae.m. us To: CommDev Pets Subject: Online Form Submittal: Sewer or Water Line Repair Permit Application Date: Friday, November 5, 2021 11:49:45 AM Sewer or Water Line Repair Permit Application This application is exclusively for SEWER OR WATER LINE REPAIR - IN YARD Your Permit will be emailed to the email address provided below once it is processed. THIS APPLICATION DOES NOT CONSTITUTE A PERMIT. DO NOT BEGIN WORK UNTIL PERMIT HAS BEEN ISSUED. Right of Way permits must be applied for with the Public Works Department. Is this application for Yes sewer line or water line repair - in yard only? PROPERTY INFORMATION Is this Residential or Residential Commercial? Property Address Property Owner Name Property Owner Phone Number (enter WITH dashes, eg 303-123- 4567) Property Owner Email Address Attach City of Wheat Ridge Electronic Payment Form - "DO NOT ATTACH A PICTURE OF A CREDIT CARD" 3113 Teller St Wheat Ridge Justin Willey 303-667-6890 n/a WRP 11-5-2021 Ddf CONTRACTOR INFORMATION Contractor Business The Elite Pipe MD Name Contractor's License 120161 Number (This is a 5 or has been issued and posted on the property. I certify that I have Yes been authorized by the legal owner of the property to submit this application and to perform the work described above. I attest that everything Yes stated in this application is true and correct and that falsifying information in this application is an act of fraud and may be punishable by fine, imprisonment, or both. Person Applying for David salvidrez Permit Email not displaying correctly? View it in your browser. 6 digit number for the City of Wheat Ridge) Contractor Phone 720-662-4381 Number (enter WITH dashes, eg 303-123- 4567) Contractor Email david@elitepipemd.com Address Retype Contractor david@elitepipemd.com Email Address DESCRIPTION OF WORK Is this a sewer line or sewer Line water line repair? Length of repair 10' Location of repair In front yard. (backyard, frontyard, etc) Provide additional Install dual sweep clean outs 8' deep details including installation of clean- o uts. Project Value (contract 2600 value or cost of ALL materials and labor) SIGNATURE OF UNDERSTANDING AND AGREEMENT I assume full Yes responsibility for compliance with applicable City of Wheat Ridge codes and ordinances for work under any permit issued based on this application. I understand that work Yes may not begin on this property until a permit A i CITY OF WHEAT RIDGE Building Inspection Division (303) 235-2855 Office INSPECTION NOTICE Inspection Type: Job Address: f iCz_ tom. Permit Number: `,. ❑ No one available for inspection: Tim %My/ M Re -Inspection required: Yes; o When corrections have been made, schedule for re -inspection online at: http://www.ci.wheatridge.co.uslinspecon Date: / spec` 1* ► � i City of Wheat Ridge '/� Residential Solar PERMIT - 202002023 PERMIT NO: 202002023 ISSUED: 10/12/2020 JOB ADDRESS: 3113 Teller St EXPIRES: 10/12/2021 JOB DESCRIPTION: Install roof mount, flush mount, grid -tied 13.545 kw solar PV system, 43 panels on roof, no structural required *** CONTACTS *** OWNER (720)296-0724 TENDER CARE ASSISTED LIVING LL SUB (303)577-9628 THOMAS B., CHRISTOPHER L ANDY 070159 SUNRUN INSTALLATION SRVS. INC. *** PARCEL INFO *** ZONE CODE: UA / Unassigned USE: UA / Unassigned SUBDIVISION CODE: 161 / BLOCK/LOT#: 0 / *** FEE SUMMARY *** ESTIMATED PROJECT VALUATION: 25,735.00 FEES Total Valuation 0.00 Residential Solar 500.00 ** TOTAL ** 500.00 *** COMMENTS *** *** CONDITIONS *** A printed copy of the permit and city stamped on-site plans must be available on-site for the first inspection. Approved per plans and red -line notes on plans. Must comply with 2018 IRC, 2020 NEC and all applicable City of Wheat Ridge Municipal Codes. Work is subject to field inspections. I, by my signature, do hereby attest that the work to, be performed shall comply with all accompanying approved plans and specifications, applicae building codes, and all applicable municpal codes, policies and procedures, and that I am the legal owner or have been authorized by the legal owner of the property and am authorized to obtain this permit and perform the work described and approved in conjunction with this�permrt. I further attest that I am leg ally authorized to include alI entities named within this document as parties to the work to be performed and that all work to be performed is disclosed in this document and/or its' accompanying approved plans and specifications. Signature of OWNER or CONTRACTOR (Circle one) Date 1, This permit was issued based on the information provided in the permit application and accompanying plans and specifications and is subject to the compliance with those documents, and all applicable statutes, ordinances, regulations, policies and procedures. 2. This permit shall expire 365 days after the date of issuance regardless of activity. Requests for extension must be made in writing and received prior to the date of expiration. An extension of no more than 180, days made be granted at the discretion of the Chief Building Official and may be subject to a fee equal to one-half of the original permit fee. 3. If this permit expires, a new permit may be required to be obtained. Issuance of a new permit shall be subject to the standard requirements, fees and��procedures for approval of any new permit. Re -issuance or extension of expired permits is at the sole discretion of the Chief Building Official and is not guaranteed. 4. No work of any manner shall be performed that shall results in a change of the natural flow of water without prior and specific approval. 5. The permit holder shall notify the Building and Inspection Services Division in accordance with established policy of all requ�ired inspections and shall not proceed or conceal work without written approval of such work from the Building and Inspection Services Division. 6. The issuance or granting of a permit shall not be construed to be a permit for, or an approval of, anviolation of any provision of any applicable code or any ordinance or regulation of this jurisdiction. Approval of work is subject to field inspection. Signature of Chief Building Official Date REQUESTS MUST BE MADE BY 11:59PM ANY BUSINESS DAY FOR INSPECTION THE FOLLOWING BUSINESS DAY. From: no-reolv(alci.wheatridae.m. us To: CommDev Perm is Subject: Online Form Submittal: Solar PV Installation Date: Thursday, October 8, 2020 5:15:30 AM Solar PV Installation This application is exclusively for Solar PV Installations YOU MUST ATTACH A VALID ELECTRONIC PAYMENT ORM IN ORDER FOR THE PERMIT TO BE PROCESSED. Your Permit will be emailed to the email address provided below once it is processed. THIS APPLICATION DOES NOT CONSTITUTE A PERMIT. DO NOT BEGIN WORK UNTIL PERMIT HAS BEEN ISSUED. Is this application for Yes Solar PV Installation? PROPERTY INFORMATION Property Address 3113 Teller St Property Owner Name Justin Wiley Property Owner Phone 303-667-6890 Number (enter WITH dashes, eg 303-123- 4567) Property Owner Email lwiley3408@gmail.com Address Attach City of Wheat Electronic Payment Form 3113 Teller St Wiley, Justin.Ddf Ridge Electronic Payment Form - "DO NOT ATTACH A PICTURE OF A CREDIT CARD" K�]X11:L'NlC�lal�l7il:�r�i/G\1[�7� Contractor Business Sunrun Installation Services Inc. Name Wheat Ridge 070159 Contractor's License Number (This is a 5 or 6 digit number for the City of Wheat Ridge) Contractor Phone Number (enter WITH dashes, eg 303-123- 4567) Contractor Email Address Retype Contractor Email Address DESCRIPTION OF WORK Scope of Work KW # of Panels Location of Panels Structural required Upload engineer letter or pages on 8 1/2" x 11" only Solar Installation Plan Set on 11'x17" only. Project Value (contract value or cost of ALL materials and labor) 720-537-0235 thomas.brook@sunrun.com thomas. brook@sunrun.com Roof mount, flush mount, grid -tied 13.545 MN solar PV 13.545 43 roof No PE Documents 3113 Teller St Wiley, Justin Rev A.odf PV Plans 3113 Teller St Wiley, Justin Rev A.odf 25735 SIGNATURE OF UNDERSTANDING AND AGREEMENT I assume full Yes responsibility for compliance with applicable City of Wheat Ridge codes and ordinances for work under any permit issued based on this application. I understand that work Yes may not begin on this property until a permit has been issued and posted on the property. I certify that I have Yes been authorized by the legal owner of the property to submit this application and to perform the work described above. Person Applying for Thomas Brook Permit I attest that everything Yes stated in this application is true and correct and that falsifying information in this application is an act of fraud and may be punishable by fine, imprisonment, or both. Email not displaying correctly? View it in your browser. K.". MLMUum _ wpmeaummwinmememglwmixsp '°"rt'r=P^ i..vw�ar�.e.ImereNe�Mw'uornmormctMnolo6YMwreR, u.�crm.muer�+run.ary~ •mmi o_ssxnrnzs LONGI Solar M n MualMtlw IN W IM1 IMrepmllNarrtM wn u�n.e wa ie�q_m.imrnwiwr IM.rw.py.1/WmlwerererttlNMrerairt f n + MUMMpiYM�epYnMNnY.l dµ, mCMerereMq arrtw LONGI Solar M n 996 8 g 0 � 955 L Junction Box: IP67, three diodes Width: ±2mm Height:±lmm Output Cable: 4mm2, 300mm in length LR6-60HPH 300-320M Units: mmlinch) Cell Orientation: 120 (6x20) Tolerance: to 0: 1-2mm Junction Box: IP67, three diodes Width: ±2mm Height:±lmm Output Cable: 4mm2, 300mm in length Pitch -w.. tlmm STC NOCT Glass:Singleglass 9 p 3.2mm coated tempered glass b Frame: Anodized aluminumalloyfiame A-" Weight: 18.9kg NOCT Dimension:1683x996x35mm m Packaging: 30pcs per pallet 305 180pcs per 2t7GP 310 780pcs per 417HC Operational Temperature: -40 C -+85 C Power Output Tolerance: 0 - +5 W Voc and Isc Tolerance: ±3% Maximum System Voltage: DC1500V (IEC/UL) Maximum Series Fuse Rating: 20A Nominal Operating Cell Temperature: 45±2 C Safety Class: Class II Fire Rating: UL type 4 Model Number LR6-60HPH-300M LR6-60HPH-305M LR6-60HPH-310M LR6-60HPH-315M LR6-60HPH-320M Testing Condition STC NOCT STC NOCT 1 STC NOCT 1 STC NOCT 1 STC 1 NOCT Maximum Power (Pmax/W) 300 222.2 305 225.9 310 229.6 315 233.4 320 237.1 Open Circuit Voltage (Voc/V) 39.8 1 37.1 40.1 1 37.4 40.3 1 37.7 40.6 1 37.9 40.9 1 38.2 Short Circuit Current (Isc/A) 9.70 1 7.82 9.78 1 7.88 9.86 1 7.94 9.94 1 8.01 10.02 1 8.08 Voltage at Maximum Power (Vmp/V) 32.9 1 i 30.4 33.1 1 i 30.6 33.3 1 i 30.8 33.7 1 i 31.1 1 33.9 1 31.3 Current at Maximum Power (Imp/A) 9.13 1 7.32 9.21 1 7.38 9.30 1 7.46 9.36 1 7.50 9.43 1 7.56 Module Efficiency(%) 17.9 18.2 18.5 18.8 19.1 STC (Standard Testing Conditions): Irradiance 1000W/m2, Cell Temperature 251C, Spectra at AM1.5 NOCT (Nominal Operating Cell Temperature): Irradiance 80OW/m2, Ambient Temperature 20 C, Spectra at AM1.5, Wind at 1m/S Temperature Coefficient of Isc Temperature Coefficient of Voc Temperature Coefficient of Pmax +0.057%/ C -0.286%/ C -0.370%/'C Current -Voltage Curve (LR6-60HPH-310M) 10 8 6 - Cell Temp=25°C - Cell Temp=35°C v V 4 - Cell Temp=45°C - Cell Temp=55°C 2 - Cell Temp=65°C - Cell Temp=75°C 0 0 10 20 30 40 Voltage M LONGI Solar Front Side Maximum Static Loading Rear Side Maximum Static Loading Hailstone Test Power -Voltage Curve (LR6-60HPH-310M) 350 Cell remp.=25°C -Incident Irrad-1 000W/m' 800 Incident lrrdd.�00w/m' Incident Irrdd.�00W/m' 250 -Incident lrmd.=400W/m' Incident Irrad. 200W/ 200 `w 150 100 50 0 0 10 20 30 40 Voltage M 5400Pa 2400Pa 25mm Hailstone at the speed of 23m/s Current -Voltage Curve (LR6-60HPH-310M) 12 Celltemp�25°C 10 Incident Irrad. 1000W/m' 8 Incident Irrad: 800W/m' 6 Incident lrmd�600I v U 4 Incident lrradI 2 Incident Irrad_ 200W/m' 0 0 10 20 30 40 Voltage M Room 201, Building 8, Sandhill Plaza, Lane 2290, Zuchongzhi Road, Pudong C Tel:+86-21-61047332 Fax:+86-21-61047377 E-mail: module@longi-silicc Facebook: www.facebook.com/LONGi Solar Note: Due to continuous technical innovation, R&D and improvement, technical data above mentioned may be of modification accordingly. LONGI such modification at anytime without further notice; Demanding party shall request for the latest datasheet for such as contract need, and make it lawful documentation duly signed by both parties. V09 Data Sheet Enphase Microinverters Region: AMERICAS Enphase IQ7and IQ 7+ Microinverters The high-powered smart grid -ready Enphase IQ 7 MicroW and Enphase IQ 7+ MicroTM dramatically simplify the installation process while achieving the highest system efficiency. Part of the Enphase IQ System, the IQ 7 and IQ 7+ Microinverters integrate with the Enphase IQ EnvoyTM, Enphase IQ BatteryTM, and the Enphase EnlightenTImonitoring and analysis software. IQ Series Microinverters extend the reliability standards set forth by previous generations and undergo over a million hours of power -on testing, enabling Enphase to provide an industry-leading warranty of up to 25 years. Easy to Install • Lightweight and simple • Faster installation with improved, lighter two -wire cabling • Built-in rapid shutdown compliant (NEC 2014 & 2017) Productive and Reliable • Optimized for high powered 60 -cell and 72 -cell* modules • More than a million hours of testing • Class II double -insulated enclosure • UL listed Smart Grid Ready • Complies with advanced grid support, voltage and frequency ride -through requirements • Remotely updates to respond to changing grid requirements • Configurable for varying grid profiles • Meets CA Rule 21 (UL 1741 -SA) * The IQ 7+ Micro is required to support 72 -cell modules. To learn more about Enphase offerings, visit enphase.com EN PHAS E. Enphase IQ 7 and IQ 7+ Microinverters INPUT DATA Module compatibility Maximum input DC voltage Peak power tracking voltage Operating range Min/Max start voltage Max DC short circuit current (module Ise) Overvoltage class DC port DC port backfeed current PV array configuration Peak output power Maximum continuous output power Nominal (LL)voltage/range' Maximum continuous output current Nominal frequency Extended frequency range AC short circuit fault current over 3 cycles Maximum units per 20 A (LL)branch circuit' Overvoltage class AC port AC port backfeed current IQ7-60-2-US IQ7PLUS-72-2-US 235 W-350 W+ 235 W-440 W+ 60 -cell PV modules only 48V 27V -37V 16V -48V 22V/48V 15A 0A 60 -cell and 72 -cell PV modules 60V 27V -45V 16V -60V 22V/60V 15A 0A 1 x 1 ungrounded array; No additional DC side protection required; AC side protection requires max 20A per branch circuit 240 VA 290 VA Power Line Communication (PLC) 240 V / 208 V / 240 V / 208V / 211-264 V 183-229V 211-264 V 183-229 V 1.0 A (240 V) 1.15 A (208 V) 1.21 A (240 V) 1.39 A (208 V) 60 Hz 60 Hz - 47 - 68 Hz 47 - 68 Hz 5.8 Arms 5.8 Arms L 16 (240 VAC) 13 (208 VAC) 13 (240 VAC) 11 (208 VAC) 0A 0A Power factor setting 1.0 1.0 Power factor (adjustable) 0.85 leading... 0.85 lagging 0.85 leading... 0.85 lagging EFFICIENCY @240 V @208 V @240 V @208 V 97.6% 97.6% 97.5% 97.3% CEC weighted efficiency 97.0% 97.0% 97.0% 97.0% MECHANICAL DATA Ambient temperature range Relative humidity range Connector type (IQ7-60-2-US & IQ7PLUS-72-2-US) Dimensions(WxHxD) Weight Cooling Approved for wet locations Pollution degree Enclosure -40°C to +65°C 4% to 100% (condensing) MC4 (or Amphenol H4 UTX with additional Q -DCC -5 adapter) 212 mm x 175 mm x 30.2 mm (without bracket) 1.08 kg (2.38 lbs) Natural convection - No fans Yes PD3 Class II double -insulated, corrosion resistant polymeric enclosure Environmental category / UV exposure rating NEMA Type 6 / outdoor FEATURES Communication Power Line Communication (PLC) Monitoring Enlighten Manager and MyEnlighten monitoring options. Both options require installation of an Enphase IQ Envoy. Disconnecting means The AC and DC connectors have been evaluated and approved by UL for use as the load -break disconnect required by NEC 690. Compliance CA Rule 21 (UL 1741 -SA) UL 62109-1, UL1741/IEEE1547, FCC Part 15 Class B, ICES -0003 Class B, CAN/CSA-C22.2 NO. 107.1-01 This product is UL Listed as PV Rapid Shut Down Equipment and conforms with NEC -2014 and NEC -2017 section 690.12 and C22.1-2015 Rule 64-218 Rapid Shutdown of PV Systems, for AC and DC conductors, when installed according manufacturer's instructions. 1. No enforced DC/AC ratio. See the compatibility calculator at runs '//enphase com/en-us/support/module-compatibility. 2. Nominal voltage range can be extended beyond nominal if required bythe utility 3. Limits may vary Referto local requirementsto define the number of microinverters per branch in your area. To learn more about Enphase offerings, visit enphase.com v EN PHAS E. OO 2019 Enphase Energy. All rights reserved. All trademarks or brands used are the property of Enphase Energy, Inc. 2019-326 Data Sheet Enphase Networking Enphase IQ Combiner 3C (X-IQ-AM1-240-3C) U� LISTED learn more about Enphase offerings, visit enphase.com cay or The Enphase IQ Combiner 3CTM with Enphase IQ EnvoyTM and integrated LTE -M cell modem with 5 -year data plan consolidates interconnection equipment into a single enclosure and streamlines PV and storage installations by providing a consistent, pre- wired solution for residential applications. It offers up to four 2 -pole input circuits and Eaton BR series busbar assembly. Smart • Includes IQ Envoy for communication and control • Includes LTE -M cell modem and 5 -year data plan • Flexible networking supports Wi-Fi, Ethernet, or cellular • Optional AC receptacle available for PLC bridge • Provides production metering and optional consumption monitoring Simple • Reduced size from previous combiner • Centered mounting brackets support single stud mounting • Supports back and side conduit entry • Up to four 2 -pole branch circuits for 240 VAC plug-in breakers (not included) • 80 A total PV or storage branch circuits Reliable • Durable NRTL-certified NEMA type 3R enclosure • Five-year warranty • UL listed n ENPHASE. Enphase IQ Combiner 3C MODEL NUMBER IQ Combiner 3C X-IQ-AM1-240-3C IQ Combiner 3C with Enphase IQ Envoy- printed circuit board for integrated revenue grade PV production metering (ANSI C12.20 +/-0.5 0) and optional* consumption monitoring (+/-2.5 0). Includes Enphase Mobile Connect LTE -M cell modem and 5 -year data plan. A Plug -and -play industrial -grade cellular modem with data plan for systems up to 60 microinverters. (Available in the US, Canada, Mexico, Puerto Rico, and the US Virgin Islands, where there is adequate cellular service in the installation area.) ACCESSORIES and REPLACEMENT PARTS (not included, order separately) Consumption Monitoring* CT CT -200 -SPLIT Split core current transformers enable whole home consumption metering (+/- 2.5%). Circuit Breakers Supports Eaton BR210, BR215, BR220, BR230, BR240, BR250, and BR260 circuit breakers. BRK-10A-2-240 Circuit breaker, 2 pole, 10A, Eaton BR210 BRK-15A-2-240 Circuit breaker, 2 pole, 15A, Eaton BR215 BRK-20A-2P-240 Circuit breaker, 2 pole, 20A, Eaton BR220 EPLC-01 _ Power line carrier (communication bridge pair), quantity 2 XA-PLUG-120-3 Accessory receptacle for Power Line Carrier in IQ Combiner 3C (required for EPLC-01) XA-ENV-PCBA-3 Replacement IQ Envoy printed circuit board (PCB) for Combiner 3C ELECTRICAL SPECIFICATIONS 80A of distributed generation / 90A with IQ Envoy breaker included Rating Continuous duty System voltage 120/240 VAC, 60 Hz Eaton SR series busbar rating 125 A Max. continuous current rating (output to grid) 65A Max. fuse/circuit rating (output) 90A ' Branch circuits (solar and/or storage) Up to four 2 -pole Eaton BR series Distributed Generation (DG) breakers only (not included) Max. continuous current rating (input from PV) 64A Max. total branch circuit breaker rating (input) 80A of distributed generation / 90A with IQ Envoy breaker included Production Metering CT 200 A solid core pre-installed and wired to IQ Envoy MECHANICAL DATA Dimensions (WxHxD) 37.5 x 49.5 x 16.8 cm (14.75" x 19.5" x 6.63"). Height is 21.06" (53.5 cm) with mounting brackets. Weight 7.5 kg (16.5 lbs) Ambient temperature range -40° C to +46° C (400 to 115° F) Cooling Natural convection, plus heat shield Enclosure environmental rating Outdoor, NRTL-certified, NEMA type 3R, polycarbonate construction Wire sizes 20 A to 50 A breaker inputs: 14 to 4 AWG copper conductors • 60 A breaker branch input: 4 to 1/0 AWG copper conductors • Main lug combined output: 10 to 2/0 AWG copper conductors • Neutral and ground: 14 to 1/0 copper conductors Always follow local code requirements for conductor sizing. Altitude To 2000 meters (6,560 feet) INTERNET CONNECTION OPTIONS Integrated Wi-Fi 802.11b/g/n Ethernet Optional, 802.3, Cat5E (or Cat 6) UTP Ethernet cable (not included) Cellular Optional, CELLMODEM-01 (3G) or CELLMODEM-03 (4G) or CELLMODEM-M1 (4G based LTE -M) (not included) COMPLIANCE Compliance, Combiner UL 1741 CAN/CSA C22.2 No. 107.1 47 CFR, Part 15, Class B, ICES 003 Production metering: ANSI C12.20 accuracy class 0.5 (PV product Compliance, IQ Envoy UL 60601-1/CANCSA 22.2 No. 61010-1 * Consumption monitoring is required for Enphase Storage Systems To learn more about Enphase offerings, visit enphase.com 2019-05-31 8 002019 Enphase Energy- hase Energy -All rights reserved- Al l trademarks or brands in this document are registered by their respective owner ENPHAE S Astra v.1.10 September 3, 2020 CAT 1 Subject : Structural Certification for Proposed Residential Solar Installation. Job Number: 501 R-113WILE; Rev A Client: Justin Wiley Address: 3113 Teller St, Wheat Ridge, CO, 80033 Attn: To Whom It May Concern A jobsite survey of the existing framing system of the address indicated above was performed by a site survey team from Sunrun. Structural evaluation was based on site observations and the design criteria listed below. Design Criteria: • 2018 IRC/IBC/I EBC, ASCE 7-16 & 2018 NDS • Basic Wind Speed V = 107 mph, Exposure C • Ground Snow Load = 30 psf Based on this evaluation, I certify that the existing structure directly supporting the PV system is adequate to withstand all loading indicated in the design criteria above based on the requirements of the applicable existing building and/or new building provisions adopted/referenced above. Additionally, the PV module assembly and hardware supporting it have been reviewed to be in accordance with the manufacturer's specifications and verified to meet the minimum loading requirements referenced above. p,p O LIC - 4 7 5 NAL CRY of Digitally Signed on: 9/3/2020 _ w B�,a.�z.zaza 133 Technology Dr., Suite 100, Irvine, CA, 92618 1 P (949)383-0993 Results Summary (Hardware Check Includes Uplift Check on Attachments/Fastener, Structure Check Considers Main Structure) Orientation Attachment Spacing/Cantilever Configuration GoverniDCRng Result AR-01 Landscape 72/18 Staggered 56% Pass Portrait 48/12 Staggered 56% Pass Roofing Material Pitch Structure Check Comp Shingle 17° Pass Orientation Attachment Spacing/Cantilever Configuration GoverniDCRng Result AR-02 Landscape 72/18 Staggered 56% Pass Portrait 48/12 Staggered 56% Pass Roofing Material Pitch Structure Check Comp Shingle 17° Pass Orientation Attachment Spacing/Cantilever Configuration GoverniDCRng Result AR-03 Landscape 72/18 Staggered 56% Pass Portrait 48/12 Staggered 56% Pass Roofing Material Pitch Structure Check Comp Shingle 17° Pass Orientation Attachment Spacing/Cantilever Configuration GoverniDCRng Result AR-04 Landscape Portrait 72/18 48/12 Staggered Staggered 56% Pass 56% Pass Roofing Material Pitch Structure Check Comp Shingle 17° Pass SCOPE OF WORK GENERAL NOTES LEGEND AND ABBREVIATIONS TABLE OF CONTENTS PAGE * DESCRIPTION • SYSTEM SIZE: 13545WDC, 10320WAC • MODULES.(43)LONGI GREEN ENERGY TECHNOLOGY CO • ALL WORK SHALL COMPLY WITH 20181RC/IBC/IEBC, MUNICIPAL CODE, AND ALL MANUFACTURERS LISTINGSAND INSTALLATION INSTRUCTIONS. SOLAR MODULES SE SERVICE ENTRANCE PV-10 COVER SHEET PV-20 SITE PLAN LTD'. LR6-60HPH-315M • PHOTOVOLTAIC SYSTEM WILL COMPLY WITH NEC2020. • INVERTER(S): (43)ENPHASE ENERGY. Q1-60-24JS • ELECTRICAL SYSTEM GROUNDING WILL COMPLY WITH NEC 2020 MP MAIN PANEL PV-30 LAYOUT PV-31 MOUNTING DETAIL • RACKING: SNAPNRACK RLU, RL UNIVERSAL, SPEEDSEAL TRACK ON COMP, SEE DETAIL SNR-DC-00436 • PHOTOVOLTAIC SYSTEM IS UNGROUNDED. NO CONDUCTORS ARE SOLIDLY GROUNDED IN THE INVERTER. SYSTEM COMPLIES WITH 69035. SHIP MOUNT SP SUB-PANEL SNR MOUNT & SKIRT PV-0.0 ELECTRICAL PV5.0 SIGNAGE •MODULES CONFORM TO AND ARE LISTED UNDER UL 1103. LC PV LOAD CENTER ® CHIMNEY • INVERTER CONFORMS TO AND IS LISTED UNDER UL 1141. • RACKING CONFORMS TO AND IS LISTED UNDER UL 2703 SM SUNRUN METER 0 ATTIC VENT • SNAPNRACK RACKING SYSTEMS, IN COMBINATION WITH TYPE I, OR TYPE II MODULES, ARE CLASS FIRE RATED. • RAPID SHUTDOWN REQUIREMENTS MET WHEN INVERTERS AND ALL CONDUCTORS ARE WITHIN ARRAY BOUNDARIES PER NEC 69012(1). 0 FLUSH ATTIC VENT PM DEDICATED PV METER a PVC PIPE VENT INV INVERTER(S) ® METAL PIPE VENT U yr ry z • CONSTRUCTION FOREMAN TO PLACE CONDUIT RUN PER 690 31(G). • ARRAY DC CONDUCTORS ARE SIZED FOR DERATED CURRENT. ® T-VENT AC AC DISCONNECT(S) LIE—SATELLITE DISH U)� • 994 AMPS MODULE SHORT CIRCUIT CURRENT. • 15 53AMPS DERATED SHORT CIRCUIT CURRENT [690.8 (a),d 690.8 (b)]. 0 DC DISCONNECT(S) FIRE SETBACKS Zm E' • PV INSTALLATION COMPLIES WITH THE NEC 2020 ARTICLE 69012(B)(2). CB IQ COMBINER BOX HARDSCAPE CONTROLLED CONDUCTORS LOCATED INSIDE THE ARRAY BOUNDARY ARE - LIMITED TO 80 VOLTS WITHIN 30 SECOND OF A RAPID SHUTDOWN INITIATION F-1 INTERIOR EQUIPMENT —PL— PROPERTY LINE L-1 SHOWN AS DASHED SCALE NITS SUnrUn A AMPERE AC ALTERNATING CURRENT ur City of 2pcorm t[Z�dge MUNOT DEYEWhM6NT AFCI ARC FAULT CIRCUIT INTERRUPTER AZIM AZIMUTH COMP COMPOSITION DC DIRECT CURRENT EC #1686, ME #600088 VICINITY MAP Arvada APPROVED (E) EXISTING 5525 W56TH AVE Arvesseoareas ® _ Tor{ ReviewaGMr Code Compliance ESS ENERGY STORAGE SYSTEMo EXT EXTERIOR INT INTERIOR � NES 5407631 CUSTOMER RESIDENCE. ID 12�2D LBW LOAD BEARING WALL MAG MAGNETIC JUSTIN WILEY 3113 TELLER ST, WHEAT RIDGE, Plans Examiner Dale MSP MAIN SERVICE PANEL CO, 80033 ® wl memn: memue..e a/apnmedggraroloueHk mw (N) NEW Lakeside BE eery_, suxxv 0'O'O1AXoidAOvinae'eA1'•^Op'AOrk •°'^r°'°^°"iroNnv°4eOo"^'"Nt>^^^vo aa�b <^r •obna7m �ramewwrau aide eunawgero•aa M�avaA�ms. Ali yre..nnpegx•omnwlryroeweeeven<x/mq.wuxR grM�wyp NTS NOT TOSCALE OC ON CENTER PRE-FAB PRE-FABRICATED PSF POUNDS PER SQUARE FOOT PV PHOTOVOLTAIC TEL (303) 6676890 APN #.21548 PROJECT NUM BER. 501 R-113WILE 3113 Teller Street TL TRANSFORMERLESS TYR TYPICAL DESIGNER. (415)580-Begg ex3 Approval Notes 1) ON gray system ta have grounding system installed per PartIII of Article 250 per202o NECAUde 69047G). V VOLTS `^/ WATTS MARGARET CAULEY SHEET REV NAME DATE COMMENTS EftewanN EIRch Gardena rempprarlil ed 2) If JFER ground in not available provide orvenry supplemental ground rods per 2020 NECAUde 250 EERIE). 3) Cold Hof Wafer& Natural Gas bonding per 2020 NEC goals 250.101 COVER SHEET REV.A 01-Sep-20 nunnsl PAGE PV-1.0 SITE PLAN - SCALE = 3164" = 1'0" Pi v PL NOTE: MICRO -INVERTERS INSTALLED UNDER EACH MODULE PL (E) RESIDENCE (N) ARRAY AR -03 �L SE (N) ARRAY AR -01 ROOF PATHWAYS (3' TYP) `' a a.a a . a: ... .. i. • A.' .. .. q. .a a, •t. .. 4 •a ee•. e. •4, J e .9' Lu.... .. .. a ,. .. i.. A. a , ...a'• ^� ..a .. ..a. .. .. . (E) A/C UNIT ROOF PATHWAYS (3' TYP) A m (N) ARRAY AR -02 �L (N) ARRAY AR -04 FIRE SETBACKS (3' TYP) NOTES: • RESIDENCE DOES NOT CONTAIN ACTIVE FIRE SPRINKLERS. ARRAY DETAILS: • TOTAL ROOF SURFACE AREA: 1777 SQFT. • TOTAL PV ARRAY AREA: 775.9 SQ FT. • PERCENTAGE PV COVERAGE: (TOTAL PV ARRAY AREAITOTAL ROOF SURFACE AREA)' 100 = 43.7% ROOF INFO FRAMING INFO ATTACHMENT INFORMATION DESIGN CRITERIA Name Type Height Type Max OC Detail Max Landscape Max Landscape Max Portrait Max Portrait Configuration MAX DISTRIBUTED LOAD: 3 PSF Span Spacing OC Spacing Overhang OC Spacing Overhang SNOW LOAD: 30 PSF WIND SPEED: AR -01 COMP SHINGLE - RLU 2 -Story 2X6 RAFTERS 13'- 24 RL UNIVERSAL, SPEEDSEAL TRACK ON 6' - 0" 1' - 6" 4' - 0" 1' -011 STAGGERED 107 MPH 3 -SEC GUST. 10" COMP, SEE DETAIL SNR -DC -00436 S.S. LAG SCREWS: 13'- RL UNIVERSAL, SPEEDSEAL TRACK ON 5/16": 2.5" MIN EMBEDMENT AR -02 COMP SHINGLE -RLU 2 -Story 2X6 RAFTERS 10" 24„ COMP, SEE DETAIL SNR -DC -00436 6' - 0" 1' - 6" 4' - 0" 1' - 0" STAGGERED STRUCTURAL NOTES: • INSTALLERS TO VERIFY AR -03 COMP SHINGLE - RLU 2 -Story 2X6 RAFTERS 13'.- 2411 RL UNIVERSAL, SPEEDSEAL TRACK ON 6' - 0" 1' - 6" 4' - 0" 1' - 0" STAGGERED RAFTER SIZE, SPACING AND 10, COMP, SEE DETAIL SNR -DC -00436 SLOPED SPANS, AND NOTIFY 13'- RL UNIVERSAL, SPEEDSEAL TRACK ON E.O.R. OF ANY AR -04 COMP SHINGLE -RLU 2 -Story 2X6 RAFTERS 10" 24 COMP, SEE DETAIL SNR -DC -00436 6' - 0" 1' - 6" 4' - 0" 1' - 0" STAGGERED DISCREPANCIES BEFORE PROCEEDING. D1 - AR -01 - SCALE: 3/32" = V-0" D2 - AR -02 - SCALE: 3/32" = V-0" • IF ARRAY (EXCLUDING PITCH: 17° PITCH: 17° SKIRT) IS WITHIN 12" AZIM:O° AZIM:180° (E) A/C UNIT BOUNDARY REGION OF ANY ROOF PLANE EDGES 11'-1" —5'-6"— 19'-8" 3" 13'-3" 15'-2" (EXCEPT VALLEYS), THEN ATTACHMENTS NEED TO BE ADDED AND OVERHANG 3'-3"4,14„ REDUCED WITHIN THE 12" BOUNDARY REGION ONLY AS FOLLOWS: •• ALLOWABLE ATTACHMENT 4' TYP. SPACING INDICATED ON 29'-11" 12'-2" PLANS TO BE REDUCED BY E34' TYP. 6' TYP. � •• ALLOWABLE OVERHANG INDICATED ON PLANS TO BE 1/5TH OF ALLOWABLE 27'-10" —4'— —5'-6"— —6'-1"—-6" 13'-3" T T 3'-" 5" J L 13'-3" —8'-6"—� L1, ATTACHMENT SPACING INDICATED ON PLANS 1'-9" 3'-3 sunrun D3 - AR -03 - SCALE: 3/32" = V-0" D4 - AR -04 - SCALE: 3/32" = V-0" PITCH: 17° PITCH: 17° EC #7080, ME #600088 AZIM:270° AZIM:90° 55s5w540E,ARVADA,coefififiz PHONE 805 ]631 805 540 FAX 0 CUSTOMER RESIDENCE: �pDO L.C.. ^E102'-8" 31 V�gP MASS�G FQ 3113 TETIN LLELEY R ST, WHEAT RIDGE, CO, 80033 61-111 t 47••• rJ• EL. (303) 667-6890 i 9'-11" .: 2 PN #: 21548 • 6 7 PROJECT NUMBER: 501 R-113WILE — 6' TYP.- — 6' TYP./ONAUE Digitally Signed: 09/0320 DESIGNER. (415)580-6920 ex3 MARGARET CAULEY CRY of SHEET LAYOUT - REV: A 01 -Sep -20 SEE SITE PLAN FOR NORTH ARROW PAGE PV -3.0 SNAPNRACK RL UNIVERSAL SPEEDTRACK COMPOSITION ROOF MOUNTING 0 5/16" S.S. LAG SCRE1 EMBED 0 5/16" LAG SCREW 2-1/2" INTO THE ROOF STRUCTURAL MEMBER/RAFTER FOR TORQUE SPECIFICATIONS SEE INSTALLATION MANUAL FOAM GASKET 0 5/16" S.S. LAG SCREW 2-1/2" MINIMUM EMBEDMENT ROOF RAFTER(TYP.) ROOF ATTACHMENTS SHALL BE EMBEDDED INTO ROOF RAFTERS OR OTHER STRUCTURAL MEMBERS PILOT HOLE CENTER OF COURSE ROOF SHEATHING, UNDERLAYMENT, AND ROOFING MATERIAL (TYP.) ((((�� Sunrun South LLC DESIGNER: B.PETERSON snaL rack- '"°"EPP'E®°®° FAXA5)®O6� °� DRAFTER B.PETERSON Solar Mounting SolutionsRTARY ANY WRITTEN CONSENT OF SUNRUN SOUTH YYC ""°°"" APPROVED BY: W.ARBUCKLE REVISION: 1 11/11/2019 NEW DETAIL BDP RACK m =S SPEEDTRACK SHOULD BE INSTALLED PARALLEL TO RAFTER 2-1/2" MIN. EMBEDMENT - INTO RAFTER OR STRUCTURAL MEMBER COMPLETED INSTALLATION SECTION VIEW ROOFING MATERIAL COMPLETED INSTALLATION SCALE: NTS PART NUMBER: I DESCRIPTION: SNR -DC -00436 RL UNIVERSAL, ATTACHMENT DETAIL, MOUNT DATE: 11/11/2019 d SPEEDTRACK ON COMP Digitally Signed: 09/0320 DECKING REV: sunrun EC #7080, ME #600088 5525 w 56TH AVE, ARVADA, C080002 PHONE 865 546 7631 FAX 6 CUSTOMER RESIDENCE: JUSTIN WILEY 3113 TELLER ST, WHEAT RIDGE, CO, 80033 TEL. (303) 667-6890 APN #:21548 PROJECT NUMBER: 501 R-113WILE DESIGNER: (415) 580-6920 ex3 MARGARET CAULEY SHEET MOUNTING DETAIL REV: A 01 -Sep -20 PAGE PV -3.1 120/240 VAC SINGLE PHASE SERVICE METER M XCEL D9S 47435 UTILITY GRID SUPPLY SIDE TAP EXISTING 125A MAIN BREAKER 1 EXISTING _ 125A MAIN FACILITY PANEL LOADS Approval Notes: 1) PN array system to have grounding system installed per Part III of Article 250 per 2020 NEC Article 690.47(A). 2) If LIFER ground in not available provide or verify supplemental ground rods per 2020 NEC Article 250.53(A)(3). 3) Cold & Hot Water & Natural Gas bonding per 2020 NEC Article 250.104(A)(B) [VISIBLE OPEN] (N)LOCKABLE BLADE TYPE FUSED AC DISCONNECT 60A FUSES SQUARE D D222NRB 3R, 60A 120/240VAC [MAX 10' FROM UTILITY METER] [READILY ACCESSIBLE MEANS FOR RAPID SHUTDOWN] (N) DEDICATED PV KWH METER O 240V METER SOCKET 200A CONTINUOUS WITH LEVER BYPASS [MAX 10' FROM UTILITY METER] (N) 125A ENPHASE IQ AC COMBINER BOX WITH INTEGRATED 10A ENVOY BREAKER 3CX-IQ-AM 1-240-3C 2 20A BREAKER [A] 20A BREAKER [B] 20A BREAKER [C] CONDUIT SCHEDULE # CONDUIT CONDUCTOR NEUTRAL GROUND 1 NONE (2) 12 AWG PER ENPHASE Q NONE (1) 10 AWG BARE COPPER 33.7 V SHORT CIRCUIT CURRENT: CABLE BRANCH IQ7-60-2-US --- --- --- �. - - -- (1) BRANCH OF (16) (2) 12 AWG PER ENPHASE Q MICRO -INVERTERS [A] (1) 8 AWG THHN/THWN-2 2 3/4" EMT OR EQUIV. I� NONE MICRO -INVERTERS [B] CABLE BRANCH EGC/GEC 3 3/4" EMT OR EQUIV. (2) 6 AWG THHN/THWN-2 (1) 6 AWG THHN/THWN-2 (1) 6 AWG THHN/THWN-2 EGC/GEC MODULE CHARACTERISTICS LONGI GREEN ENERGY ,f✓f if.�f TECHNOLOGY CO LTD: TECHNOLOGY CO LTD: LR6-60HPH-315M MODULES LR6-60HPH-315M: 315 W OPEN CIRCUIT VOLTAGE: 40.6 V MAX POWER VOLTAGE: 33.7 V SHORT CIRCUIT CURRENT: 9.94 A JUNCTION BOX OR EQUIVALENT GENERAL NOTES: • CONNECT SYSTEM VIA INSULATION PIERCING ON SUPPLY SIDE OF MAIN BREAKER IN MAIN PANEL ENCLOSURE. CONDUCTORS ARE FIELD INSTALLED. • • FIELD SPLICE WIRE TO APPROPRIATE SIZE FOR MANUFACTURE TERMINATION SPECIFICATIONS WHEN NEEDED. • WIRE UPSIZE AT TIME OF INSTALLATION IS PERMISSIBLE. (43) LONGI GREEN ENERGY ,f✓f if.�f + ifilf TECHNOLOGY CO LTD: LR6-60HPH-315M MODULES AND MICRO -INVERTER PAIRS (43) ENPHASE ENERGY: IQ7-60-2-US --- --- --- �. - - -- (1) BRANCH OF (16) MICRO -INVERTERS [A] CC (1) BRANCH OF (15) I� MICRO -INVERTERS [B] (1) BRANCH OF (12) MICRO -INVERTERS [C] • CONNECT SYSTEM VIA INSULATION PIERCING ON SUPPLY SIDE OF MAIN BREAKER IN MAIN PANEL ENCLOSURE. CONDUCTORS ARE FIELD INSTALLED. • • FIELD SPLICE WIRE TO APPROPRIATE SIZE FOR MANUFACTURE TERMINATION SPECIFICATIONS WHEN NEEDED. • WIRE UPSIZE AT TIME OF INSTALLATION IS PERMISSIBLE. I &WARNING 1 ELECTRICAL SHOCK HAZARD TERMINALS ON LINE AND LOAD SIDES MAY BE ENERGIZED IN THE OPEN POSITION LABEL LOCATION: INVERTER(S), AC DISCONNECT(S), AC COMBINER PANEL (IF APPLICABLE). PER CODE(S): NEC 2020: 690.13(B), NEC 2017: 690.13(B), NEC 2014: 690.17(E), NEC 2011: 690.17(4) LABEL LOCATION: UTILITY SERVICE ENTRANCE/METER, INVERTER/DC DISCONNECT IF REQUIRED BY LOCAL AHJ, OR OTHER LOCATIONS AS REQUIRED BY LOCAL AHJ. PER CODE(S): NEC 2020: 690.56(c)(2), NEC 2017: 690.56(C)(3), NEC 2014: 690.12, NEC 690.56, IFC 2012: 605.11.1, IFC 2018: 1204.5.3 &WARNING POWERSOURCE OUTPUTCONNECTON DO NOT RELOCATE THIS OVERCURRENT DEVICE LABEL LOCATION: ADJACENT TO PV BREAKER AND ESS OCPD (IF APPLICABLE). PER CODE(S): NEC 2020: 705.12(B)(3)(2), CEC 2019: 705.12(13)(2)(3)(b), NEC 2017: 705.12(13)(2)(3)(b), CEC 2019:705.12(B)(3), NEC 2017: 705.12(B)(3), NEC 2014: 705.12(B)(3), NEC 2011: 705.12(D)(7) LABEL LOCATION: AC DISCONNECT(S), PHOTOVOLTAIC SYSTEM POINT OF INTERCONNECTION. PER CODE(S): NEC 2020: 690.54, NEC 2017: 690.54, NEC 2014: 690.54, NEC 2011: 690.54 3" SOLAR PV SYSTEM EQUIPPED WITH RAPID SHUTDOWN TURN RAPID SHUTDOWN SWITCH TO THE "OFF" POSITION TO SHUT DOWN PV SYSTEM AND REDUCE SHOCK HAZARD IN THE ARRAY. LABEL LOCATION: ON OR NO MORE THAT 1 M (3 FT) FROM THE SERVICE DISCONNECTING MEANS TO WHICH THE PV SYSTEMS ARE CONNECTED. PER CODE(S): CEC 2019: 690.56(C)(1)(a), NEC 2017: 690.56(C)(1)(a) NOTES AND SPECIFICATIONS: • SIGNS AND LABELS SHALL MEET THE REQUIREMENTS OF THE NEC 2020 ARTICLE 110.21(B), UNLESS SPECIFIC INSTRUCTIONS ARE REQUIRED BY SECTION 690, OR IF REQUESTED BY THE LOCAL AHJ. • SIGNS AND LABELS SHALL ADEQUATELY WARN OF HAZARDS USING EFFECTIVE WORDS, COLORS AND SYMBOLS. • LABELS SHALL BE PERMANENTLY AFFIXED TO THE EQUIPMENT OR WIRING METHOD AND SHALL NOT BE HAND WRITTEN. • LABEL SHALL BE OF SUFFICIENT DURABILITY TO WITHSTAND THE ENVIRONMENT INVOLVED. • SIGNS AND LABELS SHALL COMPLY WITH ANSI Z535.4-2011, PRODUCT SAFETY SIGNS AND LABELS, UNLESS OTHERWISE SPECIFIED. • DO NOT COVER EXISTING MANUFACTURER LABELS. CAUTION: MULTIPLE SOURCES OF POWER SOLAR PANELS AND MICRO INVERTERS ON ROOF ENPHASE IQ AC COMBINER BOX MAIN PANEL AND PV PV PRODUCTION METER J BREAKER DISCONNECT FUSED AC DISCONNECTJ L "RAPID SHUTDOWN" SERVICE ENTRANCE 3113 TELLER ST, WHEAT RIDGE, CO, 80033 PER CODE(S): NEC 2020 and NEC 2017: 705.10 + 710.10 1, a.VI 2-2-02-0 INSPECTION RECORD Inspection online form: http://www.cl.wheatridge.co-us/inspection Cancellations must be submitted via the online form before 8 a.m. the day of the inspection Inspections will not be performed unless this card is posted on the project site Request an inspection before MIDNIGHT (11:5 PM) to rer�;We an inspection the following business day PERMIT: r ADDRESS: I /I �.� �J JOB CODE: Foundation Inspections Date Inspector CommentsInitials 102 Caissons / Piers 103 Footing / P.E. Letter 104 Foundation Setback Cert. WIWI PJ 105 Stem Walls 106 Foundation wall Insulation Do Not Pour Concrete Prior To Approval Of The Above Inspections Underground /Slab Inspections Date Inspector CommentsInitials 201 Electrical / Cable/ Conduit 202 Sewer Underground Int. 203 Sewer Underground Ext. WIWI PJ 204 Plumbing Underground Int. X205 Plumbing Underground Ext. 206 Water Underground Do Not Cover Underground or Below / In -Slab Work Prior To Approval Of The Above Inspections Rough Inspection Date Inspector CommentsInitials 301 Rough Framing 302 Wall Sheathing 303 Roof Sheathing 304 Sheer Inspection WIWI PJ 305 Insulation 306 Mid -Roof 307 Metal / Lath / Stucco 308 Rough Electrical Residential 309 Rough Electrical Commercial 310 Electrical Meter Residential 311 Electrical Meter Commercial 312 Temp. Const. Meter 313 Rough Plumbing Residential 314 Rough Plumbing Commercial 315 Shower Pan SEE OVER FOR ADDITIONAL INSPECTIONS PERMIT / e ( u"- �� ADDRESS: E'� �� kk "� JOB CODE:' f� ,. Rough Inspection continued g p Date Inspector Initials Comments 316 Rough Mechanical Residential 317 Rough Mechanical Commercial 318 Boiler/ urnace 319 Hot water tank 320 Drywall screw and Nail 321 Moisture board / shower walls 322 Rough Grading 323 Miscellaneous Final Inspections Date Inspector Initials Comments 401 Gasline 402 Gas Meter Release 403 Final Electrical Residential 404 Final Electrical Commercial 405 Final Mechanical Residential 406 Final Mechanical Commercial 407 Final Plumbing Residentiai 408 Final Plumbing Commercial 409 Final Roof 410 Final Window/Door 411 Landscape/Park/Planning" Inspections from these entities shall be requested one week in advance. *For landscaping and parking inspections please call 303-235-2846 **For ROW and drainage inspections please call 303-235-2861 ***For fire inspections please contact the Fire Protection District for your project. 412 Row/Drainage/Public Works" 413 Flood plain Inspection** 414 Fire Insp. /Fire Protection*** 415 Public Works Final** 416 Storm Water Mgmt.** 417 Zoning Final Inspection* 418 Building Final Inspection Note: All items must be completed and approved by Planning, Public Works, Fire and Building before a Certificate of Occupancy is issued. Approval of the Final Building Inspection does not constitute authorization of occupancy. For Low Voltage permits please be sure that rough inspections are completed by the Fire District and Electrical low voltage by the Building Division. f 41 i CITY OF WHEAT RIDGE Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: q0q - F'� r Uv� Job Address: 31 r 3 -f I Poe' Si, Permit Number: _Z010006g6 6 ❑ No one available for inspection: Time ' _)y j1AK4/PM Re -Inspection required: Yes No When corrections have been made, call for re -inspection at 303-234-5933 Date: -(-I L � f 10 Inspector: bye tyyrff DO NOT REMOVE THIS NOTICE i CITY OF WHEAT RIDGE _:�9�Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTIC Inspection Type: Job Address: 31 / T' //P/ S Permit Number: a ❑ No one available for inspection: TiMe / M/PM Re -Inspection required: Yes (N07) When correcti ns have been made, call for re inspection at 303-234-5933 Date: '� / % Inspector: MT DO NOT REMOVE THIS NOTICE i City of Wheat Ridge Residential Roofing PERMIT - 201800696 PERMIT NO: 201800696 ISSUED: 03/12/2018 JOB ADDRESS: 3113 Teller ST EXPIRES: 03/12/2019 JOB DESCRIPTION: Residential reroofing permit remove and install Owens Corning Laminated Asphalt Shingles with redecking 23squares. Pitch=4/12 *** CONTACTS *** OWNER (720)296-0724 SUPIT JEFFREY SUB (719)985-2110 Brad Griebenow 170132 DBA Storm Guard of Co. Sprgs *** PARCEL INFO *** ZONE CODE: UA / Unassigned USE: UA / Unassigned SUBDIVISION CODE: 140 / Converted Residences; 0 BLOCK/LOT#: 0 / *** FEE SUMMARY *** ESTIMATED PROJECT VALUATION: 13,200.00 FEES Total Valuation 0.00 Use Tax 277.20 Permit Fee 267.70 ** TOTAL ** 544.90 *** COMMENTS *** *** CONDITIONS *** Midroof & Final Roof inspections for ROOFS 6/12 PITCH & OVER: 3rd party inspection will be required for both the midroof and final inspections. The 3rd party inspection report AND THE ORIGINAL PERMIT CARD needs to be dropped off to the Permit Desk at the City of Wheat Ridge. The report MUST BE SIGNED by the Homeowner. REGARDING ROOF VENTILATION: Roof ventilation shall comply with IBC Sec. 1203.2 or IRC Sec. R806. The installation of ridge venting requires the installation or existence of soffit venting. For calculation purposes, one hat or turtle vent equal to one-half of one square foot of opening. Effective December 1, 2014, asphalt shingle installations require an approved midroof inspection, conducted when 25-75 percent of the roof covering is installed, prior to final approval. Installation of roof sheathing (new or overlay) is required on the entire roof when spaced or board sheathing with ANY gap exceeding one half inch exists. Sheathing and mid -roofs may be called in at the same time, one hundred percent of the sheathing must be complete and 25-75 percent of the mid -roof may be complete. Asphalt shingles are required to be fastened to the roof deck with a minimum of 6 nails per shingle. Ice and water shield is required. Eave and rake metal is required. A ladder extending 3 feet above the roof eave and secured in place is required to be provided for all roof inspections. Roof ventilation is required to comply with applicable codes and/or manufacturer installation instructions, whichever is more stringent. In order to pass a final inspection of elastomeric or similar type roof coverings, a letter of inspection and approval from the manufacturer technical representative stating that "the application of the roof at (project address) has been applied in accordance with the installation instruction for (roof material brand name) roof covering" is required to be on site at the time of final inspection. City of Wheat Ridge Residential Roofing PERMIT - 201800696 PERMIT N0: 201800696 ISSUED: 03/12/2018 JOB ADDRESS: 3113 Teller ST EXPIRES: 03/12/2019 JOB DESCRIPTION: Residential reroofing permit remove and install Owens Corning Laminated Asphalt Shingles with redecking 23squares. Pitch=4/12 I, by my signature, do hereby attest that the work to be performed shall comply with all accompanying approved plans and specifications, applicable building codes, and all applicable municipal codes, policies and procedures, and that I am the legal owner or have been authorized by the legal owner of the property and am authorized to obtain this permit and perform the work described and approved in conjunction with this,permit. I further attest that I am legally authorized to include all entities named within this document as parties to the work to be performed and that all work to be pelformed is disclosed in this document and/or its' accompanying approved plans and specifications. Signature'of OWNER or CONTRACTOR (Circle one) Date 1. This permit was issued based on the information provided in the permit application and accompanying plans and specifications and is subject to the compliance with those documents, and all applicable statutes, ordinances, regulations, policies and procedures. 2. This permit shall expire 365 days after the date of issuance regardless of activity. Requests for extension must be made in writing and received prior to the date of expiration. An extension of no more than 180 days made be granted at the discretion of the Chief Building Official and may be subject to a fee equal to one-half of the originalpermit fee. 3. If this permit expires, a new permit may be required to be obtained. Issuance of a new permit shall be subject to the standard requirements, fees androcedures for approval of any new permit. Re -issuance or extension of expired permits is at the sole discretion of the Chief Building Official and is not guaranteed. 4, No work of an manner shall be performed that shall results in a change of the natural flow of water without prior and specific approval. 5. The permit holymm der shall notify the Building and Inspection Services Division in accordance with established policy of all required inspections and shall not proceed or conceal work without written approval of such work from the Building and Inspection Services Division-.,, 6. The issuance of ' ra fllir g of a permit shall not be construed to be a permit for, or an approval of, any violation of any provision of any applicable code or any ordinancejbr regulation of this jurisdiction. Approval of work is subject to field inspection. 90 Signature of Chief Building Offici'aih d` ,� Date REQUESTS MUST BE MADE BY 11: 9PM ANY BUSINESS DAY FOR INSPECTION THE FOLLOWING BUSINESS DAY. Dina Kem C'I�OC� From: no-reply@ci.wheatridge.co.us Sent: Monday, March 12, 2018 11:40 AM To: CommDev Permits Subject: Online Form Submittal: Residential Roofing Permit Application Categories: Gina Residential Roofing Permit Application This application is exclusively for new permits for residential roofs and for licensed contractors only. This type of permit is ONLY being processed online --do not come to City Hall to submit an application in person. Permits are processed and issued in the order they are received and due to the volume of requests, time to process varies and is subject to change. YOU WILL BE CONTACTED WHEN YOUR PERMIT IS READY FOR PICK-UP AND WILL BE GIVEN A SPECIFIC DATE AND TIME WINDOW TO COMPLETE THE TRANSACTION. You will be notified if your contractor's license or insurance has expired, and you may update those documents at the time you are issued your permit. For all other requests: Homeowners wishing to obtain a roofing permit must apply for the permit in person at City Hall. Revisions to existing permits (for example, to add redecking) must be completed in person at City Hall. All other non -roofing permits must be completed in person at City Hall. The Building Division will be open from 7:30-10:30 a.m., Monday through Friday to process these types of requests. THIS APPLICATION DOES NOT CONSTITUTE A PERMIT. DO NOT BEGIN REROOFING UNTIL PERMIT HAS BEEN ISSUED. Is this application for a Yes residential roof? How many dwelling units Single Family Home are on the property? PROPERTY INFORMATION Property Address 3113 feller St c C ✓ �� Property Owner Name Jeff Supit Property Owner Phone 720-296-0724 Number (enter WITH 9 dashes, eg 303-123-4567) -1 Property Owner Email jeff.supit@outlook.com Address Do you have a signed Yes contract to reroof this property? Applications cannot be submitted without an executed contract attached below. Attach Copy of Executed Supit - Contract.pdf Contract Contractor Business Storm Guard Name Contractor's License 170132 Number (This is a 5 or 6 digit number for the City of Wheat Ridge) Contractor Phone 303-223-5719 Number (enter WITH dashes, eg 303-123-4567) Contractor Address 11152 Huron St #211 Northglenn, CO 80234 (Primary address of your business) Contractor Email Address rmoore@stormguardre.com Retype Contractor Email rmoore@stormguardre.com Address DESCRIPTION OF WORK TOTAL SQUARES of 23 the entire scope of work: Project Value (contract 13200 value or cost of ALL materials and labor) Are you re -decking the Yes / roof? Is the permit for a flat Pitched roof (2:12 pitch or greater) roof, pitched roof, or 2 both? (check all that apply) What is the specific pitch 4/12 of the PITCHED roof? How many squares are part of the PITCHED roof? Describe the roofing materials for the PITCHED roof: Type of material for the PITCHED roof: Provide any additional detail here on the description of work. (Is this for a house or garage? Etc) a I I I -- Owens Corning Laminated shingles Aspha#-' Will tear off t -lock shingles and upgrade to laminated shingles and house has spaced decking so will be a complete re -deck on roof SIGNATURE OF UNDERSTANDING AND AGREEMENT I assume full Yes responsibility for compliance with applicable City of Wheat Ridge codes and ordinances for work under any permit issued based on this application. I understand that this Yes application is NOT a permit. I understand I will be contacted by the City to pay for and pick up the permit for this property. I understand that work Yes may not begin on this property until a permit has been issued and posted on the property. I certify that I have been Yes authorized by the legal 3 owner of the property to submit this application and to perform the work described above. I attest that everything Yes stated in this application is true and correct and that falsifying information in this application is an act of fraud and may be punishable by fine, imprisonment, or both. Name of Applicant Roxanna Moore Email not displaying correctly? View it in your browser. Office/Fax: 303-223-5719 11152 Huron Street #211 Northglenn, CO 80234 www.stormcivardrestoration.com ,. EXTERIOR RESTORATION N Licensed • Bonded • Insured 1314 Contingency Contract (This Contract is Contingent Upon Your Insurance Company's Approval of Your Claim) Homeowner Name 1: S" _ Homeowner Name 2: Address: 31 13 _ City* OAT_riJ!� Zip: 900.3 Contact Home: `7 Itj,. 7') - (�� - Work: Cell: Email Address: EXISTING ROOF SPECIFICATIONS Roof Condition: 3 tab Arch. YR Other 7r- Loci. *Color Pitch _ /12 *2 Story Yes _ No Tear Off: All Felt I Lb. LF Valley LF Ridge 750 Vents # Power Vents # Plumbing Boots Total # 1" 2" 3" LF Drip Edge _ Color Remove Debris ✓ Roll Yard Protect Landscape '� Furnish Permit i✓ NEW SHINGLE COLOR BRAND 3 tab Archt. Customer EXISTING SIDING SPECIFICATIONS Siding Condition: Type of siding: Brick Vinyl Wood Steel Aluminum Style of Siding: Lap Dutch Grained Foam Backer Wrap None LF Fascia Color LF Soffit Color Vented Plain NEW SIDING COLOR BRAND STYLE Customer Int. SPECIAL CONCERNS: ---------------------------------------------- Acknowledgement: Payment Schedule: Payments Received: By signature below, Homeowner agrees to ; Deductible $ 100 Q M Date: Amount $ pay Storm Guard the RCV/ACV amount Cuyrt, Suppl. $ Date: Amount $ specified in the statement of loss for ; Mat. Upgrades $ Date: Amount $ roofing/siding as a materials deposit prior ; Material Deposit $ Date: Amount $ to construction. Homeowner agrees Storm Mat. Tax Base Service Charge $ Date: Amount $ Guard is entitled to contractors' "Overhead & Profit", material tax and base service charge ; Final Payment TBD that is paid by cpm the insurance n by Insurance Company Date: Amount $ - ------------- - y--------- **Your warranty rights are contingent upon our receipt of full payment for the Work. See Terms and Conditions, Sections 3, on the reverse side of this contract. ACCEPTANCE OF AGREEMENT o 11 c # tc r/ooS / By signing this Contingency Contract, you agree to authorize Storm Guard to assist you in your pursuit of a claim under your insurance policy and your efforts to reach agreement with your insurer on project scope and price. You may cancel this contract with no penalty by providing written notice before midnight on the third business day after the date of your signature below, or any time before your insurer approves your claim, whichever is later. You have no obligation to Storm Guard under this Contract unless your insurer -approves your claim and Storm Guard approves the scope and price identified on the loss statement you receive from your insurer. If your insurer approves your claim, and if Storm Guard approves the scope and price identified on the loss statement you receive from your insurer, then, by signing below, you authorize Storm Guard to complete the replacement of damaged property identified on the loss statement with no additional cost to you except for your insurance deductible, subject to the terms and conditions on the reverse side of this Contract. Payments must be made as outlined above. If this proposal is not accepted within thirty (30) days, it shall be automatically withdrawn. Accepted by Homeowner on d to _ r i l Homeowner Signature # Homeowner Signature #2 Insurance Company: 41�' VPt'hSh-h Claim Number: Q CC 17 3 5-7-7o Mortgage Company: — Loan Number: Phone: Sales Representative: S� Field Manager: J C (Oaa �jo finoT 9-7 2A9 - �O1 %0 C6onn�1 @ v�`►Gi�nM . City of Wheat Ridge Residential Roofing PERMIT - 201800707 PERMIT NO: 201800707 ISSUED: 03/13/2018 JOB ADDRESS: 3860 Moore ST EXPIRES: 03/13/2019 JOB DESCRIPTION: Residential Reroof Permit remove and install Tri -Built Rolled Modified Bitumen and Atlas Pinnacle StormMaster Class 4 Asphalt Shingles with redecking 27 total squares. (3 squares flat and 24 squares pitched). Pitch = 1/12, 4/12. Main roof and garage. *** CONTACTS *** OWNER (720)339-1104 WRIGHT KATHLEEN C SUB (303)296-1353 Randy Howard 020789 Colorado Exteriors, LLC *** PARCEL INFO *** ZONE CODE: UA / Unassigned USE: UA / Unassigned SUBDIVISION CODE: 2403 / APPLEWOOD VILLAGES, PROSPECT V BLOCK/LOT#: 0 / *** FEE SUMMARY *** ESTIMATED PROJECT VALUATION: 9,048.38 FEES Total Valuation 0.00 Use Tax 190.02 Permit Fee 204.30 ** TOTAL ** 394.32 *** COMMENTS *** *** CONDITIONS *** Midroof & Final Roof inspections for ROOFS 6/12 PITCH & OVER: 3rd party inspection will be required for both the midroof and final inspections. The 3rd party inspection report AND THE ORIGINAL PERMIT CARD needs to be dropped off to the Permit Desk at the City of Wheat Ridge. The report MUST BE SIGNED by the Homeowner. REGARDING ROOF VENTILATION: Roof ventilation shall comply with IBC Sec. 1203.2 or IRC Sec. R806. The installation of ridge venting requires the installation or existence of soffit venting. For calculation purposes, one hat or turtle vent equal to one-half of one square foot of opening. Effective December 1, 2014, asphalt shingle installations require an approved midroof inspection, conducted when 25-75 percent of the roof covering is installed, prior to final approval. Installation of roof sheathing (new or overlay) is required on the entire roof when spaced or board sheathing with ANY gap exceeding one half inch exists. Sheathing and mid -roofs may be called in at the same time, one hundred percent of the sheathing must be complete and 25-75 percent of the mid -roof may be complete. Asphalt shingles are required to be fastened to the roof deck with a minimum of 6 nails per shingle. Ice and water shield is required. Eave and rake metal is required. A ladder extending 3 feet above the roof eave and secured in place is required to be provided for all roof inspections. Roof ventilation is required to comply with applicable codes and/or manufacturer installation instructions, whichever is more stringent. In order to pass a final inspection of elastomeric or similar type roof coverings, a letter of inspection and approval from the manufacturer technical representative stating that "the application of the roof at (project address) has been applied in accordance with the installation instruction for (roof material brand name) roof covering" is required to be on site at the time of final inspection. F A1ar[ System Tel"I Hout 3113 Teller St. Wheat R CO SCOPE: Replace existing smoke detectors. Add new smoke detectors as indicated (6 total new). Replace heat detectors as indicated. Add one new heat detector to basement kitchen. Replace existing bells with horn/strobes. Add one new horn/strobe to basement. System Type: Conventional. Remote Supervising Station. NAC Circuits: Class B Style Y (16 gauge 4 conductor FPL, Tubed PVC jacket over insulated conductors) Notification Type: Temporal, Public Mode Initiating Devices: Class B Style A (16 gauge 4 conductor FPL, Tubed PVC jacket over insulated conductors) Wire is run exposed, at or above 7-6". Wire is secured every 4' and edge protection is provided 5024UD NAC 1 NAC 2 2nd Floor Devices Main Floor Devices Basement Devices Boilder Room Heat Horn Control Trol --fK§Q SYNC 15CD 15CD 15CD MOD + Typical Color Code Phone lines 1&2 AC Power System is monitored by Safe Systems UL listed Central Station Dedicated Branch Circuit For Fire Alarm r 0 0 RO 6 po j X e 0 , KAN \ hop '0 x') 0 0 X I o 0 0 , o � 4f 0; '601 6 4 0 01 0 O 0 00 ON oo 'oe <4 6 00 "s 00 \0 - 10 4 P ' " 0 P oo 6 , 6 �0 qp �e RCN o C; C; 'S C; 1 0 0 g. \'k, 1\11 IVO # # 0 0 ' pe 0 \ p VP v? Vs V-� VP 0 c /Ike Ike Sequence of Operations GENERAL NOTES: 1. All wiring to meet NFPA 70 Requirements 2. All control panel wiring will be secured to screw mounted anchor blocks or other solid structures within the enclosure. 3. Protect all control equipment from metal drilling and cutting debris. 4. Maintain seperate wire harnesses for input, output, and non power limited circuits, and maintain at least a 2" seperation of the "PLFA!'wiring from all other circuits. 5. Do not combine input signal cables in the same conduit with any other circuits. 6. All control panel wiring to be neatly harnessed, and run as horizontal or vertical routes only. 7. Stranded wire (if used) must be connected (at both ends) with clamping type terminals, crimp connectors, or spade lugs, 8. The 120 VAC control panel and fire alarm power supply panel power source must be from a principal breaker box, on an exclusively dedicated circuit. 9. Smoke detector heads are not to be installed prior to completion of interior site cleaning by all construction trades. 10. Prior to landing final terminations at the FACP, and after all devices are installed, all system wiring must be verified to be free of shorts, opens, and shorts to ground. 11. The fire alarm installation contractor to complete the NFPA72 "Record of Completion" prior to scheduling the AHJ acceptance test. 521OUD Battery Calculation Worksheet (all currents stated in mA) Device I Quantity of (Standby mAl Alarm mA Tot. Device I Tot. Device Description Devices Per Device L Per Device iStandby m4 Alarm mA Main Circuit Board 1 100 170 100 170 170 1 100 1 170 Auxilliary Devices (list ail A B C D E IF G H K L M N Smoke Detectors • Sync Module I 1 16 2 Heat Detectors - ---- ----- • • 1 - Auxilliary Device Totals 0 • Min. AM Battery Required 3 Pull Stations - 0 1 • 3.00 • • 7.00 4; 4� V) T DEVICE 5 MOUNTING HEIGHTS n O 6 U LC) 0 0 (1) - F- < 4— 81 (1) - ----- 0 101 < > ::- 0 11 12 i Fire alarm AC power failure 0 0 _ -- --------- 0 - - ---- --------- - 131 Fire alarm system low battery • 114! Power S AC power failure Wy • • • 15 Power Supply low battery 16 it 1 • • • - 0 ----------- — • 0 17 Ground Fault 0 0 1 0 18 Notification appliance circuit short fi • ---------- • j- ------- 1 C A B I D E F G I J 1 K L M N 1 0 Sequence of Operations GENERAL NOTES: 1. All wiring to meet NFPA 70 Requirements 2. All control panel wiring will be secured to screw mounted anchor blocks or other solid structures within the enclosure. 3. Protect all control equipment from metal drilling and cutting debris. 4. Maintain seperate wire harnesses for input, output, and non power limited circuits, and maintain at least a 2" seperation of the "PLFA!'wiring from all other circuits. 5. Do not combine input signal cables in the same conduit with any other circuits. 6. All control panel wiring to be neatly harnessed, and run as horizontal or vertical routes only. 7. Stranded wire (if used) must be connected (at both ends) with clamping type terminals, crimp connectors, or spade lugs, 8. The 120 VAC control panel and fire alarm power supply panel power source must be from a principal breaker box, on an exclusively dedicated circuit. 9. Smoke detector heads are not to be installed prior to completion of interior site cleaning by all construction trades. 10. Prior to landing final terminations at the FACP, and after all devices are installed, all system wiring must be verified to be free of shorts, opens, and shorts to ground. 11. The fire alarm installation contractor to complete the NFPA72 "Record of Completion" prior to scheduling the AHJ acceptance test. 521OUD Battery Calculation Worksheet (all currents stated in mA) Device I Quantity of (Standby mAl Alarm mA Tot. Device I Tot. Device Description Devices Per Device L Per Device iStandby m4 Alarm mA Main Circuit Board 1 100 170 100 170 170 1 100 1 170 Auxilliary Devices (list ail W M 0 Photoelectric Smoke Detector 20= 012 0.12 2.4 2.4 1 Sync Module 0 1 16 16 0 0 Auxilliary Device Totals 20 Min. AM Battery Required 2.50 2.4 L 2.4 Notification Appliances (list aig W M 0 15CD Horn/Strobe 3 N/A 106 N/A 318 Notification Appliance Totals 3 Total System StandbyAtH 2,46 N/A 318 Summa Section W M 0 Standbyl-Irs. Required 24 Alarm Sounding Minutes 5 Total System Standby n-A 102.4 Total System Alarm mA 490.4 Total System StandbyAtH 2,46 Total System Alarm AM 0.04 Min. AM Battery Required 2.50 Recomm A/H Battery 3.00 ISupplied AIH Battery 7.00 ( -- 4 " - 4" MIN.—I Ne ver h here P 4" MIN. Detector 6" MIN, acceptable here 0 P ❑ 96" MAX. P 80" MIN. 54" MAX. 42" MIN. I Top of detector acceptable here 12" MAX. FINISHED FLOOR V) — , Z 0 W M 0 0 , S� V) 1 0 1 � 0 V5 Z Z I V) Z -,=> � Z 0 - 0 UJ Z M Z W M M 0 0 0 l_- < N') co 4� V) 0 DEVICE :3 0 MOUNTING HEIGHTS Replace Exist Heat Detector T F Replace Exis E P (�F Replace Existing Heat Detector Replace (.pa F". 8.11 R ace Existing egL P ReptExistin P 11, 'N I [, - (5.08 Ohms per 1000') Withbi Range Wire length is measured in 1 direction. The formula used is: (Wire length * 2 / 1000) * Resistance Total Current Per NFPA72 - System to function at 85% of primary voltage (85% of 24V = 20.4v) Gentex Devices Listed for 16V - 24V Operation. 20AV - 16V = 4AV drop allowed. BUILDING CODE SUMMARY Occupancy Group: Group R-4 Number of Stories: 2 Non-Sprinklered 2003 IFC 2003 IBC DRA WING PREPARED BY Damon Sickmon, C.E.T. NICET Level III - Fire Alarm Systems Cert. No. 103403 - Exp. 07/07 SAFE SYSTEMS, INC. 3640 Walnut Boulder, Colorado 80301 Telephone: (303) 444-1191 THIS DOCUMENT IS THE PROPERTY OF SAFE SYSTEMS, INC. LOANED TO RECIPIENT IN STRICT CONFIDENCE AND SHALL NOT, WITHOUT PRIOR WRITTEN PERMISSION, BE DISCLOSED, REPRODUCED, COPIED OR LOANED, IN WHOLE OR PART, OR USED FOR ANY PURPOSE OTHER THAN THAT FOR WHICH IT WAS INTENDED. ACCEPTANCE OF THIS DOCUMENT WILL BE CONSTRUED AS AN AGREEMENT WITH RECIPIENT TO THE FOREGOING CONDITIONS. ��l 0 Is 'T PLANS MUST REMAIN ONSITE DURING CONSTRUCTION CONDITIONAL APPROVAL -.-. Plan reel) ouglas J C1 Plant ;a ire -ode-Fire Insp9d90. Saba Stat gftftW,5i r e l 8 u qprasti6e Inspector late: State Certified Fire Suppression Inspector Date: lomm nts: Comments: LEGEND 0 M< P E P Fr7CP EOL Horn/strobe Heat Detector Smoke Detector Pull Station Fire Alarm Control Panel End Of Line Resistor Gentex GEC Cherntronics, System Sensor 2400 Existing Firelite 5024 Firelite Resistor C.fl THIS DOCUMENT IS THE PROPERTY OF SAFE SYSTEMS, INC. LOANED TO RECIPIENT IN STRICT CONFIDENCE AND SHALL NOT, WITHOUT PRIOR WRITTEN PERMISSION, BE DISCLOSED, REPRODUCED, COPIED OR LOANED, IN WHOLE OR PART, OR USED FOR ANY PURPOSE OTHER THAN THAT FOR WHICH IT WAS INTENDED. ACCEPTANCE OF THIS DOCUMENT WILL BE CONSTRUED AS AN AGREEMENT WITH RECIPIENT TO THE FOREGOING CONDITIONS. ��l 0 Is 'T PLANS MUST REMAIN ONSITE DURING CONSTRUCTION CONDITIONAL APPROVAL -.-. Plan reel) ouglas J C1 Plant ;a ire -ode-Fire Insp9d90. Saba Stat gftftW,5i r e l 8 u qprasti6e Inspector late: State Certified Fire Suppression Inspector Date: lomm nts: Comments: Drop Calculations Notification Circuits 5024UD NAC 1 Used For Horn Control CD 0 C.fl - 0 0 0 0 l_- < N') co 4� V) 0 :3 0 0 n O U LC) 0 0 (1) - F- < cf) (1) 0 < > ::- 0 0 -+� :t-- 7' Cn 3: n E Q) < M Ct 0 0 D Drop Calculations Notification Circuits 5024UD NAC 1 Used For Horn Control CD C.fl L 0 0 l_- < N') 1-- < (JJ O LC) 0 0 > ::- 0 0 -+� :t-- 7' Cn 3: n E C) < Ct 0 < (J� 0 < :7 0 DWG NO. FA - Drop Calculations Notification Circuits 5024UD NAC 1 Used For Horn Control O N o w =r N 7 W n A p ~ mm W n W ~ ' O M cn ~ N < N Q N (D 7 N n m ~ d 0 ~ ~ ~ N ~ CD C) 0 3 ~ i L. 0 c ~ G a ~ N N A n Q 0 ~ C O CD Z ~ 0 (D w 3 ~ 0 o v r*~cnm 0' W (D < Z3 m ZNN~ 0 om z N• ~ (D ov ~ m ~ ~ City of Wheat Ridge Building Division TO: Ellen Knapp FROM: Chad Root, CBO SUBJECT: 3113 Teller DATE: 4-18-07 The only items left are the two egress windows and the stairs on the outside of the building. Other than that you are finished up. Hope all is well take care. Sincerely,. Cha xoot Of ''Vheat Ridge ~ Nseoftneou,s :PERA'IIT - 070160 , F812MST NO: ' 07610 TSSUED6 03/OS/2007 J0t :ADDRk83: 3113 3aL$R $'S . EXBIRBS: 09I01I2007 ' . . DE6CI2YPTI0N: cdde vic+ZaCion carrectiana gexChad Root - per Notice & Ordez ge 30/9i5~~1157 C2H t)ffiSTGN 07-0035 $VE343/4~514j~S ~jlI[e Yjippin -02-0574M& M 818etsic ConneCtion InC• 9LTB 3d3/U1-1711 . 02-0331Western Statee Mechanical Ihc:.f tbDE: ttA V58: uA TVIS1t'fH:: UJL.'; .BLOCKILOT#: 0/ ggg , : 19SfiIMAm PItOS$CT VALUATSON: 19150:00 PerluiC Fee! 417.70 Teatal Valuatian .00 Tax 355.50 a~ !TOTAL 773.20 . t 00 Per `Nb'TI4`E Aw `0*4..attached cagy subjaet tc64i°d' ikispdbtican Sub-contracta7r~ mxA I uC be currently licezssed in Wheat ttidge before any work is pcr€vstnect. I hr,Ymby exktt+Cy tkMC 7ietb0C7k.d195.anceapzop4se3 py thia pexmlt appllcation areaccurate, aad do not violate applicaUle @YtYLnanCe4, tuld,e;o# 4g~Xit19M8 dL„Cttd CiEy,oE Nhaat Rkdge or sovrnante, eaeements ar.reeknGtldne of record;that.all ' measuYetnenGa ph0eu,xa'Ad,#l1eq8Ci606_PIABe arp. aeewCats; that I have raa8 pnd agzee to abide by all caraiitione prinCedon ehis. . apglSCatloh ~ tcSCiwie „,Ypatfa#lfility for:COdg+lipnce aith ehewheat Ridge eui163ng Cok1a.(I.e.C)and aFlother applYeabi4 tlsii '~ar }ror)t un9et thia~pkz*dt.: Plazne suti}ect -to fie18 inepection.., i;'.. . . . . . . F 61 CVYp bf c16wneT 'Cate ' . . . . 'Ymie pCmiC.7r4~jjsa~'.Sf} secqt9exlCe wlth the pYOViel.aps ept Porth inyour application and ie eWbject CO trie lawe,oEthe . State aE C:dlotks46404 Go Ch4 SdidiY#s iegv3atioas aTM esiilding Codee of wneat xlage, Colorada or aay othef appliceble. . drIIfPas~ces oS .el~C'i~y.~ „ . , . . . . . . . . . . . 2. '$t0 pd'Y~* ' k,-..ik15}3 CJQiItta19g d9~F fx7ap tt+eSeMm AaCe_.'Requette:for an exteneian muet be raceived prior to. expiration dat2. An,pt[GGtqi,SUt,Ctlyy4e,gxA,S~ws~d8t'thR.dS6CittSOnof t1fe19ui1dicgOfficiAl.. . 3. If th30 PR'LMLt`¢f[pl,cApi, a t~w pki~VSC may De aGgulredl!Gr n teeoE one-halfthe amount normally XeqU1Yed.psovlded noChaGpell haW SSdan 6Y,.NI#.3 be msde in Che~.oriq}na1 pYane enflepecificatione and any euepenaion aYabandql1elent hae not. wcCesdtld wie (3k ysicY,,.Tf chin$es ha^re been or if.euspenaion oz.a0andonment exceeda one (1) year, full #eea ahall . lie pHiG t61'.3 Mo9' pb1mtL. ~ . . . . . . . q. tio wYk o€ asky` Wi7nei YEYbIl 1Yt` ftSit that wili ChaNgd.tha aatqral flovofwater caueing a dtainage px'oblen.. . . . ,5.: ContxaCtur ;phaIu~ npk4fy! C,wffiw4Iding IadpectoY tventy-taur (24)hoqzd in advance Eor all ineBecCfona aM. s1w11 receive . writCeir appiOvnl~o1~ YnHPactiatli CaY6 befose pttlceeding.with.sutctiesSVeB~eee oE the job. (.6. K~he leguenca o{ a peliniit or the~appYWaloY CYawlnga,and epeciFicatione etwll not be cona[rued to be a yexmit far,dor, . an apyXOVay~,Ox, Af+7[ 4" i4+1 ?t the oi the building codeeorany other ortllnance;law, ruleor regul8tion. . ..Ail Plan xeuler da . C?-' i0. . . . . . . . . . . - ` , r;.. i . . . . . _ Bipnaturb of Chie ildlng pfticai:: . . date: . . . . . t$00VT=9 ;gi I *y y1Iti4' 13031234-5933 ~HUIL➢ING OFFICB: (303) 235-2Y355 Rgt~t,1ES'Tg MCfg!1' kyE~AD$ $Y 3PM ANY BUSINESS DAY FOR INSPECTION THS FOLLOWSNG BU8INESS DAY. F WHEqT o ,p = ~ m c~~ORPpO CItY Of WIl@8t RICIgB Building Permit Number. 6 f70160 Community Development Departrnent oace: ~~GLE AND TWO-FAMILY .,F:12 CHILD.U V[.S PERA'~'~kIT Property Address: Contractor License No.: OWNERlCONTRACTOR SIGNA7URE OF UNDERSTANDING AND AGREEMENT I Buildinp Dept. Valuafion Figure: $ I hereby ceRify that the setback distances proposed by this permit application are accurate, and do nof violate applicable ordinances, rules or regulations of the City of W heat Ridge or covenants, easements or restrictions of record; that all measurements shown, and aliegations made are accurate; that I have read and agree to abide by all conditions prinfed on this application and that I assume full responsibility for compliance with the W heat Ridge Building Code (I.B.C) and all other applicable Wheat Ridge Ordinances, for work under this permit. Plans subject to field inspectlon. (OWNER)(CONTRACTOR): SIGNEO. DATE (OWNER)(CONTRACTOft):PRINTED DATE V 21U0: $ Permit Fee:$ Plan Review Fee:$ e aac: Total:$ Use of Space (description): -L / y ~ ~ Description of work: U/A~f 1`~}''~ Sq. Ft. added nQ-K(x„ I (Ymr . COMMENTS: Approval: Zoning: COMMENTS:' Approval: WORKS COMMENTS: Approval: DEPARTMENT COMMENTS: Approval: BUILDING DEPARTMENT USE ONLY SIC: Walls: Roof: Stories: Residential Units: Electrical Lic nse No: Plumbing License No: Mechanical License No: Company:~~ Company: Company: C~o,~l,t/ Expiration Date: Expiration Date: Expiration Date: Approval: Approval: Approval: (1) This permit was issued in accordance with the provisions set forth in your application and is subjed to the laws ofthe State of Cobrado andto {heZoning Regulations and Building Codes of Wheat Ridge, Colorado or any olher applicable ordinances of the City. (2) This permit shall expire if (A) the work authorized is not commenced within sixty (60) days from issue date or (B) the building aufhorized is suspended or abandoned for a period of 180 days. (3) If this permit expires, a new permit may be acquired for a fee of one-half the amount normally required, provided no changes have been orwill be made in the original plans and specifications and any suspension or abandonmenl has not exceeded one (1)yeac Ifchangeshavebeenorifsuspensionorabandonmentexceedsone(1)year,fullteesshallbepaidforanewpermit. (4) No work of any manner shall be done that will change the natural flow of water causing a drainage problem. (5) Contractor shall notify the Building Inspecfor twenty-four (24) hours in advance for all inspections and shall receive written approval on inspection card before proceeding with successive phases of the job. (6) - The issuance of a permit or the approval of drewings. and specifcations shall not be construed to be a permit f.or, nor an approval of, any violation of lhe provisions ofthe building codes or any other ordinance, law, rule or regulation. All plan review is subject tofield inspections. Chief Building Official Company: Phone: ~l« -7,l,57 F WHEAT O P ~ o - ~ ~~[ORA~O NOTICE AND ORDER To PROPERTY OWNER AND ALL CURRENT OCCUPANTS January 3, 2007 Pursuant to the 1997 Edition of the Uniform Code for the Abatement of Dangerous Buildings, the 1997 Uniform Housing Code and the 2003 International Property Maintenance Code, the following property is in violation: Property Description: 064800 Barths. Block 1, Key OOH, Section 26, Township 3, Range 69, SE quarter section or commonly known as: 3113 Teller Street. Wheat Ridge Colorado 80033. According to County Records you are the property owner of the described property. Property Owner: Attn: Temenos Elder Caze Company 3113 Teller Street Wheat Ridge CO 80033 Charles and Ellen Knapp 3050 15th Street Boulder Colorado 80304 All Current Occupants of 3113 Teller Street Wheat Ridge CO 80033 NOTICE The property owner, and all current occupants, are hereby notified that the undersigned Building Official of Wheat Ridge, Colorado, has found the building located on the above described real property to be a Dangerous Building within the meaning of Section 302 of the Uniform Code for the Abatement of Dangerous Buildings and Section 1001 of the Uniform Housing Code both of the 1997 edition, as adopted by the City of Wheat Ridge, Colorado ("Code"), as more particularly set out below. The following is the list of items making the Building Dangerous and which shall be fixed to meet applicable codes: 1. Bedroom windows do not meet egress requirements of the Uniform Building Code or the Intemational Building Code as required in Section R310. 2. Minimum required width on the stairway does not meet code according to section R311.5.1. 3. No Building Permit was pulled for electrical work 4. Boiler room needs make up air for combustion 5. Hot water shall not be hotter than 140 degrees this could scald a person if over 140 degrees. 6. GFCI needed in all bathrooms and kitchen outlets. 7. All exhaust fans must be vent to the outside and need to be working. 8. Ceiling of porch is sagging and is ready to fall down on occupants. Needs work to meet a 301b snow load. Add 2x4 as stated in several locations to support structure. 9. Several up stairs bedrooms do not have egress windows shall have 5.7 sq. ft. of open able space per code. Min of 20" opening. Cunent opening is only 19". 10. Need handrail on stairways. 11. Bedrooms in basement shal] have egress windows along with living space. On or before February 12, 2007, bedroom egress windows shall be done or the owner shall have the tenant removed from basement. 12. Dryer vent is not to code must be metal duct behind walls and ceilings. 13. Exterior stairs are not to code and are considered to be dangerous no rise shall be greater than 8" and a flight of stairs shall not exceed 12 feet in height without a landing. 14. No handrail to code on exterior stairs. 15. Stairs in basement do not meet code with no more than 3/8" difference between treads on a flight of stairs. 16. Chair lift does not meet code. Must remove chair lift. By February 12, 2007 as stated in conversation of January 8, 2007. This is a]ife safety issue; Code states minimum is 36" width. ORDER The City oF Wheat Ridge Building Official has determined the building referenced above to be a Dangerous Building. The owners are ordered to pull a building permit to fix the deflicient items. If the deficient items are not fixed by February 12, 2007 or such later date as permitted by the Building Official, the Building Official will take steps under the Uniform Code for the Abatement of Dangerous Buildings to prevent occupancy after March 30, 2007 by posting the property to prevent occupancy and acting to remove all occupants from the building. APPEAL OF THIS NOTICE AND ORDER Any person having record tifle or other legal interest in the above described premises may appeal this Notice and Order or any action of the Building Official to the Building Code Advisory Board ar known as the Board of Appeals pursuant to section 112 of the Code, provided that the appeal is made in writing as provided in the Code and filed with the Building Official within ten (10) days from the date of service of this NoCice and Order. Failure to appeal will constitute a waiver oF all rights to an administrative hearing and determination of this matter. FILING OF AN APPEAL SHALL NOT STAY THE EFFECTIVENESS OF THIS NOTICE AND ORDER. It is a misdemeanor to occupy this building after March 30, 2007 or to remove or deface this notice. BY ORDER OF THE CITY OF WHEAT RIDGE'S BUILDING OFFICIAL 303-235-2853 303-570-7510 Chadley Root, Building Official ~Tty r~f~heat Ridge R~l Eleetric PERNtTT - 074041 PIsRmit N4: ~070001.;~ ~ ISSVBD: 01/03/2007 . . . JO8`ACIDRErSn 3113 Wii~ ST BXPIRSS; DE3CR2f'TTbN~: vaTibttffi eleatYical vforkon GFI's~ and outlets gc JA3/'757~4943 ChtsteY A. Gebhards 07-0001 C&J Eledtric nwner 303f233-2,408,,131ax1 34naPP PAR"ti tolr0 ZONE CN3Ds: VA . . USE:. . VA SUHbii!T3T6N': VA` BLOCK/L6T#r '0/ *x ggt'S~ ESTTMATED PROJSCT VALUATION: 300.00{ , ; . . . F8&S , . . ~ Perecat f'Ce ~ 91.65 ToGal> *Xttatisui - . . . . .00 use Tatc 5.90 TOTAF. 97.05 . . . . . . Corcaiien Eo i Must tltioet.,,~405 mG Sub7ecC ~a -fsett lrispepC}on ~ Permit E`84s' trip~:etl' duato work being darte without a pezmit Ihereby oRXCify CriaE tht;e~th3'ak d1aCancee prqpoaedby thie pea~niY,application aze acaUYate, 3nd 77d nok ViolBte appllCable ordinaklCea, rulem or negklnt3GMl$ a8'.the G'Sky oE Wheat BSdge or covenan[e, eaeemMte o; reeCY3Ctlbne.of tecotd:.ChbR d11 meaeuc4taei2ts aAown, .6std,3Alegebi64a; N~ade bre accurate; tHaC I krave repd and aysCa to abid'e bg edl cCridSt'foha prtnted on thie appl}f~Gga~py1q~y qnd th,yT~ Y"Rl61xaE ~,tt11~ iRbpois8lhility ior c8mpliance wikh the Nhent RSdge Bui181xg Code ~(I.B.C) as~d all pCh~- . 'dge ~1YAlaWmdsr for wcrk unfler thie pezml/t. F1anb.euDjeet to fiald inepeetiort. ~i appl: e---~~ sigriat e of epntraceazltlwn+ez. 'date . LThie.gq%~Nmt wae itlYlii~#;f,n~;4c~ftPee witri'.Che prwieione eet forkh Sn }roui application an6 ie aukijeet to the Saws a€ Cric Stat1 OS SQlarado ari8-@o kEle 2qniiig Blgulatione and Bvilding Codee of Wheat Ridge, Colorada oi.aiiy othez app2icebYe ord4vnffCee of'tM CS~y'.: , . . . . . . . 2. 1'his peE1fi73i~tRk#11'bilpd~q, LL {A) the Work huthorize&Se not commanGed wiehin 91xty (60) deye Erbm iesae datb-or Yhe. bui;dic(gatFEtinYbsed ia,~aubpleFU99dor abyt+doned for a.peripd of 169 daye. 3.. if kh}q pps~apt eXpstktl; a Y~v nit may.be acquiredfor a Eee of one-half the amovAt nos5nakly requizett. DYa'+ided no.: efiangee hane Leen dr a9.11't!p t~8r in Cheoxlginal plane and epeci€ication¢ atta any svepehelCn ox~ab6nddfAsan2 hes ncC. ..nvccepd~ psis (1} St Ct,l$~{glfe have Leen or if auapeneion otabanfloMient excelCS:one iiy yeaY, fuYY frtra eLall . . be p0:id ~oT'm Ma jfet~N}iC•. , . . . : . ; 4. No wRZk 6f ptiy ~'eY sMa1I be dme Chat wi12 change the natural€lov of water causing a diainago.plrolsledq. ~5.:. CoctEYaeEoT Ahall noC1Ex tlfe 9ei$Sding Inapector twenty-fwr (24)houre in.advance Eor all inepectibne ari+1 &Iwll zene3ve-.vrritten AppYOVaI, On iisBpertioti c8t9 befate proceeding with eucceeaive phaeee of the job. . 6: Th4 i0nWenc2 0€ a pexin4U ox the .}pprSS?rval ofdrawings and sgecifieatione ekialZ not De construed [q bC a gBTinYt Eor, nor...a}t gpprav3~~af, any vi¢lai:lq¢1 ofthe provieione of the bkilldingcodea orany oCkfer ozdinatlet, lavri rule or.segulation: Ali plan aeview SY bW?I UeXd #vt . . . . . 319natuz8 CP Chitf 9u d ` . date . . . . . . . . . . Z2i9pgC".1'~ ftEpppg~~.~t,~~ Ei ~~',44-5933 BUILDING OFFICE: (303)239-2855 . . REQTJ$STS MUST 9 F6 MADE S~Y 37t~SP.BUSINES9 DAY FOR'INSPECTION THSFOT+LOWING BU'STNBSS DAY.. . COMMUNITY DEVELOPMENT DEPARTMENT Building Permit Number: oE w"EqrP gUILDING INSPECTION LINE - 303-234-5933 Date: ~ o CITY OF WHEAT RIDGE 7500 WEST 29TH AVENUE I~LAN # WHEAT RIDGE, CO 80033 - (303-235-2855) MINoR APPLreATraN Property Owner: Property Address: 3) I3 T e~~pr 5+, Phone: 3 CJ Conhacfor License No.: 4 9 Company: L` 4 S ECFCT OZ I~ Phone: 3 0 5-1 v ^ 3~7 rj OWNER/CONTRACTOR SIGNATURE OF UNDERSTANDING AND AGREEMENT guildina Dept. Valuation Figure: I hereby certify that the setback distances proposed by this permit application are accurale, and do not violate applicable ordinances, rules or regulations of the City of Wheat Ridge or covenants, easements or restrictions of record; Ihat all measurements shown, and allegations made are accurate; that I have read and agree to abide by all conditions printed on this application and that I assume full responsibilily for compliance with the W heat Ridge Building Code (I.B.C) and all other applicable W heat Ridge Ordinances, for work under lhis permit. Plans subject to field inspection. (O W NER~(CONTRAGTOR): ~ Value:$ Permit Fee:$ Plan Review Fee:$ Use Tax: TOt31:$ Use of Space (description): / Description of work: SS~cS 6 /:/y 64 IIEPnSr(j P~E?CTY'~ ~K+" C46i /aS,pe:'Gf/~~, ccrrc-cf~c-~ / peV^f~a~H-. C.~ il_'~~~,:;y., - Sq. Ft. added ~ Y` BUILDING DEPARTMENT USE ONLY SIC: Sq.Ft.: ONING COMMENTS: Approval: Zoning: Approval: WORKS COMMENTS: Approval: DEPARTMENT COMMENTS: Approval: Walls: Roof: Stories: Residential Units: Electrical License No: Plumbing License No: Mechanical License No: Company: Company: Company: Expiration Date: Expiration Date: Expiration Date: Approval Approval: Approval: (1) This permi[ was issued in accordance with the provisions sel forth in your application and is subject to the laws of the State of Colorado and to the Zoning Regulations and Building Codes of W heat Ridge, Colorado or any other applicable ordinances of the City. (2) This permit shall expire if (A) the work authorized is not commenced within sixty (60) days from issue date or (B) the building authorized is suspended or abandoned for a period of 180 days. (3) If this permit expires, a new permit may be acquired for a fee of one-half the amount normally required, provided no changes have been or will be made in the original plans and specifications and any suspension or abandonment has not exceeded one (1) year. If changes have been or if suspension or abandonment exceeds one (1) year, full fees shall be paid for a new permit. (4) No work of any manner shall be done that will change the natural flow of water causing a drainage problem. (5) Contrector shall noti(y the Building Inspector hventy-four (24) hours in advance for all inspections and shall receive written approval on inspection card before proceeding with successive phases of the job. (6) The issuance of a permit or the approval of drawings and specifications shall not be construed to be a permit for, nor an approval of, any violation of the provisions of the building codes or any other ordinance, law, mle or regulation. All plan review is subject to field inspections. Chief Building Official STOP WORK ORDER YOU ARE HEREBY ORDERED TO STOP WORK LOCATED AT ~ ~ ~ / , - ' ! , % , , . BY ORDER OF 'PHE CITY OF WHEAT RIDGE BUlLD1NG DEPARTMENI' FOR THE FOLLOWING REASON(S): } ~ ~ G / L---IeL: f!~ x~ ~ ~ This ❑otice may be removed ONLY by THF CITY OF WHEAT ftIDGE BUILDING DEPARTMENT ! Date: ~ ~ ~ ~ Buildiog inspector un °b 1 N1 ~ HEALTH FACILITIES AND EMERGENCY MEDICAL SERVICES DIVISION 4300 Cherry Creek Drive South Denver, CO 80246 Voice; 303-602-2800 Fax: 303-753-6214 www.odphe.stiLic.e*,wlhf/hfd.wp State Licenstue Program Assisted Living Residences Form: Sign off for Local Authorities 6 2007 ZONING DEPARTMENT 0ppep10ipublicHeaM&Em1 ~lF&EMSD written evidence of compliance with local zoning codes and ordinances must he obtained Conti vt e or Return thi departments in your area and have the director or designee sign below or otherwise indicate app form, signed by the proper authorities, to complete your license application. A final inspection cannot be conducted until these approvals are obtained A license cannot be Issued until the completed form, with the original signature, is on file with the Division. Name of Facility: 7"RmRr,os 6/cLr CrYe ~o~ .r e. '"r-~1/ r (•.Lrn..-i. LJ .c~' R/B-,BQ JeffiyYs Ur (~a aooa No. of Licensed Beds Requested: _.g l/ Cfd7rir.o2 SL )/t Phone: 3L9 Fax: Name of Person to Contact: ' ;ZZo Z76 07;L;4 Zoning Department having Jurisdiction: L.t" kl d The above-named facility meets the requirements for caning approval: [X] YES [ ] NO If "no" please explain on a separate attachment. Date: J _(f }2 ~Ct f ~r Z CLU Signature: ~~77 Name of Person to Contact Yc t ICS phone: 60s--E- -29 : C✓~ Address: C' _ o... Iul~ o 1 , I" /fvC_t,~v [ ] Application for a new license i [ ~Shange of Ownership Change effective: [ ] Granting of a License Effective: v [ ] New secured unit [ ] Name Change Change effective: [ ] increase/Decrease of Beds Change effective: From: to:-~--- ] Action taken against the License Effective: [ ] Facility Closure Effective: ] Jt; f,4- A C.9t.nt_ , ei' p'v 4 Initial Notification to Zoning Dept, date: by: - Final Notification to Zoning Dept date' by: t~ b0/60 39Vd 9NINNVId 198Z9EZE06 EZ:60 L00Z/92/90 41C 0 00 ~f 0 HEALTH FACILITIES AND FMEnCENCY 6' MEDICAL SERVICES DIVISION State Lieensure Program 4300 Cherry Credo Drive South 4130,7 Dmvar. CO 80246 Assisted Living ResidenceVoice: 303-692.28Uo Fax: 303-0536214 ~ www.cdphe.state,co.us/hflhfd.asp aadFavilvDroeot Form: Sign off for Local Authorities BUILDING DEPARTMENT Written evidence of compliance with local building codes must be obtained Contact the city or county departments in your area and have the director or designee sign below op otherwise indicate approval. Return this form, signed by the proper authorities, to complete your license application. A final inspection cannot be conducted until these approvals are obtained A license cannot be issued until the completed form, with the original signature, is on file with the Division. Name of Facility: T't' 3 r+e n~ of k-Y AAAI aa• 3113 - ehey- Je rsan co ,3003'3 No. of Licensed Beds Requested: i v Phone: : 9,S313" Fax; Name of Person to Contact: V rt rte: S'- 7ao~ 07aef L~ Building Department having Jurisdiction:, c:.11,e~t R' The above me a Ity eet the requirements for building approval: >0 YES [ } NO If "no" pleas expl ' On a e to at Date: Name of Person to Contact: phone: fro-max: L~ Address:_, _ OFFICE USE ONLYw OFFICE USE ONLY- OFFICE USE ONLY--OF'F'ICE USE ONLY [ ] Application for a new license [ yj 'Change of Ownership Change effective: [ ] Granting of a License Effective: 5e/Co [ ] New secured unit b0/Z0 39t1d [ ] Name Change Change effective: ] Increase!De cease of Beds Change effective: From:- to: [ ] Action taken against the License Effective: [ ] Facility Closure Effective' 2fin iti al Notieation to zoning Dept, date: byal Notification to Zoom De t date: D b 47 9NINNV-1d LSBZ96Z£0£ £Z:60 L00Z/9t/90 HEALTH FACILITIES AND EMERGENCY MEDICAL SERVICES DIVISION State Licensure program 4300 Cherry Creek Drive Sou h Denver, Co 80246 Assisted Living Residences voice: 303-692-2800 Pax: 303453.6214 www.cdphe.st%w.co.usihf/h fd-asp Form: Sign off for Local Authorities FIRE DEPARTMENT ~'9y `'<G ~_°oQ,, 200) Written evidence of compliance with local fire codes must be obtained Contact the city or county departments in your area and have the director or designee sign below or otherwise indicate approval Return this form, signed by the proper autharhies, to complete your license applicaijem A final inspection cannot be conducted umdl these approvals are obtained A license cannot be issued until the completed form, with the original signature, is on file with the Division. Name of Facility: Te m» ) I o s 6-14y, Cu fv, C~ rr. n .3/13 '7-ells,- Sire, No. of Licensed Beds Requested: ~ :r & Phone: .'303 qd~3 i3 Fax: Name of Person to Contact: Vl k-ivyi ne, s v 7 gGs 4 4 Fire Department having Jurisdiction: 1,3),ee i` k'rcp The above-named facility meets the requirements for fire safety. [ ?(YES [ ] NO If„no„ pleaseexi'tar eparata Qhmeut or . the Comments section, below. Name of Person to Contact; _ ! /v cry ~aLG' Address:_ !Lpa/ z""ed- CODE(S) APPS iED AND EDITION: OFFICE USE ONLY- OFFICE LISE ONLY-- [ ] Application for a new license F4 Change of ownership [ ] Granting of a License Cfg2Fax: To3 T y~/r Phone: Change effective: Effective: I ] New secured unit ] Name Change Change effective: [ Increase/DecreaseofBeds Change effective: From:- ~-~to:_. [ ] Action taken against the License Effective: [ ] Facility Closure Effective: [ ] Initial Notification to Zoning Dept. date [ Final Notification to Zoning Dept date:- b0/b0 39Vd 9NINNtl-ld by: L98ZGEZ60C 62:60 L00691/90 C ; z m m ; o y D • m ; 4! A O Z ~ y 0 t c C CO) :(7 m A . m K m D 0 ((D ~ ~ o U) Afr 0 D iB ri f2_ Z a ei a t5 N . m tiJ~t6 co 0- > n ( ' o ::7 cr ca ` m 0 sj W 1 ~~3 m C G ~ N T _ • m» z C c) Z p m ° C') a 1 \ Q W H L v~ O 0 0 0 :v v Ki 2 J Do ~o 6 m J) S M 0 = r o W M CD ~ a w ,p c. z tg m r m E a i .a RI w m m v Hasler € sn^„ N C1 a ca ru ~j d+3 :1 ~`v iv co e ro W HEALTH FACILITIES AND EMERGENCY MEDICAL SERVICES DIVISION 4300 Cherry Creek Drive South State Licenstue Program Denver, CO 80246 Assisted Living Residences Voice: 303-692-2800 Fax: 303-753-6214 www.cdphe.state.co.us/hf/hfd.asp Form: Sign off for Local Authorities BUILDING DEPARTMENT Written evidence of compliance with local building codes must be obtained Contact the city or county departments in your area and have the director or designee sign below or otherwise indicate approval Return this form, signed by the proper authorities, to complete your license application. A final inspection cannot be conducted until these approvals are obtained A license cannot be issued until the completed form, with the original signature, is on file with the Division. Name of Facility: 7--e kne nexs EI cbt Ox re Ct arL424 y Address: 3113 7~%lp t S-k--Au iJ &I Qn) Ri d W Je4 4 rSGn co 5-003 z City County No. of Licensed Beds Requested: Name of Person to Contact: yI C-1Ld r; rta- -.St-p-t Phone: (30319S-3 l 349 Fax: ' Building Department having Jurisdiction: CJAeAf Ri p 7a0 aR607aq- The above-na I ity eels the requirements for building approval: YES [ ] NO If "no" pleas expl i on a e to attachment. Name of Person to Contact: . ,K,itt2 Phone: (3 ly' 7 gax: Address: USE ONLY-- OFFICE USE ONLY-- OFFICE USE ONLY--OFFICE USE [ ] Application for a new license [ ] Change of Ownership [ ] Granting of a License [ ] New secured unit [ ] Name Change [ ] Increase/Decrease of Beds From: to: [ ] Action taken against the License Effective: [ ) Facility Closure Effective: [ ] Initial Notification to Zoning Dept. date: _by: Change effective: Effective: Change effective: Change effective: Final Notification to Zoning Dept date: HEALTH FACILITIES AND EMERGENCY MEDICAL SERVICES DIVISION 4300 Cherry Creek Drive South Denver, CO 80246 Voice: 303-692-2800 Fax: 303-753-6214 www. cdphe.State. co.us/hf/hfd.asp State Licensure Program Assisted Living Residences Form: Sign off for Local Authorities ZONING DEPARTMENT Written evidence of compliance with local zoning codes and ordinances must be obtained Contact the city or county departments in your area and have the director or designee sign below or otherwise indicate approval. Return this form, signed by theproper authorities, to complete your license application. A final inspection cannot be conducted until these approvals are obtained A license cannot be issued until the completed form, with the original signature, is on file with the Division. Name of Facility: T"Pare)~ os Elkv, Gtfe Ca~Y~pa~Y 3/13 'TeIIPY ONLY-- OFFICE USE ONLY No. of Licensed Beds Requested: 8 Name of Person to Contact: V C~ d~ /rte .SV pi -&Phone: 3Q 31 9 Fax: ( ~ Zoning Department having Jurisdiction: 1n1~ e at Rlc.~ ;7Ao Q96 6;72-V The above-named facility meets the requirements for zoning approval: [xf YES [ ] NO If "no" please explain on a separate attachment. Signature: ~n7 Date: _%'k' Y '2!!U Name of Person to Contact W,fYt (N ~1~ I~r' v v Phone: 6&3 T2--3 C--2" Address: C _[L 6 bUks CL4 CZ; 40, z ONLY-- [ ] Application for a new license [ ] Change of Ownership [ ] Granting of a License [ ] New secured unit [ ] Name Change [ ] Increase/Decrease of Beds [ ] Action taken against the License [ ] Facility Closure 1J J~ ~f Rte J-e°fkys en (fa Change USE Effective: Change effective: Change effective: Effective: Effective: [ ] Initial Notification to Zoning Dept. date: , by: 1, [ ] Final Notification to Zoning Dept date: by: Spy R_ i~ t A CL 1-1 g-/~ Y HEALTH FACILITIES AND EMERGENCY MEDICAL SERVICES DIVISION 4300 Cherry Creek Drive South State Licensure Program Denver, CO 80246 Assisted Living Residences Voice: 303-692-2800 Fax: 303-753-6214 www.cdphe.state.co.us/hf/hfd.asp Form: Sign off for Local Authorities FIRE DEPARTMENT pF e020 ye0 0 t ~ 1896 Colorado Department of Public Health and Environment Written evidence of compliance with local fire codes must be obtainer[ Contact the city or county departments in your area and have the director or designee sign below or otherwise indicate approval Return this form, signed by the proper authorities, to complete your license application. A final inspection cannot be conducted until these approvals are obtained A license cannot be issued until the completed form, with the original signature, is on file with the Division. Name of Facility: Te m-en o S E14-y- Cc. f'e Cc rr p4 nX ! AAA----. !iii TeiLr- IJAeat• RicAaD Jel yfon CCU Pyoo33 No. of Licensed Beds Requested: S Name of Person to Contact: C Yy~'i n ti S vJ iI Phone: -3 q53 I34Fax: ( 7~r~ - r}f~ A7a1~. Fire Department having Jurisdiction: Lid eat` ki2P The above-named facility meets the requirements for fire safety. [ K, YES [ ] NO If "no" please explai ~separate chm" orA the Comments section, below. Signature: Name of Person to Contact Address: l`:~,/ zjPS% CODE(S) APPLIED AND EDITION: OFFICE USE ONLY-- OFFICE USE ONLY-- ] [ ] Application for a new license [ ] Change of Ownership [ ] Granting of a License [ J New secured unit [ ] Name Change [ ] Increase/Decrease of Beds From - to: _ Phone: (;caZ '11°-? 'Fax: 3O3 USE USE ONLY Change effective: Change effective: Change effective: [ ] Action taken against the License [ ] Facility Closure [ ] Initial Notification to Zoning Dept. date: by: Notification to DATE, Name: Organization: Fax: Phone: A-A'cc a-a err, r°tYr~i 7~b~L HGG. - ,J,anvtirix~N~+ti%f' From: S Division: Planning 9~- Building)O Engineering ❑ Subject: # of Pages (Including cover page) Comments: Original to follow in the mail Yes ❑ No W03 MWNViS 3QOW >10 i-insJa b0 (S) 3E)Vd E7:00:00 NOIldana VTE9ESL£0E6 3WVN/'ON XV-d EZ:60 9I/90 3WI1`3iVG £L£99Zf930NEI #'63S 9b8Z9£ZE0£ X31 t98Z9EZE0E xv1 DNINNV7d 3WVN VZ:60 L00Z/91/90 3WI1 1a0d3N NOIIVDIJI63A NOISSIWSNVai DATE Name:~r(l1 Organization: _ Pax: h Phone: From: sLI Division: Planning_ Building Engineering Subject: ELp =8S # of Pages: 1_I_ncluding cover page) Comments: 0 6 / o - l a r U L L ~ ho ~~l e S ( .if ~ r Original to follow in the mail 0 Yes KNo W03 G6VGNd1S 3QOW NO i-inSM V0 (S)39vd L T : TO :00 NOI1t dnci OT08Z£ZCOE6 3WVN/'ON Xdd 9Z:60 9T/90 3WI1`3iVG ELE99Zf530J9 #'JAS 9V8Z9£ZE0E X31 L58Z9EZE0£ : Xdd ONINNV-ld 3WVN LZ:60 L00Z/9T/90 3WI1 1a0d3N NOI1dOIEH3A NOISSIWSNVdi GATE 5/&6-1 Name: Organization: Fax: Phone: From: Division: Subject: # of Pages: Comments Ics Original to fallow in the mail D Yes KNo W03 QaVGNViS 3QOW )10 i-OS3a V0 (S)39Vd LT:T0:00 NOI1tlana V666ZV6£0£6 3WVN/'ON Xd9 BZ:60 9T/90 3WI1`31dQ £LE99Zf93069 9VSZ9£Z£0£ LSBZS£Z£0£ 9NINNTId H:60 L00Z/9T/90 Planning Building Engineering 11 ~y~'-r ~~2htS (Includina.cover pane) H #'a3S 131 XVA 3WVN 3WI1 1a0d3a N0IiVDI3Ia3n NOISSIWSNVdI :,(q :al¢p I aQ uiuoZ o; uoil¢ogiloN I¢ut3 [ ] :Xq - :mvp -1daQ 2ucnoZ oI uoil¢09?I0m FMUI [ ] :anllaa33g a.lnso1O ,CIIIIO¢d [ ] :antloal3g asuool-I aql Isul¢2¢ u031¢I uolloV [ ] :anlloajja a2u¢gD :3nu0a33a a2ueg0 :antioal;a a2u¢gD :ol :wo.13 spag3o as¢aioeQ/as¢aioul [ ] asuego aw¢N [ ] Ilun painoas maN [ ] asuaolZ ¢;0 2upugio [ ] dlgs.IaumO3o a2uLgo [ ] asuoog mau u .to; uolleollddy [ ] limo gsfl gsfl 30I130 --LINO gsfl aomao --A I to gso - -:ssalpPV :auoyd :13UJU03 of uos.lod;o oumm aI¢Q :amleuslq •luaulgo=13 alunaas u uo uI¢Idxo as¢ald ,ou,, 3I ON [ ] SgA :I¢noidd¢ 2u1ppq 10; sluaucannbai oEp slaaul /4!1!o¢3 paw¢u-anoq¢ aq L ggp~ aY(7 :uollolpsunf 2uln¢y Iuawll¢daQ 2mp1mg •-freLo~b~ o~L :auogd 15s nS- td (L 0. 1/1 :10uluo0 01 uosiad JO aw¢N :palsonbod spag posuaot7 30 oN ,Cluno0 Koo ~~oo~ C~,~ `e`itar d'!c~ fin`! :ssalPPt+ U0 Saua~clalL :,(IIII0¢33oaul¢N •uorsmia ay1 WPH allf uo q `ammmkislnu18uo ay, gllm `u<1ofpalalduioa 0111 plum pans aq louuna asuaoy y pau:nlgo ata slneolddn asagl lllun palanpuo0 aq louuna uotlaadsut lnu:f V uolMJgddv asua0tl lno f aialdmioi of `salnioginv 1adoid agl ,fq p0u81s ""Jof slgi umlag Ineolddo alna?put aslwaglo to molaq u&s aau&sap !o joloalrp agl a inq pun najo tno f al sluaml1ndap dlunoa !o ,f)P aql 130luoD paulnlgo aq knot sapoa 8ulpl?nq Inool gl10A a0uvlldw0J fo a0uaptea u0WJAI .LAIHN LHVClaa 9AIIQ'IIfIg sai;!aoginV leaoZ aoj jjo u&g :ulroj dse'p3W3Wsn•oo•alsls•ogdpo'm m VIZ9-£SC£0£:xu3 00SZ-Z69-£0E:93ton saMapisag 2utnlZ pa;sissV 9vz08 00 `lanuaQ ut¢ 2oxd amsuaai7 alelg {lnog anuQ 1021O X110113 00£4 NOISIn1Q S331na3S IVJIa3W AJNMAMW3 UNV S31.L171JV3 n.LIV3H HEALTH FACILITIES AND EMERGENCY oe; cow MEDICAL SERVICES DIVISION 4300'Cherry Creek Drive South State Licensure Program Denver, CO 80246 Assisted Living Residences t+,e,s Voice: 303-692-2800 Fax: 303-753-6214 www.cdphe.state.co.us/hf/hfd.asp Colorado Department oEPub GcHealth Health and Environment Form: Sign off for Local Authorities FIRE DEPARTMENT Written evidence of compliance with local fire codes must be obtained Contact the city or county departments in your area and have the director or designee sign below or otherwise indicate approval Return this form, signed by the proper authorities, to complete your license application. A final inspection cannot be conducted until these approvals are obtained A license cannot be issued until the completed form, with the original signature, is on file with the Division. Name of Facility : Te m -erl o s e_14 ✓ (,i re Co mpa n y ~soo33 3//3 Te%li?)- Sf✓~e~ lJA-e4t- reioAp Jkei yrorl 60 Address: CITY COUNTY No. of Licensed Beds Requested: 8 Name of Person to Contact: V~ C.7ro~'i nai S v4,-1-- Phone: 3O3 95 G Fax: ( Fire Department having Jurisdiction: Wheat- '~'rcP~ 7o 9Z 07a5L The above-named facility meets the requirements for fire safety. [ YES [ ] NO If "no" please explain orL,a, separate attachment or in the Comments section, below. Signature: Name of Person to Contact: _ v. CODE(S) OFFICE USE ONLY-- _ - Phone: ! Fax: [ ] Application for a new license [ ] Change of Ownership [ ] Granting of a License ( j New secured unit [ ] Name Change [ ] Increase/Decrease of Beds From: to: Y-- OFFICE USE ONLY USE ONLY Change effective: Effective: Change effective: Change effective: [ ] Action taken against the License Effective: [ ] Facility Closure Effective: [ ] Initial Notification to Zoning Dept. date: by: f 1 Final Notification to Zoning Dept date: by: HEALTH FACILITIES AND EMERGENCY MEDICAL SERVICES DIVISION State Licensure Program 4300 Cherry Creek Drive South Denver, Co 80246 Assisted Living Residences Voice: 303-692-2800 Fax: 303-753-6214 www.cdphe.state.co.us/hf/hfd.asp Form: Sign off for Local Authorities ZONING DEPARTMENT 9 Written evidence of compliance with local zoning codes and ordinances must be obtained Contact the city or county departments in your area and have the director or designee sign below or otherwise indicate approvaL. Return this form, signed by the proper authorities, to complete your license application. A final inspection cannot be conducted until these approvals are obtained A license cannot be issued until the completed form, with the original signature, is on file with the Division. Name of Facility: 'rRr n.¢ancs 61ke Ca re Cempcrr+y 3113 T-Olef Sir, No. of Licensed Beds Requested: ~oF c% a, h ' 0 ~ Qa Colorado Department of Public Health and Environment "1`k tmj R/ P,,~Q JeYfiys o-.-) Ca Name of Person to Contact: y+ C hd rGt SyAi t Phone: 3Q~ 31 q Fax: ( - L cQ 7ao 2?6 67~5< Zoning Department having Jurisdiction: W J, Q The above-named facility meets the requirements for zoning approval: YES [ ] NO If "no" please explain on a _ separate attachment. Signature: Date: =12 ~G j~ 2d S~ W03 2t : Name of Person to Contact: e1 CV i2E_QkP ✓ Phone: 6 1`2,3f' ( o ~U l-u wj- . q e - Sill /&2 'Zcl. t _Wlnv J2~2!!F c-, UJ Address: CI Y-- OFFICE [ ] Application for a new license [ ] Change of Ownership [ ] Granting ofa License [ ] New secured unit [ ] Name Change [ ] Increasebecrease of Beds From: to:_ [ ] Action taken against the License [ ] Facility Closure Y-- ,Y ONLY Change effective: Effective: Change effective: Change effective: Effective: Effective: [ ] Initial Notification to Zoning Dept. date [ ] Final Notification to Zoning Dept date: • by: by: 81 - b-14 PxAla-~ /V~ `2 j Q Ta in 3 / day> i l «caw~, ~f p I / ~1~~~6~'~ Orly NCB A1d 7-r6,~~ and fL~, 7C-4)l`(30- ~~"FTC a5 A14 0 ,,r/ pp ildr /C(Zj F-re P n( &rdc'"o- i ru &'e~" d~11~i ~ e Ate%~ _ Icy ~?Pd ~ f ~<1- ~~u c»- " Ai" ~\et, a~yL -A4 VkA ~ - a V,4 1 \Y1 0j\j\ nko~ Gh., orb 'w PROPERTY OWNER AND ALL CUP Pursuant to the 1997 Edition and the Uniform Code for the Abatement of Dangerous Buildings, the 1997 Uniform Housing Code and the 2003 International Property Maintenance Code, the following property is in violation. According to County Records you are the property owner of the described property in violation. Property Owner: Attn: ' hl~y_ i mil- ovrtr iCr\n~~ N c, ~x 3 ' 7s3 - (o Zi Li January 3, 2007 Temenos Elder Care Company 3113 Teller Street Wheat Ridge CO 80033 Charles ad Ellen Knapp Z3 3 - 2 80 6 3050 15`1 Stree Boulder Colorado 80304 All Current Occupants of 3113 Teller Street ~11 Wheat Ridge CO 80033 V v t S t r~ cs-~zx.~F? _ O 7 c P )0 Barths. Block 1, Key OOH, Section 26, Township 3, p or commonly known as: 3113 Teller Street. Wheat Ridge _coloraao-2SUU33 NOTICE The property owner, and all current occupants, are hereby notified that the undersigned - Building Official of Wheat Ridge, Colorado, has found the building located on the above described real property to be a Dangerous Building within the meaning of Section 302 of the Uniform Code for the Abatement of Dangerous Buildings, 1997 edition, as adopted by the City of Wheat Ridge, Colorado ("Code"), as more particularly set out below: The building is being used for dwelling purposes and is in violation of the Uniform Code for the Abatement of Dangerous Buildings, sections in bold are the sections that this property is in violation of. SECTION 301- GENERAL For the purpose of this code, certain terms, phrases, words and their derivatives shall be construed as specified in either this chapter or as specified in the Building Code or the Housing Code. Where terms are not defined, they shall have their ordinary accepted meanings within the context with which they are used. Webster's Third new International Dictionary of the English Language, Unabridge, copyright 1986, shall be construed as providing ordinary accepted meanings. Words used in the singular masculine gender include the feminine and the feminine the masculine. BUILDING CODE is the International Code Council, as adopted by this jurisdiction. DANGEROUS BUILDING is any building or structure deemed to be dangerous under the provisions of Section 302 of this code. HOUSING CODE is the Uniform Housing Code promulgated by the International Conference of building Officials, as adopted by this jurisdiction. INTERNATIONAL PROPERTY MAINTENANCE CODE is the 2003 International Property Maintenance Code promulgated by the International Code Council, as adopted by this jurisdiction. SECTION 302 - DANGEROUS BUILDING For the purpose of this code, any building or structure which has any or all of the conditions or defects hereinafter described shall be deemed to be a dangerous building, provided that such conditions or defects exist to the extent that the life, health, property or safety of the public or its occupants are endangered. 1. Whenever any door, aisle, passageway, stairway or other means of exit is not of sufficient width or size or is not so arranged as to provide safe and adequate means of exit in case of fire or panic. 2. Whenever the walking surface of any aisle, passageway, stairway or other means of exit is so warped, worn. Loose, torn or otherwise unsafe as to not provide safe and adequate means of exit in case of fire or panic. 3. Whenever the stress in any materials, member or portion thereof, due to all dead and life loads, is more than one and one half times the working stress or stresses allowed in the Building Code for new buildings of similar structure, purpose or location. 4. Whenever any portion thereof has been damaged by fire, earthquake, wind, flood or by any other cause, to such an extent that the structural strength or stability thereof is materially less than it was before such catastrophe and is less than the minimum requirements of the Building Code for new buildings of similar structure, purpose or location. 5. Whenever any portion or member or appurtenance thereof is likely to fail, or to become detached or dislodged, or to collapse and thereby injure persons or damage property. 6. Whenever any portion of a building, or any member, appurtenance or ornamentation on the exterior thereof is not of sufficient strength or stability, or is not so anchored, attached or fastened in place so as to be capable of resisting a wind pressure of one half of that specified in the building Code for new buildings of similar structure, purpose or location without exceeding the working stressed permitted in the Building Code for such buildings. 7. Whenever any portion thereof has wracked, warped, buckled or settled to such an extent that walls or other structural portions have materially less resistance to winds or earthquakes than is required in the case of similar new construction. 8. Whenever the building or structure, or any portion thereof, because of (i) dilapidation, deterioration or decay; (ii)faulty construction; (iii) the removal, movement or instability of any portion of the ground necessary for the purpose of supporting such buildings; (iv) the deterioration, decay or inadequacy of its foundation; or (v) any other cause, is likely to partially or completely collapse. 9. Whenever, for any reason, the building or structure,,pranX= on thereo , is ma festlyr~ unsafe for purpose of which it is being used. ° 6+~teLS OL it b 10. Whenever the exterior walls or other vertical structural members list, lean or buckle to such an extent that a plumb line passing through the center of gravity does not fall inside the middle on third of the base. 11. Whenever the building or structure, exclusive of the foundation, shows 33 percent or more damage or deterioration of its supporting member or members, or 50 percent damage or deterioration of its non-supporting members, enclosing or outside walls or coverings. 12. Whenever the building or structure has been so damaged by fire, wind, earthquake or flood, or has become so dilapidated or deteriorated as to become (i) an attractive nuisance to children; (ii) a harbor for vagrants, criminals or immoral persons; or as to (iii) enable persons to resort thereto for the purpose of committing unlawful or immoral acts. 13. Whenever any building or structure has been constructed, exists or is maintained in violation of any specific requirement or prohibition applicable to such building or structure provided by the building regulations of this jurisdiction, as specified in the Building Code or Housing Code, or of any law or ordinance of this state or jurisdiction relating to the condition, location or structure of buildings. 14. Whenever any building or structure which, whether or not erected in accordance with a all applicable laws and ordinances, has in any non-supporting part, member or portion less than 50 percent, or in any supporting part, member or portion less the 66 percent or the (i) strength, (ii) fire-resisting qualities or characteristics, or (iii) weather-resisting qualities or characteristics required by law in the case of a newly constructed building of like area, height and occupancy in the same location. 15. Whenever a building or structure, used or intended to be used for dwelling purposes, because of inadequate maintenance, dilapidation, decay, damage, faulty construction or arrangement, inadequate light, air or sanitation facilities, or otherwise, is determined by the health officer to be unsanitary, unfit for human habitation or in such a condition that is likely to cause sickness or disease. 16. Whenever any building or structure, because of obsolescence, dilapidated condition, deterioration, damage, inadequate exists, lack of sufficient fire-resistive construction, faulty electric wiring, gas connections or heating apparatus, or other cause, is determined by the fire marshal to be a fire hazard. 17. Whenever any building or structure is in such a condition as to constitute a public nuisance known to the common law or in equity jurisprudence. 18. Whenever any portion or a building or structure remains on a site after the demolition or destruction of the building or structure or whenever any building or structure is abandoned for a period in excess of six months so as to constitute such building or portion thereof an attractive nuisance or hazard to the public. The 1997 Uniform Housing Codes states: SECTION 1001- DEFINITIONS 1001.1 General. Any building or portion thereof that is determined to be an unsafe building in accordance with Section 102 of the Building Code, or any building or portion thereof, including any dwelling unit, guest room or suite or rooms, or the premises on which the same is located, in which there exists any of the conditions referenced in this section to an extent that endangers the life, limb, health, property, safety or welfare of the public or the occupants thereof, shall be deemed and hereby are declared to be substandard buildings. 1001.2 Inadequate Sanitation. Buildings or portions thereof shall be deemed substandard when they are when they are in sanitary. Inadequate sanitation shall include, but not be limited to, the following: 1. Lack of or improper water closet, lavatory, bathtub or shower in a dwelling unit or lodging house. 2. Lack of or improper water closets, lavatories, and bathtubs or showers per number or guests in a hotel. 3. Lack of or improper kitchen sink in a dwelling unit. 4. Lack of hot or cold running water to plumbing fixtures in a hotel 5. Lack of hot or cold running water to plumbing fixtures in a dwelling unit or lodging house. 6. Lack of adequate heating facilities. 7. Lack of or improper operation or required ventilating equipment. CI!° 8. Lack of minimum amounts of natural light and ventilation require by this code. 9. Room and space dimensions less than required by this code. 10. Lack of required electrical lighting. 11. Dampness of habitable rooms. 12. Infestation of insects, vermin or rodents as determined by the health officer. 13. General dilapidation or improper maintenance. 14. Lack of connection to required sewage disposal system. 15. Lack of adequate garbage and rabbish storage and removal facilities as determined by the health officer. 1001.3 Structural Hazards. Buildings or portions thereof shall be deemed substandard when they are or contain structural hazards. Structural hazards shall include, but not be limited to, the following: 1. Deteriorated or inadequate foundations. 2. Defective or deteriorated flooring or floor supports. 3. Flooring or floor supports of insufficient size to carry imposed loads with safety. 4. Members of walls, partitions or other vertical supports that split, lean, list or buckle do to defective material or deteriorations. 5. Members of walls, partitions or other vertical supports that are of insufficient size to carry imposed loads with safety. 6. Members of ceilings, roofs, ceiling and roof supports, or other horizontal members that sag, split or buckle due to defective material or deterioration. 7. Members of ceilings, roofs, ceiling and roof supports, or other horizontal members that are of insufficient size to carry imposed lads with safety. 8. Fireplaces or chimneys that list, bulge o settle due to defective material or deterioration. 9. Fireplaces or chimneys that are of insufficient size or strength to carry imposed loads with safety. 1001.4 Nuisance. Buildings or portions thereof in which there exists any nuisance as defined in this code are deemed substandard buildings. 1001.5 Hazardous Electrical Wiring. Electrical wiring that was installed in violation of code requirements in effect at the time of installation or electrical wiring not installed in accordance with generally accepted construction practices in areas where no codes were in effect or that has not been maintained in good condition or tha} is not being used in a safe manner shall be considered substandard. , W)Y'it~c, W/O QC✓blat V 1001.6 Hazardous Plumbing. Plumbing that was installed in violation of code requirements in effect at the time of installation or plumbing not installed in accordance with generally accepted construction practices in areas where no codes were in effect or that has not been maintained in good condition or that is not being used in a safe manner shall be considered substandard. 1001.7 Hazardous Mechanical. Mechanical equipment that was installed in violation of code requirements in effect at the time of installation or mechanical equipment not installed in accordance with generally accepted construction practices in areas where no codes were in effect or that has not been maintained in good condition or that is not being used in a safe manner shall a cons dered substandard. J7fyGe- ouc OV(a1Gt. - c&% tM E705(FY4tu~ / ~ dtS.c~oIL * C- oleo vva -Vaec disc~r►►tec 1001.8 Faulty Weather Protections. Buildings or portions thereof shall be considered substandard when they have faulty weather protections, which shall include, but not be limited to, the following: 1. Deteriorated, crumbling or loose plaster. 2. Deteriorated or ineffective waterproofing or exterior walls, roof, foundations or floors, including broken windows or doors. 3. Defective or lack of weather protection for exterior wall coverings, including lack of paint, or weathering due to lack of paint or other approved protective covering. 4. Broken, rotted, split or buckled exterior wall coverings or roof coverings. 1001.9 Fire Hazard. Any building or portion thereof, device, apparatus, equipment, combustible waste, or vegetation that, in the opinion of the chief of the fire department, is in such a condition as to cause a fire or explosion or provide a ready fuel to augment the spread and intensity of fire or explosion arising from any cause shall be considered substandard. 1001.10 Faulty Materials of Construction. The use of materials of construction, except those that are specifically allowed or approved by this code and the Building Code, and that have been adequately maintained in good and safe conditions, shall cause a building to be substandard. 1001.11 Hazardous or Insanitary Premises. The accumulation of weeds, vegetation, junk, dead organic matter, debris, garbage, offal, rat harborages, stagnant water, combustible materials, and similar materials or conditions on a premises constitutes fire, health or safety hazards that shall be abated in accordance with the procedures specified in Chapter 11 of this code. 1001.12 Inadequate Exits. Except for those buildings or portions thereof that have been provided with adequate exit facilities conforming to the provisions of this code, buildings or portions thereof whose exit facilities were installed in violation of code requirements in effect at the time of their construction or whose exit facilities have not been increased in number or width in relations to any increase in occupant load due to alterations, additions or change in use or occupancy subsequent to the time of construction shall be considered substandard. Notwithstanding compliance with code requirements in effect at the time of their construction, buildings or portions thereof shall be considered substandard when the building official finds that an unsafe condition exists through an improper location of exits, a lack of an adequate number or width of exits, or when other conditions exist that are dangerous to human life. 1001.13 Inadequate Fire-Protection or Fire-Fighting Equipment. Buildings or portions there of shall be considered substandard when they are not provided with the fire-resistive construction or fire- extinguishing systems or equipment required by this code, except those buildings or portions thereof that conformed with all applicable laws at the time of their construction and whose fire-resistive integrity and fire-extinguishing systems or equipment has been adequately maintained and improved in relation to any increase in occupant load, alteration or addition, or any change in occupancy. 1001.14 Improper Occupancy. All buildings or portions thereof occupied for living, sleeping, cooking or dining purposes that were not designed or intended to be used for such occupancies shall be considered substandard. The following is a list of items that shall be fixed to meet code. N 0 1. Bedroom windows do not meet egress requirements of the 5.7 5y Fk , Uniform Building Code or the Intern tional Building Code as e required in Section R310. a7PwtRS aenal ~paa~ ~kaQS , O 1~2. Minimum required width on the stairwayy does noj neet cod according to section R311.5.1. - Shxt2 I.i 51'41 be- (G W W&O C} rC3. No Building Permit was pulled for electrical work-- c9 tC4. Boiler room needs snake up air for combustion d k5. Hot water shall not be hotter than 140 degrees..- c)tC6. GFCI needed in all bathrooms and kitchen outlets. `ten\\ C.c~ v'„ti U ic7. All exhaust fans must be vent to the outside and need to be working. ~ U-04 Fow I'M 864~l Vwf ` Nov p1„dttw~ U 1C8. Ceiling of porch is sagging and i to fall down on occupants. Needs work to meet3Qlb now load. N G 9. Several bedrooms do not have egress windows I WQ)10. Need handrail on stairways. - 6"4 4%mleS/ cu6kle' ~ t~ 11. Bedrooms in basement have no egress win ows~ 12. Dryer vent is not to code. /~a,~l ~4r~.~ ~ l~~9tt~ N o 13. Exterior stairs are not to code and are considered to be dangerous no rise shall be greater than 8" and a flight of stairs shall not exceed 12 feet in height without a landing. No14. No handrail to code on exterior stairs. N ° p KI5. Stairs in basement do not meet code with no more than 3/8" difference between treads on a flight of stairs. PJcl 16. Chair lift does not meet code. Must remove chair lift. Stair width is to narrow for us of chair lift. This is a life safety issue yc ti' Code states minimum 36' tdth. Exterior stairs are still 5 P 3 3 covered with snow 5 days a er last snow storm. f't r' 17. NOTE THERE MAYBE OTHER ITEMS THAT WERE NOT ADDRrESSED. I Iq. L A oUC.A. }61; de b - AID P n abour<~" bas ~2 19, cW onl bDikr_ ins 1 Zo, + r)o~- ai~n( ORDER The City of Wheat Ridge Building Official has determined the building referenced above to be a Dangerous Building. The owners are ordered to pull a building permit to fix the deficient items. If such items are not fixed by February 12, 2007, the Building Department will post this building as a Dangerous Building. Pursuant to Code the property owner and all occupants are hereby ORDE TO CEASE AND DESIST occupancy and use of the above described building. The Building Official shall cause the property to be posted with the attached Notice to prevent occupancy after March 30, 2007 and shall take action to remove all occupants from the building. 1. II. Section 801 in the Uniform Code for the Abatement of Dangerous Buildings states, " 801.1 Procedure. When any work of repair or demolition is to be done pursuant Section 701.3, Item 3, of this code, the building official shall issue an order thereof to the director of public works and the work shall be accomplished by personnel of this jurisdiction or by private contract under the direction of said director. Plans and specifications therefore may be prepared by said director, or the director may employ such architectural and engineering assistance on a contract basis as deemed reasonably necessary. If any part of the work is to be accomplished by private contract, standard public works contractual procedures shall be followed." Section 801.2 states, "801.2 Costs. The cost of such work shall be paid from the repair and demolition fund, and may be made a special assessment against the property involved, or may be made a personal obligation of the property owner, whichever the legislative body of this jurisdiction shall determine is appropriate." REMEDIAL ACTION 1. The property owner must apply for and obtain a City of Wheat Ridge building permit to correct the following deficiencies. III. All deficiencies shall be fixed but are not limited to the items on this list by February 12, 2007 or the Building Official shall cause the property to be posted with the attached Notice to prevent occupancy after March 30, 2007 and shall take action to remove all occupants from the building.. APPEAL OF THIS NOTICE AND ORDER Any person having record title or other legal interest in the above described premises may appeal this Notice and Order or any action of the Building Official to the Building Code Advisory Board or known as the Board of Appeals pursuant to section 112 of the Code, provided that the appeal is made in writing as provided in the Code and filed with the Building Official within ten (10) days from the date of service of this Notice and Order. Failure to appeal will constitute a waiver of all rights to an administrative hearing and determination of this matter. FILING OF AN APPEAL SHALL NOT STAY THE EFFECTIVENESS OF THIS NOTICE AND ORDER. It is a misdemeanor to occupy this building after March 30, 2007 or to remove or deface this notice. BY ORDER OF THE CITY OF WHEAT RIDGE'S BUILDING OFFICIAL 303-235-2853 303-570-7510 Chadley Root, Building Official WHEAT RIDGE FIRE PROTECTION DISTRICT PO BOX 507 • 3880 UPHAM STREET • WHEAT RIDGE, COLORADO 80034-0507 303.403-5900 • FAX 303.940-0350 WWW.WRFIRE.ORG c%-~ 31 5-6ti-6--Sg9 YJ S,\t3 May 26, 2006 \ 364 Street L+uy- \N r,% Boulder, Colorado 80301 (Sa#e ysteem `3~IarkOverlan Re: 3113 Teller Street- Temenos House Fire Alarm. The following requirements are made under the 2003 International Fire Code adopted by the Fire Board of the Wheat ridge Fire Protection District and the City Council of the City of Wheat Ridge, Colorado. - 1. The fire alarm shall remain in service during all phases of construction. 2. If the alarm is out of service for any time period a fire watch shall be initiated and logged every half hour. 3. All devices shall be numbered and addressable. 4. A rough in inspection shall be scheduled with the Fire District as well as the City building inspector. . 5. A complete test of the entire system shall be performed prior to calling for a final inspection. 6. All means of egress shall remain clear during all phases . of construction. 7. All Fire Lanes shall remain clear of all construction vehicles and supplies. 8. Any changes to the approved plans shall be submitted to the Fire District for approval. 9. Keys shall be provided for the fire alarm panel to be placed in the required Knox box on site. Any questions regarding these requirements please contact me at the Fire district. Rev' ed by, Douglas J. Saba Fire Marshal Fire Code Inspector #5083898-66 Colo t Dm ) G 1 O z Y~++ ~c a o < ~ w Z Y f` ~ R m 60 c: z b° co w ~ ',m w y ~ v a -i a~ U O c -i m 00 o v o w w a CGS n~,~ T ~ B,Ny3 o m 8w yrt a C4 a> Correction Notice 14 -1®\(0o Job Address: 3 11 ~ _\ifl_10- Go~-- rvs} b S1 \X 0 hz "-n\ \ ~ ci r When corrections have been made, call for re-inspection at 303-234-5933. A -IC COMMUNITY DEVELOPMENT DEPT. Inspection Services Division (303) 235-2855 DO NOT REMOVE THIS NOTICE ie St ss fn V-k Q =i, y r em 5-r \ Y- ~_Tt eo ~r.v> Property appraisal system General Inf,orrnation Previous 2 OF 3 Next Schedule: 021548 Status: Active Parcel ID: 39-264-03-018 Property Type: Apartment Property Address: 03113 TELLER ST WHEAT RIDGE CO 80033 Mailing Address: 03050 15TH ST BOULDER CO 80304 2614 Neighborhood: 261 - Subdivision Name: 064800 - BARTHS Page 1 of 1 Print Owner N\aa E5 KNAPP cka KNAPP EI6ti Block Lot Key Section Township Range QuarterSection Land c 001 0002 OOH 26 3 69 SE 18121 Total 18121 Sale Date Sale Amount Deed Type Recepti 08-10-1978 0 CONVE 06-01-1979 88,000 79049E 04-15-1997 89,000 Special Warranty Deed - Joint Tenancy F0401_C Assessor Parcel Maps Associated with Schedule map39726-4-df Acrobat Reader is required to view PDF's. Go to Asoin Mai) for this Schedule http://wwl4.co.jefferson.co.us/ats/displaygeneral.do?sch=021548&offset=l 1/3/2007 c t City of Wheat Ridge Building Permit Number: m Community Development Dep~3ar]t~m~ent Date: { { F COL ORPOO COMMERF, L (X „tl'3.(' ULTTTM".iG"A k Y Property Owner: (en` oci epoelkoc ' ULa _Property Address: `3113 CR-GrPPhone: ?o 3- z Contractor License No.: `6 faG Z Company: Sk~G Sys+e.KVj (kc Phone: 303-ofgq-!! OWNERICONTRACTOR SIGNATURE OF UNDERSTANDING AND AGREEMENT.::. Bul/dinp Dept. Valuation Figure; $ . I hereby certify that the setback distances proposed by this permit application are accurate, and do not violate. applicable ordinances, rules. or regulations of the City of Wheat Ridge orcovenants, easements or restrictions of record; that all measurements shown, and allegations made are accurate; that I have read and agree to abide by all conditions printed on this application and that I assume full responsibility for compliance with the Wheat Ridge Building Code (I.B.C) and all other applicable Wheat Ridge Ordinances, for work under his permit. Plans subjectto field inspection. . s (OWNER)(CONTRACTOR) SIGNED 'I DATE (.0 `(OWNER)(CONTRACTOR):PRINTED~(~/A tGNC- J.t, VEI?4,6VyDATE_ Use of Space (description):_Ssi S Fic( l~ i , aG`~d Description of work: roc aj&vv, a Q7(PrA taut l Sq. Ft. added 4. BUILDING DEPARTMENT USE ONLY SIC: Sq.Ft.: ZONING COMMENTS: Approval: Zoning: Litt.( q~( t' BUILDING COMMENTS: A16 P®~'9 l JI 9 Approval: ee / isr r~ PUBLIC WORKS COMMENTS:.. Approval: IRE DEPARTMENT COMMENTS: 4,Q Z Approval: Occupancy: Walls: Roof: Stories: Residential Units: - Electrical License No: Plumbing License No: Mechanical License No: Company: Company: Company: - Expiration Date: Expiration Date: Expiration Date: Approval: Approval: Approval: (1) This permit was issued in accordance with the provisions set forth in your application and is subject to the laws of the State of ° "Colorado and to the Zoning Regulations and Building Codes of Wheat Ridge, Colorado or any other applicable ordinances of the City. (2) This permit shall. expire if (A) the work authorized is not commenced within sixty (60) days from issue date or (B) the building - ' ' authorized is suspended or abandoned for a. period of 180 days. . (3) If this permit expires, a new permit may be acquired for a fee of one-half the amount normally required, provided no changes have been orwill be made in the original plans. and specifications and any suspension or abandonment has not exceeded one (1)year.. If changes have been or. if suspension or abandonment exceeds one(1)year, full fees shall be paid for a new permit. (4) No work of any manner shall be done that will change the natural flow of water causing a drainage problem. (5) Contractor shall notify the Building Inspector twenty-four (24) hours in advance for all inspections and shall receive written approval on inspection card before proceeding with successive phases of the job. ` - (6) The issuance of a permit or the approval. of. drawings and specifications shall not be construed to be a permit for, nor an - approval of, anyviolation of the provisions of the building codes orany otherordinance, law, rule orregulation. All plan review ' is sub o ield i . . chief -Gilding Official City of Wheat Ridge Comm. Fire Alarm PERMIT - 060474 PERMIT NO: 060474 ISSUED: 06/12/2006 JOB ADDRESS: 3113 TELLER ST EXPIRES: 12/12/2007 DESCRIPTION: Fire alarm alteration. (Assisted living facility) 'DcF . tz . zoo6 CONTACTS owner 303/233-2808 Ellen Knapp Temenos House go 303/444-1191 Larry Halpern 01-8662 Safe Systems, Inc. PARCEL INFO ZONE CODE: UA USE: UA SUBDIVISION: UA BLOCK/LOT#: 0/ FEE SUMMARY ESTIMATED PROJECT VALUATION: 5,500.00 FEES Permit Fee 162.90 Total Valuation .00 Use Tax 99.00 - TOTAL 261.90 X2 Comments: I hereby certify that the setback distances proposed by this permit application are accurate, and do not violate applicable ordinances, rules or regulations of the City of Wheat Ridge or covenants, easements or restrictions of record; that all measurements shown, and allegations made are accurate; that I have read and agree to abide by all conditions printed on this application d that I assume full responsibility for compliance with the Wheat Ridge Building Code (I.B.C) and all other applicabl 9 YRidgq,07/1~s, for w/rk under this permit'. Plans subject to field inspection. S ignatur~e of cont ct /owner date 1. This permit was sued in accordance with the provisions set forth in your application and is subject to the laws of the State of Colorado and to the Zoning Regulations and Building Codes of Wheat Ridge, Colorado or any other applicable ordinances of the City. 2. This permit shall expire if (A) the work authorized is not commenced within sixty (60) days from issue date or (B) the building authorized is suspended or abandoned for a period of 180 days. 3. If this permit expires, a new permit may be acquired for a fee of one-half the amount normally required, provided no changes have been or will be made in the original plans and specifications and any suspension or abandonment has not exceeded one (1) year. If changes have been or if suspension or abandonment. exceeds one (1) year, full fees shall be paid for a new permit. 4. No work of any manner shall be done that will change the natural flow of water causing a drainage problem. 5. Contractor shall notify the Building inspector twenty-four (24) hours in advance for all inspections and shall receive written approval on inspection card before proceeding with successive phases of the job. 6. The issuance o a per or the`3pproval of drawings and specifications shall not be construed to be a permit for, nor an appro/va ~v'.ii lat. Qn-of"the provisions of the building codes or any other ordinance, law, rule or regulation. All pyan _ s, yAe ,.tef field inspections. Signature of Chief Building Offical date INSPECTION REQUEST LINE: (303)234-5933 BUILDING OFFICE: (303)235-2855 REQUESTS MUST BE MADE BY 3PM ANY BUSINESS DAY FOR INSPECTION THE FOLLOWING BUSINESS DAY. WHEAT RIDGE FIRE PROTECTION DISTRICT PO BOX 507 • 3880 UPHAM STREET • WHEAT RIDGE, COLORADO 80034-0507 303-403-5900 • FAX 303-940-0350 • WWW.WRFIRE.ORG Safe Systems May 26, 2006 Mark Overland 3640 Walnut Street Boulder, Colorado 80301 Re: 3113 Teller Street- Temenos House Fire Alarm. The following requirements are made under the 2003 International Fire Code adopted by the Fire Board of the Wheat ridge Fire Protection District and the City Council of the City of Wheat Ridge, Colorado. 1. The fire alarm shall remain in service during all phases of construction. 2. If the alarm is out of service for any time period a fire watch shall be initiated and logged every half hour. 3. All devices shall be numbered and addressable. 4. A rough in inspection shall be scheduled with the Fire District as well as the City building inspector. 5. A complete test of the entire system shall be performed prior to calling for a final inspection. 6. All means of egress shall remain clear during all phases . of construction. 7. All Fire Lanes shall remain clear of all construction vehicles and supplies. 8. Any changes to the approved plans shall be submitted to the Fire District for approval. 9. Keys shall be provided for the fire alarm panel to be placed in the required Knox box on site. Any questions regarding these requirements please contact me at the Fire district. Revi ed by, Douglas J. Saba Fire Marshal Fire Code Inspector #5083898-66 Colo. Permit No. Fire Protection District Street • Wheat Ridge, Colorado 80034-0507 _ 303-940-0350 Fax • www.wrfire.org M Site Information ~V Address: ( 1'. ♦ S (A J pe Zr d..19 Business: S a 1 Contact: (F.'s.'yaa2 } _ py Phone: 3yt -,233 ~*oS v I attest the above information to be accurate. I have received and reviewed the Inspection Compliance and the Fee Schedule. This permit is the ) property of the Wheat Ridge Fire Protection District and is issued subject to conditions contained herein. Upon any failure of any condition including rn failure of clearance of any permit payment, this permit is subject to immediate revocation and the permit must be returned upon demand: to a representative of the Wheat Ridge Fire Protection 1 ! inn signature of Applicant: z 4? r( NOTICE: If construction is started prior to the i uance of a permit,S*I,i,E~3) times the normal fee will be assessed. INSPECTION BY FIRE PROTECTION DISTRICT" REQUIRED? Y ❑ NO fT1 . Post this permit in a conspicuous place. Requestrequired inspections a minimum o?'69e days in advance at303403-5901. TYPE OF PERMIT FORMULA (see fee schedule sheet) FEES Tank Inspection No. of Tanks= Review Alarm System Plans System Value= Review Sprinkler System Plans System Value= Review Misc. System Plans System Value= Review Building Plans Valuation= Special Handling or Use Plans Valuation= ' TOTAL FEES DUE ~ Cllr Ma X O Date Paid /10 Amt. Paid r. t Method ,j Initials t m ❑ Total Bldg. Tye Alteration ❑ New A partial ❑ Other: pt Field. Inspections and Dates: Z Hydrostatic Tests and Dates: v Comments: ~ X FIRE PROTECTION DISTRICT APPROVAL IS REQUIRED PRIOR TO THE ISSUANCE OF THIS PERMIT. H ❑ APPROVER -As SUBMITTED o ~ Ia"CONpD1O/YALLY APPROIED (Sge om nts.) BY TITLE rr .«s f A / DATE <w.,: TYPE OF PERMIT FORMULA (see fee schedule sheet) FEES _ Site Assessment (Re-Submittal) No. of Sites Plan Revision (Re-Inspect) No. of Hours After hours inspection 2 Hours + No. of Hours TOTAL FEES DUE FINAL APPROVAL BY TITLE DATE Date Paid Amt. Paid Method Initials e:.._~..A.. Q-st ,11011 M X 3 H CONDITIONAL Fl relffe®ALarms www.frrefite.com The Fire•Lite MS-5024UD is a 24-volt, five-zone fire alarm control panel with built-in communicator and remote-site Upload/Download capability. The integral communicator transmits event information (alarms, troubles, super- visories, faults, etc.) to a UL listed central station. The MS- 5024UD may be used in a variety of cost-effective applica- tions, including: local fire alarm control panel (communi- cator disabled), fire alarm control panel/communicator, stand-alone sprinkler supervisory communicator or slave communicatorto a UL-listed host fire alarm panel (requires N.O. dry contacts to trigger 5 channels). Selectable trans- mission formats allow the MS-5024UD to communicate to virtually all central stations. FEATURES • Five programmable Initiating Device Circuits (zones). Each zone may be programmed for: ./Two-wire smoke detectors. ✓ N.O. contact devices (pull, heat). ✓ Four-wire smoke detectors. Waterflow operation. ✓ Supervisory operation. Auto-reset Supervisory operation. • Two built-in, Class A or B (Style Z or Y) Notification Ap- pliance Circuits (NACs). • Notification Appliance Circuits may be programmed: Silenceable. ✓ Non-Silenceable (a strobe circuit can keep flashing after the panel is silenced). ✓ Auto-Silence (Program 5 to 30 minutes). ./Silence Inhibit (60 seconds). ✓ Coding (March Time, Temporal, California). • 3.0 amps of Notification Appliance power, expandable to 5.0 amps (meets the critical power requirements forADA and UL-1971 devices). • Two built-in Form-C Alarm and Trouble relays. • Supervisory and communication fail outputs. • Dual-line rotary- or Touch-TonelD-dial DACT interfaces to public telephone network (leased phone lines are not required). • 24-Volt operation. • Built-in voltmeter measures: ✓ Zone voltage. ✓ Primary AC line voltage. ✓ Battery voltage. ✓ Notification Appliance Circuit(s) voltage. ✓ Resettable 24-volt power. • Surface Mount Technology (SMT). • Fully programmable via built-in keypad (no costly exter- nal programmers necessary). This Alarms is a Honeywell tympany. This document is not intended to be used for installation purposes. We try to keep our product ISO 9001 information up-to-dale and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. For more information, contact Fire•Lite Alarms, One Fire-Lite Place, Northford, Connecticut 06472. ENGINEERING 8 NIMlUNIGTURING Phone: (800) 627-3473, Toll-Free FAX: (877) 699-4105. QUALITY SYSTEMS DF-51348 • 07112/04 - Page 1 of 3 July 12, 2004 DF-51348:• A3-300 MS-5024UD (C/E) Fire Alarm Control Panel with built-in DACT and remote-site Uppload/Download capability Section: Control/Communicators California State Fire l Marshal nn o INDUSTRY ~ 7165-0075:169 CANADA LISTED A FCC 5624 21325785 (MS-5024UD, 1 W6USA-74525-AL-E MS-5024UDE) MS-5024UD Complies with NFPA 72 edition (Local, Central Station and Remote Station (DACT only - not polarity reversal] Fire Alarm Systems). Reporting formats include: ✓3+1, 4+1, 4+2 Standard + Expanded. ✓4+1, 4+2, Ademco Express. Integral battery charger for up to 60 hours of standby power. Fuseless, power-limited technology meets new UL power-limiting requirements. Programmable Alarm Presignal Timer, Alarm Verifica- tion Timer and Optional Trouble Reminder. Single-person walk test. Fire drill function. Zone disable capability (software). 32-Event history buffer with time and date stamp. Accurate real-time clock/calendar. Extensive built-in transient protection. Electronics and operational controls fully enclosed in a lockable cabinet capable of housing up to 7 AH batter- ies. Optional contact-by-zone module and optional remote annunciator. • Optional printer interface for on or off-line printing. • 230 VAC, 50 Hz international version available. 4 Remote Site Upload/Download The MS-5024UD may be downloaded or uploaded, with- out affecting the system fire protection. • Download system programming. • Upload key system information: ✓ Current system status, history and walk test files. ✓ Zone, AC line, NAG 1 and NAG 2, Resettable Power and Battery Voltages. /System Programming. • Upload or Download within one minute without affecting normal fire panel functions. • Multiple security techniques. • Requires PK-CD programming kit, which works with most Hayes-compatible modems (consult factory for listing). Specifications • Single PC board design using Surface Mount Technol- ogy (SMT). • Two modular telephone jacks for connection to RJ31X/ Modules. AC Power • 120 VAC, 50/60 Hz, 2.3 amps. • 230 VAC, 50 Hz, 1.2 amps ("E" suffix). • Wire size: minimum 14 AWG with 600-volt insulation. • Built-in brownout circuitry. • Built-in voltmeter. Communicator • One line-active indicator for each of two phone lines. • "Kiss-Off" signal LED. • Dual "low telephone voltage detect' circuitry. • Programmable event codes per each format. • Up to 62 transmitted events/messages. • Selectable/deselectable transmissions of 62 events. • Five zones may be configured to five channels as a slave communicator (channels are auto-resettable). Communication Formats Express formats allow complete transaction to be com- municated in under 5 seconds • 20 PPS, 3+1 standard and expanded. • 20 PPS, 4+1 standard and expanded. • 20 PPS, 4+2 standard and expanded. • 4+1 and 4+2 Ademco Express. Initiating Device Circuits (zones) The MS-5024UD includes five programmable Initiating De- vice Circuits (zones). Circuits 1, 2, 4, and 5 are Style B (Class B). Circuit 3 is Style D (Class A). Use the CAC-5F, Class A converter module, to convert all Class B IDCs to Class A. Each zone may support two-wire smoke detectors. Pro- gramming options include: • Waterflow - Silenceable/Non-Silenceable. • Supervisory - Standard/Auto-Reset. • Pull Station. Normally Open Contact device. All circuits are power-limited and also fully supervised. They allow up to 100 ohms of line resistance and allow for use of 12 to 18 AWG wire. Page 2 of 3 - DF-51348 - 07112/04 Notification Appliance Circuits • Two Style Z/Y (Class A/B) @ 2.5 amps each. • All circuits are fully power-limited and meet the UL power-limiting requirements, using fuseless technol- ogy. Auxiliary Outputs • Resettable four-wire smoke detector power @ 300mA. • Non-resettable power @ 300 mA. • Integral Form-C Alarm and Trouble relays. • Relay drivers for supervisory and communication fail. CABINET SPECIFICATIONS The cabinet is red with a dark blue overlay. Knockouts on the top, sides, and back provide ease of wire entry. The cabinet can be surface or semi-flush mounted and is com- pact in design. DIMENSIONS: Door: 15-7132" high x 14-7/32" wide (38.655 cm high x 36.115 cm wide). Backbox: 15" high x 14-1/2" wide x 3" deep (38.1 cm high x 36.83 cm wide x 7.62 cm deep). Trim Ring (Part # TR-1-R): 18.125' high x 17.62" wide (46.0375 cm high x 44.7548 cm deep) PRODUCT LINE INFORMATION MS-5024UD Five-zone, 24-volt Fire Alarm Control Com- municator (includes backbox, transformer, tech- nical manual, and a frame & post operating in- struction sheet). MS-5024UDC Same as above with ULC listing and DP- 5024UD Dress Panel. MS-5024UDE Same as MS-5024UD with 230 VAC, 50 Hz transformer (UL listed). XRM-24 120 VAC, 100 VA transformer expands NAG power from 3.0 to 5.0 amps. R7A-5F Five-zone Remote Annunciator mounts to a single gang box (requires ADM-24). ADM-24 Annunciator Driver Module. RM-51F Five-zone Relay Module provides contact-by- zone. CAC-5F Class A Converter Module. Converts all Class B Initiating Device Circuits (zones) to Class A. PRT-24 Printer Interface Module provides an EIA-232 printer output. Includes cable, DB9F and DB25 adapter. PK-CD Upload/Download Utility includes program- ming software (WindowsT compatible CD and Instruction Manual). DP-5024UD Internal Dress Panel (included when order- ing MS-5024UDC). MCBL-7 DACT phone cord, 7 feet long, (two required). BB-17F Battery backbox. Required for batteries over 7 AH. TR-1-R Trim ring. BAT-1242 Battery, 12 volt, 4.2 AH (two required). BAT-1270 Battery, 12 volt, 7.0 AH (two required). BAT-12120 Battery, 12 volt, 12.0 AH (two required, requires BB-17F backbox). BAT-12170 Battery, 12 volt, 17.0 AH (two required, requires BB-17F backbox). 5024UDRB Replacement Mother Board. UL LISTED RECEIVERS compatible with the MS-5024UD Format# (Addresses 16 & 42) Adernco 685(l) Silent Knight ITI (653)) " FBI CP220F6 Osbome Hoffman Models 1&2 Radionics 600(5) Sescoa 3 M surGuard M(9) 2 0 4+1 Aden= E)press ✓ ✓ ✓ 1 4+2 Adeff= Express ✓ ✓ ✓ (8) ✓ 2 3+1/Standard/1800/2300 ✓ ✓ (2) ✓ ✓ (4) ✓ ✓ (5, 6) ✓ ✓ 3 3+1/E*arded/1800/2300 ✓ ✓ (2) ✓ ✓ (4) ✓ ✓ ✓ 4 3+1/Standard/1900/1400 ✓ ✓ (2) ✓ (4) ✓ ✓ ✓ 5 3+1/E)panded/1900/1400 ✓ ✓ (2) ✓ (4) ✓ ✓ ✓ 6 4+1/Startdard/1800/2300 ✓ ✓ (2) ✓ ✓ (4) ✓ ✓ (5) ✓ ✓ 7 4+1/E)panded11800/23W ✓ ✓ (2) ✓ (4) ✓ ✓ ✓ 8 4+1/Standard/1900/1400 ✓ ✓ (2) ✓ (4) ✓ ✓ ✓ 9 4+1/EVanded/1900/1400 ✓ ✓ (2) ✓ (4) ✓ ✓ ✓ A 4+2/Standard/1800/2300 ✓ ✓ (2) ✓ ✓ (4) ✓ ✓ (5) ✓ ✓ B 4+2/EVanded/1800/2300 ✓ ✓ (2) ✓ (4) ✓ ✓ ✓ C 4+21Standarcl/1900/1400 ✓ ✓ (2) ✓ (4) ✓ ✓ ✓ D 4+2/E)panded/1900/1400 ✓ ✓ (2) ✓ (4) ✓ ✓ ✓ E (NOT USED) F (NOT USED) (1) With 685-8 Line Card with Rev. 4.4d software. (2) With 9002 Line Card Rev. 9035 software or 9032 Line Card with 9326A software. (3) Rev. 4.0 software. (4) FBI CP220FB Rec-11 Line Card with Rev. 2.6 software and a memory card with Rev. 3.8 software. (5) Model 6500 with Rev. 600 software. (6) Model 6000 with Rev. 204 software. (7) With Rev. B control card at Rev. 1.4 software and Rev. C line card at Rev. 1.5 software. (8) Model 2 only. (9) Version 1.62 software. DF-51348 • 07112104 - Page 3 of 3 ~tt Models Available ~E.~Vdjtias ` 2400/2400A Photoelectronic 24007H Photoelectronic with Thermal t a 24128/2412BA Photoelectronic 24127X6 Photoelectronic with Thermal 2424 Photoelectronic 2424TH Photoelectronic with Thermal Features • 12 or 24 volt operation • Field sensitivity metering of detector to meet NFPA 72 • Unique optical sensing chamber requirements • Removable cover and insect screen for easy • Twist-on mounting bracket with tamper option cleaning • SEMS screws for easy wiring • Visible LED blinks in standby, latches on in • 3-year warranty alarm • Optional built-in 135°F (57°C) heat sensor • Sealed against dirt, insects, and back pressure Specifications Size: 3.2" (8.1 cm) h, 5.5" (13.9 cm) Sensitivity: 3.0% ± .7 ft. nominal dia. with mounting bracket; Test Features: add .5" (1.27 cm) to height for 1. Test port - Insert 0.1 inch maximum diameter allen thermal wrench or screwdriver into test port on detector Shipping Weight: 0.5 lb. (227 g) housing. Operating Temperature Range: 2. Test card - After removing detector cover, insert Thermal Models: 32°F to 100°F (0°C to 38°C) calibrated test card into test slot on screen. All Other Models: 32°F to 120°F (0°C to 49°C) 3. Test module - Using a standard voltmeter interface, Operating insert MOD40OR plug into detector's module port. Humidity Range: 10 - 93 % RH noncondensing Fulfills calibrated sensitivity test per NFPA 72. Air Velocity Rating: 3000 fpm Thermal Sensor Rating Wiring Gauge: 12 - 18 AWG, twisted pair (thermal models only): 135°F fixed temperature recommended Mounting: 3'/2" or 4" octagon box, 4" square box with plaster ring, 50, 60, 75 mm boxes Smoke Detector Spacing: Cr. smooth ceilings (as defined i.^. NFPA 72), spacing of 30 feet (900 sq. ft.) may be used as a guide. Other spacing may be used depending on ceiling height, high air movements, and other conditions or response requirements. restorable r. u` fiC FMEA ® approved ~ APPROVED 0 System Sensor 2/97 This document is not intended to be used for installation purposes. A05-194-03 General Description System Sensor 400 Series photoelectronic detectors are The 400 Series offer 6 different photoelectronic detectors specifically designed to meet the stringent performance with a variety of voltages, wiring configurations, and requirements of industrial and commercial fire detection/ thermal options. alarm systems. The design of these detectors emphasizes ease of installation and field maintenance. Eiectricai Specifications Control Operating Auxiliary Remote LED Current Consumption Model Product Panel Volta" Contacts Option Standby (max.) Alarm (max.) 2400 Photo Detector 2-wire 12/24 VDC No Yes 120 pA 2400TH Photo Detector w/Fixed Heat Sensor 2-wire 12/24VDC No Yes 120 AA 2412B Photo Detector 4-wire 12 VDC Yes No 120 µA 77mA 2412THB Photo Detector w/Fixed Heat Sensor 4-wire 12 VDC Yes No 120 µA 77mA 2424 Photo Detector 4-wire 24 VDC Yes No 120 pA 41mA 2424TH Photo Detector w/Fixed Heat Sensor 4-wire 24 VDC Yes No 120 pA 41mA * Must be limited by control panel Relay Contact Ratings: Resistive or inductive (60% power factor) load Alarm Contacts Form A: 2.0A p 30 VAC/DC Form C: 2.OA @ 30 VAC/DC 0.6A Q 110 VDC, LOA @ 125 VAC Reset Time: 3 sec. (max.) Startup Time: 34 sec. (max.) Engineering Specifications Smoke Detector shall be a photoelectronic type (model be easily removable for cleaning. It shall be possible to 2400, 2412, 2424) or a combination photoelectronic/ perform a sensitivity and functional test without the need thermal (model 2400TH, 2412TH, 2424TH) with thermal sensor rated at 135°F as manufactured by System Sensor. Wiring connections shall be made by means of SEMS screws. The detector will have a visible LED which will blink in standby and latch on in alarm. The detector shall have a nominal sensitivity of 3 % per foot as measured in the UL smoke box. The detector screen and cover should of generating smoke. Detector circuitry shall perform a self test on the sensing chamber and internal electronics every 40 seconds. If circuitry fails, the detector LED shall stop blinking. The detector shall have a mounting bracket that allows for mounting to a 31/2" or 4" octagon box or 4" square electrical box. Page 2 A05-194-03 400 Series Wiring Guide 2400/2400TH Wiring Diagram An-Tics 24 VDC EOL RELAY 2412B/THB,2424/TH Wiring Diagram Page 3 A05-194-03 I ' - - - - - - - - - - - - - - - - - - - OPTIONAL CLASS "A" LOOP - - - - - - - - - - - - - - - - - - - - - - - Ordering Information Part No. Description Accessories. Two-Wire Models A77-716B End of line relay for power supervision, 12/24 VDC 2400 Photoelectronic detector, 2-wire, 12/24 VDC RA40OZ Remote annunciator for 2 or 4 wire systems, 3-32V - 2400A Same as above, Canadian model 2400TH Photoelectronic detector, 2-wire, 12/24 VDC with built-in 1350F fixed heat sensor Four-Wire Models 2412B Photoelectronic detector, 4-wire, 12 VDC, with auxiliary contacts 2412BA Same as above, Canadian model 2412THB Photoelectronic detector, 4-wire, 12 VDC, with auxiliary contacts and integral 13S°F fixed heat sensor 2424 Photoelectronic detector, 4-wire, 24 VDC, with auxiliary contacts 2424TH Photoelectronic detector, 4-wire, 24 VDC, with auxiliary contacts and integral 1350F fixed heat sensor Use with ion and photo detectors. Fits standard U.S. single gang electrical box. (See below.) MOD40OR Detector sensitivity test module - Use with most analog or digital multimeters. Satisfies requirement of NFPA 72 for sensitivity testing. (See below.) RS24 Replacement insect screen for 2400, 241213, 2424 RS24T Replacement insect screen for 2400TH, 2412THB and 2424TH DUST45 Replacement protective dust cover for 400 Series The MOD40OR Field Sensitivity Test Module can be used with any standard DC voltmeter or muitimeter to check the sensitivity range of System Sensor's detectors (satisfies NFPA 72 requirement for sensitivity testing). RA40OZ Remote Annunciator, 3 - 32V Use with ion and photo detectors that have remote annunciator output 0 System Sensor Worldwide Manufacturing & Distribution in Canada: In the Far Fast: In Italy: Telephone: 905-812-0767 Telephone: 852-2191-9003 Telephone: 39-40-949011 Fax: 905-812-0771 Fax: 852-2736-6580 Fax: 39-40-382137 In China: Telephone: 86-29-524-6253 Fax: 86-29-524-6259 In India: Telefax: 91-11-5676815 In the United Kingdom: Telephone: 44-1403-276500 Fax: 44-1403-276501 Page 4 A05-194-03 February 18, 2000 F-800 ®Fire ~iTe®a~arms HD-boo Heat Detectors Section: Conventional Initiating Devices GENERAL The HD-600 Heat Detector is attractive, durable, and fea- tures combination rate-of-rise and fixed-temperature de- tectors. Heat detectors are available in 135°F (57°C) and 200°F (94°C) temperature ratings. Rate-of-rise elements detect heat by quickly responding to rapid temperature increase. HD-600 detectors use the same reliable pneumatic rate-of-rise element used in former models, but offer added aesthetic appeal. The pneumatic rate-of-rise element responds to a rapid rise in tempera- ture, approximately 15°F (8°C) per minute, by expansion of air within the sealed chamber faster than it can escape through a calibrated vent. The resultant increase in pres- sure depresses the diaphragm, causing the electrical con- tact to close the circuit. HD-600 rate-of-rise units have a wide spacing allowance of 50-foot (15.24-meter) centers. See Specifications table (page 2) for details. Fixed-temperature elements react to heat by responding to a specific temperature setting. The fixed-temperature element uses a fusible alloy. When activated, the external heat collector drops away to provide quick visual confirma- tion that the element has operated. The units protrude only 1-3/8" (34.925 mm) from the ceil- ing surface with a junction box mounting. They have pleas- ing contours and an all-white finish that conforms to ceiling aesthetics. FEATURES • Rate-of-rise and fixed-temperature. • One- or two-circuit, normally open. • Easy installation. • Low-profile design. • Visual indication. • Operation testing. INSTALLATION Each detector includes a patented reversible mounting plate. In one position, it easily attaches to a 3-1/4" (82.55 mm) octagonal box or 4" (101.60 mm) junction box. In reverse, the plate can be used for open wiring without a junction box. A 1/4" (6.35 mm) space between detector and mounting surface allows for wire connections. All mounting screws are concealed. The detector attaches simply to the mounting plate with a push and twist motion. No special tools are required. The mounting plate is molded of white self-extinguishing thermoplastic rated at 105°C. The plate is extremely strong, yet adapts to uneven mounting surfaces. California State Fire U` arsal 270-0075:168 DLC 7 LISTED ML361 (except HD622) M EA 52517 F M 250-94-E Approved 3-114" OR 4" OUTLET BOX MOUNTING OR 4" SQUARE BOX Cut for O surface mounting. REVERSIBLE O MOUNTING PLATE ® ai 8-32" 8-32" round head flat head SCREWS WOOD 518 to 1" SCREWS 0 0 JUNCTION BOX CEILING SURFACE MOUNTING MOUNTING 5075aial.xl This document is not intended be used for installation purposes. We try to keep our product all ' 0 900 information up-to-date and accurate. We cannot cover all specific applications or anticipate ate all requirements. All specifications are subject to change without notice. For more information, contact Fire•Lite Alarms, One Fire-Cite Place, Northford, Connecticut 06472. Phone: (800) 627-T_ - - 3473, Toll Free FAX: (877) 699-4105, FAX Back:(888) 388-3299 ENGINEERING U MANUFACTURING WEB: www.firelite.com n n 4-9/16" 2 1-31 HD-600 HD-600 SERIES TESTING METHODS • Models HD-601/HD-621 and HD-6021HD-622 can be tested by the application of quick heat from any convenient source. A portable hair dryer is recommended. However, do not apply heat that exceeds the fixed-temperature rating of the detector. • Models HD-603/HD-623 and HD-604/HD-624 cannot be tested. However, the fusible alloy element is generally con- sidered so reliable that testing is not necessary. SPECIFICATIONS 5075tLbl, 5075dotiwmf, 5075d0t2.wm[ 5075dot3.wM, 5075dnt4.wmf HD-601 & HD-621 HD-602 & HD-622 HD-603 & HD-623 HD-604 & HD-624 O O • O O O No marking. Gray ring. Gray spot. Black dot on white. Model HD-601 (one circuit) Model HD-602 (one circuit) Model HD-603 (one circuit) Model HD-604 (one circuit) Model HD-621 (dual circuit) Model HD-622 (dual circuit) Model HD-623 (dual circuit) Model HD-624 (dual circuit) Rate-of -rise and Rate-of -rise and Fixed-temperature only Fixed-temperature only fixed-temperature fixed-temperature 135 F (57 C). 200 F (94 C). 135 F (57 C). 200 F (94 C). Application: normal Application: normal Application: unusuallyviolent Application: unusually violent temperature fluctuations and temperature fluctuations and temperature fluctuations and temperature fluctuations and ceiling temperatures not ceiling temperatures ceiling temperatures not ceiling temperatures exceeding 100 F (38 C). exceeding 100 F (38 C) but exceeding 100 F (38 C). exceeding 100 F (38 C) but not 150 F (66 C). not 150 F (66 C). Maximum spacing allowance* Maximum spacing allowance* Maximum spacing allowance* Maximum spacing allowance* UL: 50 ft. x 50 ft. UL: 50 ft. x 50 ft. UL: 25 ft. x 25 ft. UL & FM: 15 ft. x 15 ft. (15.24 x 15.24 meters). (15.24 x 15.24 meters). (7.62 x 7.62 meters). (4.572 x 4.572 meters). FM: 30 ft. x 30 ft. FM: 30 ft. x 30 ft. FM: 20 ft. x 20 ft. (9.144 x 9.144 meters). (9.144 x 9.144 meters). (6.096 x 6.096 meters). *Refer to NFPA for application requirements. SCREW TERMINALS Standard Single-Circuit Detector Wire from alarm panel or previous detector. V~~ Dual-Circuit Detector Used to send two independent signals. Wire connected to next detector or end-of-line resistor. • Wire from alarm panel • or previous detector. u • NOTE: All single-circuit models come with one (1) normally open dry contact. 50751e,1.,mf Wire connected to next detector or end-of-line resistor. NOTE: All dual-circuit models come with two (2) normally open dry contacts. 50751.2. l NOTES Application: Heat detectors should be used for property protection. Reliance should not be placed solely on heat de- tectors for life safety. When life safety is involved, smoke detectors MUST also be used. Detectors must NOT be painted. Battery backup: Heat detectors should be electronically supervised with battery backup at the panel. Rate-of-rise mechanism: The rate-of- rise mechanism may be subject to re- duced sensitivity over time. Annual test- ing of the rate-of-rise operation is recom- mended. ELECTRICAL RATINGS • 6-125 Volts AC, 3.0 Amp. • 6-28 Volts DC, 1.0 Amp. • 125 Volts DC, 0.3 Amp. • 250 Volts DC, 0.1 Amp. Page 2 of 2 - DF-51375 Wire connected to next detector or end-of-line resistor. Commander3 Series Selectable Candela Evacuation Signals Applications The Commander3 Series is a low profile strobe or horn/strobe combination that offers dependable audible and visual alarms and the lowest current available. The GE3 Series 24VDC offers tamperproof field selectable candela options of 15, 30, 60, 75, and 110 candela. The 12VDC offers tamperproof field selectable candela options of 15, 30, 60, and 75 candela. The Commander3 Series horn offers a continuous or synchable temporal three in 2400Hz and mechanical tone, a chime as well as a whoop tone. All tones are easy for the professional to change in the field by using switches. The GE3 Series has a minimal operation current and has a minimum flash rate of 1 Hz regardless of input voltage. The Commander3 Series is shipped with the standard 4" mounting plate which incorporates the popular Super-SlideTM feature that allows the installer to easily test for supervision. The product also features a locking mechanism which secures the product to the bracket without any screws showing. The Commander3 also features the CheckmateTM - Instant Voltage Verification feature which allows the installer to check the voltage without removing the sig- nal. The GE3 Series appliances are UL 464 and UL 1971, listed for use with fire pro- tective systems and are warranted for three years from date of purchase. Standard Features • Nominal Voltage 12 & 24 VDC • 24 VDC units have field selectable candela options of 15, 30, 60, 75, and 110 candela • 12 VDC units have field selectable candela options of 15, 30, 60, and 75 candela • GEH horn is available in 12 or 24 Volt • Unit Dimensions: 5' high x 4.5" wide x 2.5" deep • Prewire Entire System, Then Install Your Signals • Super-SlideTM Bracket - Ease of Supervision Testing • CheckmateTM - Instant Voltage Verification • Lower Installation and Operating Costs • Input Terminals 12 to 18 AWG • Switch Selection for High or Low dBA • Switch for Chime, Whoop, Mechanical and 2400Hz Tone • Switch for Continuous or Temporal 3 (not available on whoop tone) • Tamperproof Re-entrant Grill GEC3/GES3 12 & 24 VDC SERIES Product Listings #~r ` c @ us L " 4:hN LYUNCEftnflRr35 Sh80flATOflIES, INC. • BFP (City of Chicago) • BS+AIMEA#285.91-E • CSFM 7135-0569:122 (GEC3-24 & GEH-24) 7125-0569:123 (GES3-24) 7125-0569:129 (GES3-12) 7135-0569:130 (GEC3-12 & GEH-12) • UL 464 & UL 1971 Listed • CAWULC S526-M87 Listed Product Compliance • NFPA 72 • Americans with Disabilities Act (ADA) ' MEMBER Sscwn,z,~;" nmll • Surface Mount with the GSB (Gentex Surface Mount Box) • Synchronize Strobe and/or Horn with AVSM Series Control Module (12 Volt product must use the AVSM Module). • Silence Horn While Strobes Remain Flashing • Wide Voltage Range 8-17.5 VDC (12 Volt Models) 16.33 VDC or FWR (24 Volt Models) • Faceplate Available in Red or Off-White GEH 12 or 24 Volt Low Profile Evacuation Horn Model Number art Number Nominal Voltage ever erant 10% Per UL 464, in nec otc oom dBA ~1 Oft. _=12-R 904-1239-00 ;2 bZ-tJ;e lUV - 7GrRTT-W_ 904-1241 --05 12 VDC 62-82 77F GEH24-R 0 - 05-00 4 - 00 GES3 12 or 24 Volt Selectable Candela Low Profile Evacuation Strobe Model Number art Number Nominal Voltage Candela (UL 1971) 3- 0 - 35-00 , 30, 0, 75 - TNM- 0 __90_TTLJ' 7-00 _ _ 15,30,60,75 3- 0 - 2 -0 1 TVDT 15, 0, 7 3- 0 - -00 , 3 0, - -0777 -00 5, 30, 60, 5, 110 3- 0 - 3 -00 5, 30, Q 75, 0 GES3-24PWH 904-1322-002 5, 0, 0, 75, 0 UIzti3-Z4l`VVVV 0 -1320-002 24 VDU 15, 30, 0, 75, 110 = Wall Mount = Red Faceplate = Off-White Faceplate = Plain (no lettering) Available with all models. These units are non-returnable. rat" bezel also available. GEC3 12 or 24 Volt Selectable Candela Low Profile Evacuation Horn/Strobe Model Number art Number Nominal Voltage Candela (UL 1971) Reverberant 1Oft Per UL 4641 In Anechoic Room dBA @ 10ft. - 5, 75 MTC_3-_f2VM_ 0 - 3 -002 5, 30, 0, 75 62-82 00 7 - 3- 0 - 3 -00 070, 75 -7573 7 62-82 00 3- 0 - 317-00 24 5, 30, 0, 75, 70 62-82 00 3- -M 0 - 3 - 5, 30, 0 1 - 6282 00 ,10, 11U 100 LiEC;3-24PVVVV 0 -131 -00 24 VLK; 15, 30, 0, 75, 10 2- 2 00 Notes: • The GE3 Series is not listed for outdoor use. • Operating temperature: 32°to 120oF (O° to 49° C). • For nominal and peak current across UL regulated voltage range for filtered DC power and unfiltered (FWR [Full Wave Rectified]) power, see installation manual. 12 volt models are DC only. • Gentex does not recommend using a coded or pulsing signaling circuit with any of our strobe products (see Technical Bulletin Number 014). Product Strobe Current Ratings an e a c c c uc Z4VUU m m m 7m Max m m m ;ItjMA Product Horn Current Ratings Horn Mode Minimum dBA @ 10ft. per UL464 (HIGH) Minimum dBA M 10ft. per UL464 (LOW) Regulated 24VDC Max. Operating rs High Setting (mA) emp z 7 Temp Mechanical 75 emp me 2 1 onhnuous z 7 7 2 onhnuous ec anica 7 7 Continuous Chime 63- 61* oop 16 1 7 5 GE3-24 Product Strobe Current Ratings 1 Candela c c m m Max 7 m ~ 1 7m m m "Operating the horn in this mode at this voltage will result in not meeting the minimum reverberant sound level required for public mode fire protection service. These settings are acceptable only for private mode fire alarm use. Use the high dBA setting for pub- lic mode application (not applicable when using the chime tone. The chime tone is always private mode). Notes: The sound output for the temporal 3 tone is rated lower since the time the horn is off is averaged into the sound output rating. While the horn is producing a tone in the temporal3 mode its sound pressure is the same as the continuous mode. To obtain the horn/strobe current draw, add the strobe current draw and the horn current draw. I The listed reverberant dSA are for the Continuous Tone mode. The Temporal 3 Tone has a reverberant dBA B 1011. per UL 464 is 77-83 with a horn current draw of 34mA. 2 RMS current ratings are per UL average RMS method. UL max current rating is the maximum RMS current within the listed voltage range (16-33VDC for 24VDC units) (8-17VDC for 12VDC units). For strobes the UL max current is usually at the minimum listed voltage (16VDC for 24VDC units) (BVDC for 12VDC units). For audibles the max current is usually at the maximum listed voltage. For unfiltered FWR ratings, see installation manual. Mounting Super Slide'" CD% Die Cast Metal Mounting Plate: Mounts to single gang, double gang 4p square boxes or GSB box. Checkmate' - Instant Voltage Verification 4~ C t The access holes are provided in the back of the terminal block to allow the voltage to be measured directly without removing the device. Typically this would be done at the end of the line to confirm design criteria. Most measure- ments will be taken using the S+ and S- locations although access is provided to other locations. NOTE: Care should be taken to not short the test probes. Switch Locations itch positions 1 and 2 the off position to select Jared horn antl strobe Her inputs. ON 1 2 3 4 5 6 Candela Selection Conventional GES3/GEC3 Series Wiring Diagrams SWITCH POSITION 3 4 5 tkdiankaFramp. ON ON ON Mechania4Can1. OFF ON ON FiJemp ON OFF ON HFCOm. OFF OFF ON Ch'r Temp. ON ON OFF Chlma Coni. OFF ON OFF Wnoop ON OFF OFF Wncap OFF OFF OFF Switch Position 6 JN> HIGH dB 7FF> LOW dB UL Listed UL Listed C t l Control on ro t Si nal i signal signal g g a Panel Panel S+ S+ S- H, H- H, H g+ S+ S- H+ H- S+ S+ S H. H- . supervised 0 I'll Supervised E) G Signal Circuit 1 Signal Circuit END OF LINE \ + - exESOis;o~nE RESISTOR exo ov uxe xE515TOR Wiring Diagram GE3 Series With Gentex Synchronization Module F.A.C.P. Note: See Technical Bulletin 015 for proper synchronization module for application. Note: When synchronizing the GE3 12 VDC Series, the AVSM synchronization module MUST be used. Architect & Engineering Specifications: The audible and/or visible signal shall be Gentex GE3 Series or approved equal and shall be listed by Underwriters Laboratories Inc. per UL 1971and/or UL 464. The notification appliance shall also be listed with the California State Fire Marshal (CSFM) and the Bureau of Standards and Appeals (NYC). The notification appliance (combination audible/visible) shall produce a peak sound output of 100dBA or greater at 12 or 24V as measured in an ane- choic chamber. The signaling appliance shall also have the capability to silence the audible signal while leaving the visible signal energized with the use of a single pair of power wires. Additionally, the user shall be able to select either continuous or temporal tone output with the temporal signal having the abil- ity to be synchronized. Unit shall be capable of being installed so that any unauthorized attempt to change the candela setting will result in a trouble signal at the fire alarm control panel. The audible/visible and visible signaling appliance shall also maintain a minimum flash rate of 1 Hz or up to 2 Hz regardless of power input voltage. The appliance shall have an operating current of 55mA or less at 24 VDC for the 15Cd strobe circuit and 106mA or less at 12 VDC for the 15Cd strobe circuit. The appliance shall be polarized to allow for electrical supervision of the system wiring. The unit shall be provided with a mounting bracket with termi- nals with barriers for input/output wiring and be able to mount to a single gang or double gang box or double workbox without the use of an adapter plate. The unit shall have an input voltage range of 16-33 volts with either direct current of full wave rectified power for 24 volt models or a voltage range of 8-17.5 volts for 12 volt models. The appliance shall be capable of testing supervision without disconnecting wires. Also the appliance shall be capable of mounting to a surface back box. The unit shall also be able to verify voltage at the unit without removing unit. 24 units per carton 28 pounds per carton GENTEX CORPORATION Fire Protection Products: vvww.gentex.com 10985 Chicago Drive Box 310 • Zeeland, Michigan 49464 616.392.7195 • 1.800.436.8391 • 616.392.4219 Fax Gentex corporation reservesthe right as make changes m the p adud data sheer, at their discretion. Important Ni Two. mabedals have been prepared by Game.G Momdonr'Gei for imormeblonal purposes only,are GE30201-12 mensecourc, summery, and ere Mt pu porletl to serve es lI advice and snoop not be used es such. Gentex me.'nes no representations and warmness, egaress or Implied, Nat these materials are amplete and accurate, up-tedate, or In campliame with all relevant local, able and federel laws, regulations and miss. The miens do not address all legal conspe dons as there ki Inevllale uncermi.9.01sg interpretation of laws, reglagons and rules and Me application of such laws, regulators am rules to prowl ubrfact patbems. Each person's activif s can lRerently aged the abllgations that exist under applicable lows, regulations or rules. Mundane, these materials should be used am, for infarmllorml purposes and slnuld not be used as a substlbbts far seeking profession legal advice. Gentex will not be responsible far any We or failure b of In realwae upon the IMotmatbn conmioe l in this earn e1NIL G Printed on Roo shed Paper a NOTICE AND ORDER To PROPERTY OWNER AND ALL CURRENT OCCUPANTS Pursuant to the 1997 Edition and the Uniform Code for the Abatement of Dangerous Buildings, the 1997 Uniform Housing Code and the 2003 International Property Maintenance Code, the following property is in violation. According to County Records you are the property owner of the described property in violation. pa„ t/d~o~ A7anuar~ 3,2007 ^y:'' r Certified Article Number Property Owner: Attn: Temenos Elder Care Company's 3901 9844 633$ 9432 3113 Teller Street Wheat Midge CO 80033 Certified Article Charles and Ellen Knapp 7j-.60-3-9-13n844 633$ 9456 305015 Street Boulder Colorado 80304 ucmmmmm~ All Current Occupants of Certified Article Number 3113 Teller Street 7160 3901 9844 6338 9449 Wheat Ridge CO 80033 IEEEMMM•-~~ Property Description: 064800 Barths. Block 1, Key 001-1, Section 26, Township 3, Range 69, SE quarter section or commonly known as: 3113 Teller Street. Wheat Ridge Colorado 80033 NOTICE The property owner, and all current occupants, are hereby notified that the undersigned Building Official of Wheat Ridge, Colorado, has found the building located on the above described real property to be a Dangerous Building within the meaning of Section 302 of the Uniform Code for the Abatement of Dangerous Buildings, 1997 edition, as adopted by the City of Wheat Ridge, Colorado ("Code'), as more particularly set out below: 5T/Z0 39Vd BNINNV7d L58Z9£Z£0£ 5T:GT L00Z/50/T0 The building is being used for dwelling purposes and is in violation of the Uniform Code for the Abatement of Dangerous Buildings, est ^ J- ~~P +>gsections that this xon v . I SECTION 301- GENERAL For the purpose of this code, certain terms, phrases, ords and their derivatives shall be construed as specified in either this chapter or as speced in the Bu' Code or the Housing Code. Where terms are not defined, they shall have their ordinary accepted within the context with which they are used. liebster's Third newlnternalional Dle#onory ajth;En5 fish Language. Unabridge, copyright 1986, shall be construed as providing ordinary accepted meaWords used in the singular masculine gender include the f ;nine and the feminne the masculineBUILDING CODE is the I'tuernaiional Code Council, as DANGEROUS BUILDING is any building or structure Section 302 of this code. HOUSING CODE is the Uniform Housing Code promo! Officials, as adopted. by this jurisdiction. INTERNATIONAL PROPERTY MAINTENANCE Maintenance Code promulgated by the International Code SECTION 302 -DANGEROUS BUILDING by this jurisdiction, to be dangerous under the provisions of by tho International Conference of building is the 2003 Intemational Property as adopted by this jurisdiction, For the purpose of this code, any building or structure which ~sss any or all of the conditions or defects hereinafter described shall be deemed to be a dangerous buil " , provided that such conditions or defects exist to the extent that the life, health, property or safety of the p lic or its occupants am endangered. L Whenever any door, aisle, passageway, stairway or tber r isaus of exit is not of sufficient width or size or is not so arranged as to provide saf and adequate means of exit in one of fire or panic. 2. Whenever the walking surface of any aisle, passagewa stairway or other means of exit is so warped, worn, Loose, torn or otherwise unsafe as to not p vide safe and adequate means of exit in case of fire or panic. 1 Whenever the stress in any materials, member or portion en more than one and one half tithes the working stress or s as new buildings of similar structure, purpose or location. 4. Whenever any portion thereof has been damaged by fire, art cause, to such an extent that the structural strength or stab ity before such catastrophe and is less than the minimum req ire. buildings of similar structure, purpose or location. 5. Whenever any portion or member or appurtenance t er detached or dislodged, or to collapse and thereby injure e 6. Whenever any portion of a building, or any member, a exterior thereof is not of sufficient strength or stability, or is n in place so as to be capable of resisting a wind pressure of one P, due to all dead and life loads, is allowcd in the Building Code for e, wind, flood or by any other f is materially less than it was of the Building Code for new f is fikely to fail, or to become ms or damage property. enance or ornamentation on the so red, attached or fastened If t specified in the building GT./FA ~eltlrl nNTNNVI,- JGR7GF.7.FAF GT.:GT. 2RA7./GA/T.A Code for new buildings of similar structure, purpose or location without exceeding the working stressed permitted in the B lding Code for such buildings. 7. Whenever any portion they f has wracked, warped, buckled or settled to such an extent that walls or other structural portions h ve materially less resistance to winds or earthquakes than is required in the case of similar new c truction. 8. Whenever the building or structure, or any portion thereof, because of (i) dilapidation, dete=rioration or decay; (ii)fa ty construction; (tit) the removal, movement or instability of any portion of the ground nee sary for the purpose of supporting such buildings; (iv) the deterioration, decay or insde I cy of its foundation; or (v) any other cause, is likely to partially or completely collapse. 9. Whenever, for any reason, t e building or structure, or any portion thereof, is manifestly unsafe for purpose of which i is being used. 10. Whenever the exterior walls other vertical structural members list, lean or buckle cc such an extent that a plumb line passin through the center of gravity does not fall inside the middle on third of the base. 11. Whenever the building or strut e, exclusive of the foundation, shows 33 percent or more damage or deterioration of its supporting member or members, or 50 percent damage or deterioration of its non-supporting members, enclos g or outside walls or coverings. 12. Whenever the building at strut: a has been so damaged by fire, wind, earthquake or flood, or has become so dilapidated or deteri aced as to become (i) an attractive tmisanec to children; (ii) a harbor for vaunts, criminals or or, oral persons; or as to (iii) enable persons to resort thereto for the purpose of committing unlaw 1 or immoral acts. 13. Whenever any building or s cture has been constructed, exists or is maintained in violation of any specific require ant or prohibition applicable to such building or structure provided by the building regula ns of this jurisdiction, as specified in the Building Code or Housing Code, or of any law r ordinance of this state or jurisdiction relating to the condition, location or structure o buildings. 14. Whenever any building or stmt a which, whether or not erected in accordance with a all applicable laws and ordinances, in any non-supporting part, member or portion less than 50 percent, or in any supporting part tuber or portion less the 66 percent or the (i) strength, (ii) fire-resisfug qualities or ehsracte stirs, or (iii) weather-resisting qualities or characteristics required by law in the case of anew y constructed building of like area, height and occupancy in the same location. 15. Whenever a budding or structure, us d or intended to be used far dwelling purposes, because of inadequate maintenance, dilapidati decay, damage, faulty construction or arrangement, inadequate light, air or sanitation fac • 'ties, or otherwise, is detemrined by the health officer to be unsanitary, unfit for human habitatio or in such a condition that is likely to cause sickness or disease. 16. Whenever any building or structure, b o damage, inadequate exists, lack of s c connections or hearing apparatus, or o hazard. 17. Whenever any building or structure is i to the common law or in equity jurisp 18. Whenever any portion or a building destruction of the building or structure c period in excess of six months so as to nuisance or hazard to the public, of obsolescence, dilapidated condition, deterioration, e fire-resistive construction, faulty electric wiring, gas cause, is determined by the fire marshal to be a fire a condition as to constitute a public nuisance known structure remains on a site after the demolition or whenever any building or structure is abandoned for a institute such building or portion thereof an attractive 9L/00 3DVd BNINNt1Id Lsazgez6oc 5S:5L L00Z/S0/L0 The 1997 Uniform Rousing Cedes states: SEMON 1001-DEPEWHONS 1001.1 General, Any heralding or p 'on thereof that is deternrined to be an unsafe building in accordance with Section 102 of We Building Co , or any building or portion thereof, including any dwelling unit, guest room or suite or rooms, or the p es on which the same is located in which there exists any nfthe section an extent that conditions referenced in this eudartgers tihe life, limb, health properly, safety ar welfare of the public or the occupants of, shall be deemed and hereby are d+clared to be s'ttbstandard buildings. 1001.2 Inadequate 5anihtt'en' Build' g: when they ate insanitary. Inadequate s 1. Lack of or improper water clo et 2. Lack of or improper water clo e hotel. 3. Lack of or improper kitchen s' 4. Lack of hot or cold running wa 3. Lack of hot or toll muting we 6. Lack of adequate heating facilitii 7. Lack of or improper operation S. Lack of minimum amounts of na 9. Room and space dimensions less 10. Lack of required electrical lighth 11. Dampness of habitable rooms. 12. Infestation of insects, vermin or t 13. General dilapidation or improper 14. Lack of connection to required se 15. Lack of adequate garbage and ru officer. or portions thereof shall be deemed substandard when they are tion shall include, but not be limited to, the following: lavatory, bathtub or shower in a dwelling unit or lodging house. , lavatories, and bathtubs or showers per number or guests in a in a dwelling unit. 'to plumbing fixtures in it hotel to plumbing fixtures in a dwelling unit or lodging house. required ventilating equipment. d light and ventilation require by this code. in required by this code, as determined by the health officer. disposal system. etorsga and removal facilities as determined by the health 10013 Structural Hazards. Buildings or pord thereof shall be deemed substandard when they are or contain stmt ural hazards. Structural hazards shall nclude, but not be limited to, the fallowing: 1. Deteriorated or inadequate foundations. 2. Defective or deteriorated flooring or floor s 3. Flooring or floor supports of insufficient siz 4. Members of walls, partitions or other vortica material or deteriorations. 5. Members of walls, partitions or other vert imposed loads with safety. 6. Members of ceilings, roofs, ceiling and roof or buckle due to detective material or deterim to carry imposed loads with safety. supports that split' lean, list or buckle do to defective supports that are of insufficient size to carry or other horizontal members that sag, split 9Tl50 39Vd 9NINNV-Id L58Z5EZ£0£ 9T:ST L00Z/50/T0 7. Members of ceilings, roo ceiling and roof supports, or other horizontal members that are of insufficient size to carry map sed lads with safety. 8. Fireplaces or cbimneys that t, bulge o settle due to defective material or deterioration. 9. Fireplaces or chimneys that c of insufficient size or strength to carry imposed loads with safety. 1001A Nuisance. Buildings or pi are deemed substandard buildings. 1001.5 Hazardous Electrical Wir requirements In effect at the time i generally accepted construction pr maintained in good condition or substandard. thereof in which there exists any nuisance as defined in this code Electrical wiring that was installed in violation of code allation or electrical wiring not installed lu accordance with t In areas where no codes were in effect or that has not been is not being used in a safe manner shall be considered 1001.6 Hazardous Plumbing. plumbingiat was installed in violation of code requirements in effect at the time of installation or plumbing not Installed in accordance with generally accepted construction practices in areas where no codes were in elect or that has not been maintained in good condition or that is not being used in a safe manner shall be c , idered substandard 1001.7 Hazardous Mechanical. Mecttht l equipment that was Installed in violation of code requirements in effect at the time of ins on or mechanical equipment not installed in accordance with generally accepted construction prs in areas where no codes were in effect or that has not been maintained in good condition or s not being u sed in a safe manner shall he considered substandard. 1001.8 Faulty Weather Protections. Bull when they have faulty weather protections 1. Deteriorated, crumbling or loose l 2. Deteriorated or ineffective were including broken windows or doe 3, Defective or lack of weather prof or weathering due to lack of paint 4. Broken, rotted, split or buckled ea lugs or portions thereof shall be considered substandard which shall include, but not be limited to, the following. or exterior walls, roof, foundations or floors, ion for exterior wall coverings, including lack of paint, other approved protective covering. for wall coverings or roof coverings. 1001.9 Fire Hazard. Any building or portion *=4 device, apparatus, equipment, combustible waste, or vegetation that, in the opinion of the chief of fire department, is in such a condition as to cause a fire or explosion or provide a ready fuel to augment th spread and intensity of fire or explosion arising from any cause shall be considered substandard. 1001.10 Faulty Materials of Construction. Tt~ use of materials of construction, except those that are specifically allowed or approved by this code the Building Code, and that have been adequately maintained in good and safe conditions, shall can a building to be substandard 1001.11 Hazardous or Insanitary premises. Tin matter, debris, garbage, offal, rat harborages, stage or conditions on a premises constitutes fire, health the procedures specified in Chapter 11 of this cede, 1001.12 Inadequate Exits. Except for these bu with adequate exit facilities conforming to the I whose exit facilities were installed in violation construction or whose exit facilities have not In increase in occupant load due to alterations, adt the time of construction shall be considered si requirements in effect at the time of their a considered substandard when the building of&t ccumulation of weeds, vegetation, junk, dead organic d water, combustible materials, and similar materials safety hazards that shall be abated in accordance with ngs or portions thereof that have been provided 4sions of this code, buildings or portions thereof code requirements in effect at the time of their increased in number or width In relations to any ms or change in use or occupancy subsequent to tandard. Notwithstanding compliance with code ruction, buildings or portions thereof shall be finds that an unsafe condition exists through an 9SJ90. 30Vd 9NINN1'l~d Y L58Z5CZE08 5I:5T L00Z/90(50 improper locati n of exits, a lack of an adequate number or width of exits, or when other conditions exist that are d serous to human life. 1001.13 Inadequa o Fire-Protection or Fire-Fighting Equipment. Buildings or portions there of shall be considered sub ndard when they are mat provided with the fire-resistive construction or fire- exiingttiahiug sys or equipment required by this code, except those buildings or portions thereof that conformed with all a licable laws at the time of their construction and whose fire-resistive integrity and fire-extinguishing sys or equipment has been adequately maintained and improved in relation to any increase in occupant 1 alteration or addition, or any change in occupancy. 1001.14 Improper Occpaney. All buildings or portions thereof occupied for living, sleeping, cooking or dining purposes th were not designed or intended to be used for such occupancies shall be considered substa¢dard V_ The fallowing is list of items Lt shall be fixed to 1. Bedroom windows do meet egress requirements of the Uniform Buildin ode or the International Building Code as required in S on 8310. 2. Minim equired width on the stairway does not meet code `~R Cry accor ' g to section R31 T.5.1. 3. N uilding permit was pulled for electrical work 4 oiler room needs make up air for combustion . Hot water shall not be hotter than 140 degrees. 6. GFCI needed in all bathrooms and kitchen outlets. 7. All exhaust fans must be vent to the outside and need to be working. 8. Ceiling of porch is sagging and is ready to fall down on occupants. Needs work to meet a 30lb snow load. 9. Several bedrooms do not have egress windows 10. Need handrail on stairways. 11. Bedrooms in basement have no egress windows. 12. Dryer vent is not to code. 13. Exterior stairs are not to code and are considered to be dangerous no rise shall be greater than 8" and a flight of stairs shall not exceed 12 feet in height without a landing. 14. No handrail to code on exterior stairs. 15. Stairs in basement do not meet code with no more than 3/8" difference between treads on a flight of stairs. 16. Chair lift' does not meet code. Must remove chair lift. Stair L width is to narrow for use of chair lift. This is a life safety issue Cade states minimum is 36" width. Exterior stairs are still covered with snow 5 days after last snow storm. 9Z/L0 39dd 9NINNVId L98Z9EZEOC 9S:9S L00Z/90/T0 ORDER ed mit The Building Official hall aCde property to be posted to prevent occup cy after March 30, 2007 and shall take action to remove all occupants from the g. IL Section in the Uniform Code for the Abatement of Danger Buildings states, " 801. ocedure. When anyiwork ofrepair..or.d tion`is td be;dorre pursuant Section. 3, Item 3, of ths,codethe bui .official slia11 issue ari The City of Wheat Ridge above to be a Dangerous to fix the deficient items.: by personnel of this Iurisdic director. Plans and specificatii the director may employ such contract basis as deemed reasc Official has determined the building The owners are ordered to pull a bui ublic works an a work shall be accomplished or by priva contract under the direction of said ere F y be prepared by said director, or al engineering assistance on a c 1y nec if any part of the work is to be accomplished by private tract, standard pt shall be followed." on 801,2 states, "801 1. The property owner to correct the follow 5T/80 39Vd for and obtain a City of Wheat Ridge SNINNVId L5839£Z£0£. 5T:9T L00Z/50/10 APPEAL OF THIS NOTICE AND ORDER Any person having record title or other legal interest in th above described premises may appeal this Notice and Order or any aotion of the Building fficial to the Building Code Advisory Board or known as the Board of Appeals pursu t to section 112 of the Code, provided that the appeal is made in writing as provided in a Code and filed with the Building Official wtthm ten (1i?)days &oms'1 rtat : of` ice iiftlus I~lotice and Order., 1GG WILE"MULic@. BY ORDER OF THE CITY OF WHEAT RIDGES BUILDING OFFICIAL 303-235-2853 303-570-7510 Chadley Root, Building Official 5L/60 30Vd SNINNtl-ld LGHSEZE0E 9L:5S L00Z/50/30 Property appraisal system General 21 -1 1'"1 IyE "r, m 4 Information Information Provio 2 OF 3 NgA Schedule: 021548 Parcel ID: 39-264-03-018 Status: Active Property Type: Apartment Property Address: 03113 TELLER ST WHEAT RIDGE CO 80033 Mailing Address: 03050 15TH ST BOULDER CO 80304 2614 Neighborhood: 261 - Subdivision Name: 064800 - HARTHE Page 1 of 1 Prjlit Owner I~ 65 KNAPP KNAPP 6164 Block Lot Key Section Township Range QoarterSection Land 001 0002 00H 26 3 69 SE 18121 LTotal 18121 Sale Date Sale Amount Deed Type Recept 08-10-1978 0 CONVE 06-01-1979 88,000 79049E 04-15-1997 89,000 Special Warranty Deed -Joint Tenancy F04Q1C Assessor Parcel Maps Associated with Schedule map39=264.pdf Acrobat Reader is required to view PDF's.. .'d '~!43tt@Y% Go to-As in la f.Qr this Schedule http://wwl4.co jeffersoli.co.as/ats/displaygeneral.do?suh=021548&otTset=1 1/3/2007 GT./RT. ~c147-I nNTNNV-1r1 - )gR7gP7FnR GT.:GT. 1817/GA/T.R HEALTH FACILITIES AND EMERGENCY ' ~ MEDICAL SRRVrCES DIVISION 4300'Cheny Creak Drive Soutb State Licerrsure Program w Denver, CO 30246 Assisted Living Residences Voice: 303-692-2300 Fax; 303.753.6214 0 www.cdphe.stam.co.us/hf/ht'd.asp Colorado 17epar went of Public Heahh andEnvimnmear Form: Sign off for Local Authorities FIRE DEPARTMENT Written evidence of compliance with local fire codes must he obtained Contact the city or county departments in your area and have The director or designee sign below or otherwise indicate approval Return ihisferm, signed by the proper authorities, to complete your license application. A final inspection cannot be conducted until these approvals are obtained A license cannot he issued until the completedform, with the original signature, is on file with the Dipislon, Name ofl7scility: Tem-eno5 4e/4r (a/'L Corr,=ny Address: 3/13 re/4r- 'S. r,ei" ljkee t- Riche je-/krr0,n Co rs0o33 No. of Licensed Beds Requested: 47 _ Name of person to Contact: Phone: ; _3 G4 Fax: , W1,ea „liar? FireDepatttnenthaving Jurisdiction: The above-named facility meets the requirements for fire safety, [ YES [ ] NO If "no" please explain oltR,gparate attachment or in the Comments section, below. Signature: hate Name of Person to Contact: Phone: f~ ! Fax: Address: • CODES} [ ] Application for anew license [ ] Change of Ownership [ ] Granting of a License [ ] New secured unit [ ] Name Change Change effective: Effective: Change effective: [ ] Increase/Decrease of Beds Change effective: From: to: If ] Action taken against the License [ ] Facility Closure [ ] Initial Notification to Zoning Dept. date: by: [ ] Final Notification to Zoning Dept date: h 9T/TT 39ttd 9NINNV Id Effective: L58Z5£Z£06 5T:5T L00Z150110 HEALTH FACILITIES AND EMERGENCY ~ MEDICAL SERVICES DIVISION 4300 Cherry Creek Drive South State Licensure Program Denver, 00 80246 Assisted Living Residences „ Voice: 303,692-2800 Fox; 303-753-6214 www.cdphe.s=.co.us/ht`hfd.asp CalerluloD FmuDeputinear Form: Sign off for Local Authorities ZONING DEPARTMENT Written epidence of compliance with local zoning codes and ordinances must be obtained Contact the clty or county departments in your area and have the director or designee sign below or otherwise indicate approvaL. Return this form, signed by the proper authorities to complete your license application. A final inspection' cannot be conducted nntd these approvals are obtained A license cannot be issued until the conWeled farm, with the ariginal signature, is on file with the Divislom Name of Facility: 74a-n44-lw E/carr Cefe ~a3r cr y ADDRESS: 3113 77-04j, S*,ee-t 1-e .4-1 ~'i ye J2.t{ers ar+ ~ d'do ~ No. of Liceased Beds Requested:' Name of Person to Contact: V C46 7 i ? ~A SV t f Phone: Q jay Fax: C_} Zoning Department having Jurisdiction: Wl, e4F R1 I SR Ito 2q6 672-0 The above named facthty.meets theregtiraments=fo zonigpproval_ Y]MS;:; [ ] NO If "no" please explain on a separate attachment. Name of Person to Contact: W_6W C f f k Phone: 60 -I - Address: € w pu a+ ELI ~2 ] Application for a new license ( ] Change of Ownership [ ] Granting of a License [ ] New secured unit [ ] Name Change Change effective: Effective: Change effective: ] Increase/1)ecrease of Beds Change effective: From: t0: [ ] Action taken against the License Effective: [ ] Facility Closure Effective: [ ] Initial Notification to Zoning Dept. date: • by: [ ] Final Notification to Zoning Dept dater by: _ qT./7T. --InIJ l RNTNNti-IH lGR7.GF.7F.AR ST:GT. lAR7/ciA/T.R c HEALTH FACILITIES AND EMERGENCY MEDICAL SERVICES DIVISION 4300 Cherry Creek Drive South State Lieensure PrOgram Denver. CO 80246 Assisted Living Residences Voice; 303-692-2800 Fax: 303-753-6214 www.odphe.staro. co.usrhflhfd.asp Form: Sign off for Local Authorities BUILDING DEPARTMENT Written evidence of compliance with local building codes must he obtained Contact the city or county departments in your area and have the director or designee sign below or otherwise indicate approval. Return rhisform, signed by the proper authorities, to camplete your license application. A final inspection cannot be conducted until these approvals are obtained A license cannot be issued until the completedform, with the original signature, is on file with the Division. Name of Facility: Tle ''1e rjcvzS 4 ~c i2,A' W @ COMP An V Address: 7-efieY 4JI.4Ad .Rjc♦.0 .J2744rSdh CC) &00,3 c:try ~.aumy No. of Licensed Beds Requested: 9' Name of person to Contact: c o r r s~+ ~v Phone:J 13'f Fax: L~ yAO Building Department having Jurisdiction: ! Jhe, t- Q4459 The above-named facility meets the requirements for building approval: G j YES [ ] NO If "no" please explain on a separate attachment. Signature Date: Name of Person to Contact: Phone: l ) _ ,lax: Address: USE ONLY-- [ ] Application for a new license [ ] Change of Ownership [ ] Granting of a License [ ] New secured unit [ ] Name Change Change effective: Effective: Change effective: [ ] increaselDecrease of Beds Change effective: From: tc [ ] Action taken against the License Effective: [ ] Facility Closure Effective: [ ] Initial Notification to Zoning Dept. date: _ by: -SWES 3998 . 9NINNV-ld LSKSEZE06 5L;52 L00Z/50/20 i Health Facilities and Emergency Medical Services Division 4300 Cherry Creek Drive South Denver, CO 80246 Voicc:303-642-2800 Fax: 303-753-6214 www. cdphe.state.eo.us/hf/hfd,asp e F State Licerisure Program ° Assisted Living Residences Cokuado Deparu3tmt of Public Health andEovironment FORM: FIRE CODE ATTESTATION: The Colorado Code of Regulations (6 CCR 1011-1), Chapter VII, 1.103(7)(d) requires that written proof be submitted to the Division documenting that your fine suppression or fire detection equipment has been tested by your local fire department or a registered fire suppression contractor. You may fulfill this requirement by submitting documentation of testing which is signed by a member of your local fire department or a registered fire suppression contractor or by signing the following attestation: ATTESTATION I hereby attest that I have met the requirements of 6 CCR 1011-1, Chapter VII, 1.103(7)(d) and can show proof that I have met this requirement should it lie requested of me by the Colorado Department of Public Health and Environment. (Signature of Facility Administrator/Owner) (Date) Attach the signed documentation of testing or the attestation to your application for a license or your renewal application. • Thank You. If you have any questions please call the Health Facilities and Emergency Medical Services Division Assisted Living Residence Support Staff at 303-692-2800. ST/VT 39Vcl y% 9NINNVId LSKSEZUE ST:GT L99d/99/7:0 0-5 a! gs in j; 4 dleii- ;a -i (j G wv~, caw Z;Wk e- 4-t f' a< eovg4m lctn O-:~> jl oilA ~,w MT 51rc~rbl'~r 4tim f k f~A ,cc Fcs I-eW ~3) Lb sv+ A, TIC uep ~TJ 014 ~f D i _ i t Y G. Z ,phi ~t.ti P ~ (/,A 010 lC'Gl c ~ 1 ' 02 AlrrGv,c.iy qrl~ i~~t GT./GT. _qcll7rl CINTNNttlrl /GR7qF.7F.RF. ci T.:GT 1RR71ciRIT.R AW 67rcl;5 t ti NOTICE AND ORDER To PROPERTY OWNER AND ALL CURRENT OCCUPANTS Pursuant to the 1997 Edition and the Uniform Code for the Abatement of Dangerous Buildings, the 1997 Uniform Housing Code and the 2003 International Property Maintenance Code, the following property is in violation. According to County Records you are the property owner of the described property in violation. January 3, 2007 =Maga Property Owner: Attn: Temenos Elder Care Company 7160 3901 9844 6338 9432 3113 Teller Street 01 ® • ° Wheat Ridge CO 80033 Charles and Ellen Knapp 3050 15th Street 7160 3901 9844 6338 9456. Boulder Colorado 80304 • ° All Current Occupants of 3113 Teller Street 7160 3901 9844 6338 9449 Wheat Ridge CO 80033 e •°a Property Description: 064800 Barths. Block 1, Key OOH, Section 26, Township 3, Range 69, SE quarter section or commonly known asc 3113 Teller Street.- Wheat Ridge Colorado 80033 NOTICE The property owner, and all current occupants, are hereby notified that the undersigned Building Official of Wheat Ridge, Colorado, has found the building located on the above described real property to be a Dangerous Building within the meaning of Section 302 of the Uniform Code for the Abatement of Dangerous Buildings, 1997 edition, as adopted by the City of Wheat Ridge, Colorado ("Code"), as more particularly set out below: The building is being used for dwelling purposes and is in violation of the Uniform Code for the Abatement of Dangerous Buildings, sections in bold are the sections that this property is in violation of. SECTION 301- GENERAL For the purpose of this code, certain terms, phrases, words and their derivatives shall be construed as specified in either this chapter or as specified in the Building Code or the Housing Code. Where terms are not defined, they shall have their ordinary accepted meanings within the context with which they are used. Webster's Third new International Dictionary of the English Language, Unabridge, copyright 1986, shall be construed as providing ordinary accepted meanings. Words used in the singular masculine gender include the feminine and the feminine the masculine. BUILDING CODE is the International Code Council, as adopted by this jurisdiction. DANGEROUS BUILDING is any building or structure deemed to be dangerous under the provisions of Section 302 of this code. HOUSING CODE is the Uniform Housing Code promulgated by the International Conference of building Officials, as adopted by this jurisdiction. INTERNATIONAL PROPERTY MAINTENANCE CODE is the 2003 International Property Maintenance Code promulgated by the International Code Council, as adopted by this jurisdiction. SECTION 302 - DANGEROUS BUILDING For the purpose of this code, any building or structure which has any or all of the conditions or defects hereinafter described shall be deemed to be a dangerous building, provided that such conditions or defects exist to the extent that the life, health, property or safety of the public or its occupants are endangered. 1. Whenever any door, aisle, passageway, stairway or other means of exit is not of sufficient width or size or is not so arranged as to provide safe and adequate means of exit in case of fire or panic. 2. Whenever the walking surface of any aisle, passageway, stairway or other means of exit is so warped, worn. Loose, tom or otherwise unsafe as to not provide safe and adequate means of exit in case of fire or panic. 3. Whenever the stress in any materials, member or portion thereof, due to all dead and life loads, is more than one and one half times the working stress or stresses allowed in the Building Code for new buildings of similar structure, purpose or location. 4. Whenever any portion thereof has been damaged by fire, earthquake, wind, flood or by any other cause, to such an extent that the structural strength or stability thereof is materially less than it was before such catastrophe and is less than the minimum requirements of the Building Code for new buildings of similar structure, purpose or location. 5. Whenever any portion or member or appurtenance thereof is likely to fail, or to become detached or dislodged, or to collapse and thereby injure persons or damage property. 6. Whenever any portion of a building, or any member, appurtenance or ornamentation on the exterior thereof is not of sufficient strength or stability, or is not so anchored, attached or fastened in place so as to be capable of resisting a wind pressure of one half of that specified in the building Code for new buildings of similar structure, purpose or location without exceeding the working stressed permitted in the Building Code for such buildings. 7. Whenever any portion thereof has wracked, warped, buckled or settled to such an extent that walls or other structural portions have materially less resistance to winds or earthquakes than is required in the case of similar new construction. 8. Whenever the building or structure, or any portion thereof, because of (i) dilapidation, deterioration or decay; (ii)faulty construction; (iii) the removal, movement or instability of any portion of the ground necessary for the purpose of supporting such buildings; (iv) the deterioration, decay or inadequacy of its foundation; or (v) any other cause, is likely to partially or completely collapse. 9. Whenever, for any reason, the building or structure, or any portion thereof, is manifestly unsafe for purpose of which it is being used. 10. Whenever the exterior walls or other vertical structural members list, lean or buckle to such an extent that a plumb line passing through the center of gravity does not fall inside the middle on third of the base. 11. Whenever the building or structure, exclusive of the foundation, shows 33 percent or more damage or deterioration of its supporting member or members, or 50 percent damage or deterioration of its non-supporting members, enclosing or outside walls or coverings. 12. Whenever the building or structure has been so damaged by fire, wind, earthquake or flood, or has become so dilapidated or deteriorated as to become (i) an attractive nuisance to children; (ii) a harbor for vagrants, criminals or immoral persons; or as to (iii) enable persons to resort thereto for the purpose of committing unlawful or immoral acts. 13. Whenever any building or structure has been constructed, exists or is maintained in violation of any specific requirement or prohibition applicable to such building or structure provided by the building regulations of this jurisdiction, as specified in the Building Code or Housing Code, or of any law or ordinance of this state or jurisdiction relating to the condition, location or structure of buildings. 14. Whenever any building or structure which, whether or not erected in accordance with a all applicable laws and ordinances, has in any non-supporting part, member or portion less than 50 percent, or in any supporting part, member or portion less the 66 percent or the (i) strength, (ii) fire-resisting qualities or characteristics, or (iii) weather-resisting qualities or characteristics required by law in the case of a newly constructed building of like area, height and occupancy in the same location. 15. Whenever a building or structure, used or intended to be used for dwelling purposes, because of inadequate maintenance, dilapidation, decay, damage, faulty construction or arrangement, inadequate light, air or sanitation facilities, or otherwise, is determined by the health officer to be unsanitary, unfit for human habitation or in such a condition that is likely to cause sickness or disease. 16. Whenever any building or structure, because of obsolescence, dilapidated condition, deterioration, damage, inadequate exists, lack of sufficient fire-resistive construction, faulty electric wiring, gas connections or heating apparatus, or other cause, is determined by the fire marshal to be a fire hazard. 17. Whenever any building or structure is in such a condition as to constitute a public nuisance known to the common law or in equity jurisprudence. 18. Whenever any portion or a building or structure remains on a site after the demolition or destruction of the building or structure or whenever any building or structure is abandoned for a period in excess of six months so as to constitute such building or portion thereof an attractive nuisance or hazard to the public. The 1997 Uniform Housing Codes states: SECTION 1001- DEFINITIONS 1001.1 General. Any building or portion thereof that is determined to be an unsafe building in accordance with Section 102 of the Building Code, or any building or portion thereof, including any dwelling unit, guest room or suite or rooms, or the premises on which the same is located, in which there exists any of the conditions referenced in this section to an extent that endangers the life, limb, health, property, safety or welfare of the public or the occupants thereof, shall be deemed and hereby are declared to be substandard buildings. 1001.2 Inadequate Sanitation. Buildings or portions thereof shall be deemed substandard when they are when they are in sanitary. Inadequate sanitation shall include, but not be limited to, the following: 1. Lack of or improper water closet, lavatory, bathtub or shower in a dwelling unit or lodging house. 2. Lack of or improper water closets, lavatories, and bathtubs or showers per number or guests in a hotel. 3. Lack of or improper kitchen sink in a dwelling unit. 4. Lack of hot or cold running water to plumbing fixtures in a hotel 5. Lack of hot or cold running water to plumbing fixtures in a dwelling unit or lodging house. 6. Lack of adequate heating facilities. 7. Lack of or improper operation or required ventilating equipment. 8. Lack of minimum amounts of natural light and ventilation require by this code. 9. Room and space dimensions less than required by this code. 10. Lack of required electrical lighting. 11. Dampness of habitable rooms. 12. Infestation of insects, vermin or rodents as determined by the health officer. 13. General dilapidation or improper maintenance. 14. Lack of connection to required sewage disposal system. 15. Lack of adequate garbage and rubbish storage and removal facilities as determined by the health officer. 10013 Structural Hazards. Buildings or portions thereof shall be deemed substandard when they are or contain structural hazards. Structural hazards shall include, but not be limited to, the following: 1. Deteriorated or inadequate foundations. 2. Defective or deteriorated flooring or floor supports. 3. Flooring or floor supports of insufficient size to carry imposed loads with safety. 4. Members of walls, partitions or other vertical supports that split, lean, list or buckle do to defective material or deteriorations. 5. Members of walls, partitions or other vertical supports that are of insufficient size to carry imposed loads with safety. 6. Members of ceilings, roofs, ceiling and roof supports, or other horizontal members that sag, split or buckle due to defective material or deterioration. 7. Members of ceilings, roofs, ceiling and roof supports, or other horizontal members that are of insufficient size to carry imposed lads with safety. 8. Fireplaces or chimneys that list, bulge o settle due to defective material or deterioration. 9. Fireplaces or chimneys that are of insufficient size or strength to cant' imposed loads with safety. 1001.4 Nuisance. Buildings or portions thereof in which there exists any nuisance as deemed in this code are deemed substandard buildings. 1001.5 Hazardous Electrical Wiring. Electrical wiring that was installed in violation of code requirements in effect at the time of installation or electrical wiring not installed in accordance with generally accepted construction practices in areas where no codes were in effect or that has not been maintained in good condition or that is not being used in a safe manner shall be considered substandard. 1001.6 Hazardous Plumbing. Plumbing that was installed in violation of code requirements in effect at the time of installation or plumbing not installed in accordance with generally accepted construction practices in areas where no codes were in effect or that has not been maintained in good condition or that is not being used in a safe manner shall be considered substandard. 1001.7 Hazardous Mechanical. Mechanical equipment that was installed in violation of code requirements in effect at the time of installation or mechanical equipment not installed in accordance with generally accepted construction practices in areas where no codes were in effect or that has not been maintained in good condition or that is not being used in a safe manner shall be considered substandard. 1001.8 Faulty Weather Protections. Buildings or portions thereof shall be considered substandard when they have faulty weather protections, which shall include, but not be limited to, the following: 1. Deteriorated, crumbling or loose plaster. 2. Deteriorated or ineffective waterproofing or exterior walls, roof, foundations or floors, including broken windows or doors. 3. Defective or lack of weather protection for exterior wall coverings, including lack of paint, or weathering due to lack of paint or other approved protective covering. 4. Broken, rotted, split or buckled exterior wall coverings or roof coverings. 1001.9 Fire Hazard. Any building or portion thereof, device, apparatus, equipment, combustible waste, or vegetation that, in the opinion of the chief of the fire department, is in such a condition as to cause a fire or explosion or provide a ready fuel to augment the spread and intensity of fire or explosion arising from any cause shall be considered substandard. 1001.10 Faulty Materials of Construction. The use of materials of construction, except those that are specifically allowed or approved by this code and the Building Code, and that have been adequately maintained in good and safe conditions, shall cause a building to be substandard. 1001.11 Hazardous or Insanitary Premises. The accumulation of weeds, vegetation, junk, dead organic matter, debris, garbage, offal, rat harborages, stagnant water, combustible materials, and similar materials or conditions on a premises constitutes fire, health or safety hazards that shall be abated in accordance with the procedures specified in Chapter 11 of this code. 1001.12 Inadequate Exits. Except for those buildings or portions thereof that have been provided with adequate exit facilities conforming to the provisions of this code, buildings or portions thereof whose exit facilities were installed in violation of code requirements in effect at the time of their construction or whose exit facilities have not been increased in number or width in relations to any increase in occupant load due to alterations, additions or change in use or occupancy subsequent to the time of construction shall be considered substandard. Notwithstanding compliance with code requirements in effect at the time of their construction, buildings or portions thereof shall be considered substandard when the building official finds that an unsafe condition exists through an improper location of exits, a lack of an adequate number or width of exits, or when other conditions exist that are dangerous to human life. 1001.13 Inadequate Fire-Protection or Fire-Fighting Equipment. Buildings or portions there of shall be considered substandard when they are not provided with the fire-resistive construction or fire- extinguishing systems or equipment required by this code, except those buildings or portions thereof that conformed with all applicable laws at the time of their construction and whose fire-resistive integrity and fire-extinguishing systems or equipment has been adequately maintained and improved in relation to any increase in occupant load, alteration or addition, or any change in occupancy. 1001.14 Improper Occupancy. All buildings or portions thereof occupied for living, sleeping, cooking or dining purposes that were not designed or intended to be used for such occupancies shall be considered substandard. The following is a list of items that shall be fixed to meet code. 1. Bedroom windows do not meet egress requirements of the Uniform Building Code or the International Building Code as required in Section R310. 2. Minimum required width on the stairway does not meet code according to section R311.5.1. 3. No Building Permit was pulled for electrical work 4. Boiler room needs make up air for combustion 5. Hot water shall not be hotter than 140 degrees. 6. GFCI needed in all bathrooms and kitchen outlets. 7. All exhaust fans must be vent to the outside and need to be working. 8. Ceiling of porch is sagging and is ready to fall down on occupants. Needs work to meet a 301b snow load. 9. Several bedrooms do not have egress windows 10. Need handrail on stairways. 11. Bedrooms in basement have no egress windows. 12. Dryer vent is not to code. 13. Exterior stairs are not to code and are considered to be dangerous no rise shall be greater than 8" and a flight of stairs shall not exceed 12 feet in height without a landing. 14. No handrail to code on exterior stairs. 15. Stairs in basement do not meet code with no more than 3/8" difference between treads on a flight of stairs. 16. Chair lift does not meet code. Must remove chair lift. Stair width is to narrow for use of chair lift. This is a life safety issue Code states minimum is 36" width. Exterior stairs are still covered with snow 5 days after last snow storm. 17. NOTE THERE MAYBE OTHER ITEMS THAT WERE NOT ADDRESSED. ORDER The City of Wheat Ridge Building Official has determined the building referenced above to be a Dangerous Building. The owners are ordered to pull a building permit to fix the deficient items. If such items are not fixed by February 12, 2007, the Building Department will post this building as a Dangerous Building. Pursuant to Code the property owner and all occupants are hereby ORDERED TO CEASE AND DESIST occupancy and use of the above described building. The Building Official shall cause the property to be posted with the attached Notice to prevent occupancy after March 30, 2007 and shall take action to remove all occupants from the building. 1. II. Section 801 in the Uniform Code for the Abatement of Dangerous Buildings states, " 801.1 Procedure. When any work of repair or demolition is to be done pursuant Section 701.3, Item 3, of this code, the building official shall issue an order thereof to the director of public works and the work shall be accomplished by personnel of this jurisdiction or by private contract under the direction of said director. Plans and specifications therefore may be prepared by said director, or the director may employ such architectural and engineering assistance on a contract basis as deemed reasonably necessary. If any part of the work is to be accomplished by private contract, standard public works contractual procedures shall be followed." Section 801.2 states, "801.2 Costs. The cost of such work shall be paid from the repair and demolition fund, and may be made a special assessment against the property involved, or may be made a personal obligation of the property owner, whichever the legislative body of this jurisdiction shall determine is appropriate." REMEDIAL ACTION 1. The property owner must apply for and obtain a City of Wheat Ridge building permit to correct the following deficiencies. III. All deficiencies shall be fixed but are not limited to the items on this list by February 12, 2007 or the Building Official shall cause the property to be posted with the attached Notice to prevent occupancy after March 30, 2007 and shall take action to remove all occupants from the building.. APPEAL OF THIS NOTICE AND ORDER Any person having record title or other legal interest in the above described premises may appeal this Notice and Order or any action of the Building Official to the Building Code Advisory Board or known as the Board of Appeals pursuant to section 112 of the Code, provided that the appeal is made in writing as provided in the Code and filed with the Building Official within ten (10) days from the date of service of this Notice and Order. Failure to appeal will constitute a waiver of all rights to an administrative hearing and determination of this matter. FILING OF AN APPEAL SHALL NOT STAY THE EFFECTIVENESS OF THIS NOTICE AND ORDER. It is a misdemeanor to occupy this building after March 30, 2007 or to remove or deface this notice. BY ORDER OF THE CITY OF WHEAT RIDGE'S BUILDING OFFICIAL 303-235-2853 303-570-7510 Chadley Root, Building Official 0 4 - w 1,4 ,krtcle- . aG?N1 111.. Ll I &ueec-,bi Y\j Jw ~ IN ~ (()L~wL Ato "ArcDA'l 1 0'4 ,Af6 51rdf Ut fi2l oq- AecO Lnoz7~- P410 bb ~l air a ~v<<:~ `7C,6 V6 0 eri16 moo/ ~x A v r-le.J rl ~ All, a~yL -x4 m NOTICE AND ORDER To PROPERTY OWNER AND ALL CURRENT OCCUPANTS January 3, 2007 Pursuant to the 1997 Edition of the Uniform Code for the Abatement of Dangerous Buildings, the 1997 Uniform Housing Code and the 2003 International Property Maintenance Code, the following property is in violation: Property Description: 064800 Barths. Block 1, Key OOH, Section 26, Township 3, Range 69, SE quarter section or commonly known as: 3113 Teller Street. Wheat Ridge Colorado 80033. According to County Records you are the property owner of the described property. Property Owner: Attn: Temenos Elder Care Company 3113 Teller Street Wheat Ridge CO 80033 Charles and Ellen Knapp 305015 Ih Street Boulder Colorado 80304 All Current Occupants of 3113 Teller Street Wheat Ridge CO 80033 NOTICE The property owner, and all current occupants, are hereby notified that the undersigned Building Official of Wheat Ridge, Colorado, has found the building located on the above described real property to be a Dangerous Building within the meaning of Section 302 of the Uniform Code for the Abatement of Dangerous Buildings and Section 1001 of the Uniform Housing Code both of the 1997 edition, as adopted by the City of Wheat Ridge, Colorado ("Code"), as more particularly set out below. The following is the list of items making the Building Dangerous and which shall be fixed to meet applicable codes: 1. Bedroom windows do not meet egress requirements of the Uniform Building Code or the International Building Code as required in Section R310. 2. Minimum required width on the stairway does not meet code according to section R311.5.1. 3. No Building Permit was pulled for electrical work 4. Boiler room needs make up air for combustion 5. Hot water shall not be hotter than 140 degrees this could scald a person if over 140 degrees. 6. GFCI needed in all bathrooms and kitchen outlets. 7. All exhaust fans must be vent to the outside and need to be working. 8. Ceiling of porch is sagging and is ready to fall down on occupants. Needs work to meet a 301b snow load. Add 2x4 as stated in several locations to support structure. 9. Several up stairs bedrooms do not have egress windows shall have 5.7 sq. ft. of open able space per code. Min of 20" opening. Current opening is only 19". 10. Need handrail on stairways. 11. Bedrooms in basement shall have egress windows along with living space. On or before February 12, 2007, bedroom egress windows shall be done or the owner shall have the tenant removed from basement. 12. Dryer vent is not to code must be metal duct behind walls and ceilings. 13. Exterior stairs are not to code and are considered to be dangerous no rise shall be greater than 8" and a flight of stairs shall not exceed 12 feet in height without a landing. 14. No handrail to code on exterior stairs. 15. Stairs in basement do not meet code with no more than 3/8" difference between treads on a flight of stairs. 16. Chair lift does not meet code. Must remove chair lift. By February 12, 2007 as stated in conversation of January 8, 2007. This is a life safety issue; Code states minimum is 36" width. ORDER The City of Wheat Ridge Building Official has determined the building referenced above to be a Dangerous Building. The owners are ordered to pull a building permit to fix the deficient items. If the deficient items are not fixed by February 12, 2007 or such later date as permitted by the Building Official, the Building Official will take steps under the Uniform Code for the Abatement of Dangerous Buildings to prevent occupancy after March 30, 2007 by posting the property to prevent occupancy and acting to remove all occupants from the building. APPEAL OF THIS NOTICE AND ORDER Any person having record title or other legal interest in the above described premises may appeal this Notice and Order or any action of the Building Official to the Building Code Advisory Board or known as the Board of Appeals pursuant to section 112 of the Code, provided that the appeal is made in writing as provided in the Code and filed with the Building Official within ten (10) days from the date of service of this Notice and Order. Failure to appeal will constitute a waiver of all rights to an administrative hearing and determination of this matter. FILING OF AN APPEAL SHALL NOT STAY THE EFFECTIVENESS OF THIS NOTICE AND ORDER. It is a misdemeanor to occupy this building after March 30, 2007 or to remove or deface this notice. BY ORDER OF THE CITY OF WHEAT RIDGE'S BUILDING OFFICIAL 303-235-2853 303-570-7510 Chadley Root, Building Official ~i ky 1 ,4 ~tTl p 1~ w y 'S a 1 4 8.,y~„ :w1w ~ mac tea, 11 1 Za1 1 f- _ . t ■ , Y„" t l.~ F/ F y i- 4 ~ u~'~"9n ,e t, e'{` . e t ~ I / 1i~ ~ 0 r t,. ~ kf ^ r . ~ r" -_n° + •1 t 2228 S'3twt t c 5 ~ N ` a ✓ 1t l~ t Utz tii , CU C > 4 ~ t i a t t, pt t tt tt~ttn;"`~4t1 ~t t n tt,w~t n:~\t li ~r fit{ t v t C<< 8 U flP ~ l~l l P1 ~ ,y.a s'~8~" kaaUX e cu a m. It d' ' n ao Rp x m n 8 ~ J`,