Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
11596 W 38th Place
**REVISION: Adding 20 squares of re -deck. Pitch: 4/12 *** CONTACTS *** OWNER (720)323-4260 SABELL G RICHARD *** PARCEL INFO *** ZONE CODE: UA / Unassigned USE: UA / Unassigned SUBDIVISION CODE: 2403 / APPLEWOOD VILLAGES, PROSPECT V BLOCK/LOT#: 0 / *** FEE SUMMARY *** ESTIMATED PROJECT VALUATION: 9,000.00 FEES Total Valuation 0.00 Use Tax 189.00 Permit Fee 188.45 ** TOTAL ** 377.45 *** COMMENTS *** *** CONDITIONS *** I, the property owner, by my signature, attest that I currently reside at the project property, intend to reside at the property for a period of one year after completion of the project, and am personally performing all work, without the assistance of hired or professional workers. If professionals are hired, those contractors are licensed with the City of Wheat Ridge and are listed on the permit. Consultations and inspections will only be performed with the homeowner of record present. midroof & Final Roof inspections for ROOFS 6/12 PITCH & OVER: 3rd party inspection will be required for both the midroof and final inspections. The 3rd party inspection report AND THE ORIGINAL PERMIT CARD needs to be dropped off to the Permit Desk at the City of Wheat Ridge. The report MUST BE SIGNED by the Homeowner. REGARDING ROOF VENTILATION: Roof ventilation shall comply with IBC Sec. 1203.2 or IRC Sec. R806. The installation of ridge venting requires the installation or existence of soffit venting. For calculation purposes, one hat or turtle vent equal to one-half of one square foot of opening. Effective December 1, 2014, asphalt shingle installations require an approved midroof inspection, conducted when 25-75% of the roof covering is installed, prior to final approval. Installation of roof sheathing (new or overlay) is required on the entire roof when spaced or board sheathing with ANY gap exceeding one half inch exists. Sheathing and mid -roofs may be called in at the same time, one hundred percent of the sheathing must be complete and 25-75% of the mid -roof may be complete. Asphalt shingles are required to be fastened to the roof deck with a minimum of 6 nails per shingle. Ice and water shield is required. Eave and rake metal is required. A ladder extending 3 feet above the roof eave and secured in place is required to be provided for all roof inspections. Roof ventilation is required to comply with applicable codes and/or manufacturer installation instructions, whichever is more stringent. In order to pass a final inspection of elastomeric or similar type roof coverings, a letter of inspection and approval from the manufacturer technical representative stating that "the application of the roof at (project address) has been applied in accordance with the installation instruction for (roof material brand name) roof City of Wheat Ridge 2 Homeowner Roof PERMIT - 201900568 _9r, PERMIT NO: 201900568 ISSUED: 04/01/2019 JOB ADDRESS: 11556 W 38th P1 EXPIRES: 03/31/2020 JOB DESCRIPTION: Homeowner re -roof with OC duration asphalt shingles. Squares: 20; Pitch: 3/12 **REVISION: Adding 20 squares of re -deck. Pitch: 4/12 *** CONTACTS *** OWNER (720)323-4260 SABELL G RICHARD *** PARCEL INFO *** ZONE CODE: UA / Unassigned USE: UA / Unassigned SUBDIVISION CODE: 2403 / APPLEWOOD VILLAGES, PROSPECT V BLOCK/LOT#: 0 / *** FEE SUMMARY *** ESTIMATED PROJECT VALUATION: 9,000.00 FEES Total Valuation 0.00 Use Tax 189.00 Permit Fee 188.45 ** TOTAL ** 377.45 *** COMMENTS *** *** CONDITIONS *** I, the property owner, by my signature, attest that I currently reside at the project property, intend to reside at the property for a period of one year after completion of the project, and am personally performing all work, without the assistance of hired or professional workers. If professionals are hired, those contractors are licensed with the City of Wheat Ridge and are listed on the permit. Consultations and inspections will only be performed with the homeowner of record present. midroof & Final Roof inspections for ROOFS 6/12 PITCH & OVER: 3rd party inspection will be required for both the midroof and final inspections. The 3rd party inspection report AND THE ORIGINAL PERMIT CARD needs to be dropped off to the Permit Desk at the City of Wheat Ridge. The report MUST BE SIGNED by the Homeowner. REGARDING ROOF VENTILATION: Roof ventilation shall comply with IBC Sec. 1203.2 or IRC Sec. R806. The installation of ridge venting requires the installation or existence of soffit venting. For calculation purposes, one hat or turtle vent equal to one-half of one square foot of opening. Effective December 1, 2014, asphalt shingle installations require an approved midroof inspection, conducted when 25-75% of the roof covering is installed, prior to final approval. Installation of roof sheathing (new or overlay) is required on the entire roof when spaced or board sheathing with ANY gap exceeding one half inch exists. Sheathing and mid -roofs may be called in at the same time, one hundred percent of the sheathing must be complete and 25-75% of the mid -roof may be complete. Asphalt shingles are required to be fastened to the roof deck with a minimum of 6 nails per shingle. Ice and water shield is required. Eave and rake metal is required. A ladder extending 3 feet above the roof eave and secured in place is required to be provided for all roof inspections. Roof ventilation is required to comply with applicable codes and/or manufacturer installation instructions, whichever is more stringent. In order to pass a final inspection of elastomeric or similar type roof coverings, a letter of inspection and approval from the manufacturer technical representative stating that "the application of the roof at (project address) has been applied in accordance with the installation instruction for (roof material brand name) roof Lva SSaxisne 9xIMorlriod 3HS x0IS03dsx2 Hod AVCI SSSxISnfi 7jgv wd65:TT As SQ w as IS= S'Lsanom aJeO luta33O 5utpling3atgj jo a.m ru2iS •uotloadsui plait of loofgns st 3I.tonJO Ipnoiddd •uotlotpstanf stgl jo uoilein-gai .to aauuutpio ' 103F ,Cut? Jo uotstnotd Xup jo uotlplotn ue `Jo lsnoidde ue jo `.toj ltuuod a aq of panilsuoo aq lou llugs ltttuod u jo But ei2 .to saotn_taSS uotloodsul pup �ij utpjing agI tuo3l.tom Bons3o Ipnotddu uollym Inogltnn �itom ivaouoo jo paaooid lou lipgs put!suotl5adSul ' [mgjo Xotlod pagstiquiso gltnn aoueptoaoe ui uotsintQ samloS uoiloadsul put? 2tupling aqI X3tlou llegs .taploq lnutad ag ' 'S nn ipnoaddp ogtoads puu j61ld Inogltaalenn jo mog 1pinluu agl jb a�ui?go a ui sllnsw llegs Izgl patuao3.tad aq Iit?gs .tauuuut AUVJO NlOtn ON 'b •paaluu.ten2 Jou st putt, iuiot gO 9uipiinq j5igD aqI jo uotlansip aios agl le si sliuuod pattdxa jo uotsualxa jo aoumssi-all 'I►tuuod nnau ,Cue Jo ltlnotddl ioj salnpaooid-put, saai sluaidblinbaa pirpuels aril of Ioafgns aq llugs Ituuad mou p3o aourtissl •pautzlgo aq of paimmi aq X ux Ituuad mau u `sa.ttdxa Ituuad stgl31 '£ aa3 Ittuta luuigi.to agl jo3luq-auo of lunbo aa3 u of loafgns aq x,ew pup iuloI 0 2uipimq joigD aql jo uoilaiosip agI Ju paluea2 aq oputu sAp pg i uugl aaotu ou jo uotsualxa ud •uotleitdxo jo SJpp agI of loild pantaaaa pita dutlpA ut apuut oq Isnut uotsualxa aoj slsanba2l •,Cltnilou Jo ssaiptOw aoumsst jo alep agI .tabu s* S9£ 3.1! X0 llugs Ituuad stq i, 'Z sampaooad puu satoiiod `suoiluln2ai `saoupuip• d `salnluls aiquotlddu lip puu `sluaumoop asogl gltnn aoui;tldtuoo agI of 13o ns st puu suotleogtoads pup supidd 2uiXuudtu000p puu uotfuotlddp Ituuadd agI ut poptnoid uotlpuuojut agI uo pasuq pansst suns Jttwad stq j ' I alpQ (auo ?IOIDV-dLNOO 10 XgNM0 Jo 31MBU21S •suotluogtoads pup sueld panotdde 2uiAuudtuo3op ,slt .toIKuu luitunoop stgl ut pasolostp st pauuo i ° 44 306m mug aq of )Ijonn agI of satytud se luamnoop stgl utglim patupu satltlua ilia apnput of pozi ioglnp Silu�a um I Iugl Isallp x Blinn uoilounfuoo ut panoadde pup pagtaosap jidnn oql uuo3.tad pup Itttua stgl utulgo ofpazttoglne aria puu ir4hdoad oRi jo pazuoglnu uaaq aneq io numo 1051 aqI tup I Iugl pup `sa.mpaup ootd psatatiod `sapoa ipddtotuntu aiquoilddu llp puu `sapoo rsuotJeogtoads pup suuld panoaddu uiXupdm000e Ile gltnn didutoo liugs pauuo3.tad aq of alionn aqI Ipgl Isallu Xgatag op uoTjoadsut ZPu?J Jo aWT! attq I2 agzs uo aq og paaznbaa st ,f5UTIan00 .h City of W heat i,ge COMMUNITY DEVELOPMENT Building & Inspection Services Division 7500 W. 29th Ave., Wheat Ridge, CO 80033 Office: 303-235-2855 * Fax: 303-237-8929 Inspection Line: 303-234-5933 Email: permits(d_)ci.wheatrid4e.co.us I FOR OFFICE USE ONLY Date: / r// Add to Permit # �o l I? 4f) Building Permit Revision/Amendment Application **" Please complete all highlighted areas on both sides of this form. Incomplete applications may not be processed. *** Property Address: I ���G Property Owner (please print): C2a;&40 Phone:�f2b s 3z3- 2Gz(� Property Owner Email: !-��\OQA �_ CCvvn_ti-5 . (V_V Mailing Address: (if different than property address) Address: City, State, Zip: Contact Person: Contractor: ; Contractors City License #: Contractor E-mail Address: Phone: Phone: Please Note: Additional valuation must include all general and subcontracted work to be performed related to the revisions and/or amendments declared in the description of work and which were not included in the original permit valuation. If revisions or amendments increase the original valuation, additional fees will be due at the time of approval. Depending on the scope of work, additional plan review fees may be due upon approval ($60.00 an hour - 2 hour minimum). Description of revised/amended work: Sq. FtJLF Y -- Amps 1� Btu's Gallons Squares z o Other 2 Additional Project Value: (Must include all general and subcontracted work to be performed related to revisions/amendments described above) $ OWNER/CONTRACTOR SIGNATURE OF UNDERSTANDING AND AGREEMENT I hereby certify that the setback distances proposed by this permit application are accurate and do not violate applicable ordinances, rules or regulations of the City of Wheat Ridge or covenants, easements or restrictions of record; that all measurements shown and allegations made are accurate; that I have read and agree to abide by all conditions printed on this application and that I assume full responsibility for compliance with applicable City of Wheat Ridge codes and ordinances for work under any permit issued based on this application; that I am the legal owner or have been authorized by the legal owner of the property to perform the described work and am also authorized by the legal owner of any entity included on this application to list that entity on this application. CIRCLE ONE:WNER) (CONTRACTOR) or (AUTHORIZE EPR SENT TIVE) of (OWNER) (CONTRACTOR) JPRINT NAIVIE��t U�p 1nAA,42A L,k\ SIGNATURE:2J DATE:' 1 =i r 1 DEPARTMENT USE ONLY ZONING COMMMENTS: Reviewer: BUILDING DEPARTMENT COMMENTS: Reviewer: PUBLIC WORKS COMMENTS: Reviewer: PROOF OF SUBMISSION FORMS Fire Department ❑ Received ❑ Not Required Water District ❑ Received ❑ Not Required Sanitation District ❑ Received ❑ Not Required OCCUPANCY CLASSIFICATION. Building Division Valuation: $ City of Wheat Ridge s Residential Sewer Repair PERMIT - 201802475 PERMIT NO: 201802475 ISSUED: 09/10/2018 JOB ADDRESS: 11596 W 38th P1 EXPIRES: 09/10/2019 JOB DESCRIPTION: 10 ft sewer repair in front yard, SDR, 35 pipe strongback coupling squeegee. *** CONTACTS *** OWNER (720)470-6061 ADAMSON MARK C SUB (303)287-9009 Brad Wakeham 130022 Trench Right LLC *** PARCEL INFO *** ZONE CODE: UA / Unassigned USE: UA / Unassigned SUBDIVISION CODE: 2403 / APPLEWOOD VILLAGES, PROSPECT V BLOCK/LOT#: 0 / *** FEE SUMMARY *** ESTIMATED PROJECT VALUATION: 5,800.00 FEES Total Valuation 0.00 Use Tax 121.80 Permit Fee 140.90 ** TOTAL ** 262.70 *** COMMENTS *** *** CONDITIONS *** ALL sewer repair/replacements for which a permit is issued MUST be inspected by and receive written approval from the City of Wheat Ridge BUILDING DIVISION, regardless of inspection by any Sanitation District representative. Inspection and approval of work by any Sanitation District representative DOES NOT grant authority to cover work without the approval of the Building Division. **For trenchless sewer replacements - The contractor will verify proper slope of new sewer piping in conformance with the IRC and IPC of 1/4 inch per foot unless otherwise allowed specifically by the applicable code. The plumbing contractor will provide verification of proper slope and drainage in writing as a condition of approval of the permitted work.** City of Wheat Ridge Residential Sewer Repair PERMIT - 201802475 PERMIT NO: 201802475 ISSUED: 09/10/2018 JOB ADDRESS: 11596 W 38th P1 EXPIRES: 09/10/2019 JOB DESCRIPTION: 10 ft sewer repair in front yard, SDR, 35 pipe strongback coupling squeegee. 11 by my signature, do hereby attest that the work to be performed shall comply with all accompanying approved plans and specifications, applicable building codes, and all applicable municipal codes, policies and procedures, and that I am the legal owner or have been authorized by the legal owner of the property and am authorized to obtain this permit and perform the work described and approved in conjunction with this permit. I further attest that I am leally authorized to include all entities named within this document as parties to the work to be performed and t t ork to be per ormed is disclosed in this document and/or its' accompanying approved plans and specifications. _Z_( V �� , /G, G Signat of WNER or CONTRACTOR (Circle one) Date I . T s permit was issued based on the information provided in the permit application and accompanying plans and specifications and is bject to the compliance with those documents, and all applicable statutes, ordinances, regulations, policies and procedures. 2. This permit shall expire 365 days after the date of issuance regardless of activity. Requests for extension must be made in writing and received prior to the date of expiration. An extension of no more than 180 days made be granted at the discretion of the Chief Building Official and maybe subject to a fee equal to one-half of the original permitfee. 3. If this permit expires, a new permit may be required to be obtained. issuance of a new permit shall be subject to the standard requirements. feesand_procedures for approval of any new permit. Re -issuance or extension of expired permits is at the sole discretion of the Chief Building Offcial and is not guaranteed. 4. No work of any manner shall be performed that shall results in a changeof the natural flow of water without prior and specific approval. 5. The permit holder shall notify the Building and Inspection Services Division in accordance with established policy of all required inspections and shall not proceed or conceal work without written approval of such work from the Building and Inspection Services Division. 6. The issuance or granting of a permit shall not be construed to be a permit for, or an approval of, any violation of any provision of any applicable code or ny ordinance or regulation of this jurisdiction. Approval of work is subject to field inspection. Si n hief EUding O ficial Date R TS MUST BE MADE BY 11 59PM ANY BUSINESS DAY FOR INSPECTION THE FOLLOWING BUSINESS DAY. 4a City of VV heat Ijd�� COMMUNITY DEVELOPMENT Building & Inspection Services Division 7500 W. 291h Ave., Wheat Ridge, CO 80033 Office: 303-235-2855 * Fax: 303-237-8929 Inspection Line: 303-234-5933 Email: permits(cDci.wheatridge.co.us FOR OFFICE USE ONLY Date: Plan/Permit/# Plan Review Fee: Building Permit Application *** Please complete all highlighted areas on both sides of this form. Incomplete applications may not be processed. *** Property Address: 115-& /Z 4T � �G Property Owner (please print): Zyze,e ��,¢�J�S�� Phone:zwG i'72f O6 p Property Owner Email: Tenant (Commercial Projects Only) Property Owner Mailing Address: (if different than property address) Address: City, State, Zip: Architect/Engineer E-mail: Phone: Contractor Name. - , ' City of Wheat Ridge License #: Phone: 30 Contractor E-mail Address:�!"0 �UC-�,� //k G'� eo For Plan Review Questions & Comments (please print): CONTACT NAME (please print):l! ' Phone: CONTACT EMAIL(p/ease print): Sub Contractors (Must provide Wheat Ridge License No.): Electrical: Plumbing: Mechanical: W.R. City License # W.R. City License # W.R. City License # Other City Licensed Sub: Other City Licensed Sub: City License # City License # ❑ COMMERCIAL RESIDENTIAL Description of work: For ALL projects, provide a detailed description of work to be performed, including current use of areas, proposed uses, square footage, existing condition and proposed new condition, appliance size and efficiency, type and amount of materials to be used, etc. Sq. FULF Amps BTUs Squares Gallons Commercial Projects Only: Occupancy Type: Construction Type: Occupancy Load: Project Value: (Contract value or the cost of all materials and labor included in the entire project) OWNEWCONTRACTOR SIGNATURE OF UNDERSTANDING AND AGREEMENT I hereby certify that the setback distances proposed by this permit application are accurate and do not violate applicable ordinances, rules or regulations of the City of Wheat Ridge or covenants, easements or restrictions of record. that all measurements shown and allegations made are accurate; that I have read and agree to abide by all conditions printed on this application and that I assume full responsibility for compliance with applicable City of Wheat Ridge codes and ordinances for work under any permit issued based on this application; that I am the legal owner or have been authorized by the legal owner of the property to perform the described work and am also authorized by the legal owner of any entity included on this application to list that entity on this application. I, the applicant for this building permit application, warrant the truthfulness of the information provided on t lication. CIRCLE ONE: (OWNER) Signature (first and last name): Printed Name: ZONING COMMMENTS: Reviewer: BUILDING DEPARTMENT COMMENTS: Reviewer: PUBLIC WORKS COMMENTS: Reviewer: (AUTHORIZEDREPRESENTATIVE)of (OWNER) (CONTRAC R) DATE: .� DEPARTMENT USE ONLY OCCUPANCY CLASSIFICATION: CONSTRUCTION TYPE: Building Division Valuation: i CITY,,OF WHEAT RIDGE A Building lnspecti6KDivision � (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE Inspection Type:-�'-('1i Job Address: 11SILP J' Permit Number: c;Z01 S -00q -7 ❑ No one available for inspection: Time l,'V)L/ AM PM Re -Inspection required: Yes (No When corrections have been made, call for re -inspection at 303-234-5933 Date:—q-f , l Inspector: - DO NOT REMOVE THIS NOTICE Occupancy/Type C 5 '1NSPECxQN RECO PECTION ONLINE FORM: tp://www.ci.wheatridge.co.us/inspectio INSPECTIO - J ncellations must be submitted via the online form before 8 a.m. the day of the inspection Inspections will not be performed unless this card is posted on the project site. "Request an inspection before 11:59 p.m. (midnight) to receive an inspection the following business day.** Inspector Must Sign ALL Spaces pertinent to this project Foundation Inspections Date Inspector Comments Initials Pier Concrete Encased Ground (CEG) �r Foundation / P.E. Letter Lath / Wall Tie Do Not Pour Concrete Prior To Approval Of The Above Inspections Underground/Slab Inspections Date Inspector., Initial Comments Electrical Wall Sheathing Sewer Service Plumbing �r Do Not Cover Underground or Below/In-Slab Work Prior To Approval Of The Above Inspections Rough Inspections Date Inspector Initials Comments Wall Sheathing Mid -Roof �r Lath / Wall Tie Rough Electric V7 0 r' Rough Plumbing/Gas Line _/ v Rough Mechanical f Rough Framing _ _ AV f/LI, Rough Grading Insulation Drywall Screw/ Nail Final Inspections Date filis ctor nitials Comments Landscaping & Parking / Planning Dept. Inspections from these entities should be requested one week in advance. For landscaping and parking inspections call 303-235-2846. For ROW and drainage inspections call 303-235-2861. For fire inspections contact the Fire Protection District for your project. ROW & Drainage / Public Works Dept. Floodplain Inspection (if applicable) Fire Inspection / Fire Protection Dist. Final Electrical :/ 4 & Final Plumbing Ig Final Mechanical s Roof Final Window/Doors Final Building 1-4 a0 _ /g NOTE: All items must be completed and approved by Planning, Public Works, Fire and Building before a Certificate of Occupancy is issued. Approval of the Final Building inspection does not constitute authorization of occupancy. "For low voltage permits — Please be sure that rough inspections are completed from the Fire District and electrical low voltage by the Building Division. Occupancy Is Not Permitted Until A Certificate of Occupancy Is Issued Protect This Card From The Weather i CITY OF WHEAT RIDGE _1�9�Building Inspection -Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE ) v m b t-/ 0 - 1 • i c, t % Inspection Type: LJ i 2 l= : r - Job Address: 2 - Permit Permit Number: ❑ No one available for inspection: Time 10 z3 7 (RVPM Re -Inspection required: Yes When corrections have been made, call for re -inspection at 303-234-5933 Date: Inspector: -TL DO NOT REMOVE THIS NOTICE -7 Q 0 - C-1-7 G - (o 0 & i CITY OF WHEAT RIDGE Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: 4031 f= F;/11,�d Job Address: % -3 14AF Permit Number: DO/ 70e7 S e" ❑ No one available for inspection: Time Re -Inspection required: Yes iP When corrections have been made, call for re -inspection at 303-234-5933 Date:/ F' % / Inspector: ��/� DO NOT REMOVE THIS NOTICE - i CITY OF WHEAT RIDGE Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: xai Job Address: 1?ZO Permit Number: 7Q -1156e ❑ No one available for inspection: Time J epm Re -Inspection required: Yes No When corrections have been made, call for re -inspection at 303-234-5933 or Date: 11 lo -%7 Inspector: � C?I O1 DO NOT REMOVE THIS NOTICE i CITY OF WHEAT RIDGE Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: Job Address: 115C7_6 Al Permit Number: Z-56 '/ 6 ❑ No one available for inspection: Timex' y02 M Re -Inspection required:( e�s No When corrections have been made call for re -inspection at 303-234-5933 Date://'�,/7 Inspector: �J DO NOT REMOVE THIS NOTICE i CITY OF WHEAT RIDGE Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION 1 �}NOTICE � j Inspection Type: `IIF & )a �� �'�-i W Job Address: ❑ No one available for inspection: Time G� M Re -Inspection required: �esl\lo When corrections have been made, call for re-inspection at 303 -234 - Date: 1 `F'1 7 Inspector: DO NOT REMOVE THIS NOTICE i CITY OF WHEAT RIDGE Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax Inspection Type: INSPECTION puv,s NOTICE ❑ No one available for inspection- Time V AM/PM Re -Inspection required: Ye No When corrections have been made, call for re-inspae9 ' ction at 303-234-5933 Dater- l Inspector:% �J DO NOT REMOVE THIS NOTICE i CITY OF WHEAT RIDGE _:�9rBuilding Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: �� 1-->4 Job Address: Permit Number: ❑ No one available for inspection: Time AM/PM Re -Inspection required: Yes/No) No oe When corrections have been made, call for re -in spe i at 303-234-5933 /.— Date: Inspector: %. i City of Wheat Ridge R � Residential Remodel PERMIT - 201704568 PERMIT NO: 201704568 ISSUED: 08/31/2017 JOB ADDRESS: 11596 W 38th PL EXPIRES: 08/31/2018 JOB DESCRIPTION: Demo and remodel kitchen, bath and laundry room - 482 sq ft *** CONTACTS *** OWNER (303)422-2792 ADAMSON MARK C & KIM GC (303)514-9999 Dan Foster 018639 The Craftsmen Inc. SUB (303)202-1066 Donn Botzum 060232 Donn Botzum Services SUB (303)761-0630 Tim Schenkelberg 060226 DG&S Electric Service SUB (720)870-1580 Dean Peterson 022447 Summit Heating & A/C Inc. *** PARCEL INFO *** ZONE CODE: UA / Unassigned USE: UA / Unassigned SUBDIVISION CODE: 2403 / APPLEWOOD VILLAGES, PROSPECT V BLOCK/LOT#: 0 / *** FEE SUMMARY *** Total Valuation Plan Review Fee Use Tax Permit Fee ** TOTAL ** *** COMMENTS *** ESTIMATED PROJECT VALUATION FEES 0.00 406.93 860.16 626.05 1,893.14 40,960.00 *** CONDITIONS *** Approved per plans and red -line notes on plans. Must comply with 2012 IRC, 2014 NEC and all applicable City of Wheat Ridge Municipal Codes. Work is subject to field inspections.All roughs to be done at Framing Inspection. City of Wheat Ridge Residential Remodel PERMIT - 201704568 PERMIT NO: 201704568 ISSUED: 08/31/2017 JOB ADDRESS: 11596 W 38th PL EXPIRES: 08/31/2018 JOB DESCRIPTION: Demo and remodel kitchen, bath and laundry room - 482 sq ft I, by my signature, do hereby attest that the work to be performed shall comply with all accompanying approved plans and specifications, applicable building codes, and all applicable municipal codes, policies and procedures, and that I am the legal owner or have been authorized by the legal owner of the property and am authorized to obtain this permit and perform the work described and approved in conjunction with this_permit. I further attest that I am legally authorized to include all entities named within this document as parties to the work to be performed and that all wo be performed is disclosed in this document and/or its' accompanying approved plans and specifications. signature of OWNER or CONTRACTOR (Circle one) Date 1. This permit was issued based on the information provided in the permit application and accompanying plans and specifications and is subject to the compliance with those documents, and all applicable statutes, ordinances, regulations, policies and procedures. 2. This permit shall expire 365 days after the date of issuance regardless of activity. Requests for extension must be made in writing and received prormto the date of expiration. An extension of no more than 180 days made be granted at the discretion of the Chief Building Official and ay be subject to a fee equal to one-half of the original permit fee. 3. If this permit expires, a new permit may be reyired to be obtained. Issuance of a new permit shall be subject to the standard requirements, fees and procedures for approval of any new permit. Re -issuance or extension of expired permits is at the sole discretion of the Chief Building Offial and is not guaranteed. 4. No work of any manner shall be performed that shall results in a change of the natural flow of water without prior and specific approval. 5. The permit holder shall notify the Building and Inspection Services Division in accordance with established policy of all required inspections and shall not proceed or conceal work without written approval of such work from the Building and Inspection Services Division. 6. The issuance or granting of a.permit shall not be construed to be a permit for, or an approval of, an violation of any provision of any applicable code or any ordinance or regulation of this jurisdiction. Apprav work is subject to field inspection. • Signature of Chief Building Official Date REQUESTS MUST BE MADE BY 11:59PM ANY BUSINESS DAY FOR INSPECTION THE FOLLOWING BUSINESS DAY. City of �W heat�id�e MUNiTY DEVELOPMENT Building & Inspection Services Division 7500 W. 291h Ave., Wheat Ridge, CO 80033 Office: 303-235-2855 * Fax: 303-237-8929 Inspection Line: 303-234-5933 Email: permits(cD.ci.wheatridge.co.us FOR OFFICE USE ONLY Date: �IA I) "I Plan/Permit# 1 )0100� Plan Review Fee: Building Permit ApplicationPA I *** Please complete all highlighted areas on both sides of this form. Incomplete applications may not be processed. *** Property Address: I (5-6f v 1k)eg+ -?6 PL�� Property Owner (please print): i` ehf'� 4-)'-#'w, A J a�,t s o vt Phone: 303 —2 � Property Owner Email: b Irl ea..VyLboma- Ri Clew%C-4U 4i . V AA Mailing Address: (if different than property address) Address State, Architect/Engineer: Architect/Engineer E-mail: Phone: Contractor: T 1%,e-, G vZ . Contractors City License #: ( ( , 4_ � Phone: 30'3. 5 Contractor E-mail Address: -rkzc 11k 9 wt .t l gz c o _114 Sulo Contractors: Electrical: 47&'K SLECTRIc5RV144 Plumbing: Dov"I W5'4 ^ '5tiwiccS Mechanical: SJMMtT Af4g1IJfr W.R. City License # O � o fJ4 W.R. City License # 400713:z W.R. City License # /00 A(c�- a 2z 1-7 Other City Licensed Sub: City License # Other City Licensed Sub: City License # Complete all information on BOTH sides of this form ❑ COMMERCIAL RESIDENTIAL Description of work: (Check all that apply) ❑ NEW COMMERCIAL STRUCTURE ❑ ELECTRICAL SERVICE UPGRADE ❑ NEW RESIDENTIAL STRUCTURE ❑ COMMERCIAL ROOFING ❑ COMMERCIAL ADDITION ❑ RESIDENTIAL ROOFING ❑ RESDENTIAL ADDITION ❑ WINDOW REPLACEMENT ❑ COMMERCIAL ACCESSORY STRUCTURE (Garage, shed, deck, etc.) ❑ RESIDENTIAL ACCESSORY STRUCTURE (Garage, shed, deck, etc.) ❑ MECHANICAL SYSTEM/APPLIANCE REPAIR or REPLACEMENT ❑ PLUMBING SYSTEM/APPLIANCE REPAIR or REPLACMENT ❑ ELECTRICAL SYSTEM/APPLIANCE REPAIR or REPLACEMENT ❑ OTHER (Describe) B iwo a 6(- P I Trc.ti a- Z A-ni (For ALL projects, please provide a detailed description of work to be performed, including current use of areas, proposed uses, square footage, existing condition and proposed new condition, appliance size and efficiency, type and amount of materials to be used, etc.) � ► ,fig ► c,"t N � / RZ01Q4 K � x t S n N fs S► h1 cA�s t�1' Z $TVg 0`F>rU1� AT C,TcEE16-M F-y�)T'(Lq 2 WAW5 A'T Po,.4DVZ- [—,D tM2EF7244044;-.. pot. -s DSL Zao M 'T -e, S t -t c. t{ Tt j S M AV -E-0- '5 t zf , .1 �ll� nil (.� I U>iv"1 Ca J NT S, -YAi,E- Rock AT poWDJ42_ r��r�, l-t-rCt( t P�,,Jt)6,(T- (�bewX 51 n1yfiq--sc.cT5, a2ELXF- aL s -n O (- )J f-tZ o A V- � i t L -IF- P to a fZ S ((k-PWkCJ 2- 1'f7-F?,Q4 o (2 - pod R S vs/ k E w, I NS rA�L nF-W gAVK D P P P-11 m 0�1- W AS N 'iv ts, 1Z6 W e 6-'f S .rPP L-1 AtrL J c t uToZk ItTT 'tZ f_517 -F -Q PpvJ Dk4k- {:-e• vt�. Sq. Ft./LF L -0-5S t V( rnv !I t Z. SF Btu's Amps Squares Gallons Other Project Value: (Contract value or the cost of all materials and labor included in the entire project) OWNER/CONTRACTOR SIGNATURE OF UNDERSTANDING AND AGREEMENT I hereby certify that the setback distances proposed by this permit application are accurate and do not violate applicable ordinances, rules or regulations of the City of Wheat Ridge or covenants, easements or restrictions of record; that all measurements shown and allegations made are accurate; that I have read and agree to abide by all conditions printed on this application and that I assume full responsibility for compliance with applicable City of Wheat Ridge codes and ordinances for work under any permit issued based on this application; that I am the legal owner or have been authorized by the legal owner of the property to perform the described work and am also authorized by the legal owner of any entity included on this application to list th ti ty on this application. CIRCLE ONE: (OWNER) (CONTRACTOR) or(AUTHORIZED REPRESENTATIVE) ,of(O(OWNER) (CONTRACTOR) '% PRINT NAME: t) AC t�4 '2 D 5 7*6 /�--- SIGNATURE: (_/�/� \ I ! t `� v DATE: 14 — ( ` ZONING COMMMENTS: Reviewer: BUILDING DEPARTMENT COMMENTS: Reviewer: PUBLIC WORKS COMMENTS: Reviewer: PROOF OF SUBMISSION FORMS Fire Department ❑ Received ❑ Not Required Water District ❑ Received ❑ Not Required Sanitation District ❑ Received ❑ Not Required DEPARTMENT USE ONLY OCCUPANCY CLASSIFICATION: TYPE OF CONSTRUCTION: SPRINKLERED: OCCUPANTLOAD: Building Division Valuation: $ C?/E5 IM u0slpeW `APAAtlaeCjuea!JaWV 0009 'Awed W0D aDue.tnsul ap I Allwe- ,JL:)pawV `sa4eilylV sli q Auedl-uoD a�)ut?lnsul lenln" AllLue j ueziu airy CERTIFICATE OF LIABILITY INSURANCE American Family Insurance Company ❑ American Family Mutual Insurance Company if selection box is not checked. 6000 American Pky Madison, Wisconsin 53763-0001 Insured's Name and Address Agents Name, Address and Phone Number (Agt./Dist.) Summit Heating & Air Conditioning Inc Kevin Lee Freidig 7966 E Sundance Trl 10288 W CHATFIELD AVE STE 302 Parker, CO 80138 LITTLETON, CO 80127 (303) 932-6333 (165/308) This certificate is issued as a matter of information only and confers no rights upon the Certificate Holder. This certificate does not amend, extend or atter the coverage afforded by the policies listed below. This is to certify that policies of insurance listed below have been issued to the insured named above for the policy penod indicated, notwithstanding any requirement, term or condition of any contractor other document with respect to which this certificate may be issued or may pertain, the insurance afforded by the policies described herein is subject to all the terms, exclusions, and conditions of such poiicies. CANCELLATION City of Wheatridge POLICY DATE 7500 West 29th Ave TYPE OF INSURANCE POLICY NUMBER LIMITS OF LIABILITY EFFECTIVE EXPIRATION upon the company, Its agents or representatives -10 days unless different number of days (Mo, aY, Yr) (Mo, Day, Yr) Homeowners/ subject to cancellation in conformity with their terms and by the laws of the state of issue. Bodily Injury and Property Damage Mobilehomeownem Liability 08/31/2017 Ellen Bruns U-201 Ed- 5100 Stock No. 06668 Rev. 7/02 Each Occurrence $ ,000 Boatowners Liability Bodily Injury and Property Damage Each Occurrence $ 000 Personal Umbrella Liability Bodily Injury aid Property Damage Each Occurrence $ GO0 Farm Liability & Personal Liability Farm/Ranch Liability Each Occurrence $ ,000 Farm Employer's Liability Each Occurrence $ ,000 Statutory — WorkersCompensation and 05XY074493 0612412017 06/24/2018 Each Accident $ 1,000,000 Disease - Each Employee $ 1,000,000 Employers Liability t Disease -Policy Limit $ 1,000,000 General Liability General Aggregate $ 2,000,400 Products - Completed Operations Aggregate $ ,000 X ❑ Commercial General Liability (occurrence) 05-XD1705-09 06/24/2017 06/24/2018 Personal and Advertising Injury $ 1,000,000 Each occurrence $ 1.000,400 ❑ ❑ Damage to Premises Rented to You $ 100,000 Medical Expense (Any One Person) $ 10.000 Businessowners Liability Each Occurrencett $ .044 Aggregatett $ .044 Liquor Liability Common Cause Limit $ 000 Aggregate Limit $ ,000 Automobile Liability Bodily Injury- Each Person $ 1,000:040 ❑ Any Auto ❑ All Owned Autos Bodily Injury -Each Accident $ 1 ,000, 444 Property Damage $ 1,000,000 D Scheduled Autos 05XD170510 06/24/2017 06/24/2018 Hired Auto Bodily Injury and Property Damage Combined $ ,000 1K Nonowned Autos Excess Liability ❑ Commercial Blanket Excess Each Occurren efAggregate $ ,000 Other (Miscellaneous Coverages) DESCRIPTION OF OPERATIONS / LOCATIONS! VEHICLES / RESTRICTIONS/ SPECIAL ITEMS tThe individual or partners ❑ Have shown as insured elected to be covered under this policy. ❑ Have not ttProducts-Completed Operations aggregate is equal to each occurrence limit and is included in policy aggregate. CERTIFICATE HOLDER'S NAME AND ADDRESS CANCELLATION City of Wheatridge Should any of the above described policies be cancelled before the expiration date 7500 West 29th Ave thereof, the company will endeavor to mail '( days) written notice to the Certificate Wneatroge Cd 80033 Holder named, but failure to mail such notice shall impose no obligation or liability of any kind upon the company, Its agents or representatives -10 days unless different number of days shown. x This certifies coverage on the date of issue only. The above described policies are subject to cancellation in conformity with their terms and by the laws of the state of issue. DATE ISSUED AUTHORIZED REPRESENTATIVE 08/31/2017 Ellen Bruns U-201 Ed- 5100 Stock No. 06668 Rev. 7/02 otv� j City ®f ea i le ice'"Commu-NtTx DFvnc�pkl]Er�T City of Wheat Ridge Municipal Building 7500 W. 29b Ave. Wheat Ridge, CO 80033-8001 P: 303.235.2855 F: 303.237.8929 Review is limited to the contents of the plans submitted and any errors or omissions contained herein shall not be construed as permission to allow any conditions to exist in violation of the codes of the City of Wheat Ridge 3 Burial depth requirements: Electrical - direct burial conductors shall be a minimum of 24 -inches deep, non-metallic conduit 18 -inches deep or 24 - inches under driveways. (IRC Table E3803.1) Water Lines - shall be a minimum of 36 -inches deep. (IRC P2603.6) Gas Service Piping - installed a minimum of 12 -inches below grade or 8 -inches below grade where serving individual outside appliances. An 18 AWG yellow insulated tracer wire must be installed adjacent to underground nonmetallic gas piping and terminate above grade at each end. (IRC G2415.1.2 and G2415.17.3) 4 Underground plumbing pipe shall have a solid and continuous load-bearing support. Piping cannot bear on rocks. Pipes passing under a footing or through foundation wall shall be provided with a relieving arch or a sleeve. Trenches parallel tc footing shall not extend below the 45* plane of the edge of the footing. Water piping must be buried a minimum 36 - inches deep. Water service pipe may be installed in the same trench as the building sewer provided the sewer pipe material is listed for underground use within the building or the water service pipe is separated from the sewer by a minimum distance of 5 -feet horizontally or elevated at least 12 -inches above and to one side of the sewer line. 5 Frost depth to the bottom of the foundation footings must be as noted on the engineered plans. If not noted, the frost depth to the bottom of the footings must be a minimum of 30 -inches below finished grade. (IRC TableR301.2.1) 6 Caisson and helical pier foundations will not be inspected by Boulder County. A qualified, Colorado -licensed engineer must perform the placement, drilling, and reinforcement of drilled piers. A signed, sealed and dated inspection report must be provided to Building Inspection Services prior to the rough inspections R110.5.2.3) % A perimeter drain system that discharges to an approved drainage system is required around all foundations that enclose usable spaces below grade. Foundations that retain earth and enclose interior spaces below grade must be damp proofed. (IRC R405.1, R406.1, BC Amendment R401.2.14) B Slabs below grade must maintain a minimum of 6 -inches above the design water table. The interior finished crawl space grade must be a minimum of 36 -inches above the design water table. (BC Amendment R401.2.1.3and 8401.2.1.5) S Garage floor surfaces must be approved noncombustible materials. Floors must be sloped to facilitate the movement of liquids to a drain or toward the main vehicle entry doorway. (IRC R309.1) 10 Foundation plates and sills must be bolted to the foundation wall as prescribed on the engineered plans. if not noted, bolts shall have a minimum diameter of %-inch, embedded at least 7 -inches and spaced not more than 6 -feet apart. A minimum of 2 bolts are required per plate section, with one bolt located within 12 -inches of each end of each plate. (IRC R403.1.6) w����a ,fit _�wheaQrQetg�r.6��. u Rough Framing and Wood Requirements 3 The complete rough inspection is to be made after the rough framing, rough electric, rough plumbing, and rough heat and ventilation are complete. The building should be fully enclosed with the roof covering and siding in place. 12 Protection from decay shall be provided in the following locations by the use of naturally durable wood or wood that is preservative treated in accordance with AWPA U1: (IRC R317) 13 Lumber, plywood, fiberboard, structural logs, and glued laminated timber must be identified by a grade mark or certificate of inspection issued by an approved agency. (IRC R502.1, R602.1, and R802.1) A. Wood joists closer than 18 -inches and wood girders closer than 12 -inches to grade located within foundation periphery.B. Wood framing members that rest on concrete or masonry foundation wails and are less than 8 -inches from the exposed ground. C. Sills and sleepers on a concrete or masonry slab that is in direct contact with the ground. D. Wood girders entering concrete or masonry walls with a clearance less than %-inch. E. Wood siding, sheathing, and wall framing less than 6 -inches above the ground. F. Wood members supporting moisture -permeable floors or roofs that are exposed to the weather. G. Wood furring strips or wood members attached directly to the interior of below grade exterior masonry or concrete walls. H. Wood in contact with the ground, embedded in concrete in direct contact with the ground or embedded in concrete exposed to the weather that supports permanent structures intended for human occupancy shall be approved pressure - preservative -treated wood. 13 Accessible under -floor areas shall be provided with a minimum 18 -inches x 24 -inches opening through the floor or 16 - inches x 24 -inches opening through the perimeter wall. When the access is through a below -grade wall an areaway of not less than 16 -inches x 24 -inches must be provided. Where equipment is located beneath the floor, the access opening must be within 20 -feet of the equipment and allow the removal of the largest piece of equipment. (IRC 8408.4 and M1305.1.4) 4 Basements greater than 200 square feet and every sleeping room shall have at least one operable emergency and rescue opening or a door to the exterior. 15 Emergency escape and rescue openings shall meet the following requirements: A minimum clear width of 20 -inches, a minimum clear height of 24 -inches, with a total net clear opening of 5 square feet for grade level windows and 5.7 square feet for all others. A sill height of not more than 44 inches measured from the finished floor to the bottom of the clear opening. Window wells for emergency escape and rescue shall provide a minimum net area of 9 square feet with minimum horizontal projection and width of 36 -inches. The area of the widow well shall allow the emergency escape and rescue opening to fully open. (IRC 8310) I ( Columns must be restrained to prevent lateral displacement at the bottom end to insure against uplift. (IRC 8301.2.1, R407.3) `r_ a Fire blocking shall be installed to cut off all concealed draft openings in the following locations: (IRC 302.11) A. In concealed spaces of stud walls and partitions, including furred spaces, vertically at the ceiling and floor levels, and at 10 - feet horizontal intervals.(;. At interconnections between concealed vertical and horizontal spaces such as occur at soffits, drop ceilings, and cove ceilings. U. In openings around vents, pipes, ducts, cable, wires, chimneys, fireplaces, and similar openings that afford apassage for fire at ceiling and floor levels. k?. In concealed spaces between stair stringers at the top and bottom of the run, and between studs in line with the run of the stairs at unfinished walls. f 8 At least one egress door shall be provided for each dwelling unit. The egress door shall be side -hinged, and shall provide a minimum clear width of 32 -inches (813 -mm) when measured between the face of the door and the stop, with the door open 90 degrees (1.57 rad). The minimum clear height of the door opening shall not be less than 78 -inches (1981 -mm) in height measured from the top of the threshold to the bottom of the stop. Other doors shall not be required to comply with these minimum dimensions. Egress doors shall be readily openable from inside the dwelling without the use of a key or special knowledge or effort. (IRC R311, R311.2) 19 There shall be a floor or landing on each side of each exterior door, except where a stairway with 2 or fewer risers located on the exterior side of the door, other than the required exit door, a landing is not required for the exterior side of the door. The landing must be no lower than 73/ -inches below the top of the threshold of the door provided the door does not swing over the landing. (IRC R311) ;W Stairways must be at least 36 -inches in width. Handrails shall not project more than 4% -inches. The maximum rise may not exceed 7% -inches. The minimum tread depth may not be less than 10 -inches. Minimum headroom is 6 -feet, 8 - inches. For stairways with solid risers a nosing of %-inch to 1X -inches shall be provided. When open risers are used the opening between the treads shall not allow the passage of a 4 -inch sphere. landings must be provided at the top and bottom of the stairway that is the width of the stairway measuring at least 36 -inches in the direction of travel. Handrails shall be provided on at least one side of stairways with 4 or more risers and ramps with a slope exceeding 1:12. Handrails shall be mounted 34 -inches to 38 -inches above the nosing of the treads. Handrails must be continuous for the entire length of the stairs and provided with a minimum space of 1'/a -inch between the wall and the handrail. Ends shall be returned or terminate in newel posts or safety terminals. See the requirements and more information. (IRC R311.7.8) 21 Handrail Grip Size Shall Be:A. Circular Handrails: 1% -inch to 2 -inches perimeter. B. Non -Circular: 4 -inches to 6% -inches perimeter with a maximum cross section of 2% -inches. C Perimeter Dimension Greater than 6% -inches: shall have a finger recess on both sides. 2.2 Guards must be provided for porches, screened porches, balconies, fixed seating and raised floor surfaces more than 30 -inches above the floor or grade below. Guards must have a minimum height of 36 -inches. Open sides of stairs with a total rise of more than 30 -inches above the floor or grade below shall have guards not less than 34 -inches high. Intermediate rails shall not allow the passage of a 4 -inch sphere. (R312) Window fall protection must be provided for window openings less than 24 inches above the finished floor and more than 72 inches above grade or surface below. (R312.2) 23 Ceiling heights for habitable rooms, hallways, bathrooms, toilet rooms, laundry rooms, and basements shall be a minimum of 7 -feet measured from the finished floor to the lowest projection of the ceiling. Non -habitable basements may have a ceiling height of 6 -feet, 8 -inches with clearance below beams and ducts of 6 -feet, 4 -inches. Bathroom may have a ceiling height of 6 -feet, 8 -inches at the fixture front clearance area and over the fixture. (IRC R305.1) �4- Attic access must be provided for attics that exceed 30 square feet and that have a vertical height of 30 -inches or greater. The access must be located in a hall or readily accessible location with a minimum 22 -inches x 30 -inches access opening. The access must provide a minimum of 30 -inches headroom. (IRC R807) 4 Form: B/24 ® Rev. � ,� Enclosed attic and rafter spaces must have cross ventilation for each space through screened openings. The total net free ventilating area shall not be less than 1 to 150 of the area of the space ventilated. The area may be reduced to 1 to 300 if 50-80% is provided by ventilators located in the upper portion of the space or if a vapor barrier not exceeding 1 perm is installed on the warm side of the ceiling. At least a 1 -inch space is required between the roof sheathing and the insulation at the location of the vent. (IRC R806) �6 Rafters must be framed to a minimum 1 -inch nominal ridge board that is not less than the depth of the cut end of the rafter or to each other using a gusset plate. Hip, and valley rafters shall be a minimum of 2 -inches and not less in depth than the cut end of the rafter. Hip and valley rafter shall be supported at the ridge by a brace to a bearing partition or be designed. (IRC R802.3) ? Rafters and ceiling joists having a depth -to -thickness ratio exceeding 5:1 shall be provided with lateral support at points of bearing to prevent rotation. Rafters and ceiling joists having a depth -to -thickness ration exceeding 6:1 shall be supported laterally by solid blocking, diagonal bridging or a continuous 1 -inch by 3 -inch wood strip nailed across the rafters. (IRC R802.8) Roof trusses or rafters must be attached to supporting walls with approved hurricane clips. Trusses must be braced to prevent rotation and to provide lateral stability in accordance with the construction documents and the individual truss design drawings. (IRC R502.11.2, R802.11) 2E Trusses must be designed and fabricated in accordance with ANSI/TPI 1. A licensed professional shall prepare the truss design. Trusses must be legibly marked within 2 -feet of the center to identify the manufacturer, the design load, and the spacing. Truss engineering and layout must be provided at the site at the rough framing inspection. (IRC R502.11 and R802.10) S Roofing material installed in the mountain areas is limited to Class -"A" roof coverings. Wood roofs in the plain areas are limited to minimum Class "B" roof coverings. Shingle installation shall meet the manufacturer's high -wind installation procedures in areas where wind load is greater than 105 mph (V3S). Chapter 9, R301.2.1, R325, and manufacturer's listing 30. All habitable rooms shall be provided with aggregate glazing area for natural light of not less than 8% of the floor area of such rooms. The glazed areas need not be installed in rooms where section M1507 is satisfied and artificial light is provided at an average of 6 foot candles at a height of 30 inches. 31 Safety glazing shall be installed in the following hazardous locations and be permanently labeled as safety or tempered glazing: glazing panels in doors; glazing enclosing spas, bathtubs or showers; glazing panels adjacent and within 24 -inches of the edge of a door; glazing panels greater than 9 square feet within 18 -inches of the floor; glazing used for railings; glazing used for barriers for swimming pools and spas; and glazing enclosing stairways, landings, and ramps within 36 -inches horizontally of a walking surface. See the Boulder County Land (IRC R308) 32 Roofs decks and enclosed roofed areas must be provided with roof drains installed at the low point of each roof. Where roof drains are installed, overflow drains or scuppers are required. (IRC R903.4) 33 Exterior finish materials must conform to the conditions of your Site Plan Review to include: roof covering, siding, color requirements, conforming light fixtures which comply with the approved lighting plan. Glazing and Window Requirements 3� Skylights must be: (IRC 8308.6 Table N1102.1) A. laminated glass (with restrictions). B. fully tempered glass (with retaining screen). C. heat -strengthened glass (with retaining screen). D. wired glass (with retaining screen in multiple glazing condition only). E. approved rigid plastic. F. Skylight U -factor required U-0.45. Skylights installed on roofs flatter than 3 units vertical to 12 units horizontal must be mounted on a curb 4 -inches above the roof. Heating and Ventilation Requirements 33 Crawl spaces shall be provided with conditioned air in compliance with Section N1102.2.9. Crawl space walls shall be insulated in accordance with Table N1102.1 or Table N 1102.1.2. Crawl space wall insulation shall be permanently fastened to the wall and extend downward from the floor to the finish grade level and then vertically and/or horizontally for a least an additional 24 -inches. Exposed earth in unvented crawl space foundations shall be covered with a continuous Class I vapor retarder with a minimum thickness of 10 -mil. All joints of the vapor retarder shall overlap by 6 -inches and be sealed and taped. The edges of the vapor retarder shall extend at least 6 -inches up the stem wall and shall be attached to the stem wall. N1102.2.9.2.2 Ventilated crawlspaces. Ventilated crawispaces shall be provided with insulation in accordance with Table N1102.1. 34 A. Habitable rooms must be provided with outdoor openings for ventilation equal to at least 4% of the floor area and shall have heating facilities capable of maintaining 68` at 3 -feet above the floor and 2 -feet from exterior walls. B. The windows need not be openable in a room where an opening is not required to be an egress window and a mechanical ventilation system is capable of producing 0.35 air change per hour in that room, or a whole house mechanical ventilation system provides 15 cubic feet of outdoor air per minute. 35 Bathroom exhaust fans shall exhaust directly to the exterior and must be provided in bathrooms where windows of at least 3 square feet are not provided. The mechanical ventilation must be capable of providing an exhaust capacity of 50 cfm intermittent or 20 cfm continuous exhaust. (IRC R303.3, M1507.4) 36 Dryer vents must be rigid metallic, independent of all other systems, shall terminate outside the building, be equipped with a back draft damper, and sized and terminated per the manufacturer. The maximum length of the exhaust duct shall be 35 -feet (Unless approved under the manufacturer's listing) from the connection to the transition duct from the dryer to the outlet terminal. Where fittings are used, the maximum length of the exhaust duct shall be reduced in accordance with (IRC Table M1502.4.4.1) Flexible transition ducts are limited to 8 -feet, shall not be concealed within construction, and shall be listed and listed per UL 2158A. (IRC M1502) 37 Appliances and equipment shall be installed in accordance with the conditions of their listing. Manufacturer's installation instructions must be available at the time of the inspection. (IRC G2408.1, M1307.1, M1401.1,(M1902.2) 39 Appliances shall be accessible for inspection, service, repair and replacement without removing permanent construction. 30 -inches of working depth and width shall be provided in front of the control side of an appliance. (IRC M1305.1) 3� Gas and solid fuel appliances located in a garage and hazardous locations shall be elevated so the source of ignition is at least 18 -inches above the floor. Rooms and spaces that are communicate directly with the garage and are not part of the living space shall be considered as part of the garage. Appliances located in garages must be installed at least 6 -feet above the floor or protected from motor vehicle impact. (IRC G2408.2, G2408.3) 40 Combustion air is required for all liquid fuel, solid fuel and gas appliances. (IRC M1701.1, 62407) Gas burning appliances may not be located in or obtain combustion air from: a sleeping room, bathroom, toilet room, or storage closet unless it is a direct vent appliance or installed in an enclosure that opens only into a bedroom or bathroom in and such enclosure is provided with a solid weather-stripped door, a self-closing device and all combustion air is taken from the outdoors. (IRC G2406.2) �1 Gas logs installed in solid fuel burning fireplaces shall be tested in accordance with ANSI 221.60 and installed per the manufacturers installation instructions. Gas logs installed in bedrooms must be direct vent or provided with an approved source of outside combustion air. The approved gas log set must be installed in the Solid -fuel burning appliances at the final inspection. (IRC 62406, G2432, and G2434) 43 B, BW, and L vents and factory -built chimneys must be provided with a clearance to combustibles per them a manufacturer's listing. Where vents pass through insulated assemblies, they must be provided with an insulation shield. A clearance of 9 -inches is required between single wall vent connectors and combustibles. Gas vents must penetrate through the roof flashing, jack or thimble and terminate in a Chimneys listed cap or per the manufacturers listing. Decorative shrouds installed at terminations shall be listed and installed per the manufacturer. (IRC G2425, G2426, G2427) Electrical Requirements 44 All electrodes present at each structure shall be bonded together to form one grounding electrode system to include: Concrete Encased Electrodes (UFER), water piping, ground rings, grounding rods, and plate electrodes. Bonding shall ensure electrical continuity. The electrode conductor must be connected in an approved manner and inspected prior to concealing. (IRC E3607, E3608, E3609, E3610, E3611) 45 All hot, neutral, and grounding conductors in electrical boxes shall be tied together with a mechanical connection at the time of rough inspection. 46 Recessed lighting fixtures must either be IC -rated or installed in a sealed box in which the insulation is at least 3 -inches from the light fixture. All recessed lights must be tightly sealed or gasketed to prevent air leakage through the fixture into the ceiling cavity. (IRC N1102.4.5) 47 Tamper-resistant Receptacle outlets are required in every kitchen, family room, dining room, living room, parlor, library, den, sunroom, bedroom, recreation room or similar dwelling areas spaced so that no point along the wall line exceeds 6 -feet from an outlet. (IRC E3901, E3902, and 4002.1-4002.14)A Counters 12 -inches in width or wider shall have receptacles placed no more than 20 -inches above the counter top and spaced so no point exceeds 24 -inches from an outlet. B Island and peninsula counters with a length at least 24 -inches and a width of 12 -inches or greater must be equipped with at least one outlet. C. At least one receptacle shall be installed in a bathroom within 36 -inches of each basin. C. A least one receptacle outlet must be installed in each laundry, basement, attached garage and detached garage with power. F. At least one receptacle outlet that is accessible while standing at grade level and located not more than6- feet, 6 -inches (1981 -mm) above grade, shall be installed outdoors at the front and back of each dwelling unit having direct access to grade. Balconies, decks, and porches that are accessible from inside of the dwelling unit and that have a usable area of 20 square feet. F. Attics or crawlspaces containing equipment must be provided with at least one receptacle outlet within25-feet of the equipment. G. Hallways 10 -feet or more in length. OP'Two 20 -amp rated branch circuits shall serve receptacles in the kitchen, pantry, breakfast area, and dining area. At least one 20 -amp branch circuit shall supply bathroom receptacles and at least one 20 -amp branch circuit shall supply laundry. (IRC E3703.2, E3703.3, E3901) SO Ground fault protection shall be provided on all 125 -volt, single phase, 15 and 20 -amp receptacles in the following locations: bathrooms, garages, unfinished grade level accessory buildings, at exterior locations, crawlspaces, unfinished basements, kitchen counters, within 6ft. of laundry, utility and wet bar sinks, boathouses, hydro massage, spa and hot tub locations. Receptacles must be in a readily accessible location. (IRCE3902, E3902.11) 51 Combination type arc -fault circuit interrupters must be installed on all 120 -volt 15 and 20 -amp branch circuit outlets in Receptacle outlets are required in every family room, dining room, living room, parlor, library, den, sunroom, bedroom, recreation room, hallway, closets, and similar dwelling areas. (IRC 3902.12) 52 At least one wall switch -controlled lighting outlet shall be installed in every habitable room, bathroom, hallway, (10ft) stairway, attached garage, detached garage with electric power, and at the exterior side of each outdoor egress door having grade level access. Attics, under floor spaces, utility rooms and basements containing equipment or used for storage must be provided with a switch 53 Smoke alarms shall comply with UL 217. Smoke alarms are to be powered by the building's wiring operated light. (IRC E3903)with battery backup and shall be interconnected so the actuation of one alarm will activate all alarms in the dwelling unit. Smoke alarms shall be installed in the following locations: (IRC R314) A. In each sleeping room; 8 Outside each sleeping area in the immediate vicinity of the bedrooms; and C One on each additional story including basements. 54 Carbon Monoxide alarms are required in a single-family dwelling that has fuel -fired appliance(s), or a fireplace, or an attached garage. The alarm must be installed within 15 -feet of the entrance to each sleeping room. Must be listed by a nationally recognized, independent lab. Plugs into a dwelling's electrical outlet and has a battery backup. They may be combined with a smoke -detecting device if the combined device complies with applicable law. (IRC R315) 55 Clothes closet lighting shall be limited to surface -mounted or recessed incandescent fixtures with completely enclosed lamps, and surface -mounted or recessed fluorescent fixtures.Surface mounted fixtures shall be installed on the wall above the door or on the ceiling with the following clearances between the fixture and the nearest point of a storage space: (IRC E4003.12)A. Incandescent fixtures or LED shall have a minimum 12 -inch clearance. B. Fluorescent fixtures shall have minimum 6 -inch clearance. Recessed fixtures shall be installed in the wall or ceiling with the following clearances: A Recessed incandescent fixtures shall have a minimum 6 -inch clearance to the nearest point of storage. B. Recessed fluorescent fixtures shall have a minimum 6 -inch clearance to the nearest point of storage. 56. Working space must be provided around energized equipment for servicing and maintenance. The minimum dimensions shall not be less than 36 -inches in depth and 30 -inches in width in front of the equipment. Working space shall extend to at least 6 -feet, 6 -inches above the floor. (IRC E3405.2) 57 Electrical fixtures installed in wet or damp locations shall be installed so that water cannot enter or accumulate n wiring compartments or other electrical parts. Fixtures installed in wet locations must be labeled "suitable for wet locations". Fixtures installed in damp locations must be labeled "suitable for damp locations" or "suitable for wet locations". Switches or circuit breakers located in wet locations or outdoors must be enclosed in a weatherproof enclosure. Outdoor receptacles must have a weatherproof enclosure and an in -use cover. Cord -connected fixtures, hanging fixtures, track lighting, pendants, and ceiling fans shall not be located within3-feet horizontally and 8 -feet vertically from the top of a tub or shower rim. (IRC E4003.9, E4002.8, E4002.9,E4002.10, E4003.9, E4003.10,E4003.11) Plumbing Requirements E, URN systems sh2H be tested on compellation of the rough piping installation by water or for piping system other than plastic by air with no evidence of leakage. Either test shall be applied to the drainage system in its entirety or in sections after rough piping has been installed . ► ) Water test 10 fejt above the highest fitting connection or to the highest point of the completed system. The system shall prove leak free for 15 minutes. �) Air test shall maintain 5I hs of pressure for 15 minutes. �9 Piping must be inspected and tested prior to concealing. It shall be protected against physical damage and it must be approved for use and bear the identification of the manufacturer. (IRC P2503, P2603, P2608.1) 60 Bathtubs, walls above bathtubs with shower heads, shower floors, and shower compartments shall be finished with a non-absorbent surface which extends to a height not less than 6' above the floor. Showers must have a minimum 900 square inches of interior area and a minimum dimension in each direction of 30 -inches. Shower valves must be pressure balance/thermostatic mixing valves. Shower receptors shall have a curb threshold not less than 1 -inch below the sides and back of the receptor. The curb shall measure a minimum of 2 -inches to a maximum of 9 -inches above the top of the drain. (IRC R307, P2708, P2709) 61 The centerline of toilets or bidets shall not be less than 15 -inches from adjacent walls or tub. Toilets, bidets, and lavatories must have a minimum clear space of 21 -inches in front of the fixture. lavatories require a 4 -inch clearance to wall or to a toilet. (IRC P2705) 62 Showers and tub/shower combinations shall have control valves of the pressure balance, thermostatic mixing or combination pressure balance/thermostatic mixing valve types with high limit stop per ASSE 1016 or CSAB125.1. Tubs shall also have a control valve as listed for a shower or a water -temperature -limiting device that conforms to ASSE 1070. The high limit stop for a device shall be set to a maximum of 120'. (IRC P2708.3,P2713.3) 63 Shower doors shall have safety glazing; hinged show door shall open outward. (8308.4.5 , P2708.1) 64 Backflow prevention must be provided to prevent contamination of potable water. This includes but is not limited to: hose connections, irrigation systems, boilers, solar systems, fire sprinklers, and dishwashers. (IRCP2902.2, Table P2902.3, P2717) Insulation 6S R-20 Walls R49 Ceiling R-19 Crawlspace Window U -Factor .32 Floor R-30 66 Supply Ducts in attics shall be insulated to a minimum of R -g. All other ducts shall be insulated to minimum R-6. ( N 1103.2.1) 6? Combustible insulation shall be separated a minimum of 3 -inches from fan motors and heat -producing devices. Insulation shields must be provided where vents pass thorough insulated assemblies and must terminate at least 2 -inches above attic insulation materials. Can lights must be airtight if located in the building envelope. (G2426.4) Class I or If vapor retarders are required on the interior side of the insulation in framed walls, floors and roof/ceilings of the building's thermal envelope. The vapor barrier is not required in construction where moisture or freezing will not damage the materials, or where the framed cavity (or space) is ventilated to allow moisture to escape. A vapor retarder is not recommended on a concrete basement foundation wall or in a shower /bath compartment (IRC 702.7, R702.7.1). Wallboard Requirements E>P The garage shall be separated from the residence and its attic by materials of not less than %-inch gypsum board applied to the garage side. Garages beneath habitable rooms shall be separated from all habitable rooms above by not less than 5 8-inch Type X gypsum board. Where the separation is a floor-ceiling assembly, the structure supporting the separation shall also be protected by not less than %:-inch gypsum board. (IRC 8302.6) Openings between the garage and residence shall be equipped with solid wood doors not less than 1-inch in thickness, solid or honeycomb core steel doors not less than 1-inch thick, or 20-minute fire-rated doors. Openings are prohibited between garages and rooms used for sleeping. (R302.5.1 )Doors between attached garages and living space shall be weather stripped to the degree necessary to make them airtight and shall be self-closing and self-latching. 69 Enclosed accessible space under stairs shall have walls, under stair surface and any soffits protected on the enclosed side with %:-inch gypsum board (IRC R302.7). 70 Cement, fiber -cement, glass mat gypsum backer and fiber reinforced gypsum in compliance with ASTM C 1288, C 1325, C1178, or C1178 and installed in accordance with manufacturer recommendations shall be used as backers for wall the in tub and shower areas and wall panels in shower areas. (IRC R702.4.2) 71 Mail spacing for gypsum board % gypum board Ceiling 16oc, 7", nails 12", Type S screws % wall spacing 24"OC, 8" nailspacing. 12"OCscrews. 5/8 ceiling board 16"OC, 7"nails I 2"spacing, screws 240C 8". 72 Water-resistant gypsum backing board used as the base or backer for adhesive application of ceramic tile or other required nonabsorbent finish material shall conform to ASTM C1396, C1178 or C1278. It is permitted on ceilings where framing spacing does not exceed 12 -inches o.c. for %-inch thick or 16 -inches o.c. for 5 8 -inch thick gypsum board. Water- resistant gypsum board shall not be installed over a vapor retarder in a shower or tub compartment and may not be used where there will be direct exposure to water, or in areas of continuous high humidity. All cut and exposed edges shall be sealed. (IRC R702.3.8) 73 Floor assemblies, not required elsewhere in this code to be fire resistance rated, shall be provided with a % inch gypsum wall board membrane, 5/8 inch wood structural panel membrane, or equivalent on the underside of the floor framing member.(IRC 501.3) Final Inspection Requirements 74 Buildings shall have approved address numbers, building numbers or approved building identification placed in a position that is plainly legible and visible from the street or road fronting the property. (IRC 319) 75 All dwellings shall have a controlled method of water dispersal from roofs that will collect and discharge all roof drainage at least 5 -feet from the foundation. Gutters, downspouts, downspout extensions shall be deemed adequate to meet these requirements. Surface drainage shall be diverted to a storm sewer conveyance or other approved point of collection so as to not create a hazard. Lots shall be graded so as to drain surface water away from foundation walls. The grade away from foundation walls shall fall a minimum of 6 -inches within the first 10 -feet. (IRC R401.3 and R801.3) Swimming pools, fountains, hot tubs, spas, and hydro -massage "Jacuzzi" tubs and similar installations shall comply with all provisions of the IRC for the approval of bonding equipment and lighting. All 15 and 20 amp, single-phase 125 -volt receptacles located within 20 -feet of the inside walls of pools, outdoor spas and hot tubs shall be protected by a GFCI. Motors and equipment must be accessible without damaging the building structure or building finish. (IRC E4202,E4203, EE4204, E4205, E4206) The reinforcing shell of the pool shell, metal forming shells, coping stones, deck, brackets of niche fixtures, metal fittings, and electrical equipment, located less than 5 -feet horizontally and less than 12 -feet above maximum water level of swimming pools and built in place hot tubs shall be bonded together. The parts specified above shall be connected to an equipotential bonding grid. (IRC E4204.2) City of Wheat dge COMMUNITY DEVELOPMENT Reviewed for Code Com liance Total of Remodel area: less than 482 SF Existing Kitchen, Powder Room, and Laundry 9 11Citchen Upgrades for Mark and Kim Adamson 11596 W 38th Place Wheat Ridge, 80033 7-17-2017 No Scale Wirth - ,:, heat R'd9e Proposed Kitchen, Powder Room, and Laundry Kitchen Upgrades for Mark and Kim Adamson 11596 W 381h Place Wheat Ridge, 80033 7-17-2017 No Scale North gat 41,a9e � �t3lD10) ' E ki R 'III gmvij�ii h Proposed Kitchen Upgrades for Mark and Kim Adamson 11596 W 38" Place Wheat Ridge, 80033 7-17-2017 No Scale r C�tyof Proposed Kitchen Upgrades for Mark and Kim Adamson 11596 W 38"' Place Wheat Ridge, 80033 7-17-2017 No Scale L L L "Ot �U;, h��tR'°9� `7' - 1Daa*te; City of ��'Wh6at�p *d `ommuwn DEVEI 0 C PMENT PlanMermit # BuYding & Inspection Services Division 12 -c -a 7500 W, 29h Ave., Wheat Ridge, CO 80033 Plan Review Fee: Office: 303-235-2855 * Fax: 303-237-8929 Inspection Line: 303-234-5933 BuildngPermit Application PAID --- -- ---- - - - - Address: City, State, Zip: Electdcal: W,R. City License# Plumbing, W.R,'City License # Mechanical: W.R. City License # Complete all information on BOTH sides of this form M MGE��� Sq. FtJLF Btu's Gallons Amps Squares Other �aL-17- OWNERICONTRACTOR SIGNATURE OF UNDERSTANDING AND AGREEMENT I hereby certify that the setback distances proposed by this permit application are accurate and do not violate applicable ordinances, rules or regulations of the City of Wheat, Ridge or covenants, casements or restrictions of record; that all measurements shown and allegations made are accurate; that I have read and agree to abide by all conditions printed on this application and that I assume full responsibility for compliance with applicable City of Wheat Ridge codes and ordinances for work under any permit issued based on this application; that I ant the legal owner or have been authorized by the legal owner of the property to perforur the described work and am also authorized by the legal owner of any entity included on this application to list that entity on this application. 4100tDW (OWNER)C(CONTJ?AciD12) (AUTHORIZED REPRESENTATIVE) of (OWNER) (CONTRACTOR) x Building Division 4alustion: Mark Adamson Via E -Mail: berfeemoose@comcast.net On May 4, 2015, 1 inspected the above referenced property at your request. The purpose of the inspec- tion was to visually observe the foundation of the home to determine my professional opinion of the structural condition thereof, in order to determine whether structural repairs are needed at this time, and to recommend a plan of repair as needed, The inspection did not involve any other system or component of the residence. No soil or other material sampling, testing, or analysis was performed by Coyle Struc- tural Inspection, Engineers. General Information: • The home is a I story single family home structure, assumed to be facing East. The home was re- portedly constructed in 1967. • The foundation is of poured concrete construction. • Theperim eter walls of the upper structure are of conventional wood frame construction, • No soils report or other architectural/engineering documents were available for review. Observations, Opinions and Recommendations: • The home is reasonably level and without indication of significant vertical movement. • However, the rear foundation wall of the basement has experienced excessive inward displacement and cracking. The displacement and cracking are structurally significant, and, restraint is recom- mended. • It is recommended to install seven wall anchors at the rear foundation wall per the attached diagram. Foundation excavation and wall realignment are not structurally imperative, though optional. • The garage floor slab has experienced major settlement, due to consolidation of the backfill soil, Although not structurally imperative, removal and replacement of the garage floor slab should be con- sidered, along with addition of compacted soil. Additional Comments: • All foundations are subject to movement over time, due to variations in soil and moisture conditions. The home should be monitored for additional future movement, and Any significant movement should be reported to this office for further evaluation and recommendation. • For any and all recommended work, care needs to be taken in the areas of underground and overhead utilities. All work to be done in compliance with local and national safety standards, and building de- partment regulations. • This inspection and report do not constitute an evaluation of potential asbestos containing materials or lead based paint, as may be required prior to any demolition, remodeling, or repair. zm� Limitations and Understanding: • This inspection was visual in nature (no invasive procedures or material sampling/testing), but repre- sents the opinions of this firm for the area in question,, based on visible components, observations made, and any information provided. • Our opinions may change if there is a change of conditions, accessibility, or visibility from the time of the initial inspection, or if additional information becomes available for consideration. • No warranties are made or implied as to the continued structural integrity of this property, as geology, soil, and moisture conditions are unpredictable, and unknown geological/soil/structural conditions could exist. • Therefore, the value of the inspection and opinions expressed, is mutually agreed to be limited to the amount of the fee charged for the service. Thank you for allowing me to be of service. Please feel free to call if you have any questions, Very truly yours, Coyle Structural Inspection Engineers, Inc. Michael D. Coyle, PX. President wm� COYLE STRUCTURAL INC. s 12* Interior wall plate, 3 " X 28" � a� min 4- galvanfZed rod; a85 i mn tensile" 4' ofstrength.per engineer € Eat nch r'Plates _ " X 26,E WALL ANCHORS -ndbon,tts r , + ri -Tite, or Engineers Approved Equal, Any ather Memative products must be approwdby the Engineer prior to submission for buildingp at �Q, CITY OF WHEAT RIDGE CODE DESIGN CRITERIA: • 20121 • Roof Snow Load 30 psf • is Wind Speed 105 mph (3 -second gust) • Wind Exposure C • Seismic Design Category Residential B WALL ANCHORS (Approved Systems): • Geo -Lock Wall Anchors, by Foundation Supportworks. • Grip-Tite Wall Anchors, by Grip-Tite Foundation Systems. • Alternates other than the above to be submitted to the engineer for review and approval. Must have minimum 3/4" all thread rod with minimum capacity of 8,000 lbs, and all partsgalvan- ized to ASTM 153 or approved equal. EPDXY INJECTION: • All cracks of 1/16" or larger shal be epoxy injected. • Sikadur* 35 Hi -Mod LV or approved equal. 11pipip piip;111� NUM tE STRUCTURAL INSPECTION ENGINEERS, INC. in order to promote long term structural integrity for the property. wm� m F F if sto 11420 ir F F if wl to CL Tj 17 1 8 - "JI (ro IQ tit of, �, w g COMMUN11Y DEVELOPMENT Building & Inspection Services Division 75 W. 29" Ave., Wheat midge, CO 80033 Office: 303-235-2355 Fax: 303-237-8929 Inspection Request Line.* 3t 3-23 -5933 Building r t Application (Complete Aff highlighted areas) Property Address. Mailing Address: (if different than property address) address: City, State, Zip; Contractor Plan 1# _ Permit IRRI N License �Phon�e.36�- Plu mbin : Mechanical: City License #t City License ## City License ## L ` r r :` (Pally describe wart to be performed - Attach additional street if necessary) Contract Value of all r r hu U Review Fee (due at time of submittal): Squares ,_ U's tial€arts � �Amps Std Ft. OWNER/CON'tRACTOR SIGNATURE fF UNDERSTANDING AND AGREEMENT 1 lre°relay certify that the setback disi anee, proposed by this lacrtttit arlsltliccation ars: accurateand do not violate applicable ble olitirr rrr e , titles or regulations oftlae City of Wheal Ridge e, or coveleltat,�, Amseraaents (mak restrictions of record, drat a ll aaaearsur•emerats shown and allegations made are, accurate, that t have read and agrev to abide 4 all conditions printed oil this application and tlraat 1 atsaatatrre° f"oll rc'altonsrtaility$ for compliance suit!) applicable City of Whent lithe coders and ordinances llsr work under array+ lsennit r" a;arrcd lsarsed oil this application, (111111 array the leltal owner or have he ll authorized Ery tile: legal oavttc r of the property to perfotan the described wear roti am trlsta atrtlrorizetl by the legal owner ol`any entit}r included t>ra this application to list that entity ora this a) ion, C"IACCC:iC`OAT',• (031WER) (CONTRACTOR) { tai�Tfift/ I^i) L fit a5` ,4`7.a#7"tt a) of (ri€►'AILR) 4TRACTOR) a i to : IGNA UR ' DATE:� � CZ �. Bldg Valuation: $_ Eli 91 9 =��Prffa a im 10 0 W 1-1 - - ------ TEAR OUT SPEMAG1� JNa�'�".�71�iCTJOMS. EXISTS INSIDE 0 Measured Outside 0 Out Back Drywall ST �E OF HOUSE 0 Gut 5a0k Sill fiWeaWredinside EXISTS OUTSIDE QFlashing Needed MlAngle, Needed ._I ADDER )SlOII Needed )Wroove Filler Casing c a ♦ i CITY OF WHEAT RIDGE Building Inspection Division (303) 234 -5933 Inspection line (303) 235 -2855 Office (303) 237 -8929 Fax INSPECTION NOTICE Inspection Type: I7Ox4 Job Address: 1149Z, /1/ 5' i 3,g � fl- -Z e- Permit Number: ❑ No one available for inspection: Time 1.2,� AM`PN: " Re- Inspection required: Yes N o , r * When corrections have been made, tali for re- inspection at 303 -234 -5933 Date: 12 - Jg - © 1 7 Inspector: ' DO NOT REMOVE THIS NOTICE 4 r INSPECTION RECORD -- OCCupanGyrryDe INSPECTION LINE (303) 234 - 5933 Inspections will not be made unless this card is posted on the building site Call by 3:00 PM to receive inspection the following business day. INSPECTOR MUST SIGN ALL SPACES, PERTAINING TO THIS JOB x FOUNDATION INSPECTIONS DATE INSPECTOR INITIALS COMMENTS: Footings /Caissons Sheathing %emwall / (CEG) Concrete Encased Ground f Reinforcing or Monolithic Roof Weatherproof / French Drain Mid Roof :Electrical Service Sewer Service Lines`: A) c¢ Water Seance Lines «7�e. - t71?n ?7 G' .: +✓ ' ✓i �. <'POUR No CONCRETE UNTIL ABOVE HAS BEEN SIGNED CONCRETE SLAB FLOOR C Electrical (Underground) u Plumbing (Underground) Heating (Underground) DO NOT POUR FLOOR UNTIL ABOVE. HAS BEEN SIGNED 5` ( F f >s- f .ROUGHS Electrical Sheathing Mechanical Lath /'Wall tie Roof Mid Roof :Electrical Service a k5li,lI % r� �✓9✓!' G,zicl / �> I I I 1.r5✓,cJ� A) c¢ Rough Electric «7�e. - t71?n ?7 G' .: +✓ ' ✓i �. z..;s `J r .Rough Plumbing !( ..Gas Piping Rough Mechanical Framing FINALS Electrical Plumbing Mechanical Roof Building Final ,Fire Department ;. R:O W &Drainage INSPECTIONS FOR PLANNING $ ZONING, FIRE ANDSPUBLICE WORKS ULD BE CALLED AT LEAST ONE WEEK PRIOR TO FINAL INSPECTIONS. Parking & Landscaping -. "NOTE. ALL ITEMS MUST BE COMPLETED AND APPROVED BY PLANNING AND ZONING, :BUILDING: AND PUBLIC WORKS. BEFORE A CERTIFICATE OF OCCUPANCY 1S ISSUED. FINAL INSPECTION BY THE BUILDING DIVISION DOES NOT CONSTITUTE AUTHORIZATION OF ACERTIFICATE OF OCCUPANCY NOR PERMISSION FOR OCCUPANCY. VCCUPANCY NOT PERMITTED UNTIL CERTIFICATE OF OCCUPANCY IS ISSUED PROTECT THIS CARD FROM THE WEATHER ♦ i CITY OF WHEAT RIDGE Bung Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: 121,1 /(./woe Job Address: 1/S96 ~csi 38/sce Permit Number: ❑ No one available for inspection: Time AM/PM Re-Inspection required: Yes No *When corrections have been made, call for re-inspection at 303-234-5933 Date: /Z /o,%o9 Inspector: EV DO NOT REMOVE THIS NOTICE ~oF W"E'?qo City of Wheat Ridge Building Division m 7500 W. 291h Ave., Wheat Ridge, CO 80033 Office: 303-235-2855 * Fax: 303-237-8929 °o<oaro° Inspection Line: 303-234-5933 Date: Plan Permit #:0 Building Permit Application Property Address: /I~G Property Owner (please print): Phone 3 `fe2 ? o2`f Mailing Address: (if different than property address) Address City, State, Zip Contractor: &o I Contractor license ;L - 23G y Phone: z) ? Sub Contractors: Electrical City License Plumbing City License Mechanical City License Company: Company Company: Exp. Date: Exp. Date: Exp. Date Use of space (description): /(g5l- rLuc Description of work: G' )4 Sq. Ft./L. Ft added: Squares -?u _ BTU's Construction Value: $ 2<= (as calculated per the Building Valuation Data sheet) Plan Review (due at time of submittal): $ Gallons Amps OWNERICONTRACTOR SIGNATURE OF UNDERSTANDING AND AGREEMENT 1 hereby certify that the setback distances proposed by this permit application are accurate, and do not violate applicable ordinances, rules or regulations of the City of Wheat Ridge or covenants, easements or restrictions of record; that all measurements shown, and allegations made are accurate; that I have read and agree to abide by all conditions printed on this application and that I assume full responsibility for compliance with the Wheat Ridge Building Code (I.B.C) and all other applicable Wheat Ridge Ordinances, for work under this permit. Plans subject to field inspection. CIRLCE ONE.: (OWNER) PRINT NAME: PERSONAL REPRESENTATIVE of (OWNER) (CONTRATOR) rr- SIGNATURES ~9.~- Date: lliU'C;F `Fcedv 6 Bldg Valuation: $ 1 i INSPECTION NOTICE Inspection Type: Job Address: Permit Number: 1-9 i f. ❑ No one available for inspecti ime AM/PM , Re-inspection required: Yes Nol p•- tion at 303-234-5933 'When corrections have been made, calf VHNOTICE r Date: Inspector: DO NOT REMOVE i PROTECT THIS CARD FROM TH F--: p~ WHEgTq/ City of Wheat Ridge Building Division ° 7500 W. 29th Ave., Wheat Ridge, CO 80033 Office: 303-235-2855 ` Fax: 303-235-2857 p --=~o Inspection Line: 303-234-5933 OCORPp p Building Permit Application Date: ( /(c Plan Permit Property Address: It S,=)&o 'c Property Owner (please print): t~e+L yy}~ ~ Phone:'- O'0 3 - Mailing Address: (if different than property address) Address: City, State, Contractor: Contractor License [3€`Xc>&So Phone: Sub Contractors: Electrical City License Plumbing City License Mechanical City License Company: Company Company: Exp. Date: Exp. Date: Exp. Date: Approval: Approval: Approval: Use of space (description): Construction Value: $ -7Gr;.e& Description of work: (as calculated per the Building Valuation Data sheet) ~j'L-(1V~Yry"g(y~ t Wt'•.~ , Plan Review (due at time of submittal): $ y Sq. Ft./L.Ft added: Squares BTU's Gallons Amps OWNER/CONTRACTOR SIGNATURE OF UNDERSTANDING AND AGREEMENT I hereby certify that the setback distances proposed by this permit application are accurate, and do not violate applicable ordinances, rules or regulations of the City of Wheat Ridge or,covenants, easements or restrictions of record; that all measurements shown, and allegations made are accurate; that I have read and agree to abide by all conditions printed on this application and that I assume full responsibility for compliance with the Wheat Ridge Building Code (I.B.C) and all other applicable Wheat Ridge Ordinances, for work under this permit. Plans subject to field inspection. CIRLCEONE:: (OWNER) coNTRACTOR).dr PERSONAL REPRESENTATIVE of (OWNER) OTLj PRINT NAME: ~GNATURE: Date:7'~7'9 DEPARTMENT USE ONLY ZONING COMMENTS: Zoning: Reviewer: PUBLIC WORKS COMMENTS: Reviewer. BUILDING DEPARTMENT COMMENTS: OCCUPANCY Reviewer: FIRE DEPARTMENT:: ❑ approved w/ comments ❑ disapproved ❑ no review required Bldg Valuation: $