Loading...
HomeMy WebLinkAbout3625 Chase Streetc City of Wheat Ridge Resid. Windows/Doors PERMIT - 201708084 PERMIT NO: 201708084 ISSUED: 10/09/2017 JOB ADDRESS: 3625 Chase ST EXPIRES: 10/09/2018 JOB DESCRIPTION: Permit to replace 7 windows like for like with retrofit vinyl windows, with U value .28 or better according to manufacturers specs. *** CONTACTS *** OWNER (720)495-3535 MAGALEI STEFANIE NICOLE SUB (770)433-8211 Gary Cummings 170102 Home Depot U.S.A., Inc. *** PARCEL INFO *** ZONE CODE: UA / Unassigned USE: UA / Unassigned SUBDIVISION CODE: 2412 / LAKESIDE, STEWART GARDENS, OLI BLOCK/LOT#: 0 / *** FEE SUMMARY *** ESTIMATED PROJECT VALUATION: 5,241.00 FEES Window Replacement 50.00 Total Valuation 0.00 Use Tax 110.06 ** TOTAL ** 160.06 *** COMMENTS *** *** CONDITIONS *** Windows shall comply with all applicable codes, have a .32 or better U -factor and shall be safety glazing if within a tub enclosure, less than 18 inches above the floor or within 24 inches of a vertical edge of a door. I, by my signature, do hereby attest that the work to be performed shall comply with all accompanying approved plans and specifications, applicable building codes, and all applicable municipal codes, policies and procedures, and that I am the legal owner or have been authorized by the legal owner of the property and am authorized to obtain this permit and perform the work described and approved in conjunction with this permit. I further attest that I am le ally authorized to include all entities named within this document as parties to the work to be performed and that all work to be pe� ed is disclosed in this document and/or its' accompanying approved plans and specifications. Signature of OWNER or ,dNTRACTOR (Circle one) Date 1. This permit was issued based on the information provided in the permit application and accompanying plans and specifications and is subject to the compliance with those documents, and all applicable statutes, ordinances, regulations, policies and procedures. 2. This permit shall expire 365 days after the date of issuance regardless of activity. Requests for extension must be made in writing and received prior to the date of expiration. An extension of no more than 180 days made be granted at the discretion of the Chief Building Official and may be subject to a fee equal to one-half of the originalppermit fee. 1 If this permit expires, a new permit may be required to be obtained. Issuance of a new permit shall be subject to the standard requirements, fees androcedures for approval of any new permit. Re -issuance or extension of expired permits is at the sole discretion of the Chief Building Official and is not guaranteed. 4, No work of an manner shall be performed that shall results in a change of the natural flow of water without prior and specific approval. 5. The permit holder shall notify the Building and Inspection Services Division in accordance with established policy of all required inspections and shall not proceed or conceal work without written approval of such work from the Building and Inspection Services Division. 6. The issuance or granting of a permit shall not be construed to be a permit for, or an approval of, any violation of any provision of any applicable code or any ordinance or regulation of this jurisdiction. Approval of work is subject to field inspection. Signature of Chief Building Official Date REQUESTS MUST BE MADE BY 11:59PM ANY BUSINESS DAY FOR INSPECTION THE FOLLOWING City of W heat f� COMMUNITY DEVELOPMENT Building & Inspection Services Division 7500 W. 29th Ave., Wheat Ridge, CO 80033 Office: 303-235-2855 * Fax: 303-237-8929 Inspection Line: 303-234-5933 Email: permits(cki.wheatridge.co.us I FOR OFFICE USE ONLY I Date: Plan/Pennit # Plan Review Fee: Building Permit Application I Please complete all highlighted areas on both sides of this form. Incomplete applications may not be processed. *** Property Address: 3625 Chase St, Wheat Ridge, CO 80212 Property Owner (please print): Zack Magalei Phone: 720 495-3535 Property Owner Email: Mailing Address: (if different than property address) Address: State. Zip: Architect/Engineer: Architect/Engineer E-mail: Contractor: Home Depot USA Contractors City License #: 170102 Contractor E-mail Address: iamie(Qreedysetgo.com Sub Contractors: Electrical: W.R. City License # Other City Licensed Sub: City License # Plumbing: W.R. City License # Phone: Phone: 801 710-2507 Other City Licensed Sub: City License # Mechanical: W.R. City License # Complete all information on BOTH sides of this form ❑ COMMERCIAL 10rRESIDENTIAL Description of work: (Check all that apply) ❑ NEW COMMERCIAL STRUCTURE ❑ ELECTRICAL SERVICE UPGRADE ❑ NEW RESIDENTIAL STRUCTURE ❑ COMMERCIAL ROOFING ❑ COMMERCIAL ADDITION ElpRESIDENTIAL ROOFING ❑ RESDENTIAL ADDITION 19 WINDOW REPLACEMENT ❑ COMMERCIAL ACCESSORY STRUCTURE (Garage, shed, deck, etc.) ❑ RESIDENTIAL ACCESSORY STRUCTURE (Garage, shed, deck, etc.) ❑ MECHANICAL SYSTEM/APPLIANCE REPAIR or REPLACEMENT ❑ PLUMBING SYSTEM/APPLIANCE REPAIR or REPLACMENT ❑ ELECTRICAL SYSTEM/APPLIANCE REPAIR or REPLACEMENT ❑ OTHER (Describe) (For ALL projects, please provide a detailed description of work to be performed, including current use of areas, proposed uses, square footage, existing condition and proposed new condition, appliance size and efficiency, type and amount of materials to be used, etc.) Replace 7 windows like for like with retrofit vinyl windows, with a U -value .28 or better, according to manufacturer's specifications. Sq. Ft./LF Btu's Gallons Amps Squares Other Project Value: (Contract value or the cost of all materials and labor included in the entire project) $ 5241.00 OWNER/CONTRACTOR SIGNATURE OF UNDERSTANDING AND AGREEMENT I hereby certify that the setback distances proposed by this permit application are accurate and do not violate applicable ordinances, rules or regulations of the City of Wheat Ridge or covenants, easements or restrictions of record; that all measurements shown and allegations made are accurate; that I have read and agree to abide by all conditions printed on this application and that I assume full responsibility for compliance with applicable City of Wheat Ridge codes and ordinances for work tinder any permit issued based on this application; that I am the legal owner or have been authorized by the legal owner of the property to perform the described work and am also authorized by the legal owner of any entity included on this application to list that entity on this application. I, the applicant for this building permit application, warrant the truthfulness ofthe information provided on the application. CIRCLE ONE: (OWNER) (CONTRACTOR) or (AUTHORI2EWEPRESENTATIVE) of (OWNER) (CONTACTOR) Electronic Signature (first and last name): DATE: 10/9/17 ZONING COMMMENTS: Reviewer: BUILDING DEPARTMENT COMMENTS: Reviewer. DEPARTMENT USE ONLY OCCUPANCY CLASSIFICATION: Building Division Valuation: $ a ) � + � ( k ;f « ) k ! ) � � k \{ \ U) ) 8 _ ) ) ■ Lij CL - _ ,f - - } to } ; ) ! / ) � + ■ k k ) ( ) _ - _ - - ; ) ! / $ / ƒ } / } � ) 4 job �lo�s�i�31v A i CITY OF WHEAT RIDGE _:�9�Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax ❑ No one available for inspection: Time �� AM/PM Re -Inspection required: Yes No When corrections have been made, call for re -inspection at 303-234-5933 Date: , 0 - Inspector:. City of Wheat Ridge ..- HO Interior Remodel PERMIT - 201706628 PERMIT NO: 201706628 ISSUED: 09/11/2017 JOB ADDRESS: 3625 Chase ST EXPIRES: 09/11/2018 JOB DESCRIPTION: Homeowner remodel: Demo closet to join bedroom; Removal of water damaged drywall in laundry; Remove and replace kitchen cabinets; Replace bathroom vanities; Replace furnace 800 60K BTUs; approx. 1,000 sq ft *** CONTACTS *** OWNER (720)495-3535 MAGALEI STEFANIE NICOLE/ZACH *** PARCEL INFO *** ZONE CODE: UA / Unassigned USE: UA / Unassigned SUBDIVISION CODE: 2412 / LAKESIDE, STEWART GARDENS, OLI BLOCK/LOT#: 0 / *** FEE SUMMARY *** ESTIMATED PROJECT VALUATION: 25,000.00 FEES Total Valuation 0.00 Plan Review Fee 287.33 Use Tax 525.00 Permit Fee 442.05 ** TOTAL ** 1,254.38 *** COMMENTS *** *** CONDITIONS *** I, the property owner, by my signature, attest that I currently reside at the project property, intend to reside at the property for a period of one year after completion of the project, and am personally performing all work, without the assistance of hired or professional workers. Consultations and inspections will only be performed with the homeowner of record present. All roughs to be done at Framing Inspection. Approved per plans and red -line notes on plans. Must comply with 2012 IRC, 2014 NEC and all applicable City of Wheat Ridge Municipal Codes. Work is subject to field inspections. PERMIT NO: JOB ADDRESS: JOB DESCRIPTION City of Wheat Ridge HO Interior Remodel PERMIT - 201706628 201706628 3625 Chase Homeowner drywall in vanities; ST ISSUED: EXPIRES: remodel: Demo closet to join bedroom; laundry; Remove and replace kitchen Replace furnace 80% 60K BTUs; approx. 09/11/2017 09/11/2018 Removal of water damaged cabinets; Replace bathroom 1,000 sq ft I, by my Is do hereby attest that the work to be performed shall comply with all accompanying approved plans and specifications applicable building codes, and all applicable municipal codes, policies and procedures, and that I atn the legal owner or have been authorized by the legal owner of the property and am authorized to obtain this permit and perform the work described and approved in conjunction with this permI I furthe I am legally authorized to include all entities named within this document as parties to the work to be performed a at all-rW k to erform d is disclosed in this document and/or its' accompanying approved plans and specifications. Signature of OWNER CONTRACTOR (Circle one) Date I. This permit was i ued ba ed on the information provided in the permit application and accompanying plans and specifications and is subject to the com ith those documents, and all applicable statutes, ordinances, regulations, policies and procedures. 2. This permit shall expire 365 days after the date of issuance regardless of activity. Requests for extension must be made in writing and received prior to the date of expiration. An extension of no more than 180 days made be granted at the discretion of the Chief Building Official and may be subject to a fee equal to one-half of the original permrt fee. 3. If this permit expires, anew permit may be required tot obtained. Issuance of a new permit shall be subject to the standard requirements, fees and procedures for approval of any new permit. Re -issuance or extension of expired permits is at the sole discretion of the Chief Building Official and is not guaranteed. 4. No work of any manner shall be performed that shall results in a changeof the natural flow of water without prior and specific approval. 5. The permit holder shall notify the Building and Inspection Services Division in accordance with established policy of all required inspections and shall not proceed or conceal work without written approval of such work from the Building and Inspection Services Division, 6. The issuance or granting of a. grmit s ajl t be construed to be a permit for, or an approval of, any violation of any provision of any applicableQW-.' r arly.ordinar ce. u�• a on of this jurisdiction. Approval of work is subject to geld inspection. 5I'rf ,� Signature of Chief Building Official Date REQUESTS MUST BE MADE BY 11:59PM ANY BUSINESS DAY FOR INSPECTION THE FOLLOWING BUSINESS DAY. City of __L�;rWheat �idge COMMUNiTy DEVELOPMENT Building & Inspection Services Division 7500 W. 29th Ave., Wheat Ridge, CO 80033 Office: 303-235-2855 * Fax: 303-237-8929 Inspection Line: 303-234-5933 Email: permits@ci.wheatridge.co.us FOR OFFICE USE ONLY Date: / 7 Plan/Permit # lv — ^ Plan Review Fee: Building Permit Application *** Please complete all highlighted areas on both sides of this form. Incomplete applications may not be processed. **' Property Address: ,`& G z- .:�7 c W 'z.. -R,. cu . $G2 I Z Property Owner (please print):S �A,�,_ ,q�h� Phone: -y zo- 49 S-• 3S- 3� Property Owner Email: Mailing Address: (if different than property address) Address: 1---i lel A L -JI t coxi S —i - City,. City, State, Zip: -T-jq o g_„lZA/. G b i.4) I Architect/Engineer: Architect/Engineer E-mail: Phone: Contractor: Contractors City Lidense #: Contractor E-mail Address: Sub Contractors: Electrical W.R. City License # Other City Licensed Sub: City License # Plumbing: W.R. City License # Phone:_ t Other City Licensed Sub: City License # Mechanical: W.R. City License # Complete all information on BOTH sides of this form ❑ COMMERCIAL W RESIDENTIAL Description of work: (Check all that apply) ❑ NEW COMMERCIAL STRUCTURE ❑ ELECTRICAL SERVICE UPGRADE ❑ NEW RESIDENTIAL STRUCTURE ❑ COMMERCIAL ROOFING ❑ COMMERCIAL ADDITION ❑ RESIDENTIAL ROOFING ❑ RESDENTIAL ADDITION ❑ WINDOW REPLACEMENT ❑ COMMERCIAL ACCESSORY STRUCTURE (Garage, shed, deck, etc.) ❑ RESIDENTIAL ACCESSORY STRUCTURE (Garage, shed, deck, etc.) ❑ MECHANICAL SYSTEM/APPLIANCE REPAIR or REPLACEMENT ❑ PLUMBING SYSTEM/APPLIANCE REPAIR or REPLACMENT ❑ ELECTRICAL SYSTEM/APPLIANCE REPAIR or REPLACEMENT ® OTHER (Describe) � NV AJ i . v �a� �� J� r izATf (For ALL projects, please provide a detailed description of work to be performed, including current use of areas, proposed uses, square footage, existing condition and proposed new condition, appliance size and efficiency, type and amount of materials to be used, etc.) �S*,. , op c�f- f,.. q-t-� � � 14�A;q �� t� � y/ �,.A `` [ nl c- h �.�! ►� r� `i . t� �a�,�r � � JZ 1� L 1�-� i.v�y tL . iz r[ � f C'Af3rnf Sq. Ft./LF Amps Btu's L G_ Gallons Squares Other Project Value: (Contract value or the cost of all materials and labor included in the entire project) OWNER/CONTRACTOR SIGNATURE OF UNDERSTANDING AND AGREEMENT I hereby certify that the setback distances proposed by this permit application are accurate and do not violate applicable ordinances, rules or regulations of the City of Wheat Ridge or covenants, easements or restrictions of record; that all measurements shown and allegations made are accurate; that I have read and agree to abide by all conditions printed on this application and that I assume full responsibility for compliance with applicable City of Wheat Ridge codes and ordinances for work under any permit issued based on this application; that 1 am the legal owner or have been authorized by the legal owner of the property to perform the described work and am also authorized by the legal owner of any entity included on this application to list that entity on this application. I, the applicant for this building permit application, warrant the truthfulness of the information provided on the application. CIRCLE ONE:NER (CONTRACTOR) or Signature (first and last name): ZONING COMMMENTS: Reviewer: BUILDING DEPARTMENT COMMENTS: Reviewer: �I r3=>Ir7 6 THORIZED REPRESENTATIVE) of (OWNER) (CONTRACTOR) DATE: 5�—' PARTMENT USE ONLY OCCUPANCY CLASSIFICATION 123 , 1CCMI4E0 9,10M00f(- - M.)Nn2 -4 151141(D-00 9A7k i W City of Wh6atidj ! gle COMMUNITY DEVELOPMENT Official Certification of Property Owner Permit THIS IS TO CERTIFY that I, the property owner, by my signature, attest that I currently reside at the project property, or intend to reside at the property for a period of one year after completion of the project, and am personally performing all work, without the assistance of hired or professional workers, or, if hiring sub -contractors, list them on the permit. Consultations and inspections will only be performed with the homeowner of record present at the project property. Property Owner(s):-1 --\- Project Property: 71,ZS GN Ptd S_ti, 1j� CG 2 - Notarized Notarized signature of nt State of Colorado " ) County of k dl',� 50Y, ) ss The foregoing instrument was acknowledged by me this cOil ,,--7 day of 0AJr14L_, 2017by ZMQQ_k JAYMESUE MCRIMMON NOTARY PUBLIC STATE OF COLORADO NOTARY ID # 20154009457 h1Y COMMISSION EXPIRES MARCH 06, 2019 My Commission Expires/�20Lg Public 5366 Godding Hollow Parkway Longmont, 0RTH ENERGYENVIRONMENT (E3) Local: 303.4778-0922 Industrial Hygiene and Environmental Engineering August 18, 2017 Mr. Zach Magalei Home Owner 3625 Chase Street Wheat Ridge, CO 80212 Subject: Asbestos Sampling Results — 3625 Chase Street in Wheat Ridge, CO 80212 Dear Mr. Magalei: On August 15, 2017, an Industrial Hygienist with Earth Energy Environment (E3) performed an inspection and asbestos sampling at the residential property located at 3625 Chase Street in Wheat Ridge, CO 80212. E3 was retained by the property owner to determine if select areas within the interior area contain asbestos. Only materials that were disturbed and miscellaneous wall and ceiling debris in the work area were sampled. SURVEY METHODOLOGY An industrial hygienist from E3 conducted the sampling. Materials were grouped into homogeneous sampling areas based on the material type. Among the interior building materials, one (3) distinct homogeneous area within the property was identified and sampled. No other building materials were sampled. Homogeneous Material Classifications ■ A preliminary walk through of the buildings was conducted to determine areas of materials which were visually similar in color, texture, general appearance, and which appeared to have been installed at the same time. Such materials have been termed "homogeneous materials" by the EPA. During this walk through, the approximate locations of these homogeneous materials were noted. ■ Following the EPA inspection protocol, each identified suspect homogeneous material was placed in one of the following EPA classifications: o Surfacing Materials - Sprayed or troweled on surfaces (walls, ceilings, structural members) for acoustical, decorative, or fireproofing purposes. This includes plaster and fireproofing insulation. o Miscellaneous Materials - Other non -friable products and materials such as floor tile and ceiling tile. o Thermal System Insulation - Insulation used to inhibit heat transfer or prevent condensation on pipes, boilers, tanks, ducts, and various other components of hot and cold water systems and heating, ventilation, and air conditioning (VAC.) systems. This includes pipe lagging, pipe wrap, block, batt, blanket insulation, cements, muds, gaskets and ropes. (These materials were not sampled as part of the survey.) Friability Classifications Friable and non -friable ACM's are defined as follows: ■ Friable asbestos -containing material: any material containing more than 1% asbestos, determined using PLM analysis, that when dry, can be crumbled, pulverized, or reduced to powder by hand pressure. ■ Category I nonfriable asbestos -containing material: asbestos -containing resilient floor covering, mastic or asphalt roofing product containing more than 1% asbestos as determined using PLM. ■ Category II nonfriable asbestos -containing material: any material, excluding Category I non -friable ACM, containing more than I% asbestos as determined using PLM that, when dry, cannot be crumbled, pulverized, or reduced to powder by hand pressure. ■ Regulated asbestos -containing material (RACM): (1) friable ACM, (2) Category I nonfriable ACM That has become friable, (3) Category I nonfriable ACM that will be or has been subjected to sanding, grinding, cutting, or abrading, or (4) Category II nonfriable ACM that has a high probability of becoming or has become crumbled, pulverized, or reduced to powder by the forces expected to act on the materials in the course of demolition or renovation operations. Sampling and Laboratory Analysis Bulk samples were collected by using various sampling tools (cutting tools, knives and chisels) to cut away or scrape portions of suspect building materials into zip -sealed plastic bags or sampling tubes. The individual samples were labeled by material type and location. Samples were analyzed by Reservoirs Environmental Laboratory located in Denver, CO. The laboratory maintains accreditations through the American Industrial Hygiene Association (AIHA), and National Voluntary Laboratory Accreditation Program (NVLAP). The analysis performed was EPA Method 600/R-93/116. INSPECTION RESULTS E3 collected at least the minimum number of samples from each homogeneous area necessary to meet all regulatory requirements for the quantity of material to be observed. Table 1 provides a summary of the homogenous areas. Table 1. Homogeneous and Functional Sampling Areas. The laboratory separated and analyzed individual layers within each sample, if present. According to the laboratory analysis of the materials sampled, trace asbestos was detected in the plaster walls and the hall wall areas. Table 2. Asbestos Containing Materials HA Material Type Material Physical Classification Samples HA Material Type Description Description Collected Wall Trace Chrysotile A Off white granular plaster Cuts System 1 Hall Wall Wall B Off white plaster w/ Surfacing 1 Cuts System Materials Plaster Wall white/multi-colored paint 1 race Chrysotile 3 Walls System C White plaster w/ off white A Off white granular plaster 2 Floor Misc. Misc. 3 Debris Debris B White plaster Materials A White compound Plaster Wall B Off white granular plaster Surfacing 3 Walls System Materials 3 C White plaster w/ off white paint The laboratory separated and analyzed individual layers within each sample, if present. According to the laboratory analysis of the materials sampled, trace asbestos was detected in the plaster walls and the hall wall areas. Table 2. Asbestos Containing Materials HA Material Type Material Description Physical Description Asbestos Content A Off white granular plaster Hall Wall Wall Trace Chrysotile 1 Cuts System B Off white plaster w/ 0.25% Chrysotile) white/multi-colored paint A White compound Plaster Wall B Off white granular plaster 1 race Chrysotile 3 Walls System C White plaster w/ off white <' 0.25% Chrysotile; paint 41 i . OSHA regulations will apply to the trace materials. OSHA Asbestos Regulations are stated in 29 CFR 1926.1101 and must be followed when the materials are disturbed by a contractor through renovation, demolition, or other types of disturbances. The requirements for contractors working in the areas with trace levels of asbestos are paraphrased below. • Notification to all personnel involved with any disturbances regarding the percentage of asbestos in the building materials. • Use of limited engineering controls, such as wet -methods, designed to eliminate dust -to - air as the material is disturbed. • Personal air monitoring during periods of disturbances to ensure applicable permissible exposure limits are no exceeded. CONCLUSIONS AND RECOMMENDATIONS According to the laboratory analysis of select interior building materials, trace asbestos was detected in the plaster walls and the hall walls. The Colorado Department of Public Health and the Environment does not regulate trace levels of asbestos. OSHA regulations will apply to the trace materials Any potential asbestos containing materials identified in the future or during demolition that were not sampled in this, or any other previous survey, should be tested for asbestos content or assumed to contain asbestos before being disturbed. If you have questions or require additional information, please contact me at (303) 902-5851. Sincerely, Art Willden Certified Building Inspector No. 20138 Attachment A Laboratory Testing Results Reservoirs Environmental, Inc. Effective January 1, 2015 Reservoirs Environmental QA Manual T:\QAQC\Lab\Reservoirs Environmental QA Manual.doc REI LAB Reservinirs Environmental, Inc. August 16, 2017 Eli Willden Earth Energy and Environment Corp. 5366 Godding Hollow Pkwy Longmont CO 80504 Dear Customer, Subcontract Number: NA Laboratory Report: RES 387293-2 Project # / P.O. # None Given Project Description: None Given Reservoirs Environmental, Inc. is an analytical laboratory accredited for the analysis of Industrial Hygiene and Environmental matrices by the National Voluntary Laboratory Accreditation Program (NVLAP), Lab Code 101896-0 for Transmission Electron Microscopy (TEM) and Polarized Light Microscopy (PLM) analysis and the American Industrial Hygiene Association (AIHA), Lab ID 101533 - Accreditation Certificate #480 for Phase Contrast Microscopy (PCM) analysis. This laboratory is currently proficient in both Proficiency Testing and PAT programs respectively. Reservoirs Environmental, Inc. has analyzed the following samples for asbestos content as per your request. The analysis has been completed in general accordance with the appropriate methodology as stated in the attached analysis table. The results have been submitted to your office. RES 387293-2 is the job number assigned to this study. This report is considered highly confidential and the sole property of the customer. Reservoirs Environmental, Inc. will not discuss any part of this study with personnel other than those of the client. The results described in this report only apply to the samples analyzed. This report must not be used to claim endorsement of products or analytical results by NVLAP or any agency of the U.S. Government. This report shall not be reproduced except in full, without written approval from Reservoirs Environmental, Inc. Samples will be disposed of after sixty days unless longer storage is requested. If you have any questions about this report, please feel free to call 303-964-1986. Sincerely, Jeanne Spencer President P: 303-964-1986 F: 303-477-4275 5801 Logan Street, Suite 100 Denver, CO 80216 Page 1 of 1 1-86&RESI-ENV wauw.reilab.com U 2 � � 2 w 2 2 0 > 2 w � LLI � � U) w w \0 }} 9 k CD0 \ z z LI 0 0 0 0 � 0 0 0 0 0 0 � 00 00 0 CO } /. n 0 � 2 ) £ .> g \ _% ® § E z0 k 0 z \\a ®$ > \ ` E O a. nm & w \)) a ®� 2 LU � L) I C) Lcu o Lu CD 2 k7§&�2 o / e � � 2 ± - a 0 0 0 0 0 mw�o$$�co LU U ° ■ w�zz<w2� a a '2 ) 7{ a 0 0 0 0 � 0 0 0 0 0 0 0 0 00 00 0 CO z /. 2 � 2 ) £ .> g E § ) _% ® b = z0 k 0 z \\a ®$ r r E ` E � \ ��U)0 nm m e \)) a ®� 2 LU � 0 C) Lcu o '2 ) 7{ a 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 00 00 0 CO & E 0 §« g f y o 0 0 0 0 0 0 0 0 0 0 y7er� 2ƒ& E / � 2 :R. o o a Ot&0 o c■ m a I --c4 z z z z z� z z e� z ;_ C4 v 2 o LLJ Q ---- 2 \ 2 \ $ 0 3 2 v � 0 \ f \ f \ Q% = 2 o a o a Q a a/$ $� G g 2 m f g S R m S k k k 2 �.2 - k ƒ_ /_ L / \ 2 \ a CL cu EL k \ \ 7 k ) § $ $ k $ & k $ « 5 o m m 0) 0)D E 3 ) t f CL OL a 8 f CL \%\* 3 3 0 3\ 3 3 \ \ 0 \ �« u W< m< m«_« m« m o C14 LO n LO 2 k 0 \ \ 0 § / k k \ w 3 g 3 w 3 \ \ \ \::3 3 3 m SEE \ \ - kU)z ƒ } } ƒ ƒ §§ )( § }\ U 2 � � 2 w 2 2 O � > 2 w CO O � w U) LU w 9 2 � cff� . Lu w a\0 \\ |e a F- 10 1a K # zeE 1612 jZM— )( P z2) k \ ƒ& E ci 7 § a 0) o 0 � \ 0 n < E Q . z 2 � �a�o■m ) § J z © § I k �w & u a 0w Q........... \ ] C �a o jj c� Cpm 00 a Q e§& L6 J 2;±±�8 § c z Gow6u �o$$�« � a. m ƒ L) w (( 2 m LU w w mo - z z« w« LU & :L \ 0 C % ■ \ � $ \ E kf E z / .. u<»wW «m �. \ ) £ ± � 2 E § ) _% c Q = z0� \@ § CL} \\k E r E` ®k E w j a L m a J$ m nk)����0 * ƒdC)C)0 k )( P z2) k \ ƒ& E ci 3 § a 0) o 0 2$§§� \ < E 3 �a�o■m \ ; . z 7 40 k �w \ 0w Q........... \ � \ § _ = o 00 / f § 0 B Q a � a. $G ƒ j¥ Z \ & \ \ 0 % \5 \ $ \ E kf E aƒ k \0 u<»wW «m LO � 00 § cli � k � \@ § $ �� \ * k SEE ) §22 )( P \ ci \ _ 2 \ k R \ $ 7 \ § a \ E / ƒ » \ & \ \ E E k ƒ k � $ �� City of r W heat j , dgce COMMUNITY DEVELOPMENT PL94�F SFE H [ 6-� U G sc cDwl w Ml e- Iq / f 4)0V( --Y7-0 City of Wheat Ridge Municipal Building 7500 W. 29`b Ave. Wheat Ridge, CO 80033-8001 P: 303.235.2855 F: 303.237.8929 Review is limited to the contents of the plans submitted and any errors or omissions contained herein shall not be construed as permission to allow any conditions to exist in violation of the codes of the City of Wheat Ridge 3 As part of the foundation inspection and PRIOR TO THE FIRST FRAMING INSPECTION, a completed, signed and sealed, Foundation Setback and Elevation Certification shall be submitted to the City for review. The certification form shall be fully completed by a Professional Land Surveyor licensed in the state of Colorado, stating that the foundation was constructed in compliance with all applicable minimum setback and elevation requirements to the city. 4 Burial depth requirements: Electrical - direct burial conductors shall be a minimum of 24 -inches deep, non-metallic conduit 18 -inches deep or 24 -inches under driveways. (IRC Table E3803.1) Water Lines - shall be a minimum of 36 -inches deep. (IRC P2603.6) Gas Service Piping - installed a minimum of 12 -inches below grade or 8 -inches below grade where serving individual outside appliances. An 18 AWG yellow insulated tracer wire must be installed adjacent to underground nonmetallic gas piping and terminate above grade at each end. (IRC G2415.1.2 and G2415.17.3) 5 Underground plumbing pipe shall have a solid and continuous load-bearing support. Piping cannot bear on rocks. Pipes passing under a footing or through foundation wall shall be provided with a relieving arch or a sleeve. Trenches parallel to footing shall not extend below the 45° plane of the edge of the footing. Water piping must be buried a minimum 36 -inches deep. Water service pipe may be installed in the same trench as the building sewer provided the sewer pipe material is listed for underground use within the building or the water service pipe is separated from the sewer by a minimum distance of 5 -feet horizontally or elevated at least 12 -inches above and to one side of the sewer line. 6 Frost depth to the bottom of the foundation footings must be as noted on the engineered plans. If not noted, the frost depth to the bottom of the footings must be a minimum of 30 -inches below finished grade. (IRC TableR301.2.1) 7 Caisson and helical pier foundations will not be inspected by Boulder County. A qualified, Colorado -licensed engineer must perform the placement, drilling, and reinforcement of drilled piers. A signed, sealed and dated inspection report must be provided to Building Inspection Services prior to the rough inspections R110.5.2.3) 8 A perimeter drain system that discharges to an approved drainage system is required around all foundations that enclose usable spaces below grade. Foundations that retain earth and enclose interior spaces below grade must be damp proofed. (IRC R405.1, R406.1) cny or 9 Slabs below grade must maintain a minimum of 6 -inches above the design water table. The i el WefW' b d crawl space grade must be a minimum of 36 -inches above the design water table.( R401.2.1.3an &,91.2.1.5 10 Garage floor surfaces must be approved noncombustible materials. Floors must be sloped to fac movement of liquids to a drain or toward the main vehicle entry doorway. (IRC R309.1) 11 Foundation plates and sills must be bolted to the foundation wall as prescribed on the engineered plans. If not noted, bolts shall have a minimum diameter of %-inch, embedded at least 7 -inches and spaced not more than 6 -feet apart. A minimum of 2 bolts are required per plate section, with one bolt located within 12 -inches of each end of each plate. (IRC R403.1.6) Rough Framing and Wood Requirements 12 The complete rough inspection is to be made after the rough framing, rough electric, rough plumbing, and rough heat and ventilation are complete. The building should be fully enclosed with the roof covering and siding in place. 13 Protection from decay shall be provided in the following locations by the use of naturally durable wood or wood that is preservative treated in accordance with AWPA U1: (IRC R317) 14 Lumber, plywood, fiberboard, structural logs, and glued laminated timber must be identified by a grade mark or certificate of inspection issued by an approved agency. (IRC R502.1, R602.1, and R802.1) A. Wood joists closer than 18 -inches and wood girders closer than 12 -inches to grade located within foundation periphery.B. Wood framing members that rest on concrete or masonry foundation walls and are less than 8 - inches from the exposed ground. C. Sills and sleepers on a concrete or masonry slab that is in direct contact with the ground. D. Wood girders entering concrete or masonry walls with a clearance less than %-inch. E. Wood siding, sheathing, and wall framing less than 6 -inches above the ground. F. Wood members supporting moisture -permeable floors or roofs that are exposed to the weather. G. Wood furring strips or wood members attached directly to the interior of below grade exterior masonry or concrete walls. H. Wood in contact with the ground, embedded in concrete in direct contact with the ground or embedded in concrete exposed to the weather that supports permanent structures intended for human occupancy shall be approved pressure -preservative -treated wood. 1.3 Accessible under -floor areas shall be provided with a minimum 18 -inches x 24 -inches opening through the floor or 16 -inches x 24 -inches opening through the perimeter wall. When the access is through a below -grade wall an areaway of not less than 16 -inches x 24 -inches must be provided. Where equipment is located beneath the floor, the access opening must be within 20 -feet of the equipment and allow the removal of the largest piece of equipment. (IRC R408.4 and M1305.1.4) 14 Basements greater than 200 square feet and every sleeping room shall have at least one operable emergency and rescue opening or a door to the exterior. /"— cny of 15 Emergency escape and rescue openings shall meet the following requirements: A minimu clear width o heat Rid e 20 -inches, a minimum clear height of 24 -inches, with a total net clear opening of 5 square fetor gra de IOeve windows and 5.7 square feet for all others. A sill height of not more than 44 inches measured i�i'4lh�"fiiii ed floor to the bottom of the clear opening. Window wells for emergency escape and rescue shall provide a minimum net area of 9 square feet with minimum horizontal projection and width of 36 -inches. The area of the widow well shall allow the emergency escape and rescue opening to fully open. (IRC R310) 1.6 Columns must be restrained to prevent lateral displacement at the bottom end to insure against uplift. (IRC R301.2.1, R407.3) 17 Fire blocking shall be installed to cut off all concealed draft openings in the following locations: (IRC 302.11) A. In concealed spaces of stud walls and partitions, including furred spaces, vertically at the ceiling and floor levels, and at 10 -feet horizontal intervals. B, At interconnections between concealed vertical and horizontal spaces such as occur at soffits, drop ceilings, and cove ceilings. C. In openings around vents, pipes, ducts, cable, wires, chimneys, fireplaces, and similar openings that afford a passage for fire at ceiling and floor levels. D. In concealed spaces between stair stringers at the top and bottom of the run, and between studs in line with the run of the stairs at unfinished walls. 18 At least one egress door shall be provided for each dwelling unit. The egress door shall be side -hinged, and shall provide a minimum clear width of 32 -inches (813 -mm) when measured between the face of the door and the stop, with the door open 90 degrees (1.57 rad). The minimum clear height of the door opening shall not be less than 78 -inches (1981 -mm) in height measured from the top of the threshold to the bottom of the stop. Other doors shall not be required to comply with these minimum dimensions. Egress doors shall be readily openable from inside the dwelling without the use of a key or special knowledge or effort. (IRC R311, R311.2) 19 There shall be a floor or landing on each side of each exterior door, except where a stairway with 2 or fewer risers located on the exterior side of the door, other than the required exit door, a landing is not required for the exterior side of the door. The landing must be no lower than 73/ -inches below the top of the threshold of the door provided the door does not swing over the landing. (IRC R311) 20 Stairways must be at least 36 -inches in width. Handrails shall not project more than 4% -inches. The maximum rise may not exceed 7% -inches. The minimum tread depth may not be less than 10 -inches. Minimum headroom is 6 -feet, 8 -inches. For stairways with solid risers a nosing of %-inch to 1% -inches shall be provided. When open risers are used the opening between the treads shall not allow the passage of a 4 -inch sphere to pass through. Landings must be provided at the top and bottom of the stairway that is the width of the stairway measuring at least 36 -inches in the direction of travel. Handrails shall be provided on at least one side of stairways with 4 or more risers and ramps with a slope exceeding 1:12. Handrails shall be mounted 34 -inches to 38 -inches above the nosing of the treads. Handrails must be continuous for the entire length of the stairs and provided with a minimum space of 1% -inch between the wall and the handrail. Ends shall be returned or terminate in newel posts or safety terminals. See the requirements and more information. (IRC R311.7.8.2) 21 Handrail Grip Size Shall Be:A. Circular Handrails: 1% -inch to 2 -inches perimeter. B. Non -Circular: ' s to 6% -inches perimeter with a maximum cross section of 2Y4 -inches. C. Perimeter Dimension GreU3pen inches: shall have a finger recess on both sides. 22 Guards must be provided for porches, screened porches, balconies, fixed seating and ras more than 30 -inches above the floor or grade below. Guards must have a minimum height o sides of stairs with a total rise of more than 30 -inches above the floor or grade below shall have guards not less than 36 -inches high. Intermediate rails shall not allow the passage of a 4 -inch sphere. (R312) Window fall protection must be provided for window openings less than 24 inches above the finished floor and more than 72 inches above grade or surface below. (R312.2) 23 Ceiling heights for habitable rooms, hallways, bathrooms, toilet rooms, laundry rooms, and basements shall be a minimum of 7 -feet measured from the finished floor to the lowest projection of the ceiling. Non -habitable basements may have a ceiling height of 6 -feet, 8 -inches with clearance below beams and ducts of 6 -feet, 4 - inches. Bathroom may have a ceiling height of 6 -feet, 8 -inches at the fixture front clearance area and over the fixture. (IRC R305.1) 24 Attic access must be provided for attics that exceed 30 square feet and that have a vertical height of 30 - inches or greater. The access must be located in a hall or readily accessible location with a minimum 22 -inches x 30 -inches access opening. The access must provide a minimum of 30 -inches headroom. (IRC R807) 25 Enclosed attic and rafter spaces must have cross ventilation for each space through screened openings. The total net free ventilating area shall not be less than 1 to 150 of the area of the space ventilated. The area may be reduced to 1 to 300 if 50-80% is provided by ventilators located in the upper portion of the space or if a vapor barrier not exceeding 1 perm is installed on the warm side of the ceiling. At least a 1 -inch space is required between the roof sheathing and the insulation at the location of the vent. (IRC R806) 26 Rafters must be framed to a minimum 1 -inch nominal ridge board that is not less than the depth of the cut end of the rafter or to each other using a gusset plate. Hip, and valley rafters shall be a minimum of 2 -inches and not less in depth than the cut end of the rafter. Hip and valley rafter shall be supported at the ridge by a brace to a bearing partition or be designed. (IRC R802.3) 27 Rafters and ceiling joists having a depth -to -thickness ratio exceeding 5:1 shall be provided with lateral support at points of bearing to prevent rotation. Rafters and ceiling joists having a depth -to -thickness ration exceeding 6:1 shall be supported laterally by solid blocking, diagonal bridging or a continuous 1 -inch by 3 -inch wood strip nailed across the rafters. (IRC R802.8) Roof trusses or rafters must be attached to supporting walls with approved hurricane clips. Trusses must be braced to prevent rotation and to provide lateral stability in accordance with the construction documents and the individual truss design drawings. (IRC R502.11.2, R802.11) 28 Trusses must be designed and fabricated in accordance with ANSI/TPI 1. A licensed professional shall prepare the truss design. Trusses must be legibly marked within 2 -feet of the center to identify the manufacturer, the design load, and the spacing. Truss engineering and layout must be provided at the site at the rough framing inspection. (IRC R502.11 and R802.10) 29 Roofing material installed in the mountain areas is limited to Class -"A" roof coverings. Wood roofs in the plain areas are limited to minimum Class "B" roof coverings. Shingle installation shall meet the manufacturer's high -wind installation procedures in areas where wind load is greater than 105 mph 3 sec gust( R301.2.1, R325). 30 All habitable rooms shall be provided with aggregate glazing area for natural light of not lOdash�ff. he floor area of such rooms. The glazed areas need not be installed in rooms where section (M1d and artificial light is provided at an average of 6 foot candles at a height of 30 inches. e 31 Safety glazing shall be installed in the following hazardous locations and be permanently IS y or tempered glazing: glazing panels in doors; glazing enclosing spas, bathtubs or showers; glazing panels adjacent and within 24 -inches of the edge of a door; glazing panels greater than 9 square feet within 18 -inches of the floor; glazing used for railings; glazing used for barriers for swimming pools and spas; and glazing enclosing stairways, landings, and ramps within 36 -inches horizontally of a walking surface. See the Boulder County Land (IRC R308) 32 Roofs decks and enclosed roofed areas must be provided with roof drains installed at the low point of each roof. Where roof drains are installed, overflow drains or scuppers are required. (IRC R903.4) 33 Exterior finish materials must conform to the conditions of your Site Plan Review to include: roof covering, siding, ignition resistant construction, color requirements, conforming light fixtures which comply with the approved lighting plan, and re -vegetation requirements. Glazing and Window Requirements 32 Skylights must be: (IRC R308.6 Table N1102.1) A. laminated glass (with restrictions). B. fully tempered glass (with retaining screen). C. Skylight U -factor required U-0.45. Skylights installed on roofs flatter than 3 units vertical to 12 units horizontal must be mounted on a curb 4 -inches above the roof. Heating and Ventilation Requirements 33 Crawl spaces shall be provided with conditioned air in compliance with Section N1102.2.9. Crawl space walls shall be insulated in accordance with Table N1102.1 or Table N 1102.1.2. Crawl space wall insulation shall be permanently fastened to the wall and extend downward from the floor to the finish grade level and then vertically and/or horizontally for a least an additional 24 -inches. Exposed earth in unvented crawl space foundations shall be covered with a continuous Class I vapor retarder with a minimum thickness of 10 -mil. All joints of the vapor retarder shall overlap by 6 -inches and be sealed and taped. The edges of the vapor retarder shall extend at least 6 -inches up the stem wall and shall be attached to the stem wall. N1102.2.9.2.2 Ventilated crawlspaces. Ventilated crawlspaces shall be provided with insulation in accordance with Table N1102.1. 34 A Habitable rooms must be provided with outdoor openings for ventilation equal to at least 4% of the floor area and shall have heating facilities capable of maintaining 68` at 3 -feet above the floor and 2 -feet from exterior walls. B. The windows need not be openable in a room where an opening is not required to be an egress window and a mechanical ventilation system is capable of producing 0.35 air change per hour in that room, or a whole house mechanical ventilation system provides 15 cubic feet of outdoor air per minute. 35 Bathroom exhaust fans shall exhaust directly to the exterior and must be provided in bathrooms where windows of at least 3 square feet are not provided. The mechanical ventilation must be capable ofDithe exhaust capacity of 50 cfm intermittent or 20 cfm continuous exhaust. (IRC R303.3, M1507.4) 0 36 Dryer vents must be rigid metallic, independent of all other systems, shall terminate outsi * equipped with a back draft damper, and sized and terminated per the manufacturer. The maxi u � the exhaust duct shall be 35 -feet (Unless approved under the manufacturer's listing) from the con e transition duct from the dryer to the outlet terminal. Where fittings are used, the maximum length of the exhaust duct shall be reduced in accordance with (IRC Table M1502.4.4.1) Flexible transition ducts are limited to 8 -feet, shall not be concealed within construction, and shall be listed and listed per UL 2158A. (IRC M1502) 37 Appliances and equipment shall be installed in accordance with the conditions of their listing. Manufacturer's installation instructions must be available at the time of the inspection. (IRC G2408.1, M1307.1, M 1401.1, (M 1902.2) 38 Appliances shall be accessible for inspection, service, repair and replacement without removing permanent construction. 30 -inches of working depth and width shall be provided in front of the control side of an appliance. (IRC M1305.1) 39 Gas and solid fuel appliances located in a garage and hazardous locations shall be elevated so the source of ignition is at least 18 -inches above the floor. Rooms and spaces that are communicate directly with the garage and are not part of the living space shall be considered as part of the garage. Appliances located in garages must be installed at least 6 -feet above the floor or protected from motor vehicle impact. (IRC G2408.2, G2408.3) 40 Combustion air is required for all liquid fuel, solid fuel and gas appliances. (IRC M1701.1, G2407) 41 Gas burning appliances may not be located in or obtain combustion air from: a sleeping room, bathroom, toilet room, or storage closet unless it is a direct vent appliance or installed in an enclosure that opens only into a bedroom or bathroom in and such enclosure is provided with a solid weather-stripped door, a self-closing device and all combustion air is taken from the outdoors. (IRC G2406.2) 42 Gas logs installed in solid fuel burning fireplaces shall be tested in accordance with ANSI 221.60 and installed per the manufacturer's installation instructions. Gas logs installed in bedrooms must be direct vent or provided with an approved source of outside combustion air. The approved gas log set must be installed in the Solid -fuel burning appliances at the final inspection. (IRC G2406, G2432, and G2434) 43 B, BW, and L vents and factory -built chimneys must be provided with a clearance to combustibles per them a manufacturer's listing. Where vents pass through insulated assemblies, they must be provided with an insulation shield. A clearance of 9 -inches is required between single wall vent connectors and combustibles. Gas vents must penetrate through the roof flashing, jack or thimble and terminate in a Chimneys listed cap or per the manufacturers listing. Decorative shrouds installed at terminations shall be listed and installed per the manufacturer. (IRC G2425, G2426, G2427) Electrical Requirements 44 All electrodes present at each structure shall be bonded together to form one grounding electrode system to include: Concrete Encased Electrodes (UFER), water piping, ground rings, grounding rods, andpla electrodes. Bonding shall ensure electrical continuity. The electrode conductor must be connec tea in SO -11' � approved manner and inspected prior to concealing. (IRC E3607, E3608, E3609, E3610, E3611) tiFtAge 45 All hot, neutral, and grounding conductors in electrical boxes shall be tied together with a mec �`v�s�r, C1�a'i`rt' connection at the time of rough inspection. 46 Recessed lighting fixtures must either be IC -rated or installed in a sealed box in which the insulation is at least 3 -inches from the light fixture. All recessed lights must be tightly sealed or gasketed to prevent air leakage through the fixture into the ceiling cavity. (IRC N1102.4.5) 47 Tamper -resistant Receptacle outlets are required in every kitchen, family room, dining room, living room, parlor, library, den, sunroom, bedroom, recreation room or similar dwelling areas spaced so that no point along the wall line exceeds 6 -feet from an outlet. (IRC E3901, E3902, and 4002.1-4002.14)A Counters 12 -inches in width or wider shall have receptacles placed no more than 20 -inches above the counter top and spaced so no point exceeds 24 -inches from an outlet. B Island and peninsula counters with a length at least 24 -inches and a width of 12 -inches or greater must be equipped with at least one outlet. C. At least one receptacle shall be installed in a bathroom within 36 -inches of each basin. D. A least one receptacle outlet must be installed in each laundry, basement, attached garage and detached garage with power. F. At least one receptacle outlet that is accessible while standing at grade level and located not more than6-feet, 6 -inches (1981 -mm) above grade, shall be installed outdoors at the front and back of each dwelling unit having direct access to grade. Balconies, decks, and porches that are accessible from inside of the dwelling unit and that have a usable area of 20 square feet. F. Attics or crawlspaces containing equipment must be provided with at least one receptacle outlet within25-feet of the equipment. G. Hallways 10 -feet or more in length. 48 Two 20 -amp rated branch circuits shall serve receptacles in the kitchen, pantry, breakfast area, and dining area. At least one 20 -amp branch circuit shall supply bathroom receptacles and at least one 20 -amp branch circuit shall supply laundry. (IRC E3703.2, E3703.3, E3901) 50 Ground fault protection shall be provided on all 125 -volt, single phase, 15 and 20 -amp receptacles in the following locations: bathrooms, garages, unfinished grade level accessory buildings, at exterior locations, crawlspaces, unfinished basements, kitchen counters, within 6ft. of laundry, utility and wet bar sinks, boathouses, hydro massage, spa and hot tub locations. Receptacles must be in a readily accessible location. (IRCE3902, E3902.11) 51 Combination type Arc -Fault circuit interrupters must be installed on all 120 -volt 15 and 20 -amp branch circuit outlets in Receptacle outlets are required in every family room, dining room, living room, parlor, library, den, sunroom, bedroom, recreation room, hallway, closets, and similar dwelling areas. (IRC 3902.12) 52 At least one wall switch -controlled lighting outlet shall be installed in every habitable room, bathroom, hallway, (10ft) stairway, attached garage, detached garage with electric power, and at the exterior side of each outdoor egress door having grade level access. Attics, under floor spaces, utility rooms and basements containing equipment or used for storage must be provided with a switch 53 Smoke alarms shall comply with UL 217. Smoke alarms are to be powered by the building's wiring operated light. (IRC E3903)with battery backup and shall be interconnected so the actuation of one alarm will activate all alarms in the dwelling unit. Smoke alarms shall be installed in the following locations: (IRC R314) A. In each sleeping room; B Outside each sleeping area in the immediate vicinity of the bedrooms; and C. ach additional story including basements. city of 54 Carbon Monoxide alarms are required in a single-family dwelling that has fuel -fired appance(.Slt, giv;pe fireplace, or an attached garage. The alarm must be installed within 15 -feet of the entrance 'ddbh sleeping room. Must be listed by a nationally recognized, independent lab. Plugs into a dwelling's electric l cutlet and has a battery backup. They may be combined with a smoke -detecting device if the combined device complies with applicable law. (IRC R315) 55 Clothes closet lighting shall be limited to surface -mounted or recessed incandescent fixtures with completely enclosed lamps, and surface -mounted or recessed fluorescent fixtures.Surface mounted fixtures shall be installed on the wall above the door or on the ceiling with the following clearances between the fixture and the nearest point of a storage space: (IRC E4003.12)A. Incandescent fixtures or LED shall have a minimum 12 -inch clearance. B. Fluorescent fixtures shall have minimum 6 -inch clearance. Recessed fixtures shall be installed in the wall or ceiling with the following clearances: A Recessed incandescent fixtures shall have a minimum 6 -inch clearance to the nearest point of storage. B. Recessed fluorescent fixtures shall have a minimum 6 -inch clearance to the nearest point of storage. 56 Working space must be provided around energized equipment for servicing and maintenance. The minimum dimensions shall not be less than 36 -inches in depth and 30 -inches in width in front of the equipment. Working space shall extend to at least 6 -feet, 6 -inches above the floor. (IRC E3405.2) 57 Electrical fixtures installed in wet or damp locations shall be installed so that water cannot enter or accumulate n wiring compartments or other electrical parts. Fixtures installed in wet locations must be labeled "suitable for wet locations". Fixtures installed in damp locations must be labeled "suitable for damp locations" or "suitable for wet locations". Switches or circuit breakers located in wet locations or outdoors must be enclosed in a weatherproof enclosure. Outdoor receptacles must have a weatherproof enclosure and an in -use cover. Cord -connected fixtures, hanging fixtures, track lighting, pendants, and ceiling fans shall not be located within3-feet horizontally and 8 -feet vertically from the top of a tub or shower rim. (IRC E4003.9, E4002.8, E4002.9,(E4002.10, E4003.9, E4003.10,E4003.11) Plumbing Requirements 58 DWV systems shall be tested on compellation of the rough piping installation by water or for piping system other than plastic by air with no evidence of leakage. Either test shall be applied to the drainage system in its entirety or in sections after rough piping has been installed .1) Water test 10 feet above the highest fitting connection or to the highest point of the completed system. The system shall prove leak free for 15 minutes. 2) Air test shall maintain 5lbs of pressure for 15 minutes. 59 Piping must be inspected and tested prior to concealing. It shall be protected against physical damage and it must be approved for use and bear the identification of the manufacturer. (IRC P2503, P2603, P2608.1) 60 Bathtubs, walls above bathtubs with shower heads, shower floors, and shower compartments shall be finished with a non-absorbent surface which extends to a height not less than 6' above the floor. Showers must have a minimum 900 square inches of interior area and a minimum dimension in each direction of 30 -inches. Shower valves must be pressure balance/thermostatic mixing valves. Shower receptors shall have a curb threshold not less than 1 -inch below the sides and back of the receptor. The curb shall measure a mi . of 2 -inches to a maximum of 9 -inches above the top of the drain. (IRC R307, P2708, P2709) 61 The centerline of toilets or bidets shall not be less than 15 -inches from adjacent walls or t . .tt6fttis'bidets, and lavatories must have a minimum clear space of 21 -inches in front of the fixture. Lavatories, equire a 4 -inch clearance to wall or to a toilet. (IRC P2705) 62 Showers and tub/shower combinations shall have control valves of the pressure balance, thermostatic mixing or combination pressure balance/thermostatic mixing valve types with high limit stop per ASSE 1016 or CSAB125.1. Tubs shall also have a control valve as listed for a shower or a water -temperature -limiting device that conforms to ASSE 1070. The high limit stop for a device shall be set to a maximum of 120`. (IRC P2708.3,P2713.3) 63 Shower doors shall have safety glazing; hinged show door shall open outward. (R308.4.5, P2708.1) 64 Backflow prevention must be provided to prevent contamination of potable water. This includes but is not limited to: hose connections, irrigation systems, boilers, solar systems, fire sprinklers, and dishwashers. Backflow device must be inspected and approved by a 3rd party agency. (IRCP2902.2, Table P2902.3, P2717) Insulation 65 R-20 Walls R-49 Ceiling R-19 Crawlspace Window U -Factor .32 Floor R-30 66 Supply Ducts in attics shall be insulated to a minimum of R-8. All other ducts shall be insulated to minimum R-6. ( N 1103.2. 1) 67 Combustible insulation shall be separated a minimum of 3 -inches from fan motors and heat -producing devices. Insulation shields must be provided where vents pass thorough insulated assemblies and must terminate at least 2 -inches above attic insulation materials. Can lights must be airtight if located in the building envelope. (G2426.4) Class I or II vapor retarders are required on the interior side of the insulation in framed walls, floors and roof/ceilings of the building's thermal envelope. The vapor barrier is not required in construction where moisture or freezing will not damage the materials, or where the framed cavity (or space) is ventilated to allow moisture to escape. A vapor retarder is not recommended on a concrete basement foundation wall or in a shower /bath compartment (IRC 702.7, R702.7.1). Wallboard Requirements 68 The garage shall be separated from the residence and its attic by materials of not less than %-inch gypsum board applied to the garage side. Garages beneath habitable rooms shall be separated from all habitable rooms above by not less than 5 8 -inch Type X gypsum board. Where the separation is a floor -ceiling assembly, the structure supporting the separation shall also be protected by not less than %-inch gypsum board. (IRC R302.6) Openings between the garage and residence shall be equipped with solid wood doors not less than 1 -inch in thickness, solid or honeycomb core steel doors not less than 1 -inch thick, or 20 -minute fire -rated doors. Openings are prohibited between garages and rooms used for sleeping. (11302.5.1 )Doors betwee 8V_ache� garages and living space shall be weather stripped to the degree necessary to make them airti "t and'sha ll be F self-closing and self -latching. Wheat Ridge Divisor. 69 Enclosed accessible space under stairs shall have walls, under stair surface and any soffits protected on the enclosed side with %-inch gypsum board (IRC R302.7). 70 Cement, fiber -cement, glass mat gypsum backer and fiber reinforced gypsum in compliance with ASTM C 1288, C 1325, Cl 178, or Cl 178 and installed in accordance with manufacturer recommendations shall be used as backers for wall tile in tub and shower areas and wall panels in shower areas. (IRC R702.4.2) 71 Nail spacing for gypsum board % gypum board Ceiling 16oc, 7", nails 12", Type S screws 1/2 wall spacing 24"OC, 8" nail spacing. 12"OCscrews. 5/8 ceiling board 16"OC, 7"nails I 2"spacing, screws 24OC 8". 72. Water-resistant gypsum backing board used as the base or backer for adhesive application of ceramic tile or other required nonabsorbent finish material shall conform to ASTM C1396, C1178 or C1278. It is permitted on ceilings where framing spacing does not exceed 12 -inches o.c. for %-inch thick or 16 -inches o.c. for 5 8 -inch thick gypsum board. Water-resistant gypsum board shall not be installed over a vapor retarder in a shower or tub compartment and may not be used where there will be direct exposure to water, or in areas of continuous high humidity. All cut and exposed edges shall be sealed. (IRC R702.3.8) 73 Floor assemblies, not required elsewhere in this code to be fire resistance rated, shall be provided with a inch gypsum wall board membrane, 5/8 inch wood structural panel membrane, or equivalent on the underside of the floor framing member.(IRC 501.3) Final Inspection Requirements 74 Buildings shall have approved address numbers, building numbers or approved building identification placed in a position that is plainly legible and visible from the street or road fronting the property. (IRC 319) 75 All dwellings shall have a controlled method of water dispersal from roofs that will collect and discharge all roof drainage at least 5 -feet from the foundation. Gutters, downspouts, downspout extensions shall be deemed adequate to meet these requirements. Surface drainage shall be diverted to a storm sewer conveyance or other approved point of collection so as to not create a hazard. Lots shall be graded so as to drain surface water away from foundation walls. The grade away from foundation walls shall fall a minimum of 6 -inches within the first 10 -feet. (IRC R401.3 and R801.3) Swimming pools, fountains, hot tubs, spas, and hydro -massage "Jacuzzi" tubs and similar installations shall comply with all provisions of the IRC for the approval of bonding equipment and lighting. All 15 and 20 amp, single-phase 125 -volt receptacles located within 20 -feet of the inside walls of pools, outdoor spas and hot tubs shall be protected by a GFCI. Motors and equipment must be accessible without damaging the building structure or building finish. (IRC E4202, E4203, EE4204, E4205, E4206) The reinforcing shell of the pool shell, metal forming shells, coping stones, deck, brackets of niche fixtures, metal fittings, and electrical equipment, located less than 5 -feet horizontally and less than 12 -feet above maximum water level of swimming pools and built in place hot tubs shall be bonded together. Th .'parts City of specified above shall be connected to an equipotential bonding grid. (IRC E4204.2) (VWVheat Ridge 7500 W. 29T" Ave i Wheat Ridge, Co 80033-8001 ildins Divis;,t 303-235-2878 �� • W If cheat col►wumm oEvewrMr� �� APPROVED Reviewed for Code Compliance —" I -2--3-0-a Plans i ,finer Date Vdidiw at aermR- Thr .sooner of u permit w approval o/ plans specifiralions and eomputol,ons s hail not be a perout far, or on approval of, any violation to any of the provisions of the building code or of any Cay ordinances. Perms DreM" to give authority to violofe of cancel the provisions of the SuddxV codes Or~ ordinonces of the City shay not be valid. (a NLACA cski C- kSc L. ��_� ��,�� Cc, L \ v 11\1 � Z -w, v.,%, C— A A ►MAS-r�2 i���vw.. �q�--j� S r Nc w r. 1 l/AKITy 54\1.:�Ii vi►-.,Iy cLc00%^ ` Sv ni 2c,c, V,.\, rJEW -,.,Y N:•W YM( IT 0;; 0 00 0 a AIfW VAN tT`J a = i�►2cc w- D-mz-w C -A,& 1 E? '0 0 - - - --234" -- _84"- _ 82" 6811 Zack Magalei Kitchen Revision 2 Joseph Klein Cabinetry 0 CO Door Style: S8 -White Maple Finish: White Maple _ Top Molding: SM8 No Light Rail 96„ W243 W2430 V\/2430 W2430 O 09- DB36-3 0 0 O BWBK15' 1 r- -55" DB21-3 DISHW24 W2130 -R W2430 SB36 Ell 5-L W3612 W2730 - --135"— N N v a 00 r- o r.. 0! W 00 Q c„ i'0 0 J w 3 0) I accept all of these dimensions and any changes will need to be adjusted onsite or additional cabinetry will need to be purchased. Signature: Date: All dimensions and size designations given are subject to verification on the job site, and adjustment to job conditions. This is an original design and must not be released or copied unless applicable fee has been paid or job order placed. Design 2017 Print :7'20 (Wheat Ridge Building Divison BathandGranite-Zach Magalei Kitchen Revision 2 1 All 1 Drawing #: 1 I No Scale. `3026 MaS!-S�, IN PECTION RECORD INSPECTION REQUEST LINE: (303) 234-5933 Occupancy/Type Inspections will not be performed unless this card is posted on the project site. Call the inspection request line before 11:59 p.m. to receive an inspection the following business day.** Inspector Must Sign ALL Spaces pertinent to this project Foundation Inspections Date Inspector Initials Comments Pier Plumbing Concrete Encased Ground (CEG) Foundation / P.E. Letter Do Not Pour Concrete Prior To Approval Of The Above Inspections Underground/Slab Inspections Date Inspector Initials Comments Electrical Wall Sheathing Sewer Service Mid -Roof Plumbing Do Not Cover Underground or Below/In-Slab Work Prior To Approval Of The Above Inspections Rough Inspections Date Inspector Initials Comments Wall Sheathing Mid -Roof Lath / Wall Tie Rough Electric " Rough Plumbing/Gas Line Rough Mechanical Rough Framing Rough Grading Insulation Drywall Screw/ Nail Final Inspections Date Inspector Initials Comments Landscaping & Parking / Planning Dept. Inspections from these entities should be requested one week in advance. For landscaping and parking inspections call 303-235-2846. For ROW and drainage inspections call 303-235-2861. For fire inspections contact the Fire Protection District for your project. ROW & Drainage / Public Works Dept. Floodplain Inspection (if applicable) Fire Inspection / Fire Protection Dist. Final Electrical Final Plumbing Final Mechanical Roof 3 / Final Window/Doors Final Building NOTE: All items must be completed and approved by Planning, Public Works, Fire and Building before a Certificate of Occupancy is issued. Approval of the Final Building inspection does not constitute authorization of occupancy. *For low voltage permits — Please be sure that rough inspections are completed from the Fire District and electrical low voltage by the Building Division. "For Inspection Time Window — Please email insptimerequest@ci.wheatridge.co.us by 8:00 A.M. the morning of the inspection with the property address in the subject line of the email. Time window is based on the inspector's route. Occupancy Is Not permitted Until A Certificate of Occupancy Is Issued Protect This Card From The Weather i CITY OF WHEAT RIDGE Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: R t Job Address: -3 C ( 1, �-, Permit Number: ­)� Q) 7 t lb Q,-./ __� ❑ No one available for inspection: Time""I"AM/PM Re -Inspection required: Yes No * When corrections have been made, call for re -inspection at 303-234-5933 ZDate: " / g % Inspector: - DO NOT REMOVE THIS NOTICE CITY OF WHEAT RIDGE ]�;Ir/� Building Inspection Division (303) 234-5933 Inspection line '(303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: Job Address: Permit Number: i3 1 i it 0 V bt jo ❑ No one available for inspection: Time `7 ' /6, AM/PM Re -Inspection required: Yes No * When corrections have been made, call for re-inspectio0'at 303-234-5933 Date: Inspector: .`�l �` DO NOT REMOVE THIS NOTICE City of Wheat Ridge Residential Roofing PERMIT - 201700443 PERMIT NO: 201700443 ISSUED: 04/03/2017 JOB ADDRESS: 3625 Chase ST EXPIRES: 04/03/2018 JOB DESCRIPTION: 20 squares of low slope EPDM with 1/2 inch fiber board fullly adhered; 40 sq of 30 year dimensional shingles, 40 sheet of new plywood replacement and lay over the existing 1x6 boards *** CONTACTS *** OWNER (303)913-5828 MAGALEI MELODY S SUB (303)582-4252 Julio Blanco/Eduardo Vasquez 160145 Highline Roofing & Gutters Inc *** PARCEL INFO *** ZONE CODE: UA / Unassigned USE: UA / Unassigned SUBDIVISION CODE: 2412 / LAKESIDE, STEWART GARDENS, OLI BLOCK/LOT#: 0 / *** FEE SUMMARY *** ESTIMATED PROJECT VALUATION: 24,000.00 FEES Total Valuation 0.00 Use Tax 432.00 Permit Fee 426.20 ** TOTAL ** 858.20 ____ *** COMMENTS *** *** CONDITIONS *** Effective December 1, 2014, asphalt shingle installations require an approved midroof inspection, conducted when 25-75 percent of the roof covering is installed, prior to final approval. Installation of roof sheathing (new or overlay) requires an approved inspection prior to installation of ANY roof coverings and is require on the entire roof when spaced or board sheathing with ANY gap exceeding A/2 -inch exists. Asphalt shingles are required to be fastened to the roof deck with a minimum of 6 nails per shingle. Ice and water shield is required. Eave and rake metal is required. A ladder extending 3 feet above the roof eave and secured in place is required to be provided for all roof inspections. Roof ventilation is required to comply with applicable codes and/or manufacturerae"s installation instructions, whichever is more stringent. In order to pass a final inspection of elastomeric or similar type roof coverings, a letter of inspection and approval from the manufacturer&#39;s technical representative stating that "the application of the roof at (project address) has been applied in accordance with the installation instruction for (roof material brand name) roof covering" is required to be on site at the time of final inspection. A City of Wheat Ridge „14 el Residential Roofing PERMIT - 201700443 PERMIT NO: 201700443 ISSUED: 04/03/2017 JOB ADDRESS: 3625 Chase ST EXPIRES: 04/03/2018 JOB DESCRIPTION; 20 squares of low slope EPDM with 1/2 inch fiber board fullly adhered; 40 sq of 30 year dimensional shingles, 40 sheet of new plywood replacement and lay over the existing 1x6 boards I, by m>' signature, do hereby attest that the work to be performed shall comply with all accompanying approved plans and specifications, applicable building codes, and all applicable municipal codes, policies and procedures, and that 1 am the legal owner or have been authorized by the legal owner of the property and am authorized to obtain this permit and perform the work described and approved in conjunction with this permit. I further attest that I am legally authorized to include all entities named within this document as parties to the work to be performed and that all work to bip performed is disclosed in this document and/or its' accompanying approved plans and specifications. Signature of OWNER or CONTRACTOR (Circle one) Date I . This permit was issued based on the information provided in the permit application and accompanyingplans and specifications and is subject to the compliance with those documents, and all applicable statutes, ordinances, regulations, policies and procedures. 2. This permit shall expire 365 days after the date of issuance regardless of activity. Requests for extension must be made in writing and received prior to the date of expiration. An extension of no more than 180 days made be granted at the discretion of the Chief Building Official and may be subject to a fee equal to one-half of the original permit fee. 3, If this permit expires, a new permit may be required to be obtained. Issuance of a new permit shall be subject to the standard requirements, fees and procedures for approval of any new permit. Re -issuance or extension of expired permits is at the sole discretion of the Chief Budding Official and is not guaranteed. 4. No work of any manner shall be performed that shall results in a change of the natural flow of water without prior and specific approval. 5. The permit holder shall notify the Building and Inspection Services Division in accordance with established policy of all required inspections and shall not proceed or conceal work without written approval of such work from the Building and Inspection Services Division. The issuance or granting of a permit shall not be construed to be a permit for, or an approval of, any violation of any provision of any applicabIrMINIor any ordinance or regulation of this jurisdiction. Approval of work is subject to field inspection. A6UWK__r"A4 Signature of Chief Building Official Date REQUESTS MUST BE MADE BY 11:59PM ANY BUSINESS DAY FOR INSPECTION THE FOLLOWING BUSINESS DAY. Inspection time requests will be accepted by email only. Please email requests to insptimerequest@ci.wheatridge.co.us between 7:30am and 8:00am, the morning of the inspection. Please put the address of the inspection in the subject line. City of -21 �Whcat_j" 9e COMMUNITY DEVELOPMENT Building & Inspection Services Division 7500 W. 291h Ave., Wheat Ridge, CO 80033 Office: 303-235-2855 * Fax: 303-237-8929 Inspection Line: 303-234-5933 Email: perm its(a)ci.wheatridge.co.us I FOR OFFICE USE ONLY I Date: �/ 3//� r Plan/Permit # i "I k --N G�v I Lit � Plan Review Fee: Building Permit Application *** Please complete all highlighted areas on both sides of this form. Incomplete applications may not be processed. *** Property Address: -> S� N� S S7— Property lProperty Owner (please print): 2�qLJ 6 ,l /� G ,¢ /_ I L Phone: ,363 Property Owner Email: Mailing Address: (if different than property address) Address:�- (� ���L�� II,�J S 7' City, State, Zip: �,� i It E A T 1�>ll C Ld Architect/Engineer: Architect/Engineer E-mail: Phone: Contractor:IG�N�J�� Contractors City License #: 1 a i S Phone: 220 -;) ,;2 y Contractor E-mail Address: Ifr h pool- e3 (oi-t . Sub Contractors: Electrical: W.R. City License # Other City Licensed Sub: City License # Plumbing: W.R. City License # Other City Licensed Sub: City License # Mechanical: W.R. City License # Complete all information on BOTH sides of this form ❑ COMMERCIAL � RESIDENTIAL Description of work: (Check all that apply) ❑ NEW COMMERCIAL STRUCTURE ❑ ELECTRICAL SERVICE UPGRADE ❑ NEW RESIDENTIAL STRUCTURE ❑ COMMERCIAL ROOFING ❑ COMMERCIAL ADDITION RESIDENTIAL ROOFING ❑ RESDENTIAL ADDITION ❑ WINDOW REPLACEMENT ❑ COMMERCIAL ACCESSORY STRUCTURE (Garage, shed, deck, etc.) ❑ RESIDENTIAL ACCESSORY STRUCTURE (Garage, shed, deck, etc.) ❑ MECHANICAL SYSTEM/APPLIANCE REPAIR or REPLACEMENT ❑ PLUMBING SYSTEM/APPLIANCE REPAIR or REPLACMENT ❑ ELECTRICAL SYSTEM/APPLIANCE REPAIR or REPLACEMENT ❑ OTHER (Describe) (For ALL projects, please provide a detailed description of work to be performed, including current use of areas, proposed uses, square footage, existing condition and proposed new condition, appliance size and efficiency, type and amount of materials to be used, etc.) %iGlfe /It 6 /% —9 — W )F ti&a) P1 -y wooer ,�C6�L�tc���i /j,k�✓� .L/4c3 77tLO Sq. FULF Amps �X tsTi<0h !xG . , 6A-nas Btu's Gallons Squares Other Project Value: (Contract value or the cost of all materials and labor included in the entire project) $ J7 , 6d6 OWNER/CONTRACTOR SIGNATURE OF UNDERSTANDING AND AGREEMENT I hereby certify that the setback distances proposed by this permit application are accurate and do not violate applicable ordinances, rules or regulations of the City of Wheat Ridge or covenants, easements or restrictions of record; that all measurements shown and allegations made are accurate; that I have read and agree to abide by all conditions printed on this application and that I assume full responsibility for compliance with applicable City of Wheat Ridge codes and ordinances for work under any permit issued based on this application; that I am the legal owner or have been authorized by the legal owner of the property to perform the described work and am also authorized by the legal owner of any entity included on this application to list that entity on this application. I, the applicant for this building permit application, warrant the truthfulness of the information provided on the application. CIRCLE ONE: (OWNER) (CONTRACTOR) or (AUTHORIZED REPRESENTATIVE) of (OWNER) (CONTRACTOR) Electronic Signature (first and last name): C, /%A2I71�� -20t)c62 DATE: tJ / 2 ZONING COMMMENTS: Reviewer: BUILDING DEPARTMENT COMMENTS: Reviewer: DEPARTMENT USE ONLY OCCUPANCY CLASSIFICATION: Building Division Valuation: $ DRIVER LICENSE 1 VASOUE2-MIRM'DA ­- 2 EDUARDO ' 8 1048 LAREDO ST v AURORA, CO 80011 n 3 DOS 4a Iss 11a Endorsements 12/6^d1978 12!0612016 " 4d Customer Identillet 4b Exp 12 Restrictions 1 94-333-1112 12/041021 NONE 3 DD Previous Type 8 Vehide Classftieabons 16346138126 A R 15 Sex 16 H¢ M S'-a` 48 Eyes 17 Wgt , BRO 2061b -- Ismail BLK �2MrMnon £...... 9.=ar.+P 1100 City of Wheat Ridge Residential Roofing PERMIT - 201700443 PERMIT NO: 201700443 ISSUED: 04/03/2017 JOB ADDRESS: 3625 Chase ST EXPIRES: 04/03/2018 JOB DESCRIPTION: 20 squares of low slope EPDM with 1/2 inch fiber board fullly adhered; 40 sq of 30 year dimensional shingles, 40 sheet of new plywood replacement and lay over the existing 1x6 boards *** CONTACTS *** OWNER (303)913-5828 MAGALEI MELODY S SUB (303)582-4252 Julio Blanco/Eduardo Vasquez 160145 Highline Roofing & Gutters Inc *** PARCEL INFO *** ZONE CODE: UA / Unassigned USE: UA / Unassigned SUBDIVISION CODE: 2412 / LAKESIDE, STEWART GARDENS, OLI BLOCK/LOT#: 0 / *** FEE SUMMARY *** ESTIMATED PROJECT VALUATION: 24,000.00 FEES Total Valuation 0.00 Use Tax 432.00 Permit Fee 426.20 ** TOTAL ** 858.20 ____ *** COMMENTS *** *** CONDITIONS *** Effective December 1, 2014, asphalt shingle installations require an approved midroof inspection, conducted when 25-75 percent of the roof covering is installed, prior to final approval. Installation of roof sheathing (new or overlay) requires an approved inspection prior to installation of ANY roof coverings and is require on the entire roof when spaced or board sheathing with ANY gap exceeding A/2 -inch exists. Asphalt shingles are required to be fastened to the roof deck with a minimum of 6 nails per shingle. Ice and water shield is required. Eave and rake metal is required. A ladder extending 3 feet above the roof eave and secured in place is required to be provided for all roof inspections. Roof ventilation is required to comply with applicable codes and/or manufacturerae"s installation instructions, whichever is more stringent. In order to pass a final inspection of elastomeric or similar type roof coverings, a letter of inspection and approval from the manufacturer&#39;s technical representative stating that "the application of the roof at (project address) has been applied in accordance with the installation instruction for (roof material brand name) roof covering" is required to be on site at the time of final inspection. A City of Wheat Ridge „14 el Residential Roofing PERMIT - 201700443 PERMIT NO: 201700443 ISSUED: 04/03/2017 JOB ADDRESS: 3625 Chase ST EXPIRES: 04/03/2018 JOB DESCRIPTION; 20 squares of low slope EPDM with 1/2 inch fiber board fullly adhered; 40 sq of 30 year dimensional shingles, 40 sheet of new plywood replacement and lay over the existing 1x6 boards I, by m>' signature, do hereby attest that the work to be performed shall comply with all accompanying approved plans and specifications, applicable building codes, and all applicable municipal codes, policies and procedures, and that 1 am the legal owner or have been authorized by the legal owner of the property and am authorized to obtain this permit and perform the work described and approved in conjunction with this permit. I further attest that I am legally authorized to include all entities named within this document as parties to the work to be performed and that all work to bip performed is disclosed in this document and/or its' accompanying approved plans and specifications. Signature of OWNER or CONTRACTOR (Circle one) Date I . This permit was issued based on the information provided in the permit application and accompanyingplans and specifications and is subject to the compliance with those documents, and all applicable statutes, ordinances, regulations, policies and procedures. 2. This permit shall expire 365 days after the date of issuance regardless of activity. Requests for extension must be made in writing and received prior to the date of expiration. An extension of no more than 180 days made be granted at the discretion of the Chief Building Official and may be subject to a fee equal to one-half of the original permit fee. 3, If this permit expires, a new permit may be required to be obtained. Issuance of a new permit shall be subject to the standard requirements, fees and procedures for approval of any new permit. Re -issuance or extension of expired permits is at the sole discretion of the Chief Budding Official and is not guaranteed. 4. No work of any manner shall be performed that shall results in a change of the natural flow of water without prior and specific approval. 5. The permit holder shall notify the Building and Inspection Services Division in accordance with established policy of all required inspections and shall not proceed or conceal work without written approval of such work from the Building and Inspection Services Division. The issuance or granting of a permit shall not be construed to be a permit for, or an approval of, any violation of any provision of any applicabIrMINIor any ordinance or regulation of this jurisdiction. Approval of work is subject to field inspection. A6UWK__r"A4 Signature of Chief Building Official Date REQUESTS MUST BE MADE BY 11:59PM ANY BUSINESS DAY FOR INSPECTION THE FOLLOWING BUSINESS DAY. Inspection time requests will be accepted by email only. Please email requests to insptimerequest@ci.wheatridge.co.us between 7:30am and 8:00am, the morning of the inspection. Please put the address of the inspection in the subject line. City of -21 �Whcat_j" 9e COMMUNITY DEVELOPMENT Building & Inspection Services Division 7500 W. 291h Ave., Wheat Ridge, CO 80033 Office: 303-235-2855 * Fax: 303-237-8929 Inspection Line: 303-234-5933 Email: perm its(a)ci.wheatridge.co.us I FOR OFFICE USE ONLY I Date: �/ 3//� r Plan/Permit # i "I k --N G�v I Lit � Plan Review Fee: Building Permit Application *** Please complete all highlighted areas on both sides of this form. Incomplete applications may not be processed. *** Property Address: -> S� N� S S7— Property lProperty Owner (please print): 2�qLJ 6 ,l /� G ,¢ /_ I L Phone: ,363 Property Owner Email: Mailing Address: (if different than property address) Address:�- (� ���L�� II,�J S 7' City, State, Zip: �,� i It E A T 1�>ll C Ld Architect/Engineer: Architect/Engineer E-mail: Phone: Contractor:IG�N�J�� Contractors City License #: 1 a i S Phone: 220 -;) ,;2 y Contractor E-mail Address: Ifr h pool- e3 (oi-t . Sub Contractors: Electrical: W.R. City License # Other City Licensed Sub: City License # Plumbing: W.R. City License # Other City Licensed Sub: City License # Mechanical: W.R. City License # Complete all information on BOTH sides of this form ❑ COMMERCIAL � RESIDENTIAL Description of work: (Check all that apply) ❑ NEW COMMERCIAL STRUCTURE ❑ ELECTRICAL SERVICE UPGRADE ❑ NEW RESIDENTIAL STRUCTURE ❑ COMMERCIAL ROOFING ❑ COMMERCIAL ADDITION RESIDENTIAL ROOFING ❑ RESDENTIAL ADDITION ❑ WINDOW REPLACEMENT ❑ COMMERCIAL ACCESSORY STRUCTURE (Garage, shed, deck, etc.) ❑ RESIDENTIAL ACCESSORY STRUCTURE (Garage, shed, deck, etc.) ❑ MECHANICAL SYSTEM/APPLIANCE REPAIR or REPLACEMENT ❑ PLUMBING SYSTEM/APPLIANCE REPAIR or REPLACMENT ❑ ELECTRICAL SYSTEM/APPLIANCE REPAIR or REPLACEMENT ❑ OTHER (Describe) (For ALL projects, please provide a detailed description of work to be performed, including current use of areas, proposed uses, square footage, existing condition and proposed new condition, appliance size and efficiency, type and amount of materials to be used, etc.) %iGlfe /It 6 /% —9 — W )F ti&a) P1 -y wooer ,�C6�L�tc���i /j,k�✓� .L/4c3 77tLO Sq. FULF Amps �X tsTi<0h !xG . , 6A-nas Btu's Gallons Squares Other Project Value: (Contract value or the cost of all materials and labor included in the entire project) $ J7 , 6d6 OWNER/CONTRACTOR SIGNATURE OF UNDERSTANDING AND AGREEMENT I hereby certify that the setback distances proposed by this permit application are accurate and do not violate applicable ordinances, rules or regulations of the City of Wheat Ridge or covenants, easements or restrictions of record; that all measurements shown and allegations made are accurate; that I have read and agree to abide by all conditions printed on this application and that I assume full responsibility for compliance with applicable City of Wheat Ridge codes and ordinances for work under any permit issued based on this application; that I am the legal owner or have been authorized by the legal owner of the property to perform the described work and am also authorized by the legal owner of any entity included on this application to list that entity on this application. I, the applicant for this building permit application, warrant the truthfulness of the information provided on the application. CIRCLE ONE: (OWNER) (CONTRACTOR) or (AUTHORIZED REPRESENTATIVE) of (OWNER) (CONTRACTOR) Electronic Signature (first and last name): C, /%A2I71�� -20t)c62 DATE: tJ / 2 ZONING COMMMENTS: Reviewer: BUILDING DEPARTMENT COMMENTS: Reviewer: DEPARTMENT USE ONLY OCCUPANCY CLASSIFICATION: Building Division Valuation: $ DRIVER LICENSE 1 VASOUE2-MIRM'DA ­- 2 EDUARDO ' 8 1048 LAREDO ST v AURORA, CO 80011 n 3 DOS 4a Iss 11a Endorsements 12/6^d1978 12!0612016 " 4d Customer Identillet 4b Exp 12 Restrictions 1 94-333-1112 12/041021 NONE 3 DD Previous Type 8 Vehide Classftieabons 16346138126 A R 15 Sex 16 H¢ M S'-a` 48 Eyes 17 Wgt , BRO 2061b -- Ismail BLK �2MrMnon £...... 9.=ar.+P 1100 i 11 11 City of City of Wheat Ridge Municipal Building 7500 W. 29th Ave. Wheat Ridge, CO 0033-8001 P. 303.235.2846 F: 303.2352 57 December 12, 2016 TION NOTIFICATION is hereby given that the following address has been assigned to the property/properties as indicated below: CURRENT ' A -RESS.3625 Chase street NEW II E"SS. 3 x25 i se Str` t sn 3635 C hese Street n rte t SUBDIVISION:_ EC)T(s): ; Y: 2C 5 SECTION:- PARCEL NO: -19-25 1 _-00-02 NOTES. This is a courts not;flcatiora. Notification was previously sent on 9/24/2013 AUTHORIZEDS�. DATE: IST ION: 1, Property 01VIler 2. Jefferson County Assessor, : Data Control, Lacey Baler email to lig#,erL@`el `co.0 3. Jefferson CountyElections, A n H. Roth, 3500 Illinois St., Lararme Building, Suite 1100, Golden, CO 80401 4. Email to Jeffco IT (Mapping) Services at tc el fT o u d edel `tl ou . Jeffco Public Schools, : Communication S ices, 1829 Denver West Dr. Bldg, , 27, Golden, CO 80401 6. U.S. Post Office, , 3700 Tennyson St., Denver, CO 80212 7. Email to erlind `.piarth crus . goy dri .'.start _ field i tis �c�y and rlene:.vic revVitas s. ov and sarnantha.trt.sears ib s Hca 8. Xcel Energy, satidra.carden ss' celetier . oryt 9. Century Link, Capacity Provisioning Specialist, 5325 7.uni St., Room 728, Denver, CO 80221 107 C onicast Attn: Scott Moore, 6850 S. Tucson Way, Englewood, CO80112 11. `heat Ridge 'tater District 12. Wheat Ridge Saturation District 13. West Metro Eire District 14. Wheat Ridge Planning Division 15. Wheat, Ridge Building Division 16. Wheat Ridge Police Department 17, GIS Specialist 18. Log File NOTE: Please notify all ether parties concerned. ADDRESS MAP UPDATED B DATE: FOR OFFICE USE ONLY Date. City of L Wh6atidcre- Z-7-- COM'k'AUNITY [)EVELOPMENT PfanlPermit # Building & Inspection Services Division 2, r -:p i t, , v 7500 W. 2e Ave., Wheat Ridge, CO 80033 Plan Review Fee: Office: 303-235-2855 * Fax: 303-237-8929 Inspection Line: 303-234-5933 Building Permit Application 3625 Chase St. Wheat Ridge, CO 80212 Property Addre": Property Owner (please prino: Melody Magalei Phone: 303-913-582�j Address: Same as Above City, State, Zip: Arch ItecttEnaineer: N/A Contractor: Thd at Home Services, Inc Contractor E-mail Address: copermits@gmail.com r =� 1 N - owl IVA I'l 14KZ-4 # mgm, Plumbing: W.R, Cily License # Phone: . ......... .... - . ... . ...... - ... ...... ...... Complete all information on BOTH sides of this form 0 NEW COMMERCIAL STRUCTURE 0 ELECTRICAL SERVICE UPGRADE ENEW RESIDENTIAL STRUCTURE 0 COMMERCIAL ROOFING COMMERCIAL ADDITION RESIl "' ROOFING RESDENTIAL ADDITION Hl ih COMMERCIAL ACCESSORY STRUCTURE Wit,. shed, deck, RESIDENTIAL ACCESSORY STRUCTURE (Garage, shed, deck, etc.) MECHANICAL SYSTEM/APPLIANCE SYSTEM/APPLIANCE REPAIR iREPLACEMENT PLUMBING SYSTEM/APPLIANCE REPAIR or REPLACMENT ELECTRIrAfi • M i REPAIR 1 IM 1.R or REPLACEMENT amounto. be used, etc.11 U -value =.32 w Sq. RAF � Stu's ..� ,_� Gallons ,Amps � _ __._ Squares _ www_ m Other _ .�_ I ■ 19 I ■ U, C� F5 V9� ol Ci lziz Y z z z z z CL G. Z Z 40 co Z 44 Ic cz FA �v INSPECTION RECORD Occupanc /T.We INSPECTION REQUEST LINE: (303) 234-5933 Inspections will not be perfon-ned unless dais card is posted on the project site. Call the inspection request line before 11: 59 pm. to receive an inspection the following business day. Inspector Must Sign ALL Spaces pertinent to this project Foundation Inspections Date Inspector Comments Initials Monolithic Slab Reinforcement Caissons Concrete Encased Ground (CEG) Footing/Stemwall P.E. :L:etter Do Not Pour Concrete Prior To A roval Of The Above Ins ections Underground/Slab Inspections Date Inspector Comments Initials Electrical (Underground) Sewer Service (Underground) Water Service (Underground) Plumbing (Below I In-slab) Concrete A royal "nor �ln' ctor cre 0 s Date Initials als Heating (Below / In-slab) iso Not CoverUnder round oBelow/ r In-Slab Work Prior To royal Of The Above Ins ect ons Rough Inspections "o e'ow' Date Inspector Comments Initials Wall Sheathing Roof Sheathing Lath / Wall Tie Rough Electric Rough Plumbing Rough Mechanical Gas Piping Do Not Proceed Without A rovall Of Abovf Rough Framing �"ity of Wlhcmt R-nae Framing tio Insulation Drywall Screw / Nail Inspector f N41271 7 C41101T Final Inspections Date Initials 362-5 1.1ase ST Final Electrical Final Plumbing _J'T Final Mechanical 28,315 AOTH G !)U 512235 Roof 28.75 Final Building I Frame Landscaping Parking 6 Planning Dept. Inspections from these entities should be requestsc one week in advance. For landscaping and parking ROW & Drainage / Public Works Dept. inspections call 303-235-2846. For ROW and drainage inspections call 303-235-2861. For fire inspections Fire Inspection / Fire Protection Dist. contact the Fire Protection District for your project, "Note: All items must be completed and approved by Planning, Public Works, Fire and Building before a Certificate JcY.Jof Occupancy is issued. Approval of the Final Building inspection does not constitute authorization of occupancy. Occupancy Is Not Permitted Until A Certificate of Occupancy Is Issued Protect This Card From The Weather APR -22-2016 FRI 02'.34 PM [OSS ELECTRIC INC. FAX NO. 3037830508 E O! « »I © « « «,� <*<.<»atm ?;« ..........\ . . ~ » •� ©��\}�/ƒ% ^^� §¥##<� WR My Limm # 1400»$ 5711 C#aP ked -795-6116 +t$*2§2*x<6<«<w»! IN i • e • ♦ ♦; (p (p lease Property Owner Emaik Mailing dues, (if different than property address) Address, City, Mete, Zip: chil E in ` r E-mail: P ne Contractor: 64,wp itll f I. en tre, Complete all in on T sides of this for • • II prat of materiels to be :used, etc,) „k w # � S q. FULF Btu's Gallons Amps Square Other ♦��4 - r� City of Wheat Ridge Faxed Plumb. Permit PERMIT - 110477 PERMIT NO: 110477 ISSUED: 04/29/2011 JOB ADDRESS: 3625 CHASE ST EXPIRES: 04/28/2012 DESCRIPTION: Replace 40 gallon hot water heater * ** CONTACTS * ** owner 303/913 -5828 Melody Megalei sub 866/898 -0008 Mariana Kitchukova 08 -0021 Colorado Delta Mechanical Inc. ** PARCEL INFO ** ZONE CODE: UA USE: UA SUBDIVISION: UA BLOCK /LOT#k: 0/ ** FEE SUMMARY ** ESTIMATED PROJECT VALUATION: 850.00 FEES Permit Fee 40.00 Total Valuation .00 Use Tax 15.30 ** TOTAL ** 55.30 Conditions: Both front and back of permit need to be posted on job site. If one or the other is not present, INSPECTION WILL NOT BE PERFORMED. Work shall comply with 2006 IRC L 2005 NEC. Per IRC Sec. R313, smoke detectors are required to be installed in every sleeping room, in hallways outside of sleeping rooms, and on every level of the structure. Carbon Monoxide detectors are required to be installed within fifteen(15) feet outside the entrance to each sleeping room. Subject to field inspection. I, by my signature, do hereby attest that the work to be performed shall comply with all accompanying approved plans and specifications, applicable building codes, and all applicable municipal codes, policies and procedures, and that I am the legal owner or have been authorized by the legal owner of the property and am authorized to obtain this permit and perform the work described and approved in conjunction with this permit. I further attest that I am legally authorized to include all entities named within this document as parties to the work to be performed and that all work to be performed is disclosed in this document and /or its' accompanying approved plans and specifications. Signature of OWNER or CONTRACTOR (Circle one) Date 1. This permit was issued based on the information provided in the permit application and accompanying plans and specifications and is subject to the compliance with those documents, and all applicable statutes, ordinances, regulations, policies and procedures. 2. This permit shall expire 365 days after the date of issuance regardless of activity. Requests for extension must be made in writing and received prior to the date of expiration. An extension of no more than 180 days made be granted at the discretion of the Chief Building Official and may be subject to a fee equal to one- half of the original permit fee. 3. If this permit expires, a new permit may be required to be obtained. Issuance of a new permit shall be subject to the standard requirements, fees and procedures for approval of any new permit. Re- issuance or extension of expired permits is at the sole discretion of the Chief Building Official and is not guaranteed. 4. No work of any manner shall be performed that shall results in a change of the natural flow of water without prior and specific approval. 5. The permit holder shall notify the Building and Inspection Services Division in accordance with established policy of all required inspections and shall not proceed or conceal work without written approval of such work from the Building and Inspection Services Division. 6. The issuance or granting of a permit shall not be construed to be a permit for, or an approval of, any violation of any provision of any applicable code or any ordinance or regulation of this jurisdiction. Approval of work is subject to field ihspectwn. 7 Building Offical Date N EQUEST LINE: (303)234 -5933 BUILDING OFFICE: (303)235 -2855 MUST BE MADE BY 3PM ANY BUSINESS DAY FOR INSPECTION THE FOLLOWING BUSINESS DAY. INSPECTION RECORD Occupancy /Type INSPECTION LINE: (303) 234 -5933 Inspections will not be made unless this card is posted on the building site Call by 3:00 PM to receive inspection the following business day. 1. NSPECTOR MUST SIGN ALL SPACES PERTAINING TO THIS JOB F INSPE DATE INSPECTOR INITIALS COMMENTS: sons G) Concrete nd Monolithic SIGNED PRIOR TO PRO! CITY OF WHEAT RIDGE 04/29/11 2:36 PN edba Mariana Iichu.kov Weatherproof/ French Drain Rough Plumbing Sewer Service Lines Gas Piping Water Service Lines Rough Mechanical CONCRETE SLAB FLOOR Electrical (Underground) Plumbing (Underground) ROUGHS Sheathing Lath / Wall tie Mid -Roof Electrical Service SIGNED PRIOR TO PRO! CITY OF WHEAT RIDGE 04/29/11 2:36 PN edba Mariana Iichu.kov Rough Electric Rough Plumbing Gas Piping Rough Mechanical ABOVE INSPECTIONS TO BE Framing Insulation Drywall Screw �u_u4ir, nu. uvnwuuw nnuunl FINALS DPSP Replace 40 ilallon ho 55.30 1104,7 Electrical Permit Fee 40.00 Use Tax 15.30 Plumbing PAYME14T RECEIVED ANOUNT Mechanical V5 3376 55.30 Roof Auth Code: 092473 Building Final TOTAL 55.30 Fire Department R.O.W & Drainage WBESCALLEOD LANNING & ZONING, FIRE AND PUBLIC WORKS SHOULD Parking & Landscaping T ONE WEEK PRIOR TO FINAL INSPECTIONS. "/NOTE: ALL ITEMS MUST BE COMPLETED AND APPROVED BY PLANNING AND ZONING, BUILDING AND PUBLIC WORKS BEFORE A CERTIFICATE OF OCCUPANCY IS ISSUED. FINAL INSPECTION BY THE BUILDING DIVISION DOES NOT CONSTITUTE AUTHORIZATION OFA CERTIFICATE OF OCCUPANCY NOR PERMISSION FOR OCCUPANCY. OCCUPANCY NOT PERMITTED UNTIL CERTIFICATE OF OCCUPANCY IS ISSUED PROTECT THIS CARD FROM THE WEATHER 0629/2011 PRI 1513 FAX 303 37 8929 303 Beet Nay ®001 /001 ` .........:... .............. ....-- ---- ..:.1,. ........-.............,.,.....'..,......--. ...,....:.,..------ --- -........ ---° --.._....:..,.,._:, ......... .._ ........,. .......,.:- ........-- �.u...:... ... ♦ Clty of 0.X Plor 0 Mullding 6lnspecdon Servlaos D►yl8lon , OS 7500 W 29 AV®., Wh tAlsi�.a 3' u ly�� 7�' arnnle0 0� =j� ofAoe: 303 - 236.2866 F9Xt 303-237.8829 r Inepectlon Line: 303 -2� -.,833 -- Building Permit Apppoetton _ Propa,tyAddnme: 1 a5 (si1aiSe.) m Property Owner (pleeeepflno: t UD pharm. c1VJ -"II�. HlelllnQ Address: (ffdht erent than propeAy Wdpnl ee) A ddress: 3 UA/ A f A QVI dot 1 �WfIA L 4 W 6Ud �a4 Clay, state, Zip; 010 Lloenee # City LigeM0 # Clty License # Ro*w see "at ems of submmegl OWNMCONTRACTOR NONATTIRS OR t1ND8RBTANDING AND AaARRMBNT t horoby wnity that {ha entheok dlstntoa ptbposed by dde pamlt applloaUOtl sro neeiaare and donor vlotate ttpptlarbts txdinenxs, tole, orrmtllatlone of the City of whet Aldgo or oovemmah aaumtinta orm Metlom of»cmd; that all mauurommu sbo m and 411apdon, m,de era sceuuhl That I have rud authori and r to gblda by all conditlons printed m this &WIatlon and that I euutaa tbli rapotulblllryty for compliance with epplltctble Chy of what RW`e codes glid otdlnetlau &rwmltundef any porch IYYtted band an thl, eppll wNon; that r gat pat laysi owner orfiw Man aothol zcd by the t ottw gtthe and tan also zod b the to O " pp " 1 0 rho deeerlbed wade Y get wnprafany anliry Included ( $fi t \ hte.appttaatto / n�to t4.t thata,dty on dlla appllatton. MICUONS AMIM mftmrr.. t ZONINGOOMMNTBt ' Zoning; Romewen MWIN0OapAI11 " !NT COMMlMre,: ReWew PWMOmRKSCOMMBNTal Reviewer. DLPARTMONT 11811 OOOUPANOY; Flea DRPARTMeNT.: Q eppmued wr comments ❑ dlsepproWd A rtorrylew ngtdr d tahtp VatueaAnt i -- 0( /Z 'd W A 3t310 Wtl t,ii tQZ �,•ke„ l/l 'd titit8 'IN 3MIS NdOI • { I l OZ 'H 'AV rwmwil lu; MechenWI: SERVICE REQUEST Date: 10/14/2003 Received: D Phone D Letter/Fax D In Person Referred by: D. Meixner Phone: 2819 Request No.: 2003-0253 Phone: Address: C 3625 Cha,e"::) District No. r DESCRIBE REQUESTNIOLATION: Complaint from constituent regarding number of tenants living at property at 3625 Chase. A Service Request has also been sent to APca regarding trash and weeds on this property. ACTION TAKEN: 10/16/03: This issue was addressed in Feb. and March, 2001. Judge Charles Rose ruled that although the property was (and is) currently zoned Residential-One, it may continue to operate as a legal non-conforming two-unit dwelling. At the time of the ruling, property owner Melody Magalei (303) 431-1634 was ordered to vacate the third unit of the dwelling. HISTORY: The house was built in 1941. At that time, the property was zoned Residential-Three. In 1963, the property was rezoned Residential-Two. In 1969, the property was rezoned Residential-One. On 10/16/03, I met with front unit tenant Ramona Lacrue (303) 298-3614, who stated that she and her seven (7) children reside in the six bedroom unit. She stated that her boyfriend, her sister, and her mother often visit. She stated that the rear unit is leased by a woman named Sharon (nothing further), and a friend. There is no violation. No more than three (3) unrelated people are permitted to live in an individual dwelling. This code has not been violated. The ro er was free of nuisance violations. Case closed. I NEXT FOLLOWUP DATE (on or about): Case closed. Response Completed by: C. Hagerman Date: 10/16/03 Department Director: - Date: - Police Case Number: - Date: - (Citizen Notitication of Disposition D None Ifrequested) D Copy of Form/Letter D Phone ~ Personal Visit C:\MyFiles\3625 Chase - Ilumber oftenanls.doc City of Wheat Ridge Planning and Development Department Memorandum TO: Cindy Hagerman, Code Enforcement Officer II FROM: Darin Morgan, Codes Administrator 0/ 3625 Chase Street Inspection, February 2, 2001 SUBJECT: DATE: February 2, 2001 Per the approval of the owner Melody Magalei, an inspection was performed in an effort to determine an approximate date when the construction took place to convert a two-car garage to living space. Upon arriving at the property, we inspected the northeast unit, addressed as A-2 first. The plumbing fixtures, specifically the water closet had a manufacture date of February 1983. All water lines are copper pipe with plastic waste and vent lines. There is an attic furnace in this unit with ductwork appearing to be ten to fifteen years old due to the condition of the materials. The structure is also wired with NM cable (ROMEX) through out this unit. If the structure was established in the 50's or early 60's it would more than likely be a two wire ungrounded system. I would estimate that this part of the structure was converted from a garage within the last IS to 20 years. The unit at the northwest corner of the structure did appear to be 1950 or early 60's construction due to the cast tile window sills, steel casement windows and bathroom fixtures. I would estimate that this part of the structure is pre 1969 and constructed before the city was incorporated. ~ BUILDING DEPARTMENT (303) 235-2855 CITY OF WHEAT RIDGE * * Correction Notice Job Located at ..610 2 -5 LhCdrL, I have this day inspected this structure and these premises and have found the following violations of City and/or State laws gov- erning same: , ;?-z - 6:---~J~ o~ tV ~ ~#J - / 'f'/3r::J.s /..-fc:o? I ;Per, 4:J<Jc .,/_/ 0-'0# tdfirr- O;"}V /'dL /j7 d , I (! 1 I c.."!rK'I'I')< ;UC'-- d,;cJ- vJ / 12o_)c ..-vn;? I ~t ~,,,,P;if, G.....'P,L- .5o~ .:1.../" 'Iv). --- r;..(-",I<;, _ bu'! tp/Gff'P/ I j., ..-;., _ fIt' 1 r f I 11-1<'/1.. / ;;, 0.-,.) .-v S ,pre".J LI vy>' -e; <p J, I ; ~ 117~,,~/k /;'dI'J -~},: ~f,,-( c'-i~~_1s 0<" ti'I"~? You are hereby notified to correct the foregoing violations. When corrections have been made, call for inspection. DIIte Inllp8Ctor for BuildIng Depl. FORM WR6-22 DO NOT REMOVE THIS TAG r~--'----'-~--"'---'-- . I , k f , I , t, BUILDING DEPARTMENT (303) 235-2855 CITY OF WHEAT RIDGE * * I I, ~. r t. [ . I \ , I i I J ~ t l f. I l r f Notice -? ],~ -". c, -' /- / rl" /,' C _ l'luY~t'" Job Located at I have this day inspected this structure and these premises and have found the following violations of City and/or State laws gov- erning same: ill:; ,/V'r/ 1-1 P I'P ,.--- I-'/''.>r J '/' 1-:(> ( . v"-- I ' J '/.t?~-I- '1 '.(..1,-, 1~1 J You are hereby notified to correct the foregoing violations. When corrections have been made, call for inspection. Date , ; j --' / J ! I / (".-.; ,,-~;r:/ , ;/ I / f..,..L t., !&" -. j ...,~-,,-t.:.c""'j,~'/ , Inopector for Building Dept. DO NOT REMOVE THIS TAG FORM WR8.22 1 j I I > ,~ I , I ! ; j i ~ - ~ i '0 tJp1, /;:-YI- "'/iH(Ar A~~ C'O'-ORp."P City of Wheat Ridge Planning and Development Department Memorandum TO: Jack Hurst, Acting City Manager FROM: Bob Gaspar, Building Inspector t$ c;. SUBJECT: Building Complaint At 3625 Chase Street DATE: October 19,2000 On October 13, 2000 I responded to a complaint of building without a permit. No evidence of building, building materials or tools were found, I did leave my card with a note to call me at City Hall. No one has called. No further contact will be made unless there is new evidence, bg