Loading...
HomeMy WebLinkAbout3771-3773 Oak StreetENGINEERING, LLC Structural • Residential & Commercial The Value Add Real Estate Co. Attn: Zach Spicer www.thevareco.com 720.205.8555 cell Dear Zach, 38405 XL "REVIEWED ti�G September 8, 2021 W heat [ icl�c "REVIEWED FOR CODE COMPLIANCE" These drawings were reviewed under the applicable laws in effect at the time of submittal. Reasonable effort was exercised in checking for code compliance. amendments thereto. Plan Reviewer DHartley Date 09/14/2021 MarioDigitally signed by Luis Mario Luis De Leon De Leon Date: 2021.09.08 16:32:52 -05'00' 1, Mario De Leon, a Registered Colorado Professional Engineer, License No. 38405, would like to thank - you for allowing me to visually inspect and approve your proposal to sawcut two existing egress window openings of the basement concrete foundation wall large enough to incorporate a 30"x 48" LS egress window at the property located at 3773 Oak Street, Unit #3773, Wheat Ridge, Colorado, 80033. I am not opposed to sawcutting the two existing egress window openings in concrete foundation wall large enough to incorporate the new 30" x 48" LS egress window in each bedroom area of the basement. A new header beam consisting of a 4"x 4"x 3/8" steel angle lintel beam will be required for framing of the window. The egress window construction will be done in accordance with the 2018 IRC and City of Wheat Ridge code amendments. The design wind speed load is Vult = 135MPH for Exposure Category C and 30psf for roof snow loading. In my professional opinion and based on my visual inspection, I believe that after sawcutting the two existing egress window openings large enough to install the 30"x 48" LS egress windows and incorporating the appropriately sized header beam for window framing, the structural integrity of the entire concrete foundation wall system should remain stable and continue to function as intended. Sincerely, CIAA fario De Leon, P.E. \� �Vlhear�/� Structural Engineer " :�/ J 6,G1/ao,ing 0,4'4c Basement Egress Window Design using 4"x 4"x 3/8" Steel 9/8/2021 Angle Lintel Header Beam Design Mario Luis Digitally signed by Customer Name: Zach Spicer for The VARECO Mario Luis De Leon Customer Address: 3773 Oak Street, #3773 Date: 2021.09.08 Wheat Ridge, CO 80033 De Leon 16:33:11 -05'00' Project Description: Basement Egress Window Header Beam using a 4"x 4"x 3/8" Steel Angle Lintel Beam (see drawing plans). Span length = 3'-0" and tributary width = 10'-0". Stl. Strength, Fy = 36 KSI (min.) Design Information: 2018 IRC, Wind Loading = 135 MPH for Risk Category II / Exp.0 Header Support Beam Condition - Floor and Roof Loads - Snow Area 115% Floor Load = 40LL + 12DL=Mpsf psf Roof Load = 30LL + 15DL = Span Length = Tributary Width = Materials and Design Properties: One 4"x 4"x 3/8" Steel Angle Beam Allowable Bending Stress, Fb = 19,800 psi Allowable Shear Stress, F, = 19,800 psi Allow. LL Deflect., 5LL = LL/360 = 0.10 in Allow. TL Deflect., 6TL= (DL+LL)/240 = 0.15 in Following info used to check Deflection, S Modulus of Elasticity, E = 29,000,000 psi Moment of Inertia, IX = 4.36 in Actual Bending Stress, f,,' Total Moment, MT = wL2/8 = lb -ft fb' = MT/SX = psi Actual Shear Stress, f.' Total Shear, VT = wL/2 = lbs f„'= VT/AX = psi Actual Deflections, 5,r.F z S 6LL = 5wLLL4 / 384*E*IX = O1 in STL = 5wTLL4 / 384*E*IX = 0.01 in $ PROVIDE ESCAPE AND RESCUE OPENING: 1) Minimum net clear opening area: 5.7 sq. ft. or 5.0 sq. ft. at grade floor or below grade 2) Minimum net clear opening height: 24" 3) Minimum net clear opening width: 20" 4) Maximum sill height: 44" Section Area, AX = 2.86 in 2 3 Section Modulus, SX = F::3.82 in 3840.5 z: � Works in Live Load Deflection Works in Total Load Deflection Ur9r�5 P,bwIt gs'"01% Ok hear �j J o 6'G11a'ing o"i'4 1* � 4 i CITY OF WHEAT RIDGE Building Inspection Division (303) 235-2855 Office INSPECTION NOTICE Inspection Type: �� F Job Address: 3771 Gi Permit Number: 2!-0 Z-0 0 -760 ❑ No one available for inspection: Time Re -Inspection required: Yes A When corrections have been made, schedule for re -inspection online at. h ttpYlwww.*5/?0e?2:,;7_lnspector: ci. wheaatridge. co. u�nspection Date: 5111-0 DO NOT REMOVE THIS NOTICE ♦ i CITY OF WHEAT RIDGE - Building Inspection Division (303) 235-2855 Office INSPECTION NOTICE Inspection Type: Job Address: Permit Number: ❑ No one available for inspection: Time AM/PM Re -Inspection required: Yes No When corrections have been made, schedule for re -inspection online at: hUp✓/www. ci. wheatridge. co. ustlinspection Date:/' Inspector: DO NOT REMOVE THIS NOTICE i CITY OF WHEAT RIDGE Building Inspection Division (303) 235-2855 Office INSPECTION NOTICE Inspection Type: / .D Job Address: Permit Number: ❑ No one available for inspection: Time Re -Inspection required: Yes No 4 When corrections have been made, schedule for re -inspection online at. http✓/www.ci. wheatridge.co. uarinspection Date:- Inspector: DO NOT REMOVE THIS NOTICE City of Wheat Ridge , Residential Roofing PERMIT - 202001760 PERMIT NO: 202001760 ISSUED: 09/02/2020 JOB ADDRESS: 3771 Oak St EXPIRES: 09/02/2021 JOB DESCRIPTION: Re -roof with asphalt shingles, removing one layer. Squares: 25; Pitch: 4/12 *** CONTACTS *** OWNER (720)298-1832 OAK LLC SUB (720)298-1832 JUAN MANDONADO 110079 MJF CONSTRUCTION *** PARCEL INFO *** ZONE CODE: UA / Unassigned USE: UA / Unassigned SUBDIVISION CODE: 103 / BLOCK/LOT#: 0 / *** FEE SUMMARY *** ESTIMATED PROJECT VALUATION: 6,425.00 FEES Total Valuation 0.00 Use Tax 134.93 Permit Fee 156.75 ** TOTAL ** 291.68 *** COMMENTS *** *** CONDITIONS *** ALL PITCHED ROOFS REQUIRE A MIDROOF INSPECTION REGARDLESS OF PITCH. FOR ROOF PITCH 6/12 AND OVER: Midroof & Final Roof inspections for ROOFS with 6/12 PITCH & OVER REQUIRE A 3RD PARTY INSPECTION. The 3rd party inspection report must be dropped off to the Permit Desk at the City of Wheat Ridge. The report MUST BE SIGNED by the Homeowner. REGARDING ROOF VENTILATION: Roof ventilation shall comply with Building Division Policy BD -18-001 for Balanced Ventilation Systems, or manufacturer installation instructions, whichever is more stringent. MIDROOF & SHEATHING: Effective December 1, 2014, asphalt shingle installations require an approved mid -roof inspection, conducted when 25-75% of the roof covering is installed, prior to final approval. Installation of roof sheathing (new or overlay) is required on the entire roof when spaced or board sheathing with ANY gap exceeding one half inch exists. Sheathing and mid -roofs may be called in at the same time, one hundred percent of the sheathing must be complete and 25-75% of the mid -roof may be complete. Asphalt shingles are required to be fastened to the roof deck with a minimum of 6 nails per shingle. Ice and water shield is required. Eave and rake metal is required. LADDER MUST BE SET FOR ALL ROOF INSPECTIONS: A ladder extending 3 feet above the roof eave and secured in place is required to be provided for all roof inspections. COMMERCIAL ROOFS: In order to pass a final inspection of elastomeric or similar type roof coverings, a letter of inspection and approval from the manufacturer technical representative stating that "the application of the roof at (project address) has been applied in accordance with the installation instruction for (roof material brand name) roof covering" is required to be on site at the time of final inspection. City of Wheat Ridge Residential Roofing PERMIT - 202001760 PERMIT NO: 202001760 ISSUED: 09/02/2020 JOB ADDRESS: 3771 Oak St EXPIRES: 09/02/2021 JOB DESCRIPTION: Re -roof with asphalt shingles, removing one layer. Squares: 25; Pitch: 4/12 I, by my signature, do hereby attest that the work to be performed shall comply with all accompanying approved plans and specifications, applicable building codes, and all applicable municipal codes, policies and procedures, and that I am the legal owner or have been authorized by the legal owner of the property and am authorized to obtain this permit and perform the work described and approved in conjunction with this permit. I further attest that I am legally authorized to include all entities named within this document as parties to the work to be performed and that all work to be performed is disclosed in this document and/or its' accompanying approved plans and specifications. Signature of OWNER or CONTRACTOR (Circle one) Date 1. This permit was issued based on the information provided in the permit application and accompanying plans and specifications and is subject to the compliance with those documents, and all applicable statutes, ordinances, regulations, policies and procedures. 2. This permit shall expire 365 days after the date of issuance regardless of activity. Requests for extension must be made in writing and received prior to the date of expiration. An extension of no more than 180 days made be granted at the discretion of the Chief Building Official and may be subject to a fee equal to one-half of the originalpermit fee. If this permit expires, a new permit may be required to be obtained. Issuance of a new permit shall be subject to the standard requirements, fees androcedures for approval of any new permit. Re -issuance or extension of expired permits is at the sole discretion of the Chief Building Official and is not guaranteed. 4, No work of any manner shall be performed that shall results in a change. of the natural flow of water without prior and specific approval. 5. The permit holder shall notify the Building and Inspection Services Division in accordance with established policy of all re uired inspections and shall not proceed or conceal work without written approval of such work from the Building and Inspection Services Division. 6. The issuance or granting of a permit shall not be construed to be a permit for, or an approval of, an violation of any provision of any applicable code or ap.f.Qrdinance or r9gulation of this jurisdiction. Approval of work is subject to field inspection. Signature of Chief Building Official Date REQUESTS MUST BE MADE BY 11:59PM ANY BUSINESS DAY FOR INSPECTION THE FOLLOWING BUSINESS DAY. Kimberly Cook From: no-reply@ci.wheatridge.co.us Sent: Wednesday, September 2, 2020 9:00 AM To: CommDev Permits Subject: Online Form Submittal: Roofing Permit Application Categories: Licensing Issue, Kim Roofing Permit Application THIS APPLICATION DOES NOT CONSTITUTE A PERMIT. DO NOT BEGIN REROOFING UNTIL PERMIT HAS BEEN ISSUED. Is this property Residential Commercial or Residential? How many dwelling units 3 or 4 units are on the property? PROPERTY INFORMATION Property Address Property Owner Name Property Owner Phone Number (enter WITH dashes, eg 303-123-4567) Property Owner Email Address 3771 Oak St Oak LLC 720-298-1832 vanessamandonado@gmail.com Do you have a signed Yes contract to reroof this property? CONTRACTOR INFORMATION Contractor Business MJF Construction Name Contractor's License 110079 Number Contractor Phone 720-298-1832 Number (enter WITH dashes, eg 303-123-4567) I Contractor Email Address vanessamandonado@gmail.com Retype Contractor Email vanessamandonado@gmail.com Address Attach City of Wheat 2020-09-02 084609.pdf Ridge Electronic Payment Form - **DO NOT ATTACH A PICTURE OF A CREDIT CARD** DESCRIPTION OF WORK TOTAL SQUARES of 25 the entire scope of work: Project Value (contract 5750 value or cost of ALL materials and labor) Are you re -decking the No roof? Is the permit for a flat Pitched roof (2:12 pitch or greater) roof, pitched roof, or both? (check all that apply) What is the specific pitch 4/12 of the PITCHED roof? How many squares are 25 part of the PITCHED roof? Describe the roofing Owens Corning Duration 30 yr materials for the PITCHED roof: Type of material for the Asphalt PITCHED roof: Provide any additional Remove 1 layer and replace with 30 yr dimensional shingles detail here on the description of work. (Is this for a house or garage? Etc) SIGNATURE OF UNDERSTANDING AND AGREEMENT 2 I assume full Yes responsibility for compliance with applicable City of Wheat Ridge codes and ordinances for work under any permit issued based on this application. I understand that this Yes application is NOT a permit. I understand I will be contacted by the City to pay for and pick up the permit for this property. I understand that work Yes may not begin on this property until a permit has been issued and posted on the property. I certify that I have been Yes authorized by the legal owner of the property to submit this application and to perform the work described above. I attest that everything Yes stated in this application is true and correct and that falsifying information in this application is an act of fraud and may be punishable by fine, imprisonment, or both. Person Applying for Juan Mandonado Permit Email not displaying correctly? View it in your browser. K i CITY OF WHEAT RIDGE Building Inspection Division 2 (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: ` P %- Lnil Yi ,hkrzi Al Q- gill %d, rrr:} f Job Address: -3721 Qnl( �1, Permit Number: 0j�02_�4 % ❑ No one available for inspection: Time &/PM Re -Inspection required: Yes (90 When corrections have been made, call for re -inspection at 303-234-5933 Date: I 1/ i L/ M Inspector: Dal)P, Lacltk DO NOT REMOVE THIS NOTICE i CITY OF WHEAT RIDGE _:�9�Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: Job Address:�1 �� �? ►� .` -� Permit Number: ❑ No one available for inspection: Time= — ,.IAM Re -Inspection required: Yes No When corrections have been made, call r re -inspection at 3'03-234-5933 Daterr ` Inspector P, DO NOT REMOVE THIS NOTICE M 1* � I i CITY OF WHEAT RIDGE _1w Vr- Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTN NOTICE 'S S7 I_ ? � 0 We,ooi (_C/Inspection Type: 500 - h �� lil n // !'e l-& Job Address: -3-7-71 D?" k S4 - Permit Number: m e ) Si D a" -j-7 8 I ❑ No one available for inspection: Time =a3 q PM Re -Inspection required: Yes No When corrections have been made, call for re -inspection at 303-234-5933 Date: /a /! Lq Inspector: —"ih DO NOT REMOVE THIS NOTICE S i CITY OF WHEAT RIDGE Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: Job Address: "3`7-71 Q a Ic S� Permit Number: P c 18 o 9 H -7,0 -!-A Sy /a 4, on ❑ No one available for inspection: Time ('- 13 (K,-, Re -Inspection required: Yes No When corrections have been made, call for re -inspection at 303-234-5933 Date: I o /9—inspector: 71- / / DO NOT REMOVE THIS NOTICE i CITY OF WHEAT RIDGE �1(30Building Inspection Division 3) (303) 234-5933 Inspection line 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: F Job Address: 3771 Oa Permit Number: (9-01610 1179 ❑ No one available for inspection: Time AM/PM Re -Inspection required: Yes A �Ire ''When correc ions have been made cal1--inspection at 303-234-5933 In 7_/� Date: G / Inspector: O NOT REMOVE THIS NOTICE 10 1* � 4 i CITY OF WHEAT RIDGE Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: -3 ► 3 - c vq A P Job Address: -_')-7-7/ O cLk S 4 -- Permit Number: 'D r 1!F D-9 9 i 1 0V CIA Palm ane> i r\L\r-�ncsP ❑ No one available for inspection: TimeaSIV,I%PM Re -Inspection required: Yes When corrections have been made, call for re -inspection at 303-234-5933 Date: 0i/,13)/,? Inspector: -T DO NOT REMOVE THIS NOTICE i CITY OF WHEAT RIDGE Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: Cov- (!:�o a Job Address: "3 '7 7 / Q ca. �cS� Permit Number: a 0 IS o L9 g 7 g V"'D M ❑ No one available for inspection Re -Inspection required: Yes No When corrections have been made, call?or�we-inspection at 303-234-5933 Date L.. Inspe-=�--� DO NOT REM' E THIS NOTICE A i CITY OF WHEAT RIDGE Building Inspection -Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: Cc v - Co v r- 4&, - Job Address: 3 -7 -7 1 Q cz Lr Permit Number: --,) 01 <a 0 a y -7 1 ❑ No one available for inspection: Time 4R = PM Re -Inspection required: Yes (40"j, When corrections have been made, call for re -inspection at 303-234-5933 Date: '/ Inspector: —7—b DO NOT REMOVE THIS NOTICE City of Wheat Ridge t ' Residential Remodel PERMIT - 201802478 PERMIT NO: 201802478 ISSUED: 09/11/2018 JOB ADDRESS: 3771 Oak St EXPIRES: 09/11/2019 JOB DESCRIPTION: Fire damage repair to replace electrical and plumbing fixtures, insulation, drywall, flooring, trim, door and 2 windows, cabinets and appliances - 744 sq ft total *** CONTACTS *** OWNER PAUL ERIC GC (720)301-8406 Earl A. Pfeufer 180288 1 -EAP SUB (303)956-8534 William F. Heffernan 120123 Green Mountain Systems LLC SUB (720)495-5880 Leonardo Pena 170359 Leonardo's Mechanical *** PARCEL INFO *** ZONE CODE: UA / Unassigned USE: UA / Unassigned SUBDIVISION CODE: 103 / BLOCK/LOT#: 0 / *** FEE SUMMARY *** ESTIMATED PROJECT VALUATION: 55,000.00 FEES Total Valuation 0.00 Plan Review Fee 500.37 Use Tax 1,155.00 Permit Fee 769.80 ** TOTAL ** 2,425.17 *** COMMENTS *** *** CONDITIONS *** All roughs to be done at Framing Inspection. Approved per plans and red -line notes on plans. Must comply with 2012 IRC, 2017 NEC and all applicable City of Wheat Ridge Municipal Codes. Work is subject to field inspections. City of Wheat Ridge Residential Remodel PERMIT - 201802478 PERMIT NO: 201802478 ISSUED: 09/11/2018 JOB ADDRESS: 3771 Oak St EXPIRES: 09/11/2019 JOB DESCRIPTION: Fire damage repair to replace electrical and plumbing fixtures, insulation, drywall, flooring, trim, door and 2 windows, cabinets and appliances - 744 sq ft total I, by my signature, do hereby attest that the work to be performed shall comply with all accompanying approved plans and specifications, applicable building codes, and all applicable municipal codes, policies and procedures, and that I am the legal owner or have been authorized by the legal owner of the property and am authorized to obtain his permit and perform the work described and approved in conjunction with this ermit. I further est th m le al tho ' d to inc a al[ entities named within this document as parties to the work to be per med a wor e �g me is closed i is document and/or its' ccompanying a proved plans and specifications. fp ^t� Sigt4ature—of O R or C t�� d'1 CTOR.,OCircle one) Date I. This permit was( issued based on fhe information provided in the permit application and accompanying Flans and specifications and is subject to the compliance with those documents, and all applicable statutes, ordinances, regulations, policies and procedures. 2. This permit shall expire 365 days after the date of issuance regardless of activity. Requests for extension must be made in writing and received prior to the date of expiration. An extension of no more than 180 days made be granted at the discretion of the Chief Building Official and may be subject to a fee equal to one-half of the originalpermit fee. 3. If this permit expires, a new permit may be required to be obtained. Issuance of a new permit shall be subject to the standard requirements, fees androcedures for approval of any new permit. Re -issuance or extension of expired permits is at the sole discretion of the Chief Building Official and is not guaranteed. 4. No work of any manner shall be performed that shall results in a change of the natural flow of water without prior and specific approval. 5. The permit holder shall notify the Building and Inspection Services Division in accordance with established policy of all required inspections and shall not proceed or conceal work without written approval of such work from the Building and Inspection Services Division. 6. The issuance or granting of a ermit shall not be construed to be a permit for, or an approval of, an violation of any provision of any applicable code or any ordinjile or regulation of this jurisdiction. Approval of work is subject to field inspection. Signature of Rief hu-ildfng Official Date REQUESTS MUST BE MADE BY 11:59PM ANY BUSINESS DAY FOR INSPECTION THE FOLLOWING BUSINESS DAY. City of �W heat midge MUNITy DEVELOPMENT Building & Inspection Services Division 7500 W. 29t1 Ave., Wheat Ridge, CO 80033 Office: 303-235-2855 * Fax: 303-237-8929 Inspection Line: 303-234-5933 Email: permits(a)-ci.wheatridae.co.us FOR OFFICE USE ONLY Date:������� Plan/Permit # ano Plan Review Fee: Building Permit Application *** Please complete all highlighted areas on both sides of this form. Incomplete applications may not be processed. *** Property Address: 3-7 / / C> , k-- S ` ' Property Owner (please print): P 4t 1s Phone:,30j Z Property Owner Email: fir%. -J �� �� / 1 L,,; �' N�_% % e C�✓� l Tenant (Commercial Projects Only) Property Owner Mailing Address: (if different than property address) Address: ��> Ste/ vr/` i,�/ 1--A City, State, Zip: C Gi �Z Arch itect/Eng1neer E-mail: Contractor: I — '�E�P ee City of Wheat Ridge License #, Phone: Phone: 7 -z� d 3,--'� 1 Contractor E-mail Address: ®� `� i �7/ 67 f C For Plan Review Questions & Comments (please print): CONTACT NAME (please print): �L— ��L�64��Id4=e: -7 Z G I �G CONTACT EMAIL(p/ease print): Sub Contractors (Must provide Wheat Ridge License No.): Electrical: Plumbing: Mechanical: W.R. City License # W.R. City License # W.R. City License # Other City Licensed Sub: Other City Licensed Sub: City License # City License # ❑ COMMERCIAL RESIDENTIAL Description of work: For ALL projects, provide a detailed description of work to be performed, including current use of areas, proposed uses, square footage, existing condition and proposed new condition, appliance size and efficiency,, type and amount of materials to be used, etc/ !J \ C/ Jlii/ L"(� �//.'� C , P,4 U i✓ / - //��(%/� � ��/Sl%� 1 e R//4 /f F FEW g 3/ t r� Sq. FULF 7 BTUs Amps Squares Gallons Project Value: (Contract value or the cost of all materials and labor included in the entire project) OWNER/CONTRACTOR SIGNATURE OF UNDERSTANDING AND AGREEMENT I hereby certify that the setback distances proposed by this permit application are accurate and do not violate applicable ordinances, rules or regulations of the City of Wheat Ridge or covenants, easements or restrictions of record: that all measurements shown and allegations made are accurate; that I have read and agree to abide by all conditions printed on this application and that I assume full responsibility for compliance with applicable City of Wheat Ridge codes and ordinances for work under any permit issued based on this application; that I am the legal owner or have been authorized by the legal owner of the property to perform the described work and am also authorized by the legal owner of any entity included on this application to list that entity on this application. I, the applicant for this building permit application, warrant the truthfulness of the information provided on the application. CIRCLE ONE: Signature (first Printed Name: of (OWNER) (CONTRACTOR) DATE: — / ZONING COMMENTS: Reviewer: BUILDING DEPARTME T COM NTS: Z Reviewer: 5i�jj / A'111� 1 k PUBLIC WORKS COIENTS: Reviewer: DEPARTMENT USE ONLY OCCUPANCY CLASSIFICATION: r CONSTRUCTION TYPE: lX (0 Building Division Valuation: 55, oz_ F C E I V E D SEP 0 Per t e City Of Wh6atp, i COMMUMTY DEVELOPMENT SUB -CONTRACTOR AUTHORIZATION FORM This form must be signed by each sub -contractor. Subcontractor's City of Wheat Ridge License number must be provided in the applicable space. This form will not be accepted with missing information. Project Address: l / �jc E! , Pc Permit #:F U, General Contractor: %— Electrical Sub -Contractor Company Name: State License #: Phone #: Master #: Wheat Ridge License #: _ (required field) Signature of Authorized Agent Date Plumbing Sub -Contractor Company Name: , 2cistJJUs Phone #:� State License #: VO 3 -6,7 Master #: Wheat 'dge License #: (%� (required field) Sign a of Author' d Agent Date Mechanical Contractor Company Name: Phone: Wheat Ridge License #: (required field) Signature of Authorized Agent Date City of W heatj�idge COMMUNITY DEVELOPMENT SUB -CONTRACTOR AUTHORIZATION FORM This form must be signed by each sub -contractor. Subcontractor's City of Wheat Ridge License number must be provided in the applicable space. This form will not be accepted with missing information. Project Address: �7 71 (J%'�� Permit #: General Contractor: % t d P Electrical Sub -Contractor Company State License #: �'2 "Z/ Master #: 4) Wheat Ridge License #: Ali%- (required field) Signature of Author ed Agent Date Plumbing Sub -Contractor Company Name: State License #: Wheat Ridge License #: Signature of Authorized Agent Mechanical Contractor Company Name: Phone #: Master #• _(required field) Date Phone: Wheat Ridge License #: (required field) Signature of Authorized Agent Date Kemove MIS MCI 01151 1111A1 a11VrVW%1W@@. ..r •. _ ._ at o'?al Fenie ra �Q ? Pella Corporation 10 Basic New Construction Sliding Window Annealed OXO Vent]Fixed Advanced Loin — E High Altitude with Argon Gas P E L — N —105 — 00045 — 00001 TherMaWP 6yqrl?� ENERGY PERFORMANCE RATINGS U — Factor i Solar Heat Gain Coefficient 0.29 1 1.65 i n_�n u.s.11 — ADDITIONAL PERFORMANCE RATINGS Visible Transmittance 0.57 Manufacturer stipulates that these ratings conform to applicable NFRCProcedures Mole product performance. NFRC ratings are determined far a fixed sof far determining and a specific product size, NFRC does not -eco r�mend any products and environmental conditions ti,e suitabilit r of any product for any does not warrant or t the Della web site at www.pella Cco�m�co�se. For more information. call X641 �621— visit the NFRC web site at www.nf�c.org �� 1� Reservoirs Environmental, Inc. Effective January 1, 2015 Reservoirs Environmental QA Manual T:\QAQC\Lab\Reservoirs Environmental QA Manual.doc REI LAB Resery©yrs Environmental, Inc. T March 29, 2018 Steve Krutzsch Twenty9Eleven Inc. 5445 W. Caryl PI. Littleton CO 80128 Dear Customer, Subcontract Number: Laboratory Report: Project # / P.O. # Project Description: NA RES 404501-1 18-0312 3771 Oak St. Reservoirs Environmental, Inc. is an analytical laboratory accredited for the analysis of Industrial Hygiene and Environmental matrices by the National Voluntary Laboratory Accreditation Program (NVLAP), Lab Code 101896-0 for Transmission Electron Microscopy (TEM) and Polarized Light Microscopy (PLM) analysis and the American Industrial Hygiene Association (AIHA), Lab ID 101533 - Accreditation Certificate #480 for Phase Contrast Microscopy (PCM) analysis. This laboratory is currently proficient in both Proficiency Testing and PAT programs respectively. Reservoirs Environmental, Inc. has analyzed the following samples for asbestos content as per your request. The analysis has been completed in general accordance with the appropriate methodology as stated in the attached analysis table. The results have been submitted to your office. RES 404501-1 is the job number assigned to this study. This report is considered highly confidential and the sole property of the customer. Reservoirs Environmental, Inc. will not discuss any part of this study with personnel other than those of the client. The results described in this report only apply to the samples analyzed. This report must not be used to claim endorsement of products or analytical results by NVLAP or any agency of the U.S. Government. This report shall not be reproduced except in full, without written approval from Reservoirs Environmental, Inc. Samples will be disposed of after sixty days unless longer storage is requested. If you have any questions about this report, please feel free to call 303-964-1986. Sincerely, Jeanne Spencer President P: 303-964-1966 F:303-477-4275 5801 Logan Street, Suite 100 Denver, CO 80216 Page 1 of 1 1-866-RESI-ENV www.reilab.com � (3 Z Q � Z W 2 Z O > Z W Cl) ce O � W U) W ce 0 \§5 CD f E k E k z a E z -E 0 ��/-6 U) \ \ \ k k 0�000c» � 04 t w ( ] f a ® $ $ 0 2 Cl q CO £ z22 / EA \ c« m 2 r 0 0 0 p 0 0 0 0 to }§2 0) /ƒ E E / CIA C4 C4 a© z z z z z z z > } � w § Q•.......... ■ 0 ■ � _ _ 0 to £ UQ U n r 2 g r 2 U)� 2 200 C ] \ c ® t 0f -Se % j2 SD \ f k 2 a CL a) \ / \ c & k \ £ ƒ \ \ \§\ƒi77fƒ EE£E702Es7 3 8# 2£ 8/ E E k/ k/ k 0 2 ��4�«2=0/6/ <» w I < m o c w< m<= o 'IT $ $ / § LO LO g 2 & w w LU {mak 7 C149 Cl) �k� \ ƒ / city o W1h®at gimme d (3 Z J Q Z W 2 Z 0 Z W U) ce0 LU N NWN cc U Q `a EE 0 0 W W iO� m� J Q F r cc N I E N O W c t0 U 7 Q o m a m j •- O �o E v F: It O T Q it it E 0 w N Z F- F- 0 a O -o 0 _a � U U E m Z a E zw w CL .0 o ° E o aa�-0 C C C y t W N N N ip N co O N m N t 0 t6 2 C j w to O CO CO O til O 00 00 to 00 00 O OO C Z C O O O h 0 0 m ti O O O re Lt. 0 Q E O U 0 0 \ LO O O O O LO O O O N N N N Z ino 0'' a) c Q LL Q O U R .4) Q Q N N Q Q Q N N Q Q Q Q Z Z Z Z Z Z Z Z Z w ........ O d tQ d 4 r s s L s @ to O (D O to O to to Lo to to to U) a v T N N NN T T T� CO N .L Ln .L m m C Y Y U U coQ Q fN6 f�6 LUU co ) a 3 3 E E C c C c U) cn N O a) N a) CL `d `d � a o. -o fl. o f m E v O O o m O O O m coi E C ° E O'p'a c - O'p'O a) a) n. :3 Q) CD co 0- :3 44) a) a; 2E d 3 L t L d m 3 N N c s �c c c c c O O F- 0 0� m Ff--• Ff°- _I Q >- uj a' Q m U Q W Q m U 0 W Q m Q O T N Cl) L to to to to T T T T E O O O to 3 N N N N J W W W W � L a to T N L) U) 2 Z 2 = S 1 IF city °{ O aw M; 1411 i3 a -SaLmo ww" so 91"Now SM3,w" 0 uj a 0 j LL LL E ffi n 0 cc > vftv-i vov% E W) jo n I AIR saxo and MWAFV woug pppxqw 9 A SOA (9U1S1 *—.OAWMSW4S M; 1411 -SaLmo ww" so 91"Now SM3,w" v j LL LL E ffi cc vftv-i vov% E W) jo n I AIR saxo and MWAFV woug pppxqw 9 A SOA (9U1S1 *—.OAWMSW4S B m AD If- VwwovWJAwWW*3 t"Wompolo C14 w P JO I* AtmQCPAdW* w�m S'ONOWISIStO w uj 4-3 ` RS'rra+o:Y Wvw -PW mAWknON4 • -6 M ROR I sawros" of a-4&*WA'd-al ow" Swim '=*I - Afin Y411.0 SOMI Vow - on t "aid paqx4-m ;M. 0.0" *m" tM%o M 4M _QW) -1. O,'V ZOWI 11 PAAn "3HV W3 Wammeno Uad%u awl -VJ Amod uod- Lees mn M; 1411 0 0 ul CL ut"I v j LL LL E ffi E 9 A Lz 0 t 0 0 ul CL ut"I ,\go LL LL 4L E 9 A Lz t w ;U, vo� m0 IK en — LO 31 ,\go TWENTY EL—EVEN ENVIRONMENTRL TESTING Asbestos Inspection Report t 3771 Oak St Wheatridge, CO. 80226 Report Date: 03/29/2018 Inspection/Testing Date: 03/27/2018 Job# 18-0312 Prepared By Steve Krutzsch Twenty9Eleven Environmental Testing Colorado Certified Asbestos Building Inspector Certification No. 23844 Certified Firm No. ACF -24157 CNLy 01 �J shat r�c1V*�`. Limited Scope of Report The asbestos inspection performed for client was designed to identify suspect asbestos containing building materials in the affected areas of the above -referenced subject property as they existed at the time of the inspection. The inspection was limited to those areas that were visually and physically accessible. The inspection was not a risk assessment, physical inspection of systems, structure, or components of the subject property, as it relates to their serviceability. The inspection was performed in accordance with the Standards of Practice of the Colorado Regulation 8 Part B in effect at the time of this Inspection. This inspection is not intended to be technically exhaustive. The Inspector has prepared this written asbestos Inspection Report for the sole use and benefit of the client. The asbestos inspection report shall identify, report, and make recommendation for future evaluation. Client agrees to read the entire asbestos inspection report when received and shall promptly call the inspector with questions or concerns regarding the report. The use of this report and information contained herein by others, in whole or in part, is not authorized without the written mutual consent of the client and Twenty9Eleven, Inc.. Purpose and Scope The purpose of this inspection was to conduct a visual asbestos inspection and to collect necessary samples to determine the presence or absence of asbestos within the subject property in the affected areas only. The scope of this report included a visual inspection of all affected rooms and/or areas throughout the subject property for visible suspect ACM (asbestos containing materials). This does not include any materials that were covered or hidden by walls, structures, carpeting, wood flooring, multiple layers, wallpaper, texturing, etc. However, the inspector made every reasonable effort to access and identify all suspect ACM. Bulk asbestos samples were randomly collected from homogenous areas of suspect ACM by Steve Krutzsch, an EPA/State of Colorado Certified Asbestos Inspector. Homogenous areas are defined as any area with the same material, texture, and color. If any of these variables differs between materials or if for any reason the inspector feels the materials might be different in any respect (such as materials being installed at different times even though they appear similar), separate sets of samples must be taken from each homogenous area. Representative bulk samples were taken from similar materials, but this does not guarantee that materials of similar appearance are of the same composition. Even similar materials are subject to uneven mixing and distribution and random sampling can miss ACM. 2911 used reasonable diligence and its professional judgment consistent with industry standards to identify all suspect ACM. Performance of this asbestos inspection is intended to reduce, but not eliminate, uncertainty regarding the presence of ACM relating to the above referenced property. No guarantee: 2911 cannot be he(Wheat accountable for restrictions placed on us by the client, conditions or information that remained city of unknown, or areas that were inaccessible at the time of the inspection. Ridge Bulk Samples were analyzed by Polarized Light Microscopy (PLM) in general compliance with guidelines established by the US EPA (40 CFR Part 763, Subpart F, Appendix A). Asbestos concentrations were visually estimated and/or point counted by the laboratory and reported in percent for each layer of the sample. The assessment was executed in accordance with the authorized scope of work. If the scope of work is changed, the inspector must be informed, and an addendum made to this report. This report is solely a record of activities, observations, analytical results, and recommendations performed to date. Regulatory Review EPA and the Colorado Department of Public Health and Environment (CDPHE) regulate all building materials that contain greater than 1% asbestos as determined through PLM Analysis. OSHA regulates all building materials that contain smaller amounts of asbestos (even trace concentration as determined by PLM analysis). EPA and CDPHE Regulation No. 8, Part B, requires that suspect ACM in buildings built prior to 1988 be assumed to be asbestos or an inspection be conducted prior to demolition or remodeling activities that could disturb ACM. However, with the North American Free Trade Agreement in effect and trade with countries such as Canada, Mexico, and China, it can never be determined that a material is not asbestos containing (even if it was produced after 1988) unless it is tested by a certified state inspector. The EPA and CDPHE require all friable and non -friable ACMs in the affected area(s) be removed prior to renovation activities that may disturb the ACM, and all friable ACM must be removed prior to demolition. Removal or management of regulated ACM is only required if they may be damaged or disturbed during remodeling, demolition, or burning. In some circumstances, "point count" analysis is required for bulk samples previously analyzed by PLM. Point counting is a more detailed means of analysis than standard PLM. Federal and State agencies define ACM as materials containing greater than 1% asbestos. The NESHAP regulation requires that if standard PLM analysis determines that a sample contains less than 10% asbestos, the material must be considered asbestos containing or be point counted. Even if the sample is less than 1% by standard PLM, the material either must be assumed to be ACM or point counted. If the point counting analysis is different than the PLM analysis, the point counting results take precedence over the PLM. If standard PLM analysis determines that a material has no asbestos or that the material contains greater than 10% asbestos, point counting is not necessary. City of Wheat Riage Di Background Sam, with Project X, requested an asbestos test to determine in building materials contain asbestos before they proceed with the mitigation process. Sampled Bulk Materials • Vinyl Tiles • Mastic • Drywall • Texture, Joint Compound, Tape Homogeneous Areas (HA in RED Contain Asbestos) • Homogeneous Area 1: ➢ Entire Unit -Walls and Ceilings • Homogeneous Area 2: ➢ Kitchen, Bathroom Floors Drywall, Texture, Joint Compound, Tape Vinyl Tiles, Mastic 975 sqft 110 sgft Cary of iiding Diriso Sampling The Inspector determined that it was necessary to collect 7 bulk samples from the various homogenous areas (see the Asbestos Sampling below for exact areas). All samples were submitted to an accredited third party independent laboratory. The laboratory results are attached to and incorporated into this report. Homogenous Area Sample # Sample Location Friable? Classification :t. HA1-1 Kitchen/Dining/Family Rms 4'(- Significantly Damaged HA1-2 Kitchen/Dining/Family Rms Yes Significantly Damaged HAI -3 Family Room Yes Significantly Damaged HA1-4 Bathroom Yes Significantly Damaged HAI -5 Bedroom Yes Significantly Damaged #2 HA2 -1 Kitchen Floors No Significantly Damaged HA2 -2 Bathroom Floors No Significantly Damaged Conclusion Asbestos containing building materials avl.i_°u %,". found in the samples analyzed by the laboratory. The affected building materials ®O need to be removed by a certified abatement company 2911 assumes no liability for any loss, injury, claim for damages arising directly or indirectly from any use or reliance on this report or the opinions expressed herein. 2911 makes no risk assessment, warranty, guarantee or insurance policies of any kind, express or implied. This report is limited only to the samples taken and locations sampled. There are no risk assessments, warranties, guarantees, or insurance available or provided by 2911. Additional sampling may be needed to further identify other pollutants, or other mold/fungus affected areas inside the subject property. This report was prepared pursuant to the contract 2911 has with the client. That contractual relationship included an exchange of information about the subject property that was unique and between 2911 and its client and serves as the basis upon which this report was prepared. Because of the importance of the communication between 2911 and its client, reliance or any use of this report by anyone other than the client, for whom it was prepared, is prohibited and therefore not foreseeable to 2911. No warranty is made. 2911 liability and that of contractors and subcontractors arising from any service rendered hereunder shall not exceed the total fee paid by the client to 2911. Thank you for the opportunity to work with you on this project. Please call at 720-660-1752 with any questions or concerns. Thank you. Sincerely, Steve Krutzsch Twenty9Eleven Environmental Testing Colorado State Certified Asbestos Inspector, 23844 City of Wheat Ridge wilding yV S V O 1; 2 CIA 1; 2 0 'o C) (0 U m EL X t. < 4 �l8 � Colorado Dement of Public Health i and Environment ASBESTOS CERTIFICATION* This certifies that l Steve Krutzsch Certification No.: 23844 has met the requirements of 25-7-507, C.R.S. and Air Quality Control Commission Regulation No. 8, Part B, and is hereby certified by the state of Colorado in the following discipline: l Building Inspector* Issued: August 10, 2017 .r Xpires.. August 10, 2018 -Ed, t.djkWei5 valid Of* Willi file pe"Miea of a =rarw Diti.*az revcd fralnhag coaarso curl. radoaa - €., the &w*ypc std akore- �iedApC D SEffk sf. _ � "Y Qf VWheat Ride ruiidinq DF• isen City of See attached list for additional requirements that Wheat�ge may apply to this project. COMMUNITY DEVELOPMENT City of Wheat Ridge Municipal Building 7500 W. 29" Ave. Wheat Ridge, CO 80033-8001 P: 303.235.2855 F: 303.237.8929 Review is limited to the contents of the plans submitted and any errors or omissions contained herein shall not be construed as permission to allow any conditions to exist in violation of the codes of the City of Wheat Ridge Rough Framing and Wood Requirements The complete rough inspection is to be made after the rough framing, rough electric, rough plumbing, and rough heat and ventilation are complete. The building should be fully enclosed with the roof covering and siding in place. 2 Fire blocking shall be installed to cutoff all concealed draft openings in the following locations: (IRC 302.11) A. In concealed spaces of stud walls and partitions, including furred spaces, vertically at the ceiling and floor levels, and at 10 -feet horizontal intervals. B, At interconnections between concealed vertical and horizontal spaces such as occur at soffits, drop ceilings, and cove ceilings. C. In openings around vents, pipes, ducts, cable, wires, chimneys, fireplaces, and similar openings that afford a passage for fire at ceiling and floor levels. D. In concealed spaces between stair stringers at the top and bottom of the run, and between studs in line with the run of the stairs at unfinished walls. 3 Safety glazing shall be installed in the following hazardous locations and be permanently labeled as safety or tempered glazing: glazing panels in doors; glazing enclosing spas, bathtubs or showers; glazing panels adjacent and within 24 -inches of the edge of a door; glazing panels greater than 9 square feet within 18 - inches of the floor; glazing used for railings; glazing used for barriers for swimming pools and spas; and glazing enclosing stairways, landings, and ramps within 36 -inches horizontally of a walking surface. See the Boulder County Land (IRC R308) Heating and Ventilation Requirements 4 Bathroom exhaust fans shall exhaust directly to the exterior and must be provided in bathrooms where windows of at least 3 square feet are not provided. The mechanical ventilation must be capable of providing an exhaust capacity of 50 cfm intermittent or 20 cfm continuous exhaust. (IRC R303.3, M1507.4) 5 Appliances and equipment shall be installed in accordance with the conditions of their listing. Manufacturer's installation instructions must be available at the time of the inspection. (IRC G2408.1, M1307.1, M1401.1,(M1902.2) 6 Appliances shall be accessible for inspection, service, repair and replacement without removing'perm�neN construction. 30 -inches of working depth and width shall be provided in front of the control side of an appliance. (IRC M1305.1) ( w "eat Ft►d9e 7 Combustion air is required for all liquid fuel, solid fuel and gas appliances. (IRC M1701.1, G Electrical Requirements 8 All hot, neutral, and grounding conductors in electrical boxes shall be tied together with a mechanical connection at the time of rough inspection. 9 Recessed lighting fixtures must either be IC -rated or installed in a sealed box in which the insulation is at least 3 -inches from the light fixture. All recessed lights must be tightly sealed or gasketed to prevent air leakage through the fixture into the ceiling cavity. (IRC N1102.4.5) 10 Tamper -resistant Receptacle outlets are required in every kitchen, family room, dining room, living room, parlor, library, den, sunroom, bedroom, recreation room or similar dwelling areas spaced so that no point along the wall line exceeds 6 -feet from an outlet. (IRC E3901, E3902, and 4002.1-4002.14) 11 Counters 12 -inches in width or wider shall have receptacles placed no more than 20 -inches above the counter top and spaced so no point exceeds 24 -inches from an outlet. B Island and peninsula counters with a length at least 24 -inches and a width of 12 -inches or greater must be equipped with at least one outlet. C. At least one receptacle shall be installed in a bathroom within 36 -inches of each basin. 12 At least one receptacle outlet must be installed in each laundry, basement, attached garage and detached garage with power. F. At least one receptacle outlet that is accessible while standing at grade level and located not more than6-feet, 6 -inches (1981 -mm) above grade, shall be installed outdoors at the front and back of each dwelling unit having direct access to grade. Balconies, decks, and porches that are accessible from inside of the dwelling unit and that have a usable area of 20 square feet. F. Attics or crawlspaces containing equipment must be provided with at least one receptacle outlet within25-feet of the equipment. G. Hallways 10 -feet or more in length. 13 Two 20 -amp rated branch circuits shall serve receptacles in the kitchen, pantry, breakfast area, and dining area. At least one 20 -amp branch circuit shall supply bathroom receptacles and at least one 20 -amp branch circuit shall supply laundry. (IRC E3703.2, E3703.3, E3901) 14 Ground fault protection shall be provided on all 125 -volt, single phase, 15 and 20 -amp receptacles in the following locations: bathrooms, garages, unfinished grade level accessory buildings, at exterior locations, crawlspaces, unfinished basements, kitchen counters, within 6ft. of laundry, utility and wet bar sinks, boathouses, hydro massage, spa and hot tub locations. Receptacles must be in a readily accessible location. (IRCE3902, E3902.11) 15 Combination type Arc -Fault circuit interrupters must be installed on all 120 -volt 15 and 20 -amp branch circuit outlets in Receptacle outlets are required in every family room, dining room, living room, parlor, library, den, sunroom, bedroom, recreation room, hallway, closets, and similar dwelling areas. (IRC 3902.12) 16 At least one wall switch -controlled lighting outlet shall be installed in every habitable room, bathroom, hallway, (10ft) stairway, attached garage, detached garage with electric power, and at the ext0or side of each outdoor egress door having grade level access. Attics, under floor spaces, utility rooms nd basements containing equipment or used for storage must be provided with a switch Ruil(3inn r)ivisonJ 17 Smoke alarms shall comply with UL 217. Smoke alarms are to be powered by the building's wiring"Cperat'ed light. (IRC E3903)with battery backup and shall be interconnected so the actuation of one alarm will activate all alarms in the dwelling unit. Smoke alarms shall be installed in the following locations: (IRC R314) A. In each sleeping room; B, Outside each sleeping area in the immediate vicinity of the bedrooms; and C. One on each additional story including basements. 18 Carbon Monoxide alarms are required in a single-family dwelling that has fuel -fired appliance(s), or a fireplace, or an attached garage. The alarm must be installed within 15 -feet of the entrance to each sleeping room. Must be listed by a nationally recognized, independent lab. Plugs into a dwelling's electrical outlet and has a battery backup. They may be combined with a smoke -detecting device if the combined device complies with applicable law. (IRC R315) 19 Clothes closet lighting shall be limited to surface -mounted or recessed incandescent fixtures with completely enclosed lamps, and surface -mounted or recessed fluorescent fixtures.Surface mounted fixtures shall be installed on the wall above the door or on the ceiling with the following clearances between the fixture and the nearest point of a storage space: (IRC E4003.12)A. Incandescent fixtures or LED shall have a minimum 12 -inch clearance. B. Fluorescent fixtures shall have minimum 6 -inch clearance. Recessed fixtures shall be installed in the wall or ceiling with the following clearances: A. Recessed incandescent fixtures shall have a minimum 6 -inch clearance to the nearest point of storage. B. Recessed fluorescent fixtures shall have a minimum 6 -inch clearance to the nearest point of storage. 20 Working space must be provided around energized equipment for servicing and maintenance. The minimum dimensions shall not be less than 36 -inches in depth and 30 -inches in width in front of the equipment. Working space shall extend to at least 6 -feet, 6 -inches above the floor. (IRC E3405.2) 21 Electrical fixtures installed in wet or damp locations shall be installed so that water cannot enter or accumulate n wiring compartments or other electrical parts. Fixtures installed in wet locations must be labeled "suitable for wet locations". Fixtures installed in damp locations must be labeled "suitable for damp locations" or "suitable for wet locations". Switches or circuit breakers located in wet locations or outdoors must be enclosed in a weatherproof enclosure. Outdoor receptacles must have a weatherproof enclosure and an in -use cover. Cord -connected fixtures, hanging fixtures, track lighting, pendants, and ceiling fans shall not be located within3-feet horizontally and 8 -feet vertically from the top of a tub or shower rim. (IRC E4003.9, E4002.8, E4002.9,(E4002.10, E4003.9, E4003.10,E4003.11) Plumbing Requirements 22 DWV systems shall be tested on compellation of the rough piping installation by water or for piping system other than plastic by air with no evidence of leakage. Either test shall be applied to the drainage system in its entirety or in sections after rough piping has been installed .1) Water test 10 feet above the highest fitting connection or to the highest point of the completed system. The system shall prove leak free for 1,= -minutes. 2) Air test shall maintain Sibs of pressure for 15 minutes. / city of Wheat Ridge 23 Piping must be inspected and tested prior to concealing. It shall be protected against physic must be approved for use and bear the identification of the manufacturer. (IRC P2503, P2603, 24 Bathtubs, walls above bathtubs with shower heads, shower floors, and shower compartments shall be finished with a non-absorbent surface which extends to a height not less than 6' above the floor. Showers must have a minimum 900 square inches of interior area and a minimum dimension in each direction of 30 - inches. Shower valves must be pressure balance/thermostatic mixing valves. Shower receptors shall have a curb threshold not less than 1 -inch below the sides and back of the receptor. The curb shall measure a minimum of 2 -inches to a maximum of 9 -inches above the top of the drain. (IRC R307, P2708, P2709) 25 The centerline of toilets or bidets shall not be less than 15 -inches from adjacent walls or tub. Toilets, bidets, and lavatories must have a minimum clear space of 21 -inches in front of the fixture. Lavatories require a 4 - inch clearance to wall or to a toilet. (IRC P2705) 26 Showers and tub/shower combinations shall have control valves of the pressure balance, thermostatic mixing or combination pressure balance/thermostatic mixing valve types with high limit stop per ASSE 1016 or CSAB125.1. Tubs shall also have a control valve as listed for a shower or a water -temperature -limiting device that conforms to ASSE 1070. The high limit stop for a device shall be set to a maximum of 120*. (IRC P2708.3,P2713.3) 27 Shower doors shall have safety glazing; hinged show door shall open outward. (R308.4.5 , P2708.1) 28 Backflow prevention must be provided to prevent contamination of potable water. This includes but is not limited to: hose connections, irrigation systems, boilers, solar systems, fire sprinklers, and dishwashers. Backflow device must be inspected and approved by a 3rd party agency. (IRCP2902.2, Table P2902.3, P2717) Insulation 65 R-20 Walls R-49 Ceiling R-19 Crawlspace Window U -Factor .32 Floor R-30 66 Supply Ducts in attics shall be insulated to a minimum of R-8. All other ducts shall be insulated to minimum R-6. ( N1103.2.1) 67 Combustible insulation shall be separated a minimum of 3 -inches from fan motors and heat -producing devices. Insulation shields must be provided where vents pass thorough insulated assemblies and must terminate at least 2 -inches above attic insulation materials. Can lights must be airtight if located in the building envelope. (G2426.4) Class I or II vapor retarders are required on the interior side of the insulation in framed walls, floors and roof/ceilings of the building's thermal envelope. The vapor barrier is not required in construction where moisture or freezing will not damage the materials, or where the framed cavity (or space) is ventilated to a City o moisture to escape. A vapor retarder is not recommended on a concrete basement foundation Wall or in a shower /bath compartment (IRC 702.7, R702.7.1). Wallboard Requirements VVheat Ridge Iding 69 The garage shall be separated from the residence and its attic by materials of not less than %2 -inch gypsum board applied to the garage side. Garages beneath habitable rooms shall be separated from all habitable rooms above by not less than 5 8 -inch Type X gypsum board. Where the separation is a floor -ceiling assembly, the structure supporting the separation shall also be protected by not less than %2 -inch gypsum board. (IRC R302.6) Openings between the garage and residence shall be equipped with solid wood doors not less than 1 -inch in thickness, solid or honeycomb core steel doors not less than 1 -inch thick, or 20 -minute fire -rated doors. Openings are prohibited between garages and rooms used for sleeping. (11302.5.1 )Doors between attached garages and living space shall be weather stripped to the degree necessary to make them airtight and shall be self-closing and self -latching. 70 Nail spacing for gypsum board % gypum board Ceiling 16oc, 7", nails 12", Type S screws %2 wall spacing 24"OC, 8" nail spacing. 12"OCscrews. 5/8 ceiling board 16"OC, 7"nailsl2"spacing, screws 240C 8". 72 Water-resistant gypsum backing board used as the base or backer for adhesive application of ceramic tile or other required nonabsorbent finish material shall conform to ASTM C1396, C1178 or C1278. It is permitted on ceilings where framing spacing does not exceed 12 -inches o.c. for %-inch thick or 16 -inches o.c. for 5 8 -inch thick gypsum board. Water-resistant gypsum board shall not be installed over a vapor retarder in a shower or tub compartment and may not be used where there will be direct exposure to water, or in areas of continuous high humidity. All cut and exposed edges shall be sealed. (IRC R702.3.8) City of Wheat Ridge M All D, N - t� 12 7L)' �tU SOA 1eVf[w� au-> (P&k SH,4 L. L- COM P- y W Til zo 12 IRC 20 M NEC 041 ��W=tRjdg,-UNm Omto►MENT APPROVED Reviewed for Compliance 1� 'Z�4PIans E amine= Date Vs w ty of gurnft. The permit or approvol of pbns swifirations and c --pulp- shpts not be a permit joi ar on oW v i of o,W WAN t/on ro airy of the provisions or rhe buwmv code or of WW city ordYsonces. peffma ores~4 to Dow eudtorky ro .vWate or cancN Me ptaveiom aJ rhe �WldvsO codes a ~ ar0--" M Ot CMP $60 not 4 voNd. NAY V •VALU IF Fo2 I�INf�OWS : .32 City of Wheat Ridge ,Building Divison, 1 14 ' CITY OF WHEAT RIDGE Building Inspection Division (303) 234 -5933 Inspection line (303) 235 -2855 Office ' (303) 235 -2857 Fax INSPECTION NOTICE � ,+'f ; Inspection Type: � Cn s p , Job Address /Permit Number: 3771-73 r `( fi 2t}i� Li No one available for inspection: Time IP'4 > AM I M . Re- Inspection required: 'Yes No When corrections have been made, call for re -i pectin at 393- 234 -5933 Date: a Inspector: 7 DO NOT REMOVE THIS NOTICE i ♦ i CITY OF WHEAT RIDGE ` , Building Inspection Division (303) 234 -5933 Inspection line (303) 235 -2855 Office • (303) 237 -8929 Fax INSPECTION NOTICE Inspection Type: o7Vw,,sv ox- y ,& iee �A S Job Address: _ Z; 71 - 77ziAe <7 Permit Number: /Ze,�q>7 ❑ No one available for inspection: Time f ?,`.?o AM /M_- Re- Inspection required: Yes `ro When corrections have been made, calf for re at 303 - 234 - 5933 Date: 1 irk Inspector: ' e" DO NOT REMOVE THIS NOTICE " ' ' City of Wheat Ridge Res. Miscellaneous PERMIT - 100017 PERMIT NO: 100017 '.'ISSUED; ..01/04/2010 JOB ADDRESS:. 3771-7.7 Oak St. EXPIRES: 0.7/03/2010 DESCRIPTION: Replace 24 windows and 4 french'. doors Ref #100014 **'CONTACTS owner 303/229-5347 Mark Maryesh sub 303/798-3315 10.0001 Colorado Glass **-PARCEL INFO ZONE CODE: UA USE: UA SUBDIVISION:' 0191 BLOCK/LOT#: 0/ FEE SUMMARY ESTIMATED PROJECT; VALUATION: 5,833.33 FEES Permit Fee 162 .90 Total Valuation .00 Use Tax 105.00 _TOTAL !267.90 Conditions: Tempered glazing required within 24inches ,of doors and in tub enclosures. Subject to field inspections. I hereby certify that the setback distances proposed by this permit application. are accurate, and do not violate applicable ordinances, rules or regulations of the city 'of . wheat Ridge or covenants, easements or restrictions . of record;; that all measurements shown, and allegations made are accurate; that I have read and agree to abide by all conditions printed on this application and that I assume full responsibility for compliance:. with the Wheat Ridge Building Code (I B C) and all other: applicable Wheat Ridge Ordinances, for work under this permit. Plans subject to :field inspection. 8i5nature of contractor/owner date 1. This permit was issued in accordance with the provisions set forth in your application and is subject to the laws of the State of Colorado and to the Zoning Regulations and Building Codes of Wheat Ridge, Colorado or any other. applicable ordinances of the City.. 2. This permit shall expire 180 days, from the issue date. Requests for an extension must be received prior to expiration date. An extension maybe granted at the discretion of the Building Official 3. If this permit expires, za new permit may be. acquired for a fee of one-half the amount normally required, provided no ngwith successive phases of the job. Is and specifications shall not be construed tote a permit for, nor the building codes or any other ordinance, law;: rule or-regulation -'date BUILDING OFFICE: (303)235-2855 : 2q P)MV WnP` TATQVV `TnWT TRC:` WnT.TINATTTC RTTCTATWQQ nmv W HEgT ~oF 9 City of Wheat Ridge Building Division Date: / -Ll_ LO m 7500 W. 29th Ave., Wheat Ridge, CO 80033 Office: 303-235-2855 x Fax: 303-237-8929 Plan M 00<ORA00 Inspection Line: 303-234-5933 Permit Building Permit Application Property Address; _ 377/- 7-7 (Jr ~1lG $ I Property Owner (please print): Mailing Address: (if different than property address) Address: Phone: Zip: Contractor: ~dt 2~ CUSS Contractor License 1 0 J Phone 303- 1J Sub Contractors: Electrical City License Company: Plumbing City License Company Mechanical City License Company: Exp. Date: Exp. Date: Exp. Date: Approval: Approval: Approval: Use of space (description): Description of work: ZI - &t p/lvOtw R 4^ 4~elGver Construction Value: g 4'7X~ (as calculated per the Building Valuation Data sheet) 'Plan Review (due at time. of submittal): $ 1 Sq. Ft./L.Ft added: Squares BTU's Gallons Amps OWNER/CONTRACTOR SIGNATURE OF UNDERSTANDING AND AGREEMENT I hereby certify that the setback distances proposed by this permit application, are accurate, and do not violate applicable ordinances, rules or regulations of the City of Wheat Ridge or covenants, easements or restrictions of record; that all measurements shown, and allegations made are accurate; that I have read and agree to abide by all conditions printed on this application and that I assume full responsibility for compliance with the Wheat Ridge Building Code (I.B.C) and all other applicable Wheat Ridge Ordinances, for work under this permit. Plans subject to field inspection. CIRLCE ONE: (OWNER))(CONTRACTOR) or PERSONAL REPRESENTATIVE of.~(OW EE/R) (CONTRATOR) PRINT NAME: 840a v y C //~[ry SIGNATURE: 1 &GrIsl(,,I~•"--9 Date: 1 Cd 01:37 3036239175 MSS INC MOUNTAIN STATES STRUCTURAL, Inc. PAGE 01/01 636 Leyden Street Deaver, CO 80220-5332 Ph: 303-825-1572 lx: 303484-2376 stmetur2i.engiamr@yaboo.com December 29, 2009 Atka: Mr. Mark and Ms. Robbie Meryash ~ ,4 /6 3741 o.9 3+,, / j/ 199 LaRancheria ®93,33Y Camel Valley, CA. 93924 Re: Structural Observations of the 2nd Floor Porches/Stairs and Sidewalk Slabs at the Oakbrook Apartments 3773 Oak St. Wheat Ridge, CO MSS Project #09-096 Dear Mark and Robbie: A, representative of Mountain States Structural, Inc. visited the subject property on (6) occasions in October - December 2009. We were summoned by your agent, Mr. Jim Poster, and the contractor who was rebuilding the decks, Mr. Randy Quate of Real Welding Quality. We visited (3) times to consult on the project, (2) times to observe completed work, and a final time to discuss stair landing/sidewalk plans. We have bew supplied with copies of the tickets from the concrete supplier and bills of sale for the welded wire fabric and metal deck. They all meet the specifications provided by Mountain States Structural, Inc. Based on our conversations with the provider before and after the concrete stair landings and slabs were cast, we believe these concrete elements to be satisfactory. Based on the proof of materials and the in-place work observed, in our opinion, the deck replacments and stain upgrades wm in substantial compliance with the design and field directives issued by our office. Thank you for engaging our services on this project If you have any questions or comments, please call. Sincerely, Alan C. Stepneski, P.E. Principal 3773 Oak St Mountain States Struetural, lac. Page I of I 4' CITY OF WHEAT RIDGE Building Inspection Division 1~ro (303) 234-5933 Inspection line (303) 235-2855 Office - (303) 235-2857 Fax INSPECTION NOTICE Inspection Type: e: 9 Job Address/Permit Number: X77 /-7 ( £~R> ❑ No one available for inspection: Time'.P7 AM/ r~ Re-Inspection required: 'Yes 'When corrections have been made, call f Dr r -inspection at 303-234-5933 Date: -a Inspector: s DO NOT REMOVE THIS NOTICE INSPECTION RECORD OccupancViToe 'ZMSPECTiON LINE: (303) 234-5933 Inspections will not be made unless this card is posted on the building site Call by 3:00 PM to receive inspection the following business day. INSPECTOR MUST SIGN ALL, SPACES` PERTAINING TO THIS JOB' FOUNDATION INSPECTIONS DATE INSPECTOR ` INITIALS COMMENTS:. - Footings/Caissons -Stemwall (CEG) Concrete Encased Ground Reinforcing or Monolithic Weatherproof/ French Drain Sewer Service Lines Water Service Lines POUR NO CONCRETE UNTIL ABOVE HAS BEEN SIGNED CONCRETE SLAB FLOOR 'Electrical (Underground) Plumbing (Underground) Heating (Underground) DO NOT POUR FLOOR UNTIL ABOVE HAS BEEN SIGNED ROUGHS Sheathing Lath / Wall tie 'Mid-Roof Electrical Service Rough Electric Rough Plumbing Gas Piping Rough Mechanical ABOVE INSPECTIONS TO BE SIGNED PRIOR TO PROCEEDING Framing Insulation 'Drywall Screw FINALS Electrical -:Plumbing ; Mechanical? Roof Building Final Fire Department R.O.W & Drainage INSPECTIONS FOR PLANNING & ZONING, FIRE AND PUBLICE WORKS Parking & Landscaping SHOULD BE CALLED AT LEAST ONE WEEK PRIOR TO FINAL INSPECTIONS. ""NOTE: ALL ITEMS MUST BE COMPLETED AND APPROVED BY PLANNING AND ZONING,, BUILDING AND PUBLIC WORKS BEFORE A CERTIFICATE OF OCCUPANCY is ISSUED.. FINAL INSPECTION BY SHE BUILDING: DIVISION DOES NOT CONSTITUTE AUTHORIZATION OF A CERTIFICATE OFOCCUPANCY ` NOR PERMISSION FOR OCCUPANCY. OCCUPANCY NOT PERMITTED UNTIL CERTIFICATE OF OCCUPANCY IS ISSUED PROTECT THIS CARD FROM THE WEATHER " 1 City of Wheat Ridge Residential Roofing PERMIT - 092052 PERMIT NO: 092052 ISSUED:- 09/04/2009 JOB ADDRESS: 3771-73 Oak St.: EXPIRES.: 03/03/2010 DESCRIPTION: T/o: Install 22 sqs 'Tamko 25-yr 3-tab :CONTACTS owner ,831/236-8660 :Mark Meryash gc 248/594-3188 01-9232 Belfor.USA Group, Inc. **..PARCEL INFO ZONE CODE: -:UA USE: UA SUBDIVISION: 0191 BLOCK/LOT#: A/. **.:FEE SUMMARY ESTIMATED. PROJECT VALUATION: 6,541.00: FEES Permit Fee 181.10 Total Valuation , op Use Tax y~,) 117.74 /2'~~~rs t **.TOTAL 298.84 onditions: mail installation & mid-roof inspection required. Board sheathing spaced more. :hall a 1/2 of an inch apart requires plywood overlay on entire roof. ice and cater shield required from eave edge to 2'.. inside exterior walls.. Subject to field inspection.. I hereby certify that. the setback distances proposed by this permit application are accurate, and do not violate applicable ordinances, rules or regulations of the City of Wheat Ridge or covenants, easements or restrictions of. record; that all measurements shown, and allegations made are accurate; that I have read and agree to abide by all conditions printed on this application a d that I ass full responsibility for compliance with the Wheat Ridge Building Code (I.B.C) and all other - applicabl eat Ridge d' ces, work under this pe itM/moans subject to field inspection. Signature ntractor/owner . date ..This permit was issued. in accordance with the provisions set. forth in your. application and is subject to the -laws. of. the State of Colorado and to the Zoning Regulations and Building Codes of Wheat Ridge, Colorado or any other applicable ordinances of the City. This permit shall expire 180 days from the :issue date. Requests for an extension must be received prior to expiration date. An extension may be granted at the discretion of the Building Official. If this permit expires, a new permit may be acquired for a fee of one-half the amount normally required, provided no changes have been or will be made in the original plans and specifications and any suspension or abandonment has not exceeded one (1) year. If changes- have. been or if suspension. or abandonment exceeds one '(1) year, full fees shall be paid for a new permit. No work of any manner shall be done that will change the natural flow. of water causing a drainage problem. Contractor shall notify the Building Inspector twenty-.four (24) hours in advance for all inspections and shall.. receive 'written approval on`inspection ' card before proceeding with successive phases of the job. The issuance of a permit or the approval of. drawings and specifications shall not be construed to be a permit for, nor - an approval of~yj7 an olation of the provisions of the building codes or any other ordinance, law, rule or regulation. All plan subject to field inspections. ignature ohief/Building Official "date 1 :NSPECTION REQUEST LINE: (303)234-5933 BUILDING OFFICE:: (3.03)235-2855 :EQUESTS MUST, BE MADE. BY.3PM ANY BUSINESS DAY_ FOR INSPECTION -THE'FOLLOWING BUSINESS DAY..:` ,OF NtFiEgTQ,O City of Wheat Ridge Building Division m 7500 W. 29th Ave., Wheat Ridge, CO 80033 Office: 303-235-2855 * Fax: 303-237-8929 o Inspection Line: 303-234-5933 OCORPO Plumbing City License Company Contractor 411 Contractor License 1O?3 ~2 Phone: 3 O Sub Contractors: Electrical City License Company: Exp. Date: Exp. Date: Date: Plan Permit Mechanical City License Company: Exp. Date: Property Address; 3-771-7;? e5 /l S7 Property Owner (please print): Phone: ef9l'301 zvijlo Mailing Address: (if different than property address) Use of space (description): /a`7 !if/S Description of.work. ?ems o ~srF s 3x-.96 Sq. Ft./L.Ft added: Squares -2-04L BTU's _ Construction value: $ ~-e- (as calculated per the Buildinfl _ Valuation Data sheet) Plan Review (due at time of submittal): $ Gallons Amps OWNER/CONTRACTOR SIGNATURE OF UNDERSTANDING AND AGREEMENT 1 hereby certify that the setback distances proposed by this permit application are accurate, and do not violate applicable ordinances, rules. or regulations of the City of Wheat Ridge or covenants, easements or restrictions of record; that all measurements shown, and allegations made are accurate; that I have read and agree to abide by all conditions printed on this application and that I assume full responsibility for compliance with the Wheat Ridge Building Code (I.B.C) and all other applicable Wheat Ridge Ordinances, for work under this permit. Plans subject to field inspection. CIRLCE ONE:: (OWNER) (CO/NT CTOR) or PERSONAL REPRESEN ~TIVE of /NER) ONTRATOR) PRINT NAME: ~C✓lHiC L. y/' -W SIGNATURE: ~ Date: yqui'r"ed I Bldg Valuation: $ 1 Building Permit Application