The URL can be used to link to this page

Home My WebLink About11415 W I-70 Frontage Road NCity of Wheat Ridge Commercial Electric PERMIT - 201800666 PERMIT NO: 201800666 ISSUED: 03/08/2018 JOB ADDRESS: 11415 W I-70 Frontage RD N EXPIRES: 03/08/2019 JOB DESCRIPTION: Commercial Electrical permit install a UL listed hot table -request from Electrical Inspector. *** CONTACTS *** OWNER (303)423-9700 SIX OAK LIMITED PARTNERSHIP SUB (303)888-2968 Mike Mueller 090040 Five Star Contracting LLC SUB (303)587-2049 Juell Seidel 110222 Seidel Electric LLC *** PARCEL INFO *** ZONE CODE: UA / Unassigned USE: UA / Unassigned SUBDIVISION CODE: 420 / Storage Warehouse; 0 BLOCK/LOT#: 0 / *** FEE SUMMARY *** ESTIMATED PROJECT VALUATION: 1,400.00 FEES Total Valuation 0.00 Use Tax 29.40 Permit Fee 57.10 ** TOTAL ** 86.50 *** COMMENTS *** *** CONDITIONS *** Work must comply with the 2014 NEC, 2012 IBC and other applicable codes and ordinances. Work is ubject to field inspection. I, by my signature, do hereby attest that the work to be performed shall comply with all accompanying approved plans and specifications, applica le building codes, and all app4icable municipal codes, policies and procedures, and that I am the legal owner or have been authorized by the legal owner of the property and am autWorized to,- --am this permit and perform the work described and approved in conjunction with this permit. I further attest thatf am"re � gal ly'authori�� include all entities named within this document as parties to the work to be performed and that all wor -to be rfo ed is d' ed in this document and/or its' accompanying approved plans and specifications. Signature of OWNER r CONTRACT (Circle one) Date 1. This permit was issued information provided in thepermit application and accompanying plans and specifications and is subject to the compliance w' 4hoso documents, and all applicable statutes, ordinances, regulations, policies and procedures. 2. This permit shall expire 365 days after the date of issuance regardless of activity. Requests for extension must be made in writing and received prior to the date of expiration. An extension of no more than 180 days made be granted at the discretion of the Chief Building Official and may be subject to a fee equal to one-half of the originalpermit fee. 3. If this permit expires, a new permit may be required to be obtained. issuance of a new permit shall be subject to the standard requirements, fees androcedures for approval of any new permit. Re -issuance or extension of expired permits is at the sole discretion of the Chief Building Official and is not guaranteed. 4. No work of any manner shall be performed that shall results in a changeof the natural flow of water without prior and specific approval. 5. The permit holder shall notify the Building and Inspection Services Division in accordance with established policy of all required inspections and shall not proceed or conceal work without written approval of such work from the Building and Inspection Services Division. 6. The issuance or granting of a pe it shall not be construed to be a permit for, or an approval of, an violation of any provision of any applicable code or any ordmart ror regulation of this jurisdiction. Approval of work is subject to f eld inspection. Signature of Chief Building Official Date REQUESTS MUST BE MADE BY 11:59PM ANY BUSINESS DAY FOR INSPECTION THE FOLLOWING BUSINESS DAY. of W City Of ]�q�Wh6atl:,�i- COMMUNITYDEVELOPMET Building & Inspection Services Division 7500 W. 291h Ave., Wheat Ridge, CO 80033 Office: 303-235-2855 * Fax: 303-237-8929 Inspection Line: 303-234-5933 Email: permits ci.wheatridge.co.us FOR OFFICE USE ONLY Date: Plan/Permit # �(a f 0 0 G �A Plan Review Fee: Building Permit Application *** Please complete all highlighted areas on both sides of this form. Incomplete applications may not be processed. ** Property Address: 111414-5 W Owner (please print): Si V'O r1 l M % Ta.4ne ►'s h.I D Phone: Property Owner Emaii: k+ r hy kuru z Co m c: «<-, f- r1 e Mailing Address: (if different than property address) qd3 9700 Address: 5 _7 V� T -70 Fro ry4'RQ2 ped . N o r City, State, Zip: W% PCL+ i G 2 CO 6 Architect/Engineer: Architect/Engineer E-mail: Phone: Contractor: F -i V e 5TC c CO a4i-ac 61a LLC Contractors City License #: C 9 OCA q 0 Phone: 303 8? 8 9,9 ? Contractor E-mail Address: M I e 5 f -0.r Co @ a c I. CC M For Plan Review Questions & Comments (please print): CONTACT NAME (please print): M► k e, hl �Le I I E K_ Phone: 50-3 '333' a 9 (o Y CONTACT EMAIL(p/ease print): MA, Ve P+ V es+o ,r'CD @ GL O I co M Sub Contractors: Electrical:S2.Je1 tie( ric. W.R. City License # 1 �() a ), d_ Other City Licensed Sub: City License # City License # Plumbing: W.R. City License # Other City Licensed Sub: Mechanical: W.R. City License # Complete all information on BOTH sides of this form COMMERCIAL ❑ RESIDENTIAL Description of work: (Check all that apply) ❑ NEW COMMERCIAL STRUCTURE ❑ ELECTRICAL SERVICE UPGRADE ❑ NEW RESIDENTIAL STRUCTURE ❑ COMMERCIAL ROOFING ❑ COMMERCIAL ADDITION ❑ RESIDENTIAL ROOFING ❑ RESDENTIAL ADDITION ❑ WINDOW REPLACEMENT ❑ COMMERCIAL ACCESSORY STRUCTURE (Garage, shed, deck, etc.) ❑ RESIDENTIAL ACCESSORY STRUCTURE (Garage, shed, deck, etc.) ❑ MECHANICAL SYSTEM/APPLIANCE REPAIR or REPLACEMENT ❑ PLUMBING SYSTEM/APPLIANCE REPAIR or REPLACMENT ❑ ELECTRICAL SYSTEM/APPLIANCE REPAIR or REPLACEMENT OTHER (Describe) �I� i 4, ar ; -- Z II (For''ALL projects, please provide a detailed descFiption of work to be performtd, including current use of areas, proposed uses, square footage, existing condition and proposed new condition, appliance size and efficiency, type and amount of materials to be used, etc.) -/'-0II �� f C _ r c Sq. Ft./LF Amps Btu's Squares Gallons Other Project Value: (Contract value or the cost of all materials and labor included in the entire project) $ (�(� OWNER/CONTRACTOR SIGNATURE OF UNDERSTANDING AND AGREEMENT I hereby certify that the setback distances proposed by this permit application are accurate and do not violate applicable ordinances, rules or regulations of the City of Wheat Ridge or covenants, easements or restrictions of record; that all measurements shown and allegations made are accurate; that I have read and agree to abide by all conditions printed on this application and that I assume full responsibility for compliance with applicable City of Wheat Ridge codes and ordinances for work under any permit issued based on this application; that I am the legal owner or have been authorized by the legal owner of the property to perform the described work and am also authorized by the legal owner of any entity included on this application to list that entity on this application. I, the applicant for this building permit application, warrant the truthfulness of the information provided on the application. CIRCLE ONE: (OWNER) CONTRACTOR) r (AUT D REPRESENTATIVE) of (OWNER) (CONTRACTOR) Sianature (first and last na DATE: DEPARTMENT USE ONLY ZONING COMMMENTS: OCCUPANCY CLASSIFICATION: Reviewer: BUILDING DEPARTMENT COMMENTS: Reviewer: Building Division Valuation: $ i CITY OF WHEAT RIDGE Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: 323 It" 11 Sc Job Address: 1 1 4(5 W . 'r_- 70 Permit Number: 2G1.�S0.��l0 ❑ No one available for inspection: Ti Re -Inspection required: Yes No When corrections have been made, callforr -inspection at 303-234-5933 Date:_ 3 �� J �� Inspeeto�: ----�. DO NOT RENIO-VE``TH/S NOTICE O ro r a N m o W x H a mry w R Fd �O n H pJ m m B m ". n W. 1w 0 H M O 0 mp b 13 ryH H- r £ r pK(D 7 C7 7HS pM �$. Wr6 O H K n O nm r� r y E °p m a m n N CT O r r ro M ,(y 4 a (A 0 y m T n o O n v # m w r �l n r 0 m z ° n n n l0 O N o x n a m n n o N OD ~' ro H W N m n n 0cr M„ m rr a F'- (D O ' C! m�7 m a w " a "' o � O11-J '0U" K C7 z m w ° '•"1• F. re O m 0 x n a a °' m m m y O 5 a y y o n u�i z� nLO m� O (D pl [n r r "a d 0 p rt$ tt z p r• n N O !++ m m p l0 3 O H w � p M 0:) p � 14 O o R w n b o O `/^• O p W H (D W H M �T n m m a m LA) f,. Q m m a 1 K Hrr W N O ro C O W� N 91 O DI n r z m r 'o" n O O 0 N CJ M "m a m F,rr M n O 0 n �- w a w c C] r a a �. a a m a "• V r- O D w W K E 0 N o �- a a F- m° w t o rr p w a a ti b d Q1 O m (t rr f°r r�• (D m m •• H m h O z v, o w 91 N m n N " a O m m m a a N O a m (D 00 Yo o ° o N 't7 ° 03 n H rr mM H o-°i z m C, m b" m (D Fj H n rt m s K ° rNi Y o K n Fl- It n o rW�:" b o rr (] d. � o m r o o tl a w ] S r M ~ rh W z L' N y a O �O r ro o m 3 E o m m N n r H m P n m (� r v- rr O o a b rt w~ EO w R b p O y p m z a M� n p N m � n °• ^ lD m ( o z rr a n W O �• r •i � � a^ ro M N rfi 'C1 0) N. n ro m x 0 O O rn n a n F i to (� rt r- tr• O m m ro in m a r x a r- m ID ti w a a p W o ff° w H w m �' ror N n z £ o a rn 0 Cr a * 3 p m m rt w "m c" °a H 3 n rr p W K a y o u :dUl Z f1 a s 0L Q b m H O ID CD (D n W N• m o n o a '� 0 N. (D a v# n R LT1 l v ��J gi x m m lD O O O N• O n mo M a r 0 y LQ p~ H r W n m O x —Z 'J �q m m w a w° b O L O F• a [ H� O LQ m a m w io M am m l! 1 C] m H w ° d b N ^ CD m H.a rr 0 F. n z n C ro O \ 1 n K n O 0 0 ? `o G n �- r) r o a a ci �a L ts a M fD IQ N o a k o P- a ° P. w o rr O w " C7 O w 11 Pi m ft rt rt 8 fD m m a a n m ry O m o N z m a a o 10 rl n m n N -- a O r ~ IV m NO a m e a aa 00 AP— 4-- 1 1,c4 C"', �,I City of W heat �ge BUSINESS LICENSE INSPECTION PERMIT NO. 201702952 INSPECTION DAY/TIME Western Center for the Conservation of Fine Arts -2� wowBUSINESS NAME: ADDRESS: 11415 W 1-70 Frontage Road North CONTACT NAME: Nancy Jurbala 30o0 SQ FT 13 OCCUPANCY TYPE -3 O OCCUPANCY LOAD SPRINKLERED NOWSPRINKLERED Inspector Signature i CITY OF WHEAT RIDGE Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: Z�> 1--7-- v s, .ze L F s Job Address: l i 9 I S- W --3-- io Permit Number: '3 o /-7 o -7L4 ) -6 Llfio s2- {'-f_ (9C� /oad = t-/ 1�L_-z 'ARJIhPn�rc� ❑ No one available for inspection: Time 9z 3 gM��M Re -Inspection required: Yes No When corrections have been made, call for re -inspection at 303-234-5933 Date: -_3 i Z, 4 S Inspector: e DO NOT REMOVE THIS NOTICE i CITY OF WHEAT:RIDGE Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: _ v s Job Address: 114f i s w Permit Number: -C-? o) 7 D S d 30 0 o sa -F`�- occ load= f3 �Z A�t�ro vP ❑ No one available for inspection: Time = -/ /PM Re -Inspection required: Yes When corrections have been made, call for re -inspection at 303-234- Date:-;P 03-234-Date:a 1 & Inspector: -T-b DO NOT REMOVE THIS NOTICE INSPECTION RECORD Inspection online form: http://www.ci.wheatridge.co.us/inspection Cancellations must be submitted via the online form before 8 a.m. the day of the inspection Inspections will not be performed unless this card is posted on the project site Request an inspection before MIDNIGHT (11:59 PM) to receive an inspection the following business day PERMIT:` I DO ADDRESS: II�iI� ;��'i� JOB CODE:{,/w Foundation Inspections Date Inspector Initials Comments 102 Caissons / Piers 103 Footing / P.E. Letter 104 Foundation Setback Cert. 105 Stem Walls 106 Foundation wall Insulation Do Not Pour Concrete Prior To Approval Of The Above Inspections Underground / Slab Inspections Date Inspector Initials Comments 201 Electrical / Cable/ Conduit 202 Sewer Underground Int. 203 Sewer Underground Ext. 204 Plumbing Underground Int. 205 Plumbing Underground Ext. 200 ;Nater Unjergcound Do Not Cover Underground or Below / In -Slab Work Prior To Approval Of The Above Inspections Rough Inspection Date Inspector Initials Comments 301 Rough Framing 302 Wall Sheathing 303 Roof Sheathing 304 Sheer Inspection 305 Insulation 306 Mid -Roof 307 Metal / Lath / Stucco 308 Rough Electrical Residential 309 Rough Electrical Commercial p� { 310 Electrical Meter Residential 311 Electrical Meter Commercial 312 Temp. Const. Meter 313 Rough Plumbing Residential 314 Rough Plumbing Commercial 315 Shower Pan SEE OVER FOR ADDITIONAL INSPECTIONS PERMIT:uI ADDRESS: I 'IC � I" �Ehkll JOB CODE:"<211cl, _ . Rough Inspection (continued) Date Inspector Initials Comments 316 Rough Mechanical Residential 317 Rough Mechanical Commercial 318 Boiler / Furnace 319 Hot water tank 320 Drywall screw and Nail 321 Moisture board / shower walls 322 Rough Grading 323 Miscellaneous Final Inspections Date Inspector Initials Comments 402 Gas Meter Release 403 Final Electrical Residential 404 Final Electrical Commercial 405 Final Mechanical Residential 406 Final Mechanical Commercial 407 Final Plumbing Residential 408 Final Plumbing Commercial 409 Final Roof 410 Final Window/Door 411 Landscape/Park/Planning* Inspections from these entities shall be requested one week in advance. landscaping and parking inspections please �al l 303-235-2846 **For ROW and drainage inspections please call 303-235-2861 ***For fire inspections please contact the Fire Protection District for your project. 412 Row/Drainage/Public Works** 413 Flood plain Inspection** ;*For 414 Fire Insp. / Fire Protection*** 415 Public Works Final** 416 Storm Water Mgmt.** 417 Zoning Final Inspection* 418 Building Final Inspection: Note: All items must be completed and approved by Planning, Public Works, Fire and Building before a Certificate of Occupancy is issued. Approval of the Final Building Inspection does not constitute authorization of occupancy. For Low Voltage permits please be sure that rough inspections are completed by the Fire District and Electrical low voltage by the Building Division. i CITY OF WHEAT RIDGE Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: /hi F -r- Job Address: %V Permit Number: 0176F'620 ❑ No one available for inspection.: Time -' AM/PMr,l g Re -Inspection required: Yes (+ No When corrections have been made, call for re -inspection at 303-234-5933 Date: � '�� Inspector: A/ 4— DO NOT REMOVE THIS NOTICE i CITY OF WHEAT RIDGE Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: /48 Job Address: �� Jr W E %v Permit Number: G L)®c No one available for insption: Time 'rAllll%PM Re -Inspection required: Yes No When corrections have been made, call for re -inspection at 303-234-5933 Date:.-) • / /-/ - M/_ Inspector: 3a, U 6,')b r4- DO i)br4- DO NOT REMOVE THIS NOTICE A i CITY OF WHEAT RIDGE Building Inspection Division -- (303)x234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax 1 e --z, �-, V,� r( INSPECTION NOTICE Inspection Type: &L- t Job Address: L0 T-']�r,-�-t9 I ��Q Permit Number: C) !Z, 0 9 S �- 4nit v .'� SL� ❑ No one available for inspection: Time)h (% &/PM Re -Inspection required: Yes No When corrections have been made, call for re -inspection at 303-234-5933 Date:c �/ Inspecto DO NOT REMOVE THIS NOTICE CITY OF WHEAT RIDGE Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office - (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: Is F X, Job Address: ) i ti i IT w 'f- ? e Aj Permit Number: 01--�-(3a L. ❑ No one available for inspection: Time 10 1 ,/PM / ~-__11 Re -Inspection required: Yes No' *When corrections have been made, call for re -inspection at 303-234-5933 f `� Date'.Q Inspector: )fes; * ; DO NOT REMOVE THIS NOTICE' City of Wheat Ridge ' Commercial Electric PERMIT - 201800284 PERMIT NO: 201800284 ISSUED: 01/29/2018 JOB ADDRESS: 11415 W I-70 Frontage RD N EXPIRES: 01/29/2019 JOB DESCRIPTION: Install 1 new fire alarm control panel & 1 RF central station communicator (AES -7707) 2 manual pull box, 9 smoke detectors & 1 heat detector; 3 horn/strobes and 3 strobes; 3,380 sq ft total *** CONTACTS *** OWNER (303)423-9700 SIX OAK LIMITED PARTNERSHIP SUB 303-444-1191 Robert Bonifas 170005 Alarm Detection System, Inc *** PARCEL INFO *** ZONE CODE: UA / Unassigned USE: UA / Unassigned SUBDIVISION CODE: 420 / Storage Warehouse; 0 BLOCK/LOT#: 0 / *** FEE SUMMARY *** ESTIMATED PROJECT VALUATION: 4,800.00 FEES Total Valuation 0.00 Use Tax 100.80 Permit Fee 125.05 ** TOTAL ** 225.85 *** COMMENTS *** *** CONDITIONS *** Work must comply with the 2014 NEC, 2012 IBC and other applicable codes and ordinances. Work is ubject to field inspection. 1, by my signature, do hereby attest that the work to be performed shall comply with all accompanying approved plans and specifications, applicable wilding codes, and all applicable municipal codes, policies and procedures, and that I am tie legal owner or have been authorized by the legal owner of the property and am authorized to obtain this permit and perform the work described and approved in conjunction with this_permit. I further attest that I am legally authorized to include all entities named within this document as parties to the work to be performed and that all work to /eribrmed is disclosed in this document and/or its' accompanying approved plans and specifications. Signature of OWNER or CONTRACTOR (Circle one) Date I. This permit was issued based on the information provided in the permit application and accompanying plans and specifications and is subject to the compliance with those documents, and all applicable statutes, ordinances, regulations, policies and procedures. 2. This permit shall expire 365 days after the date of issuance regardless of activity. Requests for extension must be made in writing and received prior to the date of expiration. An extension of no more than 180 days made be granted at the discretion of the Chief Building Official and may be subject to a fee equal to one-half of the original permit fee. 3. If this permit expires, a new permit may be required to be obtained. Issuance of a new permit shall be subject to the standard requirements, fees and procedures for approval of any new permit. Re -issuance or extension of expired permits is at the sole discretion of the Chief Building Official and is not guaranteed. 4. No work of any manner shall be performed that shall results in a change. of the natural flow of water without prior and specific approval. 5. The permit holder shall notify the Building and Inspection Services Division in accordance with established policy of all required inspections and shall not proceed or conceal work without written approval of such work from the Building and Inspection Services Division. g. The issuance or granting of a prmit shall not be construed to be a permit for, or an approval of, an violation of any provision of any applicable code or any ordinaiqe or regulation of this jurisdiction. Approval of work is subject to field inspection. Signature of Chief Building Offici'l Date REQUESTS MUST BE MADE BY 11:59PM ANY BUSINESS DAY FOR INSPECTION THE FOLLOWING BUSINESS DAY. City of Wheat jddge COMMUNITY DEVELOPMENT Building & Inspection Services Division 7500 W. 2911 Ave., Wheat Ridge, CO 80033 Office: 303-235-2855 * Fax: 303-237-8929 Inspection Line: 303-234-5933 Email: permits(@ci.wheatridge.co.us FOR OFFICE USE ONLY Date: �( Plan/Permit # Plan Review Fee: Building Permit Application *** Please complete all highlighted areas on both sides of this form. Incomplete applications may not be processed. "** Property Owner Email: Mailing Address: (if different than property address) Address: Citv, State, Zip: Architect/Engineer E-mail: I /,I 12%n��' % 1Phone: ^%Zd'Qq 7— 1g LO 3 Contractor: J Contractors City License #: _ II�Q� Phone:y" Contractor E-mail Address: �� (,��r}�rr► C" UM For Plan Review Questions & Comments (please print): [ 1 CONTACT NAME (please print): ��SS I�1'�,%1(SP� Phone: -' , `J• -T ��` ; - Sub Contractors: Electrical: W.R. City License # Other City Licensed Sub: City License # City License # Plumbing: W.R. City License # Other City Licensed Sub: Mechanical: W.R. City License # Complete all information on BOTH sides of this form COMMERCIAL ❑ RESIDENTIAL Description of work: (Check all that apply) ❑ NEW COMMERCIAL STRUCTURE ❑ ELECTRICAL SERVICE UPGRADE ❑ NEW RESIDENTIAL STRUCTURE ❑ COMMERCIAL ROOFING ❑ COMMERCIAL ADDITION ❑ RESIDENTIAL ROOFING ❑ RESDENTIAL ADDITION ❑ WINDOW REPLACEMENT ❑ COMMERCIAL ACCESSORY STRUCTURE (Garage, shed, deck, etc.) ❑ RESIDENTIAL ACCESSORY STRUCTURE (Garage, shed, deck, etc.) ❑ MECHANICAL SYSTEM/APPLIANCE REPAIR or REPLACEMENT ❑ PLUMBING SYSTEM/APPLIANCE REPAIR or REPLACMENT ❑ ELECTRICAL SYSTEM/APPLIANCE REPAIR or R7PLACEMENT OTHER (Describe) TJ T:n-t (For -A& projects, please provide a detailed description of work to be performed, including current use of areas, proposed uses, square footage, existing condition and proposed new condition, appliance size and efficiency, type and amount of materials to be used, etc.) ns�l t 1 V1�,v�-�ir� �►mn �4n t ret mal 1 04 Mj o rs I w6+ dk,-ltovr. 3 horn ( *00e �Y Sq. FULF ) Btu's Gallons Amps Squares Other Project Value: (Contract value or the cost of all materials and labor included in the entire project) OWNER/CONTRACTOR SIGNATURE OF UNDERSTANDING AND AGREEMENT I hereby certify that the setback distances proposed by this permit application are accurate and do not violate applicable ordinances, rules or regulations of the City of Wheat Ridge or covenants, easements or restrictions of record; that all measurements shown and allegations made are accurate; that I have read and agree to abide by all conditions printed on this application and that I assume full responsibility for compliance with applicable City of Wheat Ridge codes and ordinances for work under any permit issued based on this application; that 1 am the legal owner or have been authorized by the legal owner of the property to perform the described work and am also authorized by the legal owner of any entity included on this application to list that entity on this application. I, the applicant for this building permit application, warrant the truthfulness of the information provided on the application. CIRCLE ONE: (OWN ) (CONTRACTO or (AUTHORIZED REPRESENTATIVE) of (OWNER) (CONTRACTOR) Signature (first and last name): DATE: ZONING COMMMENTS: Reviewer: BUILDING DEPARTMENT COMMENTS: Reviewer: DEPARTMENT USE ONLY OCCUPANCY CLASSIFICATION: Building Division Valuation: $ SAFE SYSTEMS RE - 421 S. PIERCE AVE LOUISVILLE, CO 80027 303-444-1191 BURGLARY•FIRE*ACCEss C01Moc PROJECT: FA -7726 01/18/2018 WCCFA 11415 WEST 1-70 FRONTAGE RD NORTH WHEAT RIDGE, CO 80033 ENCLOSURES Avigoony NFW-50 7707 NOT-BG12LX NP -100 NH -100 NMM-100 SYSTEM SENSOR HORN/STROBE BK-PC2WL BK-SCWL REVISION: NOI DATE I BY: IDESCRIPTION 1 101/18/181 MK I PERMIT SET Max` SHOP DRAWING BY: MAX KARGARZADEH, SET NICET IV - FIRE ALARM CERT 101856; EXP. NOV. 1, 2018 299 MILWAUKEE ST. SUITE 222 DENVER, COLORADO 720-297-1563 cad80113@hotmail.com FireWarden-50(E) Intelligent Addressable FACP DN -7102:E 0 NOTIFIER° with Built -In Communicator by Honeywell Addressable Fire Alarm Control Panels; General The NOTIFIER FireWarden-50 (NFW-50) is a Fire Alarm Con- trol Panel (FACP) and Digital Alarm Comm un icato r/Transm itter (DACT) combined into one circuit board. This compact, intelli- gent addressable control panel supports up to 50 addressable devices in any combination of detectors or modules. With an extensive list of powerful features, the FireWarden-50 pro- grams just like FireWarden-100 products, yet fits into applica- tions previously served only by conventional panels. The FireWarden-50's integral DACT transmits system status (alarms, troubles, AC loss, etc.) to a Central Station via the public switched telephone network. It also allows remote and local programming of the control panel using the PS -Tools Upload/Download utility. In addition, the control panel may be programmed or interrogated off-site via the public switched telephone network. Any personal computer with Windows'" 95 or greater, and compatible modem with a speed of 14.4 kbps or faster and Upload/Download software, may serve as a Ser- vice Terminal. This allows download of the entire program or upload of the entire program, history file, walk -test data, cur- rent status and system voltages. The power supply and all electronics are contained on a single circuit board supported on a new quick install chassis and housed in a metal cabinet. Available accessories include local and remote upload/download software, remote annunciators, and reverse polarity/city box transmitter. (4XTM) The FireWatch Series internet monitoring modules IPDACT-2 and IPDACT-2UD permit monitoring of alarm signals over the Internet, saving the monthly cost of two telephone lines. Although not required, the secondary telephone line may be retained providing backup communication over the public switched telephone line. NOTE: Unless otherwise specified, the term FireWarden-50 is used in this data sheet to refer to both the FireWarden-50 and the FireWarden-50E FACPs. For FireWarden-50C, refer to DN - 60446. Features • Listed to UL Standard 864, 9th edition. • Auto -program (learn mode) reduces installation time. Reports two devices set to the same address. • On -board DACT. • Two independently programmable Style Z (Class A) or Style Y (Class B) NAC circuits. • Selectable strobe synchronization for System Sensor, Wheelock, and Gentex devices. • Remote Acknowledge, Silence, Reset and Drill via address- able monitor modules. • Two programmable relays and one fixed trouble relay. • Built-in Programmer. • Telephone Line Active LEDs. • EIA -232 PC interface. • Integral 80 -character LCD display with backlighting. • Real-time clock/calendar with automatic daylight savings control. • History file with 500 event capacity. • Automatic detector sensitivity testing (NFPA 72 compliant). • Automatic device type -code verification. • Point trouble identification. • Waterflow selection per module point. • Alarm verification selection per detector point. • Maintenance alert warns when smoke detector dust accu- mulation is excessive. • One-person audible or silent walk test with walk -test log and printout. • System alarm verification selection per detector point. • PAS (Positive Alarm Sequence) and Pre -signal per point (NFPA 72 compliant). • Up to eight ANN -BUS annunciators • Remote Acknowledge, Alarm Silence, Reset and Drill via addressable modules or remote annunciator. • Upload/Download (local or remote) of program and data via integral DACT. SLC COMMUNICATION LOOP • Single addressable SLC loop which meets NFPA Style 4, 6 and 7 requirements. • 50 addressable device capacity (any combination of addressable detectors and modules). • Compatible with NOTIFIER FireWarden addressable devices (refer to the FireWarden SLC Wiring Manua/). NOTIFICATION APPLIANCE CIRCUITS (NACS) • Two independently programmable output circuits. Circuits can be configured for the following outputs: — Style Y (Class B) — Style Z (Class A) — Door Holder Service (cannot be used for notification appliances) — Aux Power Source (cannot be used for notification appliances) • Silence Inhibit and Autosilence timer options. • Continuous, March Time, Temporal or California code for main circuit board NACs with two-stage capability. • Selectable strobe synchronization per NAC. • 2.5 A total power for NACS. NOTE: Maximum or total 24VDC system power shared between all NAC circuits and the ANN -BUS is 2.7 A. DN -7102:E • 02/22/2011 — Page 1 of 4 NFW-50 Fire Alarm Control Panel n J J NP -100 Photo Detector NI -100 Ionization Detector .:r NH -100 Series Heat Detector NDM-100 Dual Monitor Module NP -100T, NP -A100 Photo/Thermal NMM-100 Monitor Module NZM-100 2 -Wire Detector Monitor Module DNR Duct Detector NOT-BG12LX Addressable Manual Pull Station LED INDICATORS N -ANN -10 Graphic LED • AC Power (green) Module • Fire Alarm (red) • Supervisory (yellow) N -ANN -LED • Trouble (yellow) • Alarm Silenced signals (yellow) PROGRAMMING AND SOFTWARE N-ANN-RLY • Autoprogram (learn mode) reduces installation time. Relay Module • Custom English labels (per point) may be manually entered or selected from an internal library file. r__N• • Two programmable Form -C relay outputs. FCPS-2456 • 20 software zones. FCPS-24S8 • Continuous fire protection during online programming at the front panel. _ • Program Check automatically catches common errors not NZM-100-6, linked to any zone or input point. NMM-100-10 • OFFLINE PROGRAMMING: Create the entire program in N -ANN -80 your office using PS -Tools, Windows® -based software Interface Module package, and upload/download system programming locally. PS -Tools is available on www.magni-fire.com. N-ANN-S/PG Printer Gateway User interface LED INDICATORS N -ANN -10 Graphic LED • AC Power (green) Module • Fire Alarm (red) • Supervisory (yellow) N -ANN -LED • Trouble (yellow) • Alarm Silenced signals (yellow) ADDRESSABLE FIRE ALARM CONTROL PANEL Page 2 of 4 — DN -7102:E • 02/22/2011 Product Line Information NFW-50: Combination DACT/Fire Alarm Control Panel with one SLC loop. Includes main circuit board with display, chassis with transformer, backbox with door, plastic bag containing screws, cables, key, etc., manual. (For NFW-50C, refer to DN - 60446.) NFW-50E: Same as NFW-50, but operates at 240 VAC. NFW-50R: Same as NFW-50, with red backbox and door. DP-5105OB: Optional dress panel for NFW-50 (black). DP -51050: Optional dress panel for the NFW-50R (red). TR -CE -B: Optional trim ring for semi -flush mounting. (Black. For red, order TR -CE.) BB -XP: Optional cabinet for one or two modules. BB -25: Optional cabinet for up to six modules mounted on CHS -6 chassis. BB -26: Battery backbox, holds up to two 25 AH batteries and CHG-75. NFS-LBB: Battery box, houses two 55 AH batteries CHS -6: Chassis, mounts up to six multi -modules in a BB -25 cabinet. CHG-75: Battery charger for lead -acid batteries with a rating of 25 to 75 AH. CHG-120: Remote battery charging system for lead -acid bat- teries with a rating of 55 to 120 AH. Requires additional NFS- LBB for mounting. NOTE: CHG-120 or CHG-75 required for batteries larger than 18AH. BAT Series: Batteries, see data sheet DN -6933. KEYPAD N-ANN-RLY • 16 key alpha -numeric pad Relay Module • Acknowledge/Step • Alarm Silenced • Drill (Manual Evacuate) r__N• Reset (lamp test) ADDRESSABLE FIRE ALARM CONTROL PANEL Page 2 of 4 — DN -7102:E • 02/22/2011 Product Line Information NFW-50: Combination DACT/Fire Alarm Control Panel with one SLC loop. Includes main circuit board with display, chassis with transformer, backbox with door, plastic bag containing screws, cables, key, etc., manual. (For NFW-50C, refer to DN - 60446.) NFW-50E: Same as NFW-50, but operates at 240 VAC. NFW-50R: Same as NFW-50, with red backbox and door. DP-5105OB: Optional dress panel for NFW-50 (black). DP -51050: Optional dress panel for the NFW-50R (red). TR -CE -B: Optional trim ring for semi -flush mounting. (Black. For red, order TR -CE.) BB -XP: Optional cabinet for one or two modules. BB -25: Optional cabinet for up to six modules mounted on CHS -6 chassis. BB -26: Battery backbox, holds up to two 25 AH batteries and CHG-75. NFS-LBB: Battery box, houses two 55 AH batteries CHS -6: Chassis, mounts up to six multi -modules in a BB -25 cabinet. CHG-75: Battery charger for lead -acid batteries with a rating of 25 to 75 AH. CHG-120: Remote battery charging system for lead -acid bat- teries with a rating of 55 to 120 AH. Requires additional NFS- LBB for mounting. NOTE: CHG-120 or CHG-75 required for batteries larger than 18AH. BAT Series: Batteries, see data sheet DN -6933. P2R Strobe —a a P2R Strobe Power Supply FCPS-2456 FCPS-24S8 is, P2R _ Strobe NZM-100-6, NMM-100-10 Multiple -Circuit Interface Module ADDRESSABLE FIRE ALARM CONTROL PANEL Page 2 of 4 — DN -7102:E • 02/22/2011 Product Line Information NFW-50: Combination DACT/Fire Alarm Control Panel with one SLC loop. Includes main circuit board with display, chassis with transformer, backbox with door, plastic bag containing screws, cables, key, etc., manual. (For NFW-50C, refer to DN - 60446.) NFW-50E: Same as NFW-50, but operates at 240 VAC. NFW-50R: Same as NFW-50, with red backbox and door. DP-5105OB: Optional dress panel for NFW-50 (black). DP -51050: Optional dress panel for the NFW-50R (red). TR -CE -B: Optional trim ring for semi -flush mounting. (Black. For red, order TR -CE.) BB -XP: Optional cabinet for one or two modules. BB -25: Optional cabinet for up to six modules mounted on CHS -6 chassis. BB -26: Battery backbox, holds up to two 25 AH batteries and CHG-75. NFS-LBB: Battery box, houses two 55 AH batteries CHS -6: Chassis, mounts up to six multi -modules in a BB -25 cabinet. CHG-75: Battery charger for lead -acid batteries with a rating of 25 to 75 AH. CHG-120: Remote battery charging system for lead -acid bat- teries with a rating of 55 to 120 AH. Requires additional NFS- LBB for mounting. NOTE: CHG-120 or CHG-75 required for batteries larger than 18AH. BAT Series: Batteries, see data sheet DN -6933. PRT/PK-CABLE: Cable printer/personal computer interface cable. PRN -6: UL listed compatible event printer. Uses tractor -fed paper. IPDACT, IPDACT2/2UD Internet Monitoring Module: Mounts in bottom of enclosure with optional mounting kit (PN IPBRKT). Connects to primary and secondary DACT tele- phone output ports for internet communications over customer provided ethernet internet connection. Requires compatible Teldat Visoralarm Central Station Receiver. Can use DHCP or static I P. (See data sheet do -60408 for more information.) IPBRKT: Mounting kit for IPDACT-2/2UD in common enclosure. IPSPLT: Y -adaptor option allows connection of both panel dialer outputs to one IPDACT-2/2UD cable input. AC-TRMBLK: AC Terminal Block mounts to a metal bracket, in turn, mounts to the FACP chassis. Use AC-TRMBLK when wire nuts are not allowed for AC connections to the trans- former. OPTIONAL MODULES 4XTM Reverse Polarity Transmitter Module: Provides a supervised output for local energy municipal box transmitter, alarm and trouble. Includes a disable switch and disable trou- ble LED. ANN -SEC: Optional secondary ANN -BUS interface module. Note: Used only with firmware 3.0 or higher. COMPATIBLE ANNUNCIATORS N -ANN -80(-W): Remote LCD annunciator mimics the informa- tion displayed on the FACP LCD display. Recommended wire type is un -shielded. (Basic model is black; order -W for white; see DN -7114.) N -ANN -1/0: LED Driver Module provides connections to a user supplied graphic annunciator. (See DN -7105.) N -ANN -LED: Annunciator Module provides three LEDs for each zone: Alarm, Trouble, and Supervisory. Ships with red enclosure. (See DN -60242.) N -ANN -BLED: Provides alarm (red) indicators for up to 30 input zones or addressable points. (See DN -60242.) N-ANN-RLY: Relay Module provides 10 programmable Form - C relays. Can be mounted inside the cabinet. (See DN -7107.) N-ANN-S/PG: Serial/Parallel Printer Gateway module pro- vides a connection for a serial or parallel printer. (See DN - 7103.) ADDRESSABLE DEVICES All feature a polling LED and rotary switches for addressing. NI -100: Addressable low -profile ionization smoke detector. NP -100: Addressable low -profile photoelectric smoke detector. NP-10OT: Addressable low -profile photoelectric smoke detec- tor with thermal sensor. NP-10OR: Remote test capable addressable photoelectric smoke detector for use with DNR(W) duct detector housing. NH -100: Fast -response, low -profile heat detector. NH-10OR: Fast -response, low -profile heat detector with rate - of -rise option. NH-10OH: Fast -response, low -profile heat detector that acti- vates at 190°F/88°C. NP -A100: Addressable low -profile multi -sensor detector. DNR: InnovairFlex low -flow non -relay duct -detector housing. (Order NP-10OR separately.) DNRW: InnovairFlex low -flow non -relay duct -detector housing, with NEMA -4 rating. Watertight. (Order NP-10OR separately.) NMM-100: Addressable Monitor Module for one zone of nor- mally -open dry -contact initiating devices. Mounts in standard 4.0" (10.16 cm.) box. Includes plastic cover plate and end -of - line resistor. Module may be configured for either a Style B (Class B) or Style D (Class A) IDC. NDM-100: Dual Monitor Module. Same as NMM-100 except it provides two Style B (Class B) only IDCs. NMM-10OP: Miniature version of NMM-100. Excludes LED and Style D option. Connects with wire pigtails. May mount in device backbox. NZM-100A: Similar to NMM-100A. Addressable Monitor Mod- ule for one zone of conventional two -wire detectors. Requires resettable 24 VDC power. Refer to the Device Compatibility Document for listed compatible devices and quantity limita- tion. NZM-100-6: Six -zone interface module. Mount one or two modules in a BB -XP cabinet (optional). Mount up to six mod- ules on a CHS -6 chassis in a BB -25 cabinet. NMM-100-10: Ten -input monitor module. Mount one or two modules in a BB -2 cabinet (optional). Mount up to six modules on a CHS -6 chassis in a BB -25 cabinet. NC -100: Addressable Control Module for one Style Y/Z (Class B/A) zone of supervised polarized Notification Appliances. Mounts directly to a 4.0" (10.16 cm.) electrical box. Notification Appliance Circuit option requires external 24 VDC to power notification appliances. NC-10OR: Addressable relay module containing two isolated sets of Form -C contacts, which operate as a DPDT switch. Mounts directly to a 4.0" (10.16 cm.) box, surface mount using the SMB500. NOT BG12LX: Addressable manual pull station with interface module mounted inside. N100 -ISO: Fault Isolator Module. SMB500: Used to mount all modules except the NMM-100P. NOTE: For more information on Compatible Addressable Devices for use with the FireWarden-50, see the following data sheets (document numbers): N1004SO (DN -6994), NP -100 series (DN - 6995), NI -100 (DN -6996), NH-100/NH-10OR (DN -6997), DNR/ InnovairFlex (DN -60424, DN -60429), NP -A100 (DN -6998), NMM- 100/NMM-I00P/NDM-100/NZM-100 (DN -6999), NC -100 (DN - 7000), NC -100R (DN -60383), NMM-100-10 (DN -6990), and NOT - BG 12LX (DN -7001). ADDRESSABLE DEVICE ACCESSORIES End -of -Line Resistor Assembly (R -47K and R -3.91K): The 47k ohm assembly supervises the NMM-100-10, NDM-100, NMM-100P, and NC -100 module circuits. The 3.9k ohm assembly supervises the NZM-100-6 module circuit. These resistors are included with each module. Power Supervision Relay: Supervises the power to 4 -wire smoke detectors and notification appliances. Wiring Requirements While shielded wire is not required, it is recommended that all SLC wiring be twisted -pair to minimize the effects of electrical interference. Refer to the panel manual for wiring details. DN -7102:E • 02/22/2011 —Page 3 of 4 SYSTEM SPECIFICATIONS System Capacity • Intelligent Signalling Line Circuits.......................................1 • Addressable device capacity............................................50 • Programmable software zones.........................................20 • Annunciators......................................................................8 Electrical Specifications AC Power: FireWarden-50: 120 VAC, 60 Hz, 3.0 A. FireWar- den-50E: 240 VAC, 50 Hz, 1.5 A. Wire size: minimum 14 AWG (2.00 mm2) with 600 V insulation. Nonpower -limited, super- vised. Battery: Two 12 V 18 AH lead -acid batteries. Battery Charger Capacity: 7-18 AH (FireWarden-50 cabinet holds maximum of two 18 AH batteries.) Communication Loop: Supervised and power -limited. Notification Appliance Circuits: Terminal Block provides connections for two NACs, Style Y (Class B) or Style Z (Class A). Special Application power. Power -limited, supervised cir- cuitry. Maximum signaling current per circuit: 2.5 A. End -of - Line Resistor: 4.7k ohm, 112 watt (P/N 71252 UL listed) for Style Y (Class B) NAC. Refer to the NOTIFIER Device Compatibility Document for listed compatible devices. Two Programmable Relays and One Fixed Trouble Relay: Contact rating: 2.0 A @ 30 VDC (resistive), 0.5 A @ 30 VAC (resistive). Form -C relays, nonpower -limited, nonsupervised. Cabinet Specifications Door: 19.26" (48.92 cm.) high x 16.82" (42.73 cm.) wide x 0.72" (1.82 cm.) deep. Backbox: 19.00" (48.26 cm.) high x 16.65" (42.29 cm.) wide x 5.25" (13.34 cm.) deep. Trim Ring (TR-CE/B): 22.00" (55.88 cm.) high x 19.65" (49.91 cm.) wide. Shipping Specifications Weight: 26.9 lbs. (12.20 kg.) Dimensions: 20.00" (50.80 cm.) high x 22.5" (57.15 cm.) wide x 8.5" (21.59 cm.) deep. Temperature and Humidity Ranges This system meets NFPA requirements for operation at 0 — 49°C/32 — 120°F and at a relative humidity 93% ± 2% RH (noncondensing) at 32°C ± 2°C (90°F t 3°F). However, the useful life of the system's standby batteries and the electronic components may be adversely affected by extreme tempera- ture ranges and humidity. Therefore, it is recommended that this system and its peripherals be installed in an environment with a normal room temperature of 15 — 27°C/60 — 80°F. NFPA Standards The FireWarden-50 complies with the following NFPA 72 Fire Alarm Systems requirements: — LOCAL (Automatic, Manual, Waterflow and Sprinkler Supervisory). — AUXILIARY (Automatic, Manual and Waterflow) (requires 4XTM). — REMOTE STATION (Automatic, Manual and Waterflow) (Where a DACT is not accepted, the alarm, trouble and supervisory relays may be connected to UL 864 listed transmitters. For reverse polarity signaling of alarm and trouble, 4XTM is required.) — PROPRIETARY (Automatic, Manual and Waterflow). —CENTRAL STATION (Automatic, Manual and Waterflow, and Sprinkler Supervised). — OT, PSDN (Other Technologies, Packet -switched Data Network) Agency Listings and Approvals The listings and approvals below apply to the basic FireWar- den-50 control panel. In some cases, certain modules may not be listed by certain approval agencies, or listing may be in pro- cess. Consult factory for latest listing status. • UL: S635 • FM approved • CSFM: 7165-0028:239 • MEA: 442-06-E Vol. 2 NOTE: See DN -60446 for ULC -listed model. NOTIFIER®, FireWarden@ and System Sensor® are registered trademarks of Honeywell International Inc. Microsoft® and Windows® are registered trademarks of the Microsoft Corporation. 02011 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited. 1S0 �oo� This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. ENGINEERING &MANUFACTURING QUALITY SYSTEMS All specifications are subject to change without notice. Made in the U.S. A. For more information, contact Notifier. Phone: (203) 484-7161, FAX (203) 484-7118. www.notifier.com Page 4 of 4 — DN -7102:E • 02/22/2011 System Current Draw - NFW-50 Current Draw 1 '® �,.,t �0.123 A 10.600 Device P,im,,yNon-Alarm-C1 �w C1 -Primary Non -Alarm qty D� Total C2 Qty s� -Prim ary Al Draw Primary Alarm - C2 a rm C3 -Secondary Non -Alarm Total Qty Draw I Total Main Circuit , Boaoe■�t�oe■�K-T e ne�■�oe�■�nee�■� oe■■�oe■■�oee■� - K.T. oe■�oe■ �oeeTOR■I •. ME3 ne Knee � oe■�ne■��neeWM-I� DD NoAppliance: a eee Knne ..Notification....nne KnSe ��■� DD No ne ane Knee � ane Knee � ... ...... ne ane ■�ne� . ... • ne �ne■�nee� . :, ne��ne■�■�oee�� - ne■��ne�■�oe■�� - ne■�■�ne�■�oee�■� • ne■�■�ne�■�oee�■� • ne�ne�■�nee■� . ne■�■�oe�■�nee�■� = ne��oe�■�oee�■� -. • - - ne��ne��nee�� ne►�®e �.�s®�nee� ne $-N Q-4 ne m> F-14 19 s--.4nee � �0 P-140; -.►�rnADD ee � Dnit ne �►�Pes �s -nee � AD ,7. Addressable Devices oe■�■� �,■s•�•�► -•roe , , • � ne , ,,, , �►..■r--•as;-0oee � • ; ne ��►z.■► •rte =�oee�� o©� oee� ►-�■► oee�� ne■�� s■s�oee�� ne■�■��.■► -.��=moo©. ,,, � ne■�■�►<�■sem-+o�oe�� OUIS ne■�■� �,■► •amnee�� oe■�� ■► -.ate oee�� ne■�ne �oee■� ;; ' . oe■��ne ; ; ;'; �oee�■� Viannni— ': 1.-. ne■ ■ane■ �oee�■� .ne ane �nee■■� • neff-rlmx�neTotal Knee ■� Non - -- '=_ == = ES-415;,�,.f SECURITY CORPORATION INNOVATION 7707 Fire Subscribers InteffiNet 2 Introducing { Suarter Alam, am s New Feature Highlights aes-corp.com n • Leverages state of the art technology —Mww • @' Applies advanced security protection 4 @ • Offers flexible power and configuration options NFFW usreu • Engineered for backward compatibility with legacy systems • Enables future ready capabilities • Provides instant subscriber status through front panel with Power and Trouble LEDs, a backlit LCD display, and Menu/Silence button • Improves functionality with an adaptive Graphic User Interface (GUI) for programming via smartphones, tablet and PCs • Plus many more... Key Benefits that Make 2.0 the Best Alarm Monitoring Solution Ever • Built upon the solid foundation of AES-IntelliNet patented mesh radio technology for use in private licensed wireless networks • Protects subscriber units against unauthorized access and rogue activity with a password protected Dealer Code • Makes programming and streamlined troubleshooting easy with user friendly interface • Adds integrated supervision of AES-IntelliPro full data module • Provides versatile power options: (1) Direct from the Fire Alarm Control Panel (FACP) without requiring an electrician onsite and without Subscriber backup battery (2) Directly from the FACP with Subscriber backup battery; or (3) Traditional installation with plug in Class 2 low power transformer • Allows for enhancement upgrades and an expanded number of new features to be added easily with highly flexible and scalable alarm communications infrastructure • Rigorously tested to the highest industry standards and future ready to meet emerging NFPA code and UL standards Enhanced Wireless Fire Alarm Monitoring Powered by AES enhanced mesh radio technology, IntelliNet 2.0 7707 Fire Subscribers are next generation universal wireless communicators that provide advanced security protection for any new or existing alarm monitoring network. The AES Model 7707 is ideal for commercial fire applications. With the AES-IntelliPro full data module option, they are the ideal drop-in replacement for Plain Old Telephone Service (POTS) lines. The red metal enclosure comes with a key lock and front panel LCD backlit display with intuitive view that provides an instant visual of the subscriber status. The user friendly GUI makes it easy to program AES subscriber units via a smartphone, laptop, tablet, or integrated Universal Serial Bus (USB)—without the need for special cables or having to use a handheld programmer. Additional knockouts make it easier to mount for faster installation. IntelliNet 2.0 Private Wireless Mesh Radio Network D) Burglary Subscriber _ ' - - - - ^ - ^ _ - >aa1 L B d . d r C < � t r B} Fre Subscriber . + 1 •a d t ��arnogua.nrrymm -- ---^-^ ^ �u D rarsur.r ------ B — — — ` —Frhnary AESMYHMrr ReceWer - � r 1 � All Alarm ti r r Panel 1 t secondary AESMdWV tRttNva 'C Alarm Automation AQIP Links Customer Location Mesh Radio Technology Central Monitoring Station Alarm Panel & AES Subscriber Multi -path AESdn!ell;afei & Nehvork primary & Secondary AFS-MaRiNe: System sends onical event signor delivers alarm sigrwrs v a smart routing recewes transmisswn in 1-3 seconds The IntelliNet 2.0 Fire Subscriber has an 8 Zone modular design for expansion with normal and reverse polarity, POTS and DACT interfaces with an option for the 7794A AES-IntelliPro full data module add-on accessory board. AES subscribers' intelligent software automatically detects new hardware and devices to reduce installation time. An RES certified WiFi accessory allows seamless wireless connectivity for configuration and programming. A laptop, Ethernet cable, or a Wi-Fi USB dongle is required for IntelliNet 2.0 programming, handheld programmers will not work with 2.0 units. A FACP Power Supply Adapter is required for certain configurations when using flexible power options. The forward compatible design allows for feature add-ons, engineered to adapt seamlessly with future software upgrades as technology advances. IntelliNet 2.0 allows configuration cloning for faster installation time. The AES 7707 was designed with quick configuration and installation in mind to make it easier for field technicians to get in, out, and on to the next install. Visit our Fire Marshal Resources web page for official NFPA and UL Listings: http://aes-corp.com/products/fire/fire-marshal-resources/ How to Order 7707 Fire IntelliNet 2.0 Fire Subscribers 2.0 PREMIUM (UL & ULC Listed, Available Now!) 7707P-88 IntelliNet 2.0 Fire Subscriber, 8 Zone, 8 Supervised Zones, with integrated onboard Local Annunciator, Red Enclosure 7707P 8$ ULP IntelliNet 2.0 Fire Subscriber, 8 Zone, 8 Supervised Zones with 7794A AES-IntelliPro and integrated onboard Local Annunciator, Red Enclosure IntelliNet2.0 Fire Subscriber, 4 Zone, 4 Supervised Zones, with integrated onboard 7707P-44 Local Annunciator, Red Enclosure IntelliNet 2.0 Fire Subscriber, 4 Zone, 4 Supervised Zones with 7794A AES-IntelliPro 7707P-44-ULP and integrated onboard Local Annunciator, Red Enclosure 2.0 FEATURE ADD (Pending UL Review) 7707P -88-M IntelliNet 2.0 Fire Subscriber, 8 Zone with Multiple Communication Technologies (MCT), Red Enclosure IntelliNet 2.0 Fire Subscriber, 8 Zone with 7794A AES-IntelliPro, and integrated 7707P-88-ULP-M onboard Local Annunciator plus MCT, Red Enclosure IntelliNet 2.0 Fire Subscriber, 4 Zone with Multiple Communication Technologies 7707P -44-M (MCT), Red Enclosure IntelliNet 2.0 Fire Subscriber, 4 Zone with 7794A AES-IntelliPro, and integrated 7707P-44-ULP-M onboard Local Annunciator plus MCT, Red Enclosure 7707M-UPG IntelliNet 2.0 Fire MCT Software Upgrade 2.0 ACCESSORIES Standalone AES-IntelliPro Fire full data module add-on accessory board with 7794A firmware for new IntelliNet 2.0 units only, cannot be used in legacy units 77-WiFi AES certified WiFi adapter 77-FACPA FRCP Power Supply Adapter for internal mount 77-FACPA-KIT External installation hardware for 2 -way Junction Box •- Legacy Fire Subscribers Integrated Fire Monitoring System, Red Enclosure 7706-ULF 7706-U 7788F-ULP-P Legacy Fire Subscriber, 8 Zone with 7795 AES-IntelliPro (7794 full data module, 7762 hardware supervisory module, and 7740 Local Annunciator), Red Enclosure 7788F-ULP Legacy Fire Subscriber, 8 Zone, 8 Supervised Zones with 7794 AES-IntelliPro, Red Enclosure 7788F Legacy Fire Subscriber, 8 Zone, 8 Supervised Zones, Red Enclosure 7744E-ULP-P Legacy Fire Subscriber, 4 Zone with 7795 AES-IntelliPro (7794 full data module, 7762 hardware supervisory module, and 7740 Local Annunciator), Red Enclosure 7744F-ULP Legacy Fire Subscriber, 4x4 Zone, 4 Supervised Zones with 7794 AES-IntelliPro, Red Enclosure 7744F Legacy Fire Subscriber, 4x4 Zone, 4 Reversing Polarity, 4 Supervised Zones, Red Enclosure LEGACY ACCESSORIES Standalone AES-IntelliPro Fire full data module add-on accessory board for legacy 7794 units only, please see 7794A above for IntelliNet 2.0 version Technical Specifications DIMENSIONS 13"H x 85"W x 4.5"D (33cmH x 21.5cmW x 11.4cmD) WEIGHT 5.8 lbs (2.6 kilograms) excluding battery 13 lbs (5.9 kilograms) with 10 Ah battery RADIO FREQUENCY Standard Frequency Range: 450-470 MHz Contact AES for other UHF and VHF frequencies ANTENNA 2.5 dB tamper resistant antenna included, mounts on enclosure Optional remote mounting antenna available POWER INPUT AC SOURCES Transformer: Class 2 16.5V AC nominal output 1.9 A max current (40 VA MIN) ELK ELK-TRG1640, MG ELECTRONIC SALES MGT1640, or AES 1640 (not included) DC SOURCES (includes FACP) 24V DC Regulated Power Supply with Subscriber Rechargeable Battery 1.9 A max current BACKUP BATTERY 10-12 Ah, UL recognized lead acid gel cell, size based on subscriber configuration Contact Us ALARM SIGNAL INPUTS/ZONES 8 individually programmable E.O.L. type zone inputs 4+4: 4 reverse polarity input and 4 individually programmable E.O.L. type zone inputs Optional 7794A AES-1nte11iPro for full data via Contact ID, Pulse, Modem Ile and Modem Ilial UL LISTINGS UL 864 10th Edition Standard for Control Units and Accessories for Fire Alarm Systems ULC S559-04 1st Edition Equipment for Fire Signal Receiving Centres and Systems TROUBLE OUTPUT—ACK DELAY/ANTENNA CUT Form C relay, fail secure, rated 24V DC 1A resistive, unsupervised RESET BUTTON Located on main circuit board OPERATING TEMPERATURE 32 to 120°F (0 to 49°C) STORAGE TEMPERATURE 14 to 140°F (-10 to 60°C) RELATIVE HUMIDITY 0 to 93%, non -condensing RECHARGE CAPABILITY Will charge 12V battery size from 10-12 Ah 7707 Fire PORTS Ethernet for configuration and message communication USB access for software upgrade REMOTE ANNUNCIATOR AES Model 7740 Remote Annunciator, supervised COMPATIBLE RECEIVERS 7705i AES-MultiNet Receiver CONFIGURATION INTERFACE Web browser capable device accessible via smartphone, tablet, laptop, or PC CURRENT CONSUMPTION Standby w/ charged backup battery: 200 mA (1.2 A Transmitting) Standby + charging backup battery: 900 mA (1.9 A Transmitting - MAX) POWER OUTPUT 2 or 5 Watts Factory set ENCLOSURE MATERIAL Steel with paint finish FINISH COLOR Red VISUAL INDICATORS Front panel LCD (2 x 20 alphanumeric character backlit display) Power and Trouble LEDs (ALM, Trouble, Tx, Rx, WA) For pricing and availability or to learn more about lntelliNet 2.0, please call your local AES Sales Representative at (800) 237-6387 or email sales@aes-corp.com. NOT-BG 12LX Addressable Manual Pull Station The Notifier NOT-BG12LX is a state-of-the-art, dual -action (i.e., requires two motions to activate the station) pull station that includes an addressable interface for Fire Warden series intelligent control panels, and the NSP -25 panel. Because the NOT -BG 12LX is addressable, the control panel can display the exact location of the activated manual station. This leads fire personnel quickly to the location of the alarm. Features • Maintenance personnel can open station for inspection and address setting without causing an alarm condition. • Built-in bicolor LED, which is visible through the handle of the station, flashes in normal operation and latches steady red when in alarm. • Handle latches in down position and the word "ACTIVATED" appears to clearly indicate the station has been operated. • Captive screw terminals wire -ready for easy connection to SLC loop (accepts up to 12 AWG/3.25 mm2 wire). • Can be surface mounted (with SB -10 or SB -1/0) or semi - flush mounted. Semi -flush mount to a standard single - gang, double -gang, or 4" (10.16 cm) square electrical box. • Smooth dual -action design. • Meets ADAAG controls and operating mechanisms guide- lines (Section 4.1.3[13]); meets ADA requirement for 5 Ib. maximum activation force. • Highly visible. • Attractive shape and textured finish. • Key reset. • Includes Braille text on station handle. • Optional trim ring (BG12TR). • Meets UL 38, Standard for Manually Actuated Signaling Boxes. Construction Shell, door, and handle are molded of durable polycarbonate material with a textured finish. Specifications • Shipping Weight: 9.6 oz. (272.15 g) • Normal operating voltage: 24 VDC. • Maximum SLC loop voltage: 28.0 VDC. • Maximum SLC standby current: 375 pA. • Maximum SLC alarm current: 5 mA. • Temperature Range: 32°F to 120°F (0°C to 49°C) • Relative Humidity: 10% to 93% (noncondensing) • For use indoors in a dry location Installation The NOT-BG12LX will mount semi -flush into a single -gang, double -gang, or standard 4" (10.16 cm) square electrical outlet box, or will surface mount to the model SB -10 or SB -1/0 sur- face backbox. If the NOT-BG12LX is being semi -flush mounted, then the optional trim ring (BG12TR) may be used. DN -7001:D • Al -380 0 • _o •VE to]- Intelligent/Addressable Devices The NOT-BG12LX Addressable Manual Pull Station The BG12TR is usually needed for semi -flush mounting with 4" (10.16 cm) or double -gang boxes (not with single -gang boxes). Operation Pushing in, then pulling down on the handle causes it to latch in the down/activated position. Once latched, the word "ACTI- VATED" (in bright yellow) appears at the top of the handle, while a portion of the handle protrudes from the bottom of the station. To reset the station, simply unlock the station with the key and pull the door open. This action resets the handle; clos- ing the door automatically resets the switch. Each manual station, on command from the control panel, sends data to the panel representing the state of the manual switch. Two rotary decimal switches allow address settings (1 — 99 on NFW2-1OWN FW2-100C, 1 — 50 for N FW -50/N FW - 50C). Architectural/Engineering Specifications Manual Fire Alarm Stations shall be non -coded, with a key - operated reset lock in order that they may be tested, and so designed that after actual Emergency Operation, they cannot be restored to normal except by use of a key. An operated sta- tion shall automatically condition itself so as to be visually detected as activated. Manual stations shall be constructed of red -colored polycarbonate material with clearly visible operat- ing instructions provided on the cover. The word FIRE shall appear on the front of the stations in white letters, 1.00 inches (2.54 cm) or larger. Stations shall be suitable for surface mounting on matching backbox SB -10 or SB -I/O; or semi -flush mounting on a standard single -gang, double -gang, or 4" (10.16 cm) square electrical box, and shall be installed DN -7001:D • 4/13/2012 — Page 1 of 2 within the limits defined by the Americans with Disabilities Act (ADA) or per national/local requirements. Manual Stations shall be Underwriters Laboratories listed. Manual stations shall connect with two wires to one of the con- trol panel SLC loops. The manual station shall, on command from the control panel, send data to the panel representing the state of the manual switch. Manual stations shall provide address setting by use of rotary decimal switches. Product Line Information NOT BG12LX: Dual -action addressable pull station. Includes key locking feature. (Listed for Canadian and non -Canadian applications.) SB -10: Surface backbox; metal. SB -1/0: Surface backbox; plastic. BG12TR: Optional trim ring. 17021: Keys, set of two. Agency Listings and Approvals In some cases, certain modules or applications may not be listed by certain approval agencies, or listing may be in pro- cess. Consult factory for latest listing status. • UL/ULC Listed: S692 (listed for Canadian and non -Cana- dian applications). • MEA: 67-02-E Vol. IV. • CSFM:7150-0028:0199. • FM Approved. Patented: U.S. Patent No. D428,351; 6,380,846; 6,314,772; 6,632,108. NOTIFIERO is a registered trademark of Honeywell International Inc. 02012 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited. I�O �oo� This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. ENGINEERINS & MANUFACTURING All specifications are subject to change without notice. QUALITY SYSTEMS Made in the U.S. A. For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118. www.notifier.com Page 2 of 2 — DN -7001:D • 4/13/2012 NP -100(A) Series Addressable Photoelectric DN -6995:D • Ai -320 0 NOTIFIER° Detectors by Honeywell Addressable Devices General The NP -100(A), NP-10OT(A) and NP-10OR(A) addressable, low -profile plug-in photoelectric detectors use a state-of-the-art photoelectric sensing chamber with communications to provide open area protection and are used exclusively with NOTIFIER's FireWarden Series (FireWarden-100-2 and FireWarden-50) and Spartan (NSP -25) Addressable Fire Alarm Control Panels (FACPs). The NP-10OT(A) adds thermal sensors that will alarm at a fixed temperature of 135°F (57°C). Since these detectors are addressable, they will help emergency personnel quickly locate a fire during its early stages, potentially saving precious rescue time while also reducing property damage. Two LEDs on each sensor light to provide a local, visible sensor indication. Remote LED annunciator capability is available as an optional accessory, PN RA10OZ(A). The NP-10OR(A) is a remote test capable detector for use with DNR(A)/DNRW duct smoke detec- tor housings. Features SLC LOOP • Two -wire loop connection. • Unit uses base for wiring. ADDRESSING • Addressable by device. • Rotary, decimal addressing: 01 – 99 with FireWarden-100-2 and NSP -25, and 01 – 50 with FireWarden-50. ARCHITECTURE • Unique single -source, dual-chamber design to respond quickly and dependably to a broad range of fires. • Sleek, low -profile design. • Integral communications and built-in type identification. • Built-in tamper-resistant feature. • Removable cover and insect -resistant screen for simple field cleaning. OPERATION • Withstands air velocities up to 4,000 feet -per -minute (20 m/ sec.) without triggering a false alarm. • Factory preset at 1.5% nominal sensitivity for panel alarm threshold level. • Visible LED "blinks" when the unit is addressed (communicat- ing with the fire panel) and latches on in alarm. MECHANICALS • Sealed against back pressure. • Direct surface mounting or electrical box mounting. • Mounts to: single -gang box, 3.5" (8.89 cm) or 4.0" (10.16 cm) octagonal box, or 4.0" (10.16 cm) square electrical box (using a plaster ring — included). OTHER SYSTEM FEATURES • Fully coated circuit boards and superior RF/transient protec- tion. • 94 -VO plastic flammability rating. • Low standby current. a NP -100(A) in B210LP(A) Base OPTIONS • Remote LED output connection, PN RA100Z(A). Applications Use photoelectric detectors in life -safety applications to provide a broad range of fire -sensing capability, especially where smol- dering fires are anticipated. Ionization detectors are often better than photoelectric detectors at sensing fast, flaming fires. Construction These detectors are constructed of off-white fire resistant plas- tic. NP -100(A) series plug-in, low -profile smoke detectors are designed to commercial standards and offer an attractive appearance. Installation NP -100(A) series plug-in detectors use a detachable mounting base to simplify installation, service and maintenance. Mount base (all base types) on an electrical backbox which is at least 1.5" (3.81 cm) deep. For a chart of compatible junction boxes, see DN -60054. NOTE: Because of the inherent supervision provided by the SLC loop, end -of -line resistors are not required. Wiring 7 --taps" or branches are permitted for Style 4 (Class B) wiring. NP-10OR(A) mounts in a DNR(A)/DNRW duct detector housing. Operation Each NP -100(A) series detector uses one of 99 possible addresses on the FireWarden-100-2 and NSP -25, or one of 50 possible addresses on the FireWarden-50 Signaling Line Circuit (SLC). It responds to regular polls from the system and reports its type and status. The addressable photoelectric sensor in the NP -100(A) series has a unique unipolar chamber that responds quickly and uni- formly to a broad range of smoke conditions. It can withstand wind gusts up to 4,000 feet -per -minute (20 m/sec.) without sending an alarm level signal. Because of its unipolar chamber, the NP -100(A) series is approximately two times more respon- sive than most photoelectric sensors. This makes it a more sta- ble detector. DN -6995:D • 2/11/2015 — Page 1 of 2 Detector Sensitivity Test Each detector can have its sensitivity tested (required per NFPA 72, Chapter 14 on Inspection, Testing and Maintenance) when installed/connected to a FireWarden-100-2 or FireWarden-50 addressable fire alarm control panel. The results of the sensitiv- ity test can be printed off the FireWarden-100-2 or FireWarden- 50 for record keeping. Specification Voltage range: 15 - 32 VDC (peak). Standby current: 300 pA @ 24 VDC. LED current: 6.5 mA @ 24 VDC (latched `OM'). Air velocity: 4,000 ft./min. (20 m/sec.) maximum. Size: 2.1" (5.33 cm) high; base determines diameter. - B210LP(A): 6.1" (15.5 cm) diameter. - B501 (A): 4.1" (10.4 cm) diameter. - B200SR(A): 6.875" (17.46 cm) diameter. - B224RB(A): 6.2" (15.748 cm) diameter. Weight: 3.6 oz. (102 g). Operating temperature range: for NP -100(A): 0°C to 49°C (32°F to 120°F); for NP-100T(A): 0°C to 38°C (32°F to 100°F). NP-100R(A): installed in a DNR(A)/DNRW -20°C to 70°C (-4°F to 158°F). Temperature: 0°C - 49°C (32°F - 120°F). Relative humidity: 10%- 93%, non -condensing. Listings Listings and approvals below apply to the NP -100(A), NP- 100T(A), and NP-100R(A) detectors. In some cases, certain modules may not be listed by certain approval agencies, or list- ing may be in process. Consult factory for latest listing status. • UL Listed: S1115. • ULC Listed: S1115. • CSFM:7272-0028:0231. • MEA: 243-02-E Vol. 2. • Maryland State Fire Marshal: permit 2173. • FM approved. Product Line Information NOTE: "A" suffix indicates ULC Listed model. NP -100: Addressable photoelectric detector; B21OLP base included. NP-10OA: Sames as NP -100 with ULC Listing; B21OLPA base included. NP-10OT: Same as NP -100 but with thermal element; B21 OLP base included. NP-100TA: Same as NP -100T with ULC Listing; B21OLPA base included. NP-10OR: Remote test capable addressable photoelectric detector for use with a DNRA/DNRW duct detector housing; B21 OLP base included. NP-100RA: Same as NP-10OR with ULC Listing for use with a DNRA duct detector housing; B210LPA base included. INTELLIGENT BASES NOTE: A" suffix indicates ULC Listed model. NOTE: For details about intelligent bases and their mounting, see DN -60054. B210LP(A): Plug-in detector base (included); standard U.S. flanged low -profile mounting base. B21OLPBP: Bulk pack of B210LP; package contains 10. B501 (A): Standard European flangeless mounting base. 8501 BP: Bulk pack of B501; package contains 10. B200SR(A): Intelligent sounder base capable of producing sound output with ANSI Temporal 3 or continuous tone. Replaces B501 BH series bases in retrofit applications. B224RB(A): Plug-in System Sensor relay base. Screw termi- nals: up to 14 AWG (2.0 mm2). Relay type: Form -C. Rating: 2.0 A @ 30 VDC resistive; 0.3 A @ 110 VDC inductive; 1.0 A @ 30 VDC inductive. 8224BI(A): Plug-in System Sensor isolator detector base. Maximum 25 devices between isolator bases (see DN -6994). ACCESSORIES F110: Retrofit flange to convert B210LP(A) to match the B710LP(A) profile, or to convert older high-profile bases to low - profile. F110BP: Bulk pack of F110; package contains 15. F210: Replacement flange for 8210LP(A) base. RA100Z(A): Remote LED annunciator. 3 - 32 VDC. Mounts to a U.S. single -gang electrical box. For use with B501 (A) and 8210LP(A) bases only. SMB600: Surface mounting kit M02-04-00:Test magnet. M02-09-00: Test magnet with telescoping handle. XR213: Detector removal tool. Allows installation and/or removal of detector heads from bases in high ceiling applications. XP -4: Extension pole for XR2B. Comes in three 5 -foot (1.524 m) sections. T55-127-010: Detector removal tool without pole. BCK-20OB: Black detector covers for use with NP -100(A) only; box of 10. WCK-20OB: White detector covers for use with NP -100(A) only; box of 10. NOTIFIERO and FireWardenO are registered trademarks of Honeywell International Inc. ©2015 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited. I��' 9001 This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. 111113-33.10a= We cannot cover all specific applications or anticipate all requirements. ENRINEERI'IC IMANUFACTURING All specifications are subject to change without notice. QUALITY SYSTEMS For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118. www.notifier.com Page 2 of 2 - DN -6995: D • 2/11/2015 NH -100(A) Series Intelligent Addressable Thermal DN -6997:D • Al -320 0 NOTIFIER @ Detectors for FireWarden Series by Honeywell Addressable General The NOTIFIER NH -100(A) Series thermal detectors are addressable sensors that use a state-of-the-art thermistor sensing circuit for fast response. These sensors provide open - area protection and are intended for use with FireWarden Series (FireWarden-100-2 and FireWarden-50) and Spartan (NSP -25) addressable Fire Alarm Control Panels (FACPs). The NH -100(A) and NH-100R(A) sensors provide fixed tem- perature alarm detection at 135°F (57°C). The NH-100R(A) sensor also responds to rate -of -rise conditions of greater than 15°F (8.3°C) per minute. The NH-100H(A) is a fixed high-tem- perature detector that activates at 190°F (88°C). These ther- mal detectors provide addressable property protection in a variety of applications. Two LEDs on each sensor light to provide a local, visible sen- sor indication. Remote LED annunciator capability is available using an optional accessory, the RA100Z. Features SLC loop: • Two -wire SLC loop connection. • Unit uses base for wiring. Addressing: • Addressable by device. • Rotary, decimal addressing: 01 — 99 with FireWarden-100- 2, NSP -25, 01 — 50 with FireWarden-50. Architecture: • Sleek, low -profile, stylish design. • State-of-the-art thermistor technology for fast response. • Integral communications and built-in device -type identifica- tion. • Built-in tamper resistant feature. • Built-in functional test switch activated by external magnet. Operation: • Factory preset at 135°F (57°C) for the NH -100(A) and NH- 100R(A); 190°F (88°C) for the NH-100H(A). • Rate -of -rise triggers at 15°F (8.3°C) per minute for the NH- 100R(A). • 360° -field viewing angle of the visual alarm indicators (two bicolor LEDs). LEDs blink red in Normal condition and turn on steady red in Alarm. • Visible LEDs "blink" every time the unit is addressed. Mechanicals: • Sealed against back pressure. • SEMS screws for wiring of the separate base. • Designed for direct -surface or electrical -box mounting. • Plugs into separate base for ease of installation and main- tenance. • Separate base allows interchange of photoelectric, ioniza- tion and thermal sensors. Other system features: Remote test feature from the panel. Walk test with address display. NH -100(A) in B210LP(A) Base Low standby current. 94-5V plastic flammability rating. Options: • Remote LED output connection to optional RA100Z remote LED annunciator. • Flanged surface mounting kit. Installation NH -100(A) Series plug-in intelligent thermal detectors use a detachable base to simplify installation, service and mainte- nance. Installation instructions are shipped with each detector. Mount base (all base types) on an electrical backbox which is at least 1.5" (3.81 cm) deep. For a chart of compatible junction boxes, see DN -60054. NOTE: Because of the inherent supervision provided by the SLC loop, end -of -line resistors are not required. Wiring 7 --taps" or branches are permitted for Style 4 (Class `B) wiring only. Applications Use thermal detectors for protection of property. Construction These detectors are constructed of off-white fire-resistant plastic. The NH -100(A) Series plug-in intelligent thermal detectors are designed to commercial standards and offer an attractive appearance. Operation Each NH -100(A) Series detector uses one of 99 (FireWarden- 100-2, NSP -25) or 50 (FireWarden-50) possible addresses on a control panel SLC loop. It responds to regular polls from the control panel and reports its type and the status. If it receives a test command from the panel (or a local magnet test), it stimu- lates its electronics and reports an alarm. It blinks its LEDs when polled and turns the LEDs on when commanded by the panel. The NH -100(A) Series offers features and performance that represent the latest in thermal detector technology. DN -6997:D • 5/17/13 — Page 1 of 2 Spefications Size: 2.1" (5.3 cm) high; base determines diameter. — B210LP(A): 6.1" (15.5 cm) diameter. — B501(A): 4.1" (10.4 cm) diameter. — B200SR(A): 6.875" (17.46 cm) diameter. — B224RB(A): 6.2" (15.748 cm) diameter. Shipping weight: 4.8 oz. (137 g). Installation temperature: — NH -100(A), NH-100R(A): —4°F to 100°F (-20°C to WC). — NH-100H(A): —4°F to 150°F (-20°C to 66°C). Humidity range: 10% to 93% relative humidity (noncon- densing). Voltage range: 15 to 32 VDC peak. Standby current: 300 pA @ 24 VDC (one communication every five seconds with LED blink enabled). LED current: 6.5 mA @ 24 VDC. Mounting: B21OLP(A) flanged base, included. See "Product Line Information: Intelligent Bases" if using a different base. Fixed -temperature setpoint: 135°F (57°C) for the NH -100 and NH-100R(A)(A); 190°F (88°C) for the NH-100H(A). Rate -of -rise detection: responds to greater than 15°F (8.3°C) per minute. Listings and Approvals Listings and approvals below apply to the NH -100(A) Series detectors. In some cases, certain modules may not be listed by certain approval agencies, or listing may be in process. Consult factory for latest listing status. • UL Listed: S747. • ULC Listed: S747. • CSFM:7270-0028:0234. • MEA: 387-02-E Vol. II. • FM approved. Product Line Information NOTE: 'A" suffix indicates ULC Listed model. NH -100: Intelligent thermal sensor; 135° F (57° C); B21OLP base included. NH-10OA: Same as NH -100 but with ULC Listing; B21OLPA base included. NH-10OR: Same as NH -100 with rate -of -rise feature; B21OLP base included. NH-100RA: Same as NH-10OR but with ULC Listing; B21 OLPA base included. NH-10OH: Intelligent fixed high-temperature thermal detector; 190° F (88° C); B21OLP base included. NH-100HA: Same as NH -100H but with ULC Listing; B21 OLPA base included. INTELLIGENT BASES NOTE: 'A" suffix indicates ULC Listed model. NOTE: For details about intelligent bases and their mounting, see DN -60054. B210LP(A): Plug-in detector base (included); standard U.S. flanged low -profile mounting base. B21 OLPBP: Bulk pack of B21OLP; package contains 10. B501(A): Standard European flangeless mounting base. 8501 BP: Bulk pack of B501; package contains 10. B200SR(A): Intelligent sounder base capable of producing sound output with ANSI Temporal 3 or continuous tone. Replaces B501 BH series bases in retrofit applications. B224RB(A): Plug-in System Sensor relay base. Screw termi- nals: up to 14 AWG (2.0 mm2). Relay type: Form -C. Rating: 2.0 A @ 30 VDC resistive; 0.3 A @ 110 VDC inductive; 1.0 A @ 30 VDC inductive. B224BI(A): Plug-in System Sensor isolator detector base. Maximum 25 devices between isolator bases (see DN -6994). ACCESSORIES F110: Retrofit flange to convert B21OLP(A) to match the B710LP(A) profile, or to convert older high-profile bases to low -profile. F110BP: Bulk pack of F110; package contains 15. F210: Replacement flange for B21OLP(A) base. RA100Z(A): Remote LED annunciator. 3 — 32 VDC. Mounts to a U.S. single -gang electrical box. For use with B501(A) and B210LP(A) bases only. SMB600: Surface mounting kit M02-04-00:Test magnet. M02-09-00: Test magnet with telescoping handle. XR213: Detector removal tool. Allows installation and/or removal of detector heads from bases in high ceiling applica- tions. XP -4: Extension pole for XR2B. Comes in three 5 -foot (1.524 m) sections. T55-127-010: Detector removal tool without pole. NOTIFIER® and FireWarden® are registered trademarks of Honeywell International Inc. @2013. All rights reserved. Unauthorized use of this document is strictly prohibited. I O 9001 This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. ENGINEERING & MANUFACTURING All specifications are subject to change without notice. QUALITY SYSTEMS Made in the U.S. A. For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118. www.notifier.com Page 2 of 2 — DN -6997:D • 5/17/13 Monitor Modules NMM-100(A), NMM-100P(A), NZM-100(A), and NDMA 00(A) for FireWarden Series 1�7�S:kkR7f� �J NOTI FI E R° by Hon eywe I I Intelligent Addressable Devices General Four different monitor modules are available for Notifier's FireWarden Series intelligent control panels for a variety of applications. Monitor modules supervise a circuit of dry -con- tact input devices, such as conventional heat detectors and pull stations, or monitor and power a circuit of two -wire smoke detectors (NZM-100(A)). NMM-100(A) is a standard -sized module (typically mounts to a 4" [10.16 cm] square box) that supervises either a Style D (Class A) or Style B (Class B) circuit of dry -contact input devices. NMM-100P(A) is a miniature monitor module a mere 1.3" (3.302 cm) H x 2.75" (6.985 cm) W x 0.65" (1.651 cm) D that supervises a Style B (Class B) circuit of dry -contact input devices. Its compact design allows the NMM-100P(A) to be mounted in a single -gang box behind the device it monitors. NZM-100(A) is a standard -sized module that monitors and supervises compatible two -wire, 24 volt, smoke detectors on a Style D (Class A) or Style B (Class B) circuit. NDM-100(A) is a standard -sized dual monitor module that monitors and supervises two independent two -wire Style B (Class B) dry -contact initiating device circuits (IDCs) at two separate, consecutive addresses in intelligent, two -wire sys- tems. LiteSpeedTM is a communication protocol that greatly increases the speed of communication between analog intel- ligent devices. Intelligent devices communicate in a grouped fashion. If one of the devices within the group has new infor- mation, the panel CPU stops the group poll and concentrates on single points. The net effect is response speed greater than five times that of other communication protocols. NMM-100(A) Monitor Module • Built-in type identification automatically identifies this device as a monitor module to the control panel. • Powered directly by two -wire SLC loop. No additional power required. • High noise (EMF/RFI) immunity. • SEMS screws with clamping plates for ease of wiring. • Direct -dial entry of address: 01 — 99 on FireWarden-100- 2, 01 — 50 on FireWarden-50. • LED flashes during normal operation and latches on steady to indicate alarm. The NMM-100(A) Monitor Module is intended for use in intel- ligent, two -wire systems, where the individual address of each module is selected using the built-in rotary switches. It provides either a two -wire or four -wire fault-tolerant Initiating Device Circuit (IDC) for normally -open -contact fire alarm and supervisory devices. The module has a panel -controlled LED indicator. NMM-100(A) APPLICATIONS Use to monitor a zone of four -wire smoke detectors, manual fire alarm pull stations, waterflow devices, or other normally - open dry -contact alarm activation devices. May also be used NMM-100(A) (Type H) to monitor normally -open supervisory devices with special supervisory indication at the control panel. Monitored circuit may be wired as an NFPA Style B (Class B) or Style D (Class A) Initiating Device Circuit. A 47K Ohm End -of -Line Resistor (provided) terminates the Style B circuit. No resistor is required for supervision of the Style D circuit. NMM-100(A) OPERATION Each NMM-100(A) uses one of the available module addresses on an SLC loop. It responds to regular polls from the control panel and reports its type and the status (open/ normal/short) of its Initiating Device Circuit (IDC). A flashing LED indicates that the module is in communication with the control panel. The LED latches steady on alarm (subject to current limitations on the loop). NMM-100(A) SPECIFICATIONS Nominal operating voltage: 15 to 32 VDC. Maximum current draw: 5.0 mA (LED on). Average operating current: 375 pA (LED flashing), 1 com- munication every 5 seconds, 47k EOL. Maximum IDC wiring resistance: 1500 Ohms. Maximum IDC Voltage: 11 Volts. EOL resistance: 47K Ohms. Temperature range: 32°F to 120°F (0°C to 49°C). Humidity range: 10% to 93% noncondensing. Dimensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x 1.25" (3.175 cm) deep. Mounts to a 4" (10.16 cm) square x 2.125" (5.398 cm) deep box. NMM-100P(A) Mini Monitor Module • Built-in type identification automatically identifies this device as a monitor module to the panel. DN -6999:E • 07/30/2015— Pagel of 4 • Powered directly by two -wire SLC loop. No additional power required. • High noise (EMF/RFI) immunity. • Tinned, stripped leads for ease of wiring. • Direct -dial entry of address: 01 — 99 on FireWarden-100-2, 01 — 50 on FireWarden-50. 3 1415 0 1 ADDRESS 0 1 s 2 2 2 3 11 "" 4 LOOP O 4 109 8 7 65 9 8 7 65 TENS ONES O W U Ocl� m The NMM-100P(A) Mini Monitor Module can be installed in a single -gang junction directly behind the monitored unit. Its small size and light weight allow it to be installed without rigid mounting. The NMM-100P(A) is intended for use in intelli- gent, two -wire systems where the individual address of each module is selected using rotary switches. It provides a two - wire initiating device circuit for normally -open -contact fire alarm and security devices. NMM-100P(A) NMM-100P(A) APPLICATIONS Use to monitor a single device or a zone of four -wire smoke detectors, manual fire alarm pull stations, waterflow devices, or other normally -open dry -contact devices. May also be used to monitor normally -open supervisory devices with spe- cial supervisory indication at the control panel. Monitored cir- cuit/device is wired as an NFPA Style B (Class B) Initiating Device Circuit. A 47K Ohm End -of -Line Resistor (provided) terminates the circuit. NMM-100P(A) OPERATION Each NMM-100P(A) uses one of the available module addresses on an SLC loop. It responds to regular polls from the control panel and reports its type and the status (open/ normal/short) of its Initiating Device Circuit (IDC). NMM-100P(A) SPECIFICATIONS Nominal operating voltage: 15 to 32 VDC. Average operating current: 350 pA, 1 communication every 5 seconds, 47k EOL; 600 pA Max. (Communicating, IDC Shorted). Maximum IDC wiring resistance: 1500 Ohms. Maximum IDC Voltage: 11 Volts. Maximum IDC Current: 450 NA. EOL resistance: 47K Ohms. Temperature range: 32°F to 120°F (0°C to 49°C). Humidity range: 10% to 93% noncondensing. Dimensions: 1.3" (3.302 cm) high x 2.75' (6.985 cm) wide x 0.65' (1.651 cm) deep. Page 2 of 4 — DN -6999:E • 07/30/2015 Wire length: 6" (15.24 cm) minimum. NZM-100(A) Interface Module • Supports compatible two -wire smoke detectors. • Supervises IDC wiring and connection of external power source. • High noise (EMF/RFI) immunity. • SEMS screws with clamping plates for ease of wiring. • Direct -dial entry entry of address:, 01 — 99 on FireWarden- 100-2, 01 — 50 on FireWarden-50. • LED flashes during normal operation. • LED latches steady to indicate alarm on command from control panel. The NZM-100(A) Interface Module is intended for use in intelligent, addressable systems, where the individual address of each module is selected using built-in rotary switches. This module allows intelligent panels to interface and monitor two -wire conventional smoke detectors. It trans- mits the status (normal, open, or alarm) of one full zone of conventional detectors back to the control panel. All two -wire detectors being monitored must be UL compatible with the module. NZM-100(A) APPLICATIONS Use the NZM-100(A) to monitor a zone of two -wire smoke detectors. The monitored circuit may be wired as an NFPA Style B (Class B) or Style D (Class A) Initiating Device Cir- cuit. A 3.9 K Ohm End -of -Line Resistor (provided) terminates the end of the Style B or D (class B or A) circuit (maximum IDC loop resistance is 25 Ohms). Install ELR across termi- nals 8 and 9 for Style D application. NZM-100(A) OPERATION Each NZM-100(A) uses one of the available module addresses on an SLC loop. It responds to regular polls from the control panel and reports its type and the status (open/ normal/short) of its Initiating Device Circuit (IDC). A flashing LED indicates that the module is in communication with the control panel. The LED latches steady on alarm (subject to current limitations on the loop). NZM-100(A) SPECIFICATIONS Nominal operating voltage: 15 to 32 VDC. Maximum current draw: 5.1 mA (LED on). Maximum IDC wiring resistance: 25 Ohms. Average operating current: 270 NA, 1 communication and 1 LED flash every 5 seconds, 3.9k eol. EOL resistance: 3.9K Ohms. External supply voltage (between Terminals T10 and T11): • DC voltage: 24 volts power limited. • Ripple voltage: 0.1 Vrms maximum. • Current: 90 mA per module maximum. Temperature range: 32°F to 120°F (0°C to 49°C). Humidity range: 10% to 93% noncondensing. Dimensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x 1.25' (3.175 cm) deep. Mounts to a 4" (10.16 cm) square x 2.125' (5.398 cm) deep box. NDM-100(A) Dual Monitor Module The NDM-100(A) Dual Monitor Module is intended for use in intelligent, two -wire systems. It provides two independent two - wire initiating device circuits (IDCs) at two separate, consecutive addresses. It is capable of monitoring normally open contact fire alarm and supervisory devices. The module has a single panel - controlled LED. NOTE: The NDM-100(A) provides two Style B (Class B) IDC cir- cuits ONLY. Style D (Class A) IDC circuits are NOT supported in any application. NDM-100(A) SPECIFICATIONS Normal operating voltage range: 15 to 32 VDC. Maximum current draw: 6.4 mA (LED on). Average operating current: 750 pA (LED flashing). Maximum IDC wiring resistance: 1,500 Ohms. Maximum IDC Voltage: 11 Volts. Maximum IDC Current: 240 pA EOL resistance: 47K Ohms. Temperature range: 32° to 120°F (0° to 49°C). Humidity range: 10% to 93% (non -condensing). Dimensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x 1.25' (3.175 cm) deep. Mounts to a 4" (10.16 cm) square x 2.125' (5.398 cm) deep box. NDM-100(A) AUTOMATIC ADDRESSING The NDM-100(A) automatically assigns itself to two address- able points, starting with the original address. For example, if the NDM-100(A) is set to address "26", then it will automati- cally assign itself to addresses "26" and "27". NOTE: "Ones" addresses on the NDM-100(A) are 0, 2, 4, 6, or 8 only. Terminals 6 and 7 use the first address, and terminals 8 and 9 use the second address. QCAUTION: Avoid duplicating addresses on the system. Installation NMM-100(A), NZM-100(A), and NDM-100(A) modules mount directly to a standard 4" (10.16 cm) square, 2.125' (5.398 cm) deep, electrical box. They may also be mounted to the SMB500 surface -mount box. Mounting hardware and instal- lation instructions are provided with each module. All wiring must conform to applicable local codes, ordinances, and reg- ulations. These modules are intended for power -limited wir- ing only. The NMM-100P(A) module is intended to be wired and mounted without rigid connections inside a standard electri- cal box. All wiring must conform to applicable local codes, ordinances, and regulations. Agency Listings and Approvals In some cases, certain modules may not be listed by certain approval agencies, or listing may be in process. Consult fac- tory for latest listing status. • UL: S635. • ULC: S635. • FM Approved. • CSFM: 7300-0028:0230 (NMM-100, NMM-100P, NZM- 100); 7300-0028:0237 (NDM-100). • MEA: 72-01-E Vol. 2 (NMM-100, NMM-100P, NZM-100); 227-03-E Vol. 3 (NDM-100). Product Line Information NOTE: A" suffix indicates ULC -listed model. NMM-100(A): Monitor module. NMM-100P(A): Monitor module, miniature. NZM-100(A): Monitor module, two -wire detectors. NDM-100(A): Monitor module, dual, two independent Class B circuits. SMB500: Optional surface -mount backbox. NOTE: See installation instructions and refer to the SLC Wiring Manual, PN 52304. DN -6999:E • 07/30/2015 — Page 3 of 4 Notifier(@ and FireWarden® are registered trademarks and LiteSpeedT"" and FireWatchT" are trademarks of Honeywell International Inc. 02015 by Honeywell International Inc. All rights reserved. Unauthorized use of this document is strictly prohibited. 'SO 9oo1 This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. 6VGINEERIN6 8 MANUFACTURING QUALITY SYSTEMS All specifications are subject to change without notice. For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118. www.notifier.com Page 4 of 4 — DN -6999:E • 07/30/2015 SYSTEM SENSOR" Indoor Selectable - Output Strobes and Horn Strobes for Ceiling Applications System Sensor L -Series audible visible notification products are rich with features guaranteed to cut installation times and maximize profits with lower current draw and modern aesthetics. Features • Plug-in design with minimal intrusion into the back box • Tamper-resistant construction • Automatic selection of 12- or 24 -volt operation at 15 and 30 candela • Field -selectable candela settings on ceiling units: 15, 30, 75, 95, 115, 150, and 177 • Horn rated at 88+ dBA at 16 volts • Rotary switch for horn tone and two volume selections • Universal mounting plate for ceiling units • Mounting plate shorting spring feature checks wiring continuity before device installation • Electrically Compatible with legacy SpectrAlert and SpectrAlert Advance devices • Compatible with MDL3 sync module • Listed for ceiling mounting only Agency Listings SIGNALING APPfIDVED o . LISTED 55512 FM approveo except 71251653050-0 54011 for A -EAT models 71351653:0503 3657393 The System Sensor L -Series offers the most versatile and easy-to-use line of horns, strobes, and horn strobes in the industry with lower current draws and modern aesthetics. With white and red plastic housings, wall and ceiling mounting options,'System Sensor L -Series can meet virtually any application requirement. The entire L -Series product line of ceiling -mount strobes and horn strobes include a variety of features that increase their application versatility while simplifying installation. All devices feature a plug-in design with minimal intrusion into the back box, making installations fast and foolproof while virtually eliminating costly and time- consuming ground faults. To further simplify installation, the L -Series utilizes a universal mounting plate so installers can mount them to a wide array of back boxes. With an onboard shorting spring, installers can test wiring continuity before the device is installed. Installers can also easily adapt devices to a suit a wide range of application requirements using field -selectable candela settings, automatic selection of 12- or 24 -volt operation, and a rotary switch for horn tones with two volume selections. L -Series Specifications General L -Series ceiling -mount strobes and horn strobes shall mount to a standard 4 x 4 x 1Yz-inch back box, 4 -inch octagon back box, or double - gang back box. Two -wire products shall also mount to a single -gang 2 x 4 x 17/'8 -inch back box. A universal mounting plate shall be used for mounting ceiling and wall products. The notification appliance circuit wiring shall terminate at the universal mounting plate. Also, L -Series products, when used with the Sync•Circuif' Module accessory, shall be powered from a non -coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts. When used with the Sync•Circuit Module, 12 -volt -rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts; 24 -volt -rated notification appliance circuit outputs shall operate between 16.5 and 33 volts. Indoor L -Series products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC or full -wave rectified unfiltered power supply. Ceiling strobes and horn strobes shall have field -selectable candela settings including 15, 30, 75, 95, 115, 150, and 177. Strobe The strobe shall be a System Sensor L -Series Model listed to UL 1971 and shall be approved for fire protective service. The strobe shall be wired as a primary -signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances, flashing at 1 Hz over the strobe's entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system. Horn Strobe Combination The horn strobe shall be a System Sensor L -Series Model listed to UL 1971 and UL 464 and shall be approved for fire protective service. The horn strobe shall be wired as a primary -signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances, flashing at 1 Hz over the strobe's entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system. The horn shall have two audibility options and an option to switch between a temporal three pattern and a non -temporal (continuous) pattern. These options are set by a multiple position switch. The horn on horn strobe models shall operate on a coded or non -coded power supply. Synchronization Module The module shall be a System Sensor Sync -Circuit model MDL3 listed to UL 464 and shall be approved for fire protective service. The module shall synchronize L -Series strobes at 1 Hz and horns at temporal three. Also, while operating the strobes, the module shall silence the horns on horn strobe models over a single pair of wires. The module shall mount to a 4 11/16 x 4 11/16 x 2 1i8 -inch back box. The module shall also control two Style Y (class B) circuits or one Style Z (class A) circuit. The module shall synchronize multiple zones. Daisy chaining two or more synchronization modules together will synchronize all the zones they control. The module shall not operate on a coded power supply. Standard Operating Temperature 32°F to 120°F (0°C to 49°C) Humidity Range 10 to 93% non -condensing Strobe Flash Rate 1 flash per second Nominal Voltage Regulated 12 VDC or regulated 24 DC/FWR' Operating Voltage Rangel 8 to 17.5 V (12 V nominal) or 16 to 33 V (24 V nominal) Operating Voltage Range (MDL3) 8.5 to 17.5V (12 V nominal) or 16.5 to 33 V (24V nominal) Input Terminal Wire Gauge 12 to 18 AWG Ceiling -Mount Dimensions (including lens) 6.8" diameter x 2.5' high (173 mm diameter x 64 mm high) Ceiling -Mount Surface Mount Back Box Skirt Dimensions 6.9' diameter x 3.4' high (175 mm diameter x 86 mm high) (SBBCRL, SBBCWL) Notes: 1. Full Wave Rectified (FWR) voltage is a non-regulated, time -varying power source that is used on some power supply and panel outputs 2. P, S, PC, and SC products will operate at 12 V nominal only for 15 and 30 cd. AVD586800 UL Current Draw Data Candela 8-175 Volts DC 16-33 Volts DC FWR 15 87 41 60 30 153 63 86 75 N/A 111 142 95 NFA 134 164 115 N/A 158 191 150 N/A 189 228 177 N/A 226 264 8-17.5 Volts 16-33 Volts DC Input 15cd 30cd 15cd 89 30cd 75cd 95cd 115cd 150cd 177cd Temporal High 103 167 71 4 Non -Temporal 90 143 165 187 5 3.1 KHz Temporal 217 254 Temporal Low 96 165 54 76 71 137 161 185 84 211 249 Non -Temporal High 106 173 71 83 90 141 165 187 230 273 Non-Temportal Low 95 166 54 71 124 161 170 216 258 3.1 K Temporal High 111 164 69 94 147 163 184 229 257 3.1 K Temporal Low 103 163 54 88 143 155 185 212 252 3.1 K Non -Temporal High 111 172 69 94 144 164 202 229 271 3.1 K Non -Temporal Low 103 169 54 88 131 155 187 217 259 FWR Input 16-33 Volts 15cd 30cd 75cd 95cd 11 5c 150cd 177cd Temporal High 107 135 179 198 223 254 286 Temporal Low 78 101 151 172 199 229 262 Non -Temporal High 107 135 179 198 223 254 286 Non-Temportal Low 78 101 151 172 199 229 262 3.1 K Temporal High 108 135 179 200 225 255 289 3.1 K Temporal Low 79 101 150 171 196 229 260 3.1 K Non -Temporal High 108 135 179 200 225 255 289 3.1 K Non -Temporal Low 79 101 150 171 196 229 260 Horn Strobe Tones and Sound Output Data 8-175 16-33 Volts Volts Switch Position Sound Pattern dB DC DC FWR 1 Temporal High 84 89 89 2 Temporal Low 75 83 83 3 Non -Temporal High 85 90 90 4 Non -Temporal Low 76 84 84 5 3.1 KHz Temporal High 83 88 88 6 3.1 KHz Temporal Low 76 82 82 7 3.1 KHz Non -Temporal High 84 89 89 8 3.1 KHz Non -Temporal Low 77 83 83 AVDS86WO m SAFE SYSTEMS 421 S. PIERCE AVE LOUISVILLE, CO 80027 303-444-1191 BURGWY•FiRE•ACCESS CONTROL PROJECT: FA -7726 01/18/2018 WCCFA 11415 WEST 1-70 FRONTAGE RD NORTH WHEAT RIDGE, CO 80033 ENCLOSURES NFW-50 7707 NOT-BG12LX NP -100 NH -100 NMM-100 SYSTEM SENSOR HORN/STROBE BK-PC2WL BK-SCWL REVISION: NOI DATE BY: DESCRIPTION 1 101/18/181 MK I PERMIT SET Max SHOP DRAWING BY: MAX KARGARZADEH, SET NICET IV - FIRE ALARM CERT 101856; EXP. NOV. 1, 2018 299 MILWAUKEE ST. SUITE 222 DENVER, COLORADO 720-297-1563 cad80113@hotmail.com FireWarden-50(E) Intelligent Addressable FACP with Built -In Communicator General The NOTIFIER FireWarden-50 (NFW-50) is a Fire Alarm Con- trol Panel (FACP) and Digital Alarm Communicator/Transmitter (DACT) combined into one circuit board. This compact, intelli- gent addressable control panel supports up to 50 addressable devices in any combination of detectors or modules. With an extensive list of powerful features, the FireWarden-50 pro- grams just like FireWarden-100 products, yet fits into applica- tions previously served only by conventional panels. The FireWarden-50's integral DACT transmits system status (alarms, troubles, AC loss, etc.) to a Central Station via the public switched telephone network. It also allows remote and local programming of the control panel using the PS -Tools Upload/Download utility. In addition, the control panel may be programmed or interrogated off-site via the public switched telephone network. Any personal computer with WindowsT" 95 or greater, and compatible modem with a speed of 14.4 kbps or faster and Upload/Download software, may serve as a Ser- vice Terminal. This allows download of the entire program or upload of the entire program, history file, walk -test data, cur- rent status and system voltages. The power supply and all electronics are contained on a single circuit board supported on a new quick install chassis and housed in a metal cabinet. Available accessories include local and remote upload/download software, remote annunciators, and reverse polarity/city box transmitter. (4XTM) The FireWatch Series internet monitoring modules IPDACT-2 and IPDACT-2UD permit monitoring of alarm signals over the Internet, saving the monthly cost of two telephone lines. Although not required, the secondary telephone line may be retained providing backup communication over the public switched telephone line. NOTE: Unless otherwise specified, the term FireWarden-50 is used in this data sheet to refer to both the FireWarden-50 and the FireWarden-50E FACPs. For FireWarden-50C, refer to DN - 60446. Features • Listed to UL Standard 864, 9th edition. • Auto -program (learn mode) reduces installation time. Reports two devices set to the same address. • On -board DACT. • Two independently programmable Style Z (Class A) or Style Y (Class B) NAC circuits. • Selectable strobe synchronization for System Sensor, Wheelock, and Gentex devices. • Remote Acknowledge, Silence, Reset and Drill via address- able monitor modules. • Two programmable relays and one fixed trouble relay. • Built-in Programmer. • Telephone Line Active LEDs. • EIA -232 PC interface. • Integral 80 -character LCD display with backlighting. • Real-time clock/calendar with automatic daylight savings control. • History file with 500 event capacity. • Automatic detector sensitivity testing (NFPA 72 compliant). • Automatic device type -code verification. DN -7102:E NOTIFIER° by Honeywell • Point trouble identification. • Waterflow selection per module point. • Alarm verification selection per detector point. • Maintenance alert warns when smoke detector dust accu- mulation is excessive. • One-person audible or silent walk test with walk -test log and printout. • System alarm verification selection per detector point. • PAS (Positive Alarm Sequence) and Pre -signal per point (NFPA 72 compliant). • Up to eight ANN -BUS annunciators • Remote Acknowledge, Alarm Silence, Reset and Drill via addressable modules or remote annunciator. • Upload/Download (local or remote) of program and data via integral DACT. SLC COMMUNICATION LOOP • Single addressable SLC loop which meets NFPA Style 4, 6 and 7 requirements. • 50 addressable device capacity (any combination of addressable detectors and modules). • Compatible with NOTIFIER FireWarden addressable devices (refer to the FireWarden SLC Wiring Manuan. NOTIFICATION APPLIANCE CIRCUITS (NA CS) • Two independently programmable output circuits. Circuits can be configured for the following outputs: — Style Y (Class B) — Style Z (Class A) — Door Holder Service (cannot be used for notification appliances) — AUX Power Source (cannot be used for notification appliances) • Silence Inhibit and Autosilence timer options. • Continuous, March Time, Temporal or California code for main circuit board NACs with two-stage capability. • Selectable strobe synchronization per NAC. • 2.5 A total power for NACs. NOTE: Maximum or total 24VDC system power shared between all NAC circuits and the ANN -BUS is 2.7 A. DN -7102:E • 02/22/2011 — Page 1 of 4 INSPECTION RECORD Inspection online form: http://www.ci.wheatridge.co.us/inspection Cancellations must be submitted via the online form before 8 a.m. the day of the inspection Inspections will not be performed unless this card is posted on the project site Request an inspection before MIDNIGHT (11:59 PM) to receive an inspection the following business day PERMff:,9-0 ' 62 CADDRESS: JOB CODE: Foundation Inspections Date Inspector Initials Comments 102 Caissons / Piers f .17 103 Footing / P.E. Letter 104 Foundation Setback Cert. 105 Stem Walls r ►� ,, 106 Foundation wall Insulation Do Not Pour Concrete Prior To Approval Of The Above Inspections Underground / Slab Inspections Date Inspector Initials Comments 201 Electrical / Cable/ Conduit f .17 202 Sewer Underground Int. 203 Sewer Underground Ext. 204 Plumbing Underground Int. r ►� ,, 205 Plumbing Underground Ext. 206 Water Underground Do Not Cover Underground or Below / In -Slab Work Prior To Approval Of The Above Inspections Rough Inspection Date inspector Initials Comments 301 Rough Framing f .17 302 Wall Sheathing 303 Roof Sheathing 304 Sheer Inspection 305 Insulation 306 Mid -Roof 307 Metal / Lath / Stucco 308 Rough Electrical Residential 309 Rough Electrical Commercial 310 Electrical Meter Residential 311 Electrical Meter Commercial 312 Temp. Const. Meter 313 Rough Plumbing Residential 314 Rough Plumbing Commercial y .� 315 Shower Pan SEE OVER FOR ADDITIONAL INSPECTIONS PERMIT:`/ ADDRESS: [/t-j/S Z& I "-70 JOB CODE: r -;A. -ti, 1,"0 Rough Inspection (continued) Date Inspector Initials U Comments 316 Rough Mechanical Residential 1 317 Rough Mechanical Commercial �r r/ 318 Boiler / Furnace 319 Hot water tank 320 Drywall screw and Nail 321 Moisture board / shower walls ♦ i -; 322 Rough Grading 323 Miscellaneous v Final Inspections Date Inspector I 'tial Comments 402 Gas Meter Release6- 1 403 Final Electrical Residential 404 Final Electrical Commercial 405 Final Mechanical Residential 406 Final Mechanical Commercial '-61 A -; 407 Final Plumbing Residential 408 Final Plumbing Commercial v 409 Final Roof 410 Final Window/Door 411 Landscape/Park/Planning* Inspections from these entities shall be requested one week in advance. *For landscaping and parking inspections please call 303-235-2846 **For ROW and drainage inspections please call 303-235-2861 ***For fire inspections please contact the Fire Protection District for your project. 412 Row/Drainage/Public Works** 413 Flood plain Inspection** 414 Fire Insp. / Fire Protection*** 415 Public Works Final** 416 Storm Water Mgmt.** 417 Zoning Final Inspection* 418 Building Final Inspection >97, A ' Note: All items must be completed and approved by Planning, Public Works, Fire and Building before a Certificate of Occupancy is issued. Approval of the Final Building Inspection does not constitute authorization of occupancy. For Low Voltage permits please be sure that rough inspections are completed by the Fire District and Electrical low voltage by the Building Division. 12/13/2017 MobileEyes Arvada Fire Protection District Address: Occupant Name: Contractor: Inspections Required: Community Risk Reduction Division 7903 Allison Way • Arvada,. CO 80005 Main 303-424-3012 • Fax 303-432-7995 www.arvadafire.com 11415 West Interstate 70 Frontage Road Wheat Ridge, CO 80033 Western Center for the Conservation of Fine Arts Mike Mueller, Owner Five Star Contracting, LLC (303) 888-2968 Tenant Finish/Remodel Job Number: 17-339 Permit Number: 17-339 Permit Issued On: 12/13/2017 Permit Expires On: 12/13/2018 ARVADA FIRE PERMIT - TENANT FINISH / REMODEL TO REQUEST INSPECTIONS, CALL (303) 424-3012 AND ASK FOR THE ASSIGNED PLAN REVIEWER LISTED ON THE PLAN REVIEW REPORT. DESCRIPTION INSP #1 INSP #2 INSP #3 INSP #4 PASS FAIL PASS FAIL PASS FAIL PASS FAIL Tenant Finish/Remodel PERMIT COMPLETE AFPD INSPECTOR SIGNATURE): ' DATE: / r / NOTICE TO CONT • Inspection request must be called in 24-48 hours before the desired inspection date. Inspections will be scheduled based on individual inspector availability. • NO inspections will occur without Fire District approved plans or comments available on-site. • Additional requirements not indicated on this card may be necessary -refer to approved plans and comment letter. • Work shall be in compliance with approved plans. Work not in compliance or that does not meet minimum standards may require additional inspections. • Failed inspections may require additional fees for re -inspection. • Inspections may reveal corrections necessary to bring work into compliance with applicable codes and standards. • Building FINAL inspection and approval is necessary prior to occupancy. • Post this record in a conspicuous place. • Loss or destruction of this card will require replacement and may require additional fees. p://www.mobile-eyes.com/MobileEyes3/TrackPermits_BasicPermit.asp?PID=1916&PPID=1922 1/1 i CITY OF WHEAT RIDGE Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: 5 6) % A L Ci Job Address: I tl1h Lj/ T-;70 (-onl�Gr ✓i% �� Permit Number: Wigoo?-ey ❑ No one available for inspection: Time) G7 AM/PM - , 15, Re -Inspection required: Yes o When corrections have been made, call for re -inspection at 303-234-5933 Date: Inspector: 0 DO NOT REMOVE THIS NOTICE INSPECTION RECORD Inspection online form: http://www.ci.wheatridge.co.us/inspection Cancellations must be submitted via the online form before 8 a.m. the day of the inspection Inspections will not be performed unless this card is posted on the project site Request an inspection before MIDNIGHT (11:59 PM) to receive an inspection the following b u�sintes day PERMIT:Z I i - 7 ADDRESS: j 1 �/ �� %J T-7 Q F"t "JO CODE: Foundation Inspections Date Inspector Initials Comments 102 Caissons / Piers 201 Electrical / Cable/ Conduit 103 Footing / P.E. Letter �._.. 104 Foundation Setback Cert. 105 Stem Walls 106 Foundation wall Insulation 204 Plumbing Underground Int. Do Not Pour Concrete Prior To Approval Of The Above Inspections Underground / Slab Inspections Date Inspector Initials Comments 201 Electrical / Cable/ Conduit 202 Sewer Underground Int. 203 Sewer Underground Ext. 204 Plumbing Underground Int. 205 Plumbing Underground Ext. 12,06 "v'aiCi vi,dergrouod Do Not Cover Underground or Below / In -Slab Work Prior To Approval Of The Above Inspections Rough Inspection Date Inspector Initials Comments 301 Rough Framing 302 Wall Sheathing 303 Roof Sheathing 304 Sheer Inspection 305 Insulation 306 Mid -Roof 307 Metal / Lath / Stucco 308 Rough Electrical Residential 309 Rough Electrical Commercial 310 Electrical Meter Residential 311 Electrical Meter Commercial 312 Temp. Const. Meter 313 Rough Plumbing Residential 314 Rough Plumbing Commercial 315 Shower Pan SEE OVER FOR ADDITIONAL INSPECTIONS A')/'�-f) 6- q Rough Inspection (continued) Date Inspector Initials Comments 316 Rough Mechanical Residential 317 Rough Mechanical Commercial ✓> �, , 318 Boiler / Furnace 404 Final Electrical Commercial 319 Hot water tank 405 Final Mechanical Residential 320 Drywall screw and Nail 406 Final Mechanical Commercial 321 Moisture board / shower walls 407 Final Plumbing Residential 322 Rough Grading 408 Final Plumbing Commercial 323 Miscellaneous 409 Final Roof Final Inspections Date Inspector I itials Comments 402 Gas Meter Release- 403 Final Electrical Residential 404 Final Electrical Commercial 405 Final Mechanical Residential 406 Final Mechanical Commercial 407 Final Plumbing Residential 408 Final Plumbing Commercial 409 Final Roof 410 Final Window/Door [ElLandscape/Park/Planning Inspections from these entities shall be requested one week in advance. For landscaping and parking inspections please call 303-235-2846 For ROW and drainage inspections please call 303-235-2861 For fire inspections please contact the Fire Protection District for your project. 14 ,,2 Row/ UrainageiPut)iiu Works ' 413 Flood plain Inspection 414 Fire Insp. / Fire Protection 415 Public Works Final 416 Storm Water Mgmt. 417 Zoning Final Inspection 418 Building twff Note: All items must be completed and approved by Planning, Public Works, Fire and Building before a Certificate of Occupancy is issued. Approval of the Final Building Inspection does not constitute authorization of occupancy. For Low Voltage permits please be sure that rough inspections are completed by the Fire District and Electrical low voltage by the Building Division. VOLT Q 7 # OF DEVICES NOTIFICATION DEVICE ALARMo��1 CURRENT v AS' e ! CURRENT 2 P2R 95cd (.165) 33 .082 ALM. NFW-50 1 1 P2R 75cd (.143) .143 SR 75cd {.111} .111 .00423 NH100 NAC 1 TOTAL CURRENT .473 120' 16 1. 5.08 120.4 16 # OF PUBLIC MODE NOTIFICATION Circuit Circuit Distance Volts at End Voltage Percent Current I I Device Drop Drop 1 1 .473 1 120 1 19-82 1 4.58 1 2% ALARM DEVICES NOTIFICATION DEVICE CURRENT. �HORN� {STROBE{ F�UPV V. � UX� I I I I ! CURRENT 2 SR 15cd .041 .082 ALM. NFW-50 1 .120 ,200 1 SR 75cd {.111} .111 .00423 NH100 1 .0003 .0003 NAC 2 TOTAL CURRENT .193 105 16 1 5.08 1 20.4 16 PUBLIC MODE NOTIFICATION Circuit Circuit Distance Volts at End Voltage Percent Current I I Device Drop Drop 2 .193 1 105 1 20.19 0.21 1% BATTERY CALCULATION DEVICE SYSTEM OUTPUTS DEVICE �HORN� {STROBE{ F�UPV V. � UX� I I I I ! CURRENT 1 1 121 1 1 1 STBY. ALM. NFW-50 1 .120 ,200 BG12LX 2 .00023 .00423 NH100 1 .0003 .0003 NP100 9 .0003 .0003 NMM100 1 .0045 .0005 NAC 2 NAC 1 44 # OF DEVICES STANDBY CURRENT .120 .00046 .0003 .0427 .0005 TOTAL CURRENT .12396 24 HRS. (STBY TIME) 24 X .12396 = 2.98 AH 5 MIN. (ALM TIME) .084 X .87 = .08 AH BATTERY REQUIRED 2.98 + .08 .� 3.06 AH END -LIFE FACTOR 3.06 X 1.2 =3.672 AH MINIMUM BATTERY SIZE FOR 24 HOURS BACKUP = 8 AH USE 2 12V - 8AH BATTERIES IN SERIES FOR 24V - 8AH Z D-12 2 D_11 c D-10 95CD 75CD 95CD 2 D-09 15CD 15CD 75CD ?, 'o' --'o'-----'ow Dw �W Ud-3 D-07 F $ D-06 ALARM CURRENT .200 .00046 .0003 .0027 .0005 .473 .193, .87 FORMULA USED E=1R(2L/1000) E -VOLTAGE DROP IN VOLTS I=CIRCUIT CURRENT IN AMPS R =RESISTANCE (FROM TABLE) L -LENGTH OF WIRE IN FEET WIRE RESISTANCE BASED ON NEC CH. 9 # SOLID UNCOATED CONDUCTORS. t })}-----�- - SAFE SYSTEMS UL CENTRAL D-05 STATION Z D-04 NAC';1 NAC 2 p M-02 CLASS B STYLE Y P M-01 Ll N FW -50 mm M-03 FACP AES 77'07 LISTED SLC DATA DATA ENCLOSURE CLASS B STYLE 4 �._.�_.. 1 { 12VAC I 1 TROUBLE ! I I I { II ! 12V-8AH 12V -SAH 12V-12AH 120 VAC PRIMARY POWER N FLOOR PLAN +o 1 1 -1 z a s 6 SHOP DRAWING NOTESk*44 PROJECT NAME. WCCFA CONTRACTOR: SAFE SYSTEMS PROJECT ADDRESS. 11415 WEST I-70 FRONTAGE RD NORTH ADDRESS: 421 S. PIERCE AVE WHEAT RIDGE, CO 80033 LOUISVILLE, CO 80027 PHONE NUMBER: 303-444-1191 APP ipVAL ARVADA FIRE PROTECTION DISTRICT AGENCY: 7903 ALLISON WAY, ARVADA, CO 80005 SYSTEM REQUIRE: NO (VOLUNTARY) PHONE NUMBER: 303-424-3012 BUILDING DATA: EXISTING (TENANT FINISH N0. 0F STORIES: ONE OCCUPANCY: B WORK AREA SF: 31380 SPRINKLER: NO IONS TYPE:iII-B Z STANbARDS. 2012 IFC, INTERNATIONAL FIRE CODE � 2012 16C, INTERNATIONAL BLDG CODE 0 2016 NFPA 72, NATIONAL FIRE ALARM CODE Z 2017 NFPA 70, NATIONAL ELECTRICAL CODE. . I -OM PROJECT SCOPE:(TENANT FINISH) Z � O� INSTALL 1 NEW FIRE ALARM CONTROL PANEL & 1 RF CENTRAL STATION COMMUNICATOR(AES-7707) W W � INSTALL 2 MANUAL PULL BOX.INSTALL 9 SMOKE DETECTORS AND 1 HEAT DETECTOR. INSTALL 3 � (' HORN=STROBES AND 3 STROBES. INSTALL 1 MONITOR MODULE TO SIGNAL TROUBLE UPON COMMUNICATOR j Q 0 FAULT. i-- Li. O Z W u V CL 0 V NOTIFICATION APPLIANCE CIRCUITS /DEVICES. NOTIFICATION CIRCUITS ARE SUPERVISED (CLASS B) AND U-' POWER -LIMITED. COMBINATION HORN -STROBES WILL PRODUCE THE ANSI 53.41 AUDIBLE EMERGENCY � V> 2 L.L � EVACUATION SIGNAL (TEMPORAL CODING). NOTIFICATION DEVICES WILL BE SYNCHRONIZED.. WIRING METHOD: WIRING METHOD TO LOW VOLTAGE CIRCUITS WILL COMPLY WITH NATIONAL ELECTRICALj- CODE, ARTICLE 760 AND RELATED ARTICLES, FOR FIRE PROTECTIVE POWER LIMITED CIRCUITS. Z _ Q WIRE.. TYPE; WIRE TO POWER LIMITED NAC CIRCUITS: #16AWG, 2 OR 4 CONDUCTOR ,FIRE PROTECTIVE POWER Z � w LIMITED PLENUM CABLE (TYPE FPLP) -SLC CIRCUITS: #18 AWG )MINIMUM), 2 OR 4 CONDUCTOR, FIRE W � PROTECTIVE POWER LIMITED PLENUM CABLE (TYPE FPLP). WIRE IN NON -PLENUM AREAS MAY BE TYPE FPL OR � W j FPLR, 3: LO KEY SYMBOL SYSTEM OUTPUTS FRCP I �HORN� {STROBE{ F�UPV V. � UX� I I I I ! STA. 1 1 121 1 1 1 1 N/A I 1 I 1 l l 1 1 I ! l I I I ! 1 1 ! I 1 ! 1 I I i C1 I Zi V)l ! I I !�!�„oi! 1 ! N/A I� 1 I IU -i !.Q I W1 Q I !��. lJ1.....�tZI._.{IZI 1 I I I lei I <1 V)I L1 I I #BIZ!©I�l_{1,I ! .1�I�ILn <17)1 lW1! I 1�I4wI I l�1�1�1 i ! IZIU..�1Uo1 I I 161 _..._ I:z ! U,r{ ! � I . i IZILnIwjI_jIL?I>I ! >„ I � I 1 I{�# I ! I ! I ! I I !>l i1 LnI ii I I m1<11.c�#tyI�I01�1t1 izlZ# # !{�1�1�I I I I I I 1 ImI<I--IC)I=I�I ILDI, �ILnI�---IoIL! IC)) 1 I I#:..ICDI # IU"I 1�I�ILnI I I Itni IwI�{Icn1w1 I 1�I�IJI>I__jI C131=lco 1,,, 1�I I l;=?I<I I I jI I ILm11CDI I I 10lN1�I 1 1 I=1M l 1�CIaICD1oI�!©1 SEQUENCEOF OPERATION i--Ii�IQI�I�I u..1 { i�l�-1 ! Irll # I_,..,�I1�1 ! I IM101�1 i 1 f "�t 1 < 1 �""" 1 # c,,ry I l INPUT %OUTPUT MATRIX I ! 1 I I I I ! Z 1 Z ! i IWIwI I ! � 1 c,� # � 1 i 1 I /)I >I JI I I I ! ..� # _.,..� ! J 1.J { ...._i I {w{w{w{w#w{w{ I m# J 1 I {IcnI I I m I= I col I I I= UJIMI I I 1,<1<1<1<1Q1,<1 1c 10..1 1a.1�1�1 I'�I-I I 1< > 1 I �I �I =I I I I,�1�II I i SYSTEM INPUTS 1! i I!!!!! MONITOR MODULE 1 ------............_4_.{.__1.A-4---I--I--{--4-�-4---1---4--4--+--�---{-�- Q NMM-100 MANUAL PULL BOX i1I i i 1 1 w�. SMOKE DETECTOR/HEAT DETECTOR!}! .pn�1 _ rn _ _ �.- _ _ .t.! .rim _ _ _ r _ _ _ wr• _ _ _ _ _ _ _ _ Fr _ s� 11.w+'++� �� T 101_01 1 101 11_ 1 _1 1 _w�w w..�a� -�• '�� '^"�" �"�'�' �'-'�''�'� 4 MOTIF APP) CKT_FAULT CIRC)JIT, HEAT DETECTOR 1 A � AC POWER FAIL._r__.�____________�._�_�._,�_{�.�,�.�_.�_�.,�_�_.�_�...�_!_.�-�.-�.- 1401 OPEN CIRCUIT FAULT II I�#�# 1t jI GROUND CIRCUIT FAULT 1 ! i[ I 1 I� 1 �1 y SYSTEM LOW BATTERY ! 11I l I SUPERVISING STATION COMM FAULT I I I !! I ��`t1 r!t_arw SYMBOL DEVICE QTY BOX FIRE ALARM CONTROL PANEL FCP D W 1 N/A (NFW-50) U) > O RF COMMUNICATOR 1 N/A 7707 00 Two Elp MANUAL PULL BOX 2 N/A Q NOT-BG12LX � I -CD SYSTEM SENSOR 3 A STROBE U) } W W SMOKE DETECTOR 9 A NP -10}0 J 'off HORNISTOBE 3 N/A Mn� MONITOR MODULE 1 N/A Q NMM-100 (n co (DF HEAT DETECTOR 1 A � NH -100 REVISION: N0. DATE BY: DESCRIPTION 1 1/19/16 MK PERMIT SE' SHOP DRAWING BY: �NeaKaW Max Max ll�� MAX KARGARZADEH, SET NICET IV - FIRE ALARM CERT 101856 EXP. NOV. 11 2018 1492 E DARTMOUTH AVE ENGLEWOOD, COLORADO 720-297-1563 cad80113(alhotmail.com SCALE: I SHEET: It 1 10 1/8 = 1 -0 1 OF 1 W N O U) > cD 00 Two W W Q 0) -. � I -CD F- a U) } W W � F- CL J C:) W LL uj J M O Q (n co � � N � d' 0 J REVISION: N0. DATE BY: DESCRIPTION 1 1/19/16 MK PERMIT SE' SHOP DRAWING BY: �NeaKaW Max Max ll�� MAX KARGARZADEH, SET NICET IV - FIRE ALARM CERT 101856 EXP. NOV. 11 2018 1492 E DARTMOUTH AVE ENGLEWOOD, COLORADO 720-297-1563 cad80113(alhotmail.com SCALE: I SHEET: It 1 10 1/8 = 1 -0 1 OF 1 i CITY OF WHEAT RIDGE _:�9rBuilding Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax I NSP ECTI O NC NOTICE qC)Inspection Type: r Job Address: I y1 4/ - 7 0 Iric,nJA /W Permit Number: ❑ No one available for inspection-ime_ AM/PM Re -Inspection required: Yes 60) When corrections have been made, call for re -inspection at 303-234-5933 Date: 1g Inspector: Y4TP DO NOT REMOVE THIS NOTICE i CITY OF WHEAT RIDGE Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE __ ll. 1 e� Ala' Memel � Inspection Type: G�,� Job Address: IZ11Q. Permit Number: 70Y v® ❑ No one available for inspection: Time _D AM/QPM Re -Inspection required: Yes `No When corrections have been made, call for re -inspection at 303 -234 - Date: 1 ,--6— Inspector: � `��• % "-¢— DO NOT REMOVE THIS NOTICE e&�L. i CITY OF WHEAT RIDG Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax 1 INSPECTION NOTICE Inspection Type: 3 $C �"//O/ Job Address: i Permit Number: ❑ No one available for inspection: Time ff '.) Re -Inspection required: Yes �No� When corrections have been made, call for re -inspection at 303-234-5933 Date:41 • -inspector:.1t�tJ DO NOT REMOVE THIS NOTICE i CITY OF WHEAT RIDGE Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: 3��e'y�'�� 1 Job Address: f/��5l� 7e F � Permit Number: cid/ _20 ❑ No one available for inspection: Time c,"J� _) AM/PM Re -Inspection required: Yes/ No When corrections have been made, cairn re -inspection at 303-234-5933 Date: % • 9 , IF Inspector: ,,�71 4 --- DO NOT REMOVE THIS NOTICE i CITY OF WHEAT RIDGE Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: _ �� y/ ��►� bpi'/ c(g/1 Job Address: Ilei/S W X70 /L/ Al Permit Number: QC/7�FSS 20 ❑ No one available for inspection: Time // `K)I% 30M _ Re -Inspection required: Yes No )/ When corrections have been made, call for re -inspection at 303-234-5933 Date: 4 '9, /7 Inspector: JeAIr7,1/ DO NOT NOT REMOVE THIS NOTICE i CITY OF WHEAT RIDGE Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office - (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: 3 IF/ 1,\116C h • %'Gc9ll Job Address: ll yu 0)77- % Permit Number: PO/ 70 e&,Po ❑ No one available for inspection: -Time AV/PM Re -Inspection required: Yes ( No�=' When corrections have been made, call for re -inspection at 303-234-5933 Date: /-�' SV- /% Inspector: Jew r,11-,,4,r4- DO4-- DO NOT REMOVE THIS NOTICE i CITY OF WHEAT RIDGE Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: 3o ol A E�G Job Address: T'% 7",,,1 )9,/)e i{ d Permit Number: ';�t-jl708 690 ❑ No one available for inspectDrNo ime l AM/PM Re -Inspection required: Yes *When corrections have been made, c�rre--iin-spection at 303-234-5933 Date:) d1l % Inspector: DO NOT REMOVE THIS NOTICE i CITY OF WHEAT RIDGE Building Inspection Division (303) 234-5933 Inspection line (303) 235-2855 Office • (303) 237-8929 Fax INSPECTION NOTICE Inspection Type: ;)C)ql Job Address: D Permit Number: w . -' 1X;1. T Of 0 ❑ No one available for inspection: Time Re -Inspection required: Yes�`!o?_._ When corrections have been made, call for re -inspection at 303-234-5933 Date: %' %c� % ^% Inspector: DO NOT REMOVE THIS NOTICE City of Wheat Ridge Comm. Tenant Finish PERMIT - 201708620 PERMIT NO: 201708620 ISSUED: 12/07/2017 JOB ADDRESS: 11415 W I-70 Frontage RD N EXPIRES: 12/07/2018 JOB DESCRIPTION: Commercial Tenant Improvement: remodel of 3380 SF including new ADA restroom. Mechanical, Electrical and plumbing, including Remove and replace 2 furnaces,80K BTU. New Scope: Adding RTU on concrete pad behind building. (requires planning) *** CONTACTS *** OWNER (303)423-9700 SIX OAK LIMITED PARTNERSHIP SUB (303)888-2968 Mike Mueller 090040 Five Star Contracting LLC SUB (303)587-2049 Juell Seidel 110222 Seidel Electric LLC SUB (303)995-0486 Randy Lane 021507 R n R Plumbing, Inc. SUB (303)423-7905 Timothy Bartels 017674 B & B Heating & A/C *** PARCEL INFO *** ZONE CODE: UA / Unassigned USE: UA / Unassigned SUBDIVISION CODE: 420 / Storage Warehouse; 0 BLOCK/LOT#: 0 / *** FEE SUMMARY *** ESTIMATED PROJECT VALUATION: 74,000.00 FEES Total Valuation 0.00 Plan_ Review Fee 599.79 Use Tax 1,554.00 Permit Fee 922.75 ** TOTAL ** 3,076.54 *** COMMENTS *** *** CONDITIONS *** All roughs to be done at Framing Inspection. Approved per plans and red -line notes on plans. Must comply with 2012 IBC, 2014 NEC and all applicable City of Wheat Ridge Municipal Codes. Work is subject to field inspections. **Prior to final inspection approval - As-builts are required before approval of the Building Final Inspection and Certificate of Occupancy can be issued. City of Wheat Ridge Comm. Tenant Finish PERMIT - 201708620 PERMIT NO: 201708620 ISSUED: 12/07/2017 JOB ADDRESS: 11415 W I-70 Frontage RD N EXPIRES: 12/07/2018 JOB DESCRIPTION: Commercial Tenant Improvement: remodel of 3380 SF including new ADA restroom. Mechanical, Electrical and plumbing, including Remove and replace 2 furnaces,80K BTU. New Scope: Adding RTU on concrete pad behind building. (requires planning) I, by in signature, do hereby attest that the work to be performed shall comply with all accompanying approved plans and specifications, applicable building codes, an 1 applicable r,ez� 'al codes, policies and procedures, and that I am a legal owner or have been authorized by the legal owner of th ope and m a to obtain this permit and perform the work described and approved in conjunction with this�pperre I rth a ga ed to include all entities named within this document as parties to the work to be pertCr erf a disclosed in this documet and/or its' accompanying approved plans and specifications. Sig ure of OWNER CONTRACTOR (Circle one) Date 1. This permit was issued ba €®rntation provided in the permit application and accompanying plans and specifications and is subject to the compliance with thos documents, and all applicable statutes, ordinances, regulations, policies and procedures. 2. This permit shall expire 365 days after the date of issuance regardless of activity. Requests for extension must be made in writing and received prior to the date of expiration. An extension of no more than 180 days made be granted at the discretion of the Chief Building Official and may be subject to a fee equal to one-half of the original permit fee. 3. If this permit expires, a new permit may be required to be obtained. Issuance of a new permit shall be subject to the standard requirements, fees and procedures for approval of any new permit. Re -issuance or extension of expired permits is at the sole discretion of the Chief Building Offiial and is not guaranteed. 4' No work of any manner shall be performed that shall results in a changeof the natural flow of water without prior and specific approval. 5. The permit holder shall notify the Building and Inspection Services Division in accordance with established policy of all required inspections and shall not proceed or conceal work without written approval of such work from the Building and Inspection Services Division. 6. The issuance or granting of a permit shall not be construed to be a permit for, or an approval of, an violation of any provision of any applicabl de or any ordinance or regulation of this jurisdiction. Approval of work is subject to field inspection. Signature of Chief Building Official Date REQUESTS MUST BE MADE BY 11:59PM ANY BUSINESS DAY FOR INSPECTION THE FOLLOWING BUSINESS DAY. FOR OFFICE USE ONLY I ( ity a)l Date: / U /�/Z& J/ 7 W heat. I��jcl�e l/ Plan/Permit # in5 `' & Inspection Services Division _11 o4o 2 W. 291h Ave., Wheat Ridge, CO 80033 Plan Review Fee: ;e: 303-235-2855 * Fax: 303-237-8929 �( pection Line: 303-234-5933 Building Permit Application **` Please complete all highlighted areas on both sides of this form. Incomplete applications may not be processed.'""' Property Address: ( (`i I rl W, —1--70 Fro waq e _K(j- N o r Property Owner (please print): {mac]� L, '� 3 `j -7M Property Owner Email: K'kf VJz\kLIJV2 C", Ccrt-jCC�S-f-. Y1C:J Mailing Address: (if different than property address) Address: i � ` 15 7 V %� Rpt • �J o r � �"1 City, state, zip: ArchitectlEnaineer: M+ C V1 CkC_ A M a C" ( L( C Architect/Engineer E-mail: ►Y�i Ise �e 4zr'cc��c�r (- Cr}�phone�0 �> $ 6 �- oZ`�(r, Fye si-ar- CooJrckch'vi(� L_L"C Contractors City License #: C' q co, 1-{ 0 � Phone:G C') Z,3(3, 62 Contractor E-mail Address: R1t k i J'e cs. `� r- C C} @ 0.o L . C Sub Contractors:(( Electrical: S 2' J�1 � �-/1 C Plumbing: ' tet' Mechanical: W.R. City License # 110 221. --' W.R. City License # (5;� -- 1507 W.R. City License # 1.7 Lf Other City Licensed Sub: Other City Licensed Sub: City License # City License # Complete all information on BOTH sides of this form � City of �KWheatjk dge COMMUNITY DEVELOPMENT Building & Inspection Services Division 7500 W. 29th Ave., Wheat Ridge, CO 80033 Office: 303-235-2855 * Fax: 303-237-8929 Inspection Line: 303-234-5933 Email: permits(cD-ci.wheatridge.co.us Building Perm i Revision/A endment Application *** Please complete all highlighted areas on both sYdes of this form. Incomplete applications may not be processed. **" FOR OFFICE USE ONLY Date: Add to Permit # Property Address: Property Owner (please print): Sji X n., i t l n,, �, j 1� f LAC,, I Al o Phone:3b 3 2 3 9 7 d e Property Owner Email: Mailing Address: (if different than property address) Address City, State, Zip: Contact Person: Ak �g ��+ 11,4 r Phonve: Contractor: WK80sallm Contractors City License #: 6-q0 q (� t� v Phone:�3C�Z *ft L -S 6 J' Contractor E-mail Address: i /GP_ Al r. t, 6, Cid L r o —/],. Please Note: Additional valuation must include all general and subcontracted work to be performed related to the revisions and/or amendments declared in the description of work and which were not included in the original permit valuation. If revisions or amendments increase the original valuation, additional fees will be due at the time of approval. Depending on the scope of work, additional plan review fees may be due upon approval ($60.00 an hour — 2 hour minimum). Description of revised/amended work: J h S tic ll 0. qG41) Ci -d c- 30ta) CFM 19-J, - J AkL ✓JL ldt V Sq. Ft./LF Amps q&10)66 -Ricc tl► 1c� � p a , Btu's Squares 3JOO c---F-M 1�-(' u o" c� c.Or, c n + p" cA Gallons Other Additional Project Value: (Must include all general and subcontracted work to be performed related to revisions/amendments described above) OWNER/CONTRACTOR SIGNATURE OF UNDERSTANDING AND AGREEMENT I hereby certify that the setback distances proposed by this permit application are accurate and do not violate applicable ordinances, rules or regulations of the City of Wheat Ridge or covenants, easements or restrictions of record; that all measurements shown and allegations made are accurate; that I have read and agree to abide by all conditions printed on this application and that I assume full responsibility for compliance with applicable City of Wheat Ridge codes and ordinances for work under any permit issued based on this application; that I am the legal owner or have been authorized by the legal owner of the property to perform the described work and am also authorized by the legal owner of any entity included on this application to list that entity on this application. CIRCLE ONE: (OWNER) (CONTRACTOR) or: (AUTHORIZED R SE T V of ( R) (CONTRACTOR) PRINT NAME: / "l (! //'(GLC G� SIGP4T'IIJ ATE: `26 C'�1117 ZONING COMMMENTS: Reviewer: BUILDING DEPARTMENT COMMENTS: Reviewer: PUBLIC WORKS COMMENTS: Reviewer: DEPARTMENT USE ONLY b " 5 OCC -1. OCCUPANCY CLASSIFICATION -1 6 OC PROOF OF SUBMISSION FORMS Fire Department ❑ Received ❑ Not Required Water District ❑ Received ❑ Not Required Sanitation District ❑ Received ❑ Not Required Building Division Valuation: $ 1 + (s� 1 avC� tion of work: (Check all that apply) j NEW COMMERCIAL STRUCTURE ❑ ELECTRICAL SERVICE UPGRADE J NEW RESIDENTIAL STRUCTURE ❑ COMMERCIAL ROOFING ❑ COMMERCIAL ADDITION ❑ RESIDENTIAL ROOFING ❑ RESDENTIAL ADDITION ❑ WINDOW REPLACEMENT ❑ COMMERCIAL ACCESSORY STRUCTURE (Garage, shed, deck, etc.) ❑ RESIDENTIAL ACCESSORY STRUCTURE (Garage, shed, deck, etc.) ❑ MECHANICAL SYSTEM/APPLIANCE REPAIR or REPLACEMENT ❑ PLUMBING SYSTEM/APPLIANCE REPAIR or REPLACMENT ❑ ELECTRICAL SYSTgWIPPLIANCE PAIR or REPLACEMENT THEA (Describe) rr „ J, (For ALL projects, please provide a detatle description of work to be performed, Including current use of areas, proposed uses, square footage, existing condition and proposed new condition, appliance size and efficiency, amount of materials to be used, etc. add Acw e y type and t v., ( I a d c4 ct u�✓j CeJ "m c c ,M (� i F ck Z tic�� r �u J,� Q( 4m., t!/, lu P {ids nn 0.1 WeA id1G, tl C.Qri. p c_.l-c oa ( tiu"i rrl- mai w<ti// aCio� S/F 7'rp4- el/'Y 1{ f -t; ,qn eX(-s ^� f"c��l �� q/ehf-z c/� tno✓ -vur^ A y / p C%la [ � A f- , � � �(}( G1�Ge 3 Mfr'. I'�-r'e-ot �i9Qr' . Gl�o� I� (CG/'i`rc./ Or// lt�j. L( 5 li t c SV PP `' ` C• tG �✓1f� ! J ba, /G A/e cLR C( G'` �� I 4 p 1 pf Si R(J� a d 'e K , f Q l° /k e / q� r c y � [ � �i /' .� p,1 -,1"- p) r1 -,1"-p/ f -F--,.mss c1r-c/v.e��C gLK�TIAS / Sq. Ft./LF Btu's Gallons Amps 2--00 Squares Other ProJect Value: (Contract value or the cost of all materials and labor included in the entire project) OWNER/CONTRACTOR SIGNATURE OF UNDERSTANDING AND AGREEMENT T hereby certify, that the setback distances proposed by this permit application are accurate and do not violate applicable ordinances, rules or regulations of the City of Wheat Ridge or covenants, easements or restrictions of record; that all measurements shown and allegations made are accurate; that 1 have read and agree to abide by all conditions printed on this application and that I assumefull responsibility for compliance with applicable City of Wheat Ridge codes and ordinances for work under any permit issued based on this application; that I am the legal owner or have been authorized by the legal owner of the property to perform the described work and am also authorized by the legal owner of any entity included on this application to list that entity on this application. CIRCLE ONE: (OWNER)_CONTRACTOR r (A UTHORIZED REPRES NTA o OWNER) (CONTRACTOR) PRINT NAME;A /Gl/`�i` SIGNAT DATE: 1/10 r Z �" X7 ZONING COMMMENTS: Reviewer: BUILDING DEPARTMENT COMMENTS: Reviewer: PUBLIC WORKS COMMENTS: Reviewer: PROOF OF SUBMISSION FORMS Fire Department ❑ Received ❑ Not Required Water District ❑ Received ❑ Not Required Sanitation District ❑ Received n Not Required DEPARTMENT USE ONLY OCCUPANCY CLASSIFICATION: Building Division Valuation: $ City of W hCat ic�gC CITY OF WHEAT RIDGE BUILDING AND INSPECTION SERVICES DIVISION 7500 W 29th Ave Wheat Ridge, CO 80033-8001 p. 303.235.2855.f 303.237.8929 Proof of Submission for Permitting/Plan Review A copy of this form must be completed by each agency indicated on the Permit Submittal Checklist for the project type and be attached to the Building Permit Application at the time of submission. Applications presented for submission without a completed Proof of Submission form from a required agency will not be accepted or processed. Date: 10 2-6- 2yl �7 Project Address: Name of Firm/Individual submitting documents: ✓C' S �v. ; C�� Project Type/Description: Signature of Firm Representative or Individual: DO NOT WRITE BELOW THIS POINT - FOR AGENCY USE ONLY am a duly authorized representative of the agency indicated below and do, by my signature below, hereby acknowledge receipt of documents necessary for review and approval of the project indicated above. Agency represented: (Please check one) Wheat Ridge Fire Protection Arvada Fire Protection o Wheat Ridge Water District o Consolidated Mutual Water District o Valley Water District o Denver Water Agency Notes: o Wheat Ridge Sanitation District o Clear Creek Sanitation District o Fruitdale Sanitation District o Westridge Sanitation District o Other G Signature: Date: �Q r (Agency epresentative) PLAN CHECK LOG ov Address: .T / .. 7U Ed—a-me // PC# 0170 0 aQ Date Description '- WIF49 I st (Fw at Fe�-/vim 2Nro<.�rr/ L:,�:M4 e� CITY OF Wheat Ridge Co COMMUNITY DEVELOPMENT DEPARTMENT BUILDING DIVISION Project Description: Project Address: Permit App. Date: Permit Valuation: Type of Use: Occ. Group: No. Stories: Design Professional: Applicant Contact: Plan Check Engineer: Engineer's Email: TENANT IMPROVEMENT PLAN REVIEW COMMENTS Plan Check No.: Plan Check. Expires: Adjusted Valuation: Type of Const.: Fire Sprinklers: Occ. Load: Phone: Phone: Phone: X 1 sl Review: 2"d Review. 31 Review: Italic comments FIBold Comments By Appt. The project plans were reviewed for compliance with the following codes and standards: 2012 IRC; 2012 IBC; 2012 IPC; 2014 IEC; 2012 MC; 2012 IECC The code section references are from the 2012 IBC, unless otherwise stated. RESPONSE LETTER. To expedite project approval, Please provide a separate written response indicating the sheet number, note number & or detail number where each comment was addressed on the plans. • Cloud and delta all revisions and include in the title block of all pages. • Resubmit all previously reviewed plans, updated plans and supporting documents with each subsequent review. • AFTER 2nd PLAN REVIEW: Please call the plan check engineer listed above to schedule a plan review appointment, to expedite project approval. • For clarification of any plan review comment, please call the plan check engineer listed above. Note: Plan checks expire 180 days from date of submittal. GENERAL Approval is required from the following departments: a. Building Dept. review. b. Arvada Fire Authority c. Planning Department 2. Rechecks exceeding the 2nd review must schedule an appointment with the plans examiner for the third and each subsequent resubmittal. 3. Final drawings which will be approved for permit issuance shall be wet signed by the respective design professionals. 4. The proposed tenant improvement scope includes changes to the building safety system including one or more of the following building components (building fire rated components, building exit access, exits, smoke partition, fire partition, fire barrier). Provide a Colorado licensed architect stamp and signature on tenant improvement drawings. 5. Specify on the cover sheet if this is a sprinklered or non-sprinklered building. 6. Note the prior space use and adjacent uses on the plans. 7. Please change the code year on the cover sheet from 2015 IFC to 2012 IFC FLOOR PLAN & MISC. CONSTRUCTION DETAILS 8. Please label each room and their use. OCCUPANCY PROTECTION & SPECIAL USESStorage exceeding 12,000 sq. ft. 9. Provide detailed drawings for firewall assemblies and firewall penetrations. 10. Please provide details for fume extraction. 11. Please provide details for return air in the finish room 12. How will the fumes be prevented from entering the return air? Will there be a scrubber EXITING 13. Provide a door schedule and specify accessible hardware for each door. 14. Two exits are required; show the installation locations of overhead exit signs throughout the floor plans. 1011.1, 1011.3 DISABLED ACCESS DOORS 15. Handles, pulls, latches, locks, and other operable parts on doors and gates that are in a path of travel shall be operable with one hand and shall not require tight grasping, pinching or twisting of the wrist. (404.2.6). Operable parts of such hardware shall be 34" minimum and 44" maximum above the finish floor or ground (404.2.6). 16. Note on the door schedule: Maximum force to for pushing or pulling open, exterior or interior hinged doors with closers and sliding or folding doors, shall not exceed five pounds. Minimum allowable opening force, for fire doors, not to exceed 15 pounds. EMPLOYEE WORK AREAS 17. Spaces and elements within employee work areas shall be designed so that individuals with disabilities can approach, enter, and exit the work area. Common use circulation paths within employee work areas shall comply with section (402.2) 1VLIAIZ[r17911J►11f_11kIP 18. No fewer than two drinking fountains shall be provided, one shall comply with sections (602.2) through (602.6) and the other one shall comply with section (602.7). When a single drinking fountain complies with all of the above listed sections, it shall be permitted to be substituted for two separate drinking fountains. INDIVIDUAL USE SANITARY FACILITIES 19. Toilet rooms shall comply with section (603). (213.2). Turning space of 60" min shall be provided within the room (603.2.1). Turning space shall be permitted to include knee & toe clearance complying with section (306). Door shall not swing into the 30"X48" clear floor space or clearance required for any fixture. 20. Doors shall not swing into the clear floor space or clearance required for any fixture. (603.2.3). Exception 2: Where the toilet or bathing room is for individual use and clear floor space complying with Section (303.5) is provided within the room beyond the arc of the door swing, doors shall be permitted to swing into the clear floor space or clearance required for any fixture 21. All gender toilet rooms shall not contain more than one lavatory, and not more than two water closets without urinals or one water closet and one urinal. (213.2.1). 22. The uni-sex bathroom door swing does not match the detailed description, please adjust on sheet P-1 23. Please provide large detail for the Uni-Sex Bathroom. 3 City of Wheat Ridge Commercial Demolitio PERMIT - 201708267 PERMIT NO: 201708267 ISSUED: 10/12/2017 JOB ADDRESS: 11415 W I-70 Frontage RD N EXPIRES: 10/12/2018 JOB DESCRIPTION: Permit for a interior demo: Removing non -load bearing walls, outlets, ceiling grid, tiles and wires. Demo all T-12 light fixtures. Preparing suite for Tenant Improvement to be on separate permit. *** CONTACTS *** OWNER (303)423-9700 SIX OAK LIMITED PARTNERSHIP SUB (303)888-2968 Mike Mueller 090040 Five Star Contracting LLC *** PARCEL INFO *** ZONE CODE: UA / Unassigned USE: UA / Unassigned SUBDIVISION CODE: 420 / Storage Warehouse; 0 BLOCK/LOT#: 0 / *** FEE SUMMARY *** ESTIMATED PROJECT VALUATION: 3,000.00 FEES Total Valuation 0.00 Use Tax 63.00 Demolition Fee 50.00 ** TOTAL ** 113.00 *** COMMENTS *** *** CONDITIONS *** Must comply with 2012 IBC, 2014 NEC and all applicable City of Wheat Ridge Municipal Codes. Work is subject to field inspections. **Prior to final inspection approval I by my signature do hereby attest that the work to be performed shall comply with all accompanying approved plans and specifications, applicable building codes, and all applicable municipal codes, policies and procedures, and that I am the legal owner or have been authorized by the legal owner of the property and am authorized to obtain this permit and perform the work described and approved in conjunction with this ermit. I further aft I egal thorized to include all entities named within this document as parties to the work to be per or t erfo d is disclosed in this document and/or its' accompanying approved plans and specifications. A7-/ 2 -moo/ Signature OWNER or CO TRACTOR (Circle one) Date 1. This permit was issued based on the information provided in the permit application and accompanying plans and specifications and is subject to the compliance with those documents, and all applicable statutes, ordinances, regulations, po plans and procedures. 2. This permit shall expire 365 days after the date of issuance regardless of activity. Requests for extension must be made in writing, and received prior to the date of expiration. An extension of no more than 180 days made be granted at the discretion of the Chief Building Official and may be subject to a fee equal to one-half of the originalpermit fee. 3. If this permit expires, a new permit may be required to be obtained. Issuance of a new permit shall be subject to the standard requirements, fees androcedures for approval of any new permit. Re -issuance or extension of expired permits is at the sole discretion of the Chief Building Official and is not guaranteed. 4. No work of an manner shall be performed that shall results in a changeof the natural flow of water without prior and specific approval. 5. The permit holder shall notify the Building and Inspection Services Division in accordance with established policy of all required inspections and shall not proceed or conceal work without written approval of such work from the Building and Inspection Services Division. 6. The issuance or granting of a permit shall not be construed to be a permit for, or an approval of, an violation of any provision of any applicable code or any ordinance or regulation of this jurisdiction. Approval of work is subject to field inspection. • Signature of Chief Building Official Cl�ate REQUESTS MUST BE MADE BY 11:59PM ANY BUSINESS DAY FOR INSPECTION THE FOLLOWING BUSINESS DAY. (il�' ()IW heat ici c Building & Inspection Services Division 7500 W. 29" Ave., Wheat Ridge, CO 80033 Office: 303-235-2855 * Fax: 303-237-8929 Inspection Line: 303-234-5933 FOROFFICE USE ONLY Date: PlanlPennit # Plan Review Fee: Building Permit Application ' Please complete all highlighted areas on both sides of this form. incomplete applications may not be processed. *** Property Address: I.J. q 115 tAJ 1-70 Wkcc4 Ri da e_ W 20033 Owner C` C. ks Property Owner Email: Ki4��u,�r1L « CCr Cct 1 . r1C Mailing Address: (if different than property address) Address: I 1 Ll57 v\L 'c �� Rrt • �v (5 <� 4l City, State, zip: W 4te Cx-A- CC) C'>( 3 Ar—chitectLEnaineer• N1 i C 1 ad M o'l F c Architect/Engineer E-mail: r,> Fi v' c S+(-(#-- Cn t1J-rL1 L, C Contractors City License #: C' g c o l{ c) Phone:(3C'-3) -632- Contractor E-mail Address: rti1t, kc -Ci VC- S- a C (-, (F (�o l . C cI nIq Sub Contractors: Electrical: Sc;ide.d W.R. City License # ,/0 2-7 Z Other City Licensed Sub: City License # Plumbing: W.R. City License # Other City Licensed Sub: City License # Mechanical: W.R. City License # Complete all information on BOTH sides of this form Descriution of work: (Check all that apply) ❑ NEW COMMERCIAL STRUCTURE ❑ ELECTRICAL SERVICE UPGRADE ❑ NEW RESIDENTIAL STRUCTURE ❑ COMMERCIAL ROOFING ❑ COMMERCIAL ADDITION ❑ RESIDENTIAL ROOFING ❑ RESDENTIAL ADDITION ❑ WINDOW REPLACEMENT ❑ COMMERCIAL ACCESSORY STRUCTURE (Garage, shed, deck, etc.) ❑ RESIDENTIAL ACCESSORY STRUCTURE (Garage, shed, deck, etc.) ❑ MECHANICAL SYSTEM/APPLIANCE REPAIR or REPLACEMENT ❑ PLUMBING SYSTEM/APPLIANCE REPAIR or REPLACMENT ❑ ELECTRICAL SYSTEM/APPLIANCE R PAR or REPLACEMENT ,OTHER (Describe) " +rin rL , c 15 C� 11t 0 (For ALL projects, please provide a detailed description of work to be performed, Including current use of areas, proposed uses, square footage, existing condition and proposed new condition, appliance size and efficiency, type and amount of materials to be used, etc.) � 6e,/0-0 (�/� � � f ° =l. ,l tAAGe 1h S i,-, % r' at AJ Sq. Ft./LF �j (7 Btu's Amps Squares Gallons Other Project Value: (Contract value or the cost of all materials and labor included in the entire project) $_300 00 OWNER/CONTRACTOR SIGNATURE OF UNDERSTANDING AND AGREEMENT I hereby certify that the setback distances proposed by this permit application are accurate and do not violate applicable ordinances, rules or regulations of the City of Wheat Ridge or covenants, easements or restrictions of record; that all measurements shown and allegations made are accurate; that I have read and agree to abide by all conditions printed on this application and that I assume full responsibility for compliance with applicable City of Wheat Ridge codes and ordinances for work under any permit issued based on this application; that I am the legal owner or have been authorized by the legal owner of the property to perform the described work and am also authorized by the legal owner of any entity included on this application to list that entity on this application. CIRCLEONE (OW)VE CONTRACTO ar (AUTHORIZE E SE ATI V o NER 0 ) (CONTRACTOR) PRINT NAME: �� I �/ 9 / ,h> IV - ZONING ZONING COMMMENTS: Reviewer. BUILDING DEPARTMENT COMMENTS: Reviewer. PUBLIC WORKS COMMENTS: Reviewer. PROOF OF SUBMISSION FORMS Fire Department ❑ Received ❑ Not Required Water District ❑ Received ❑ Not Required Sanitation District ❑ Received ❑ Not Required DEPARTMENT USE ONLY DATE: OCCUPANCY CLASSIFICATION: Building Division Valuation: $ Fa 1 W 3650 Chestnut Place, Denver, Colorado 80216 M, rMTrki Phone. 30.296.6022 /Fax. 30.292.1451 September 14, 2015 Kirby Kunz Six Oak Limited Partnerships 11457 W. I-70 Frontage N. Road via Email: kirbykunz(ccomcast.net Denver, Colorado 80033 RE: Inspection for Asbestos -Containing Materials 11415 W. I-70 Frontage N. Road LU 10 ��m Baer, CO 80033 e' l Family Environmental Project Number: 090815-1 Dear Mr. Kunz, Family Environmental Compliance Services, Inc. (Family Environmental) is pleased to submit this report summarizing the inspection activities conducted at the commercial building located at 11415 W. 1-70 Frontage N. Road, Denver, CO 80033 (the Site). Family Environmental was contracted by Kirby Kunz (the Client) on September 8, 2015 to inspect and identify suspected Asbestos Containing Material (ACM), collect and submit samples for laboratory analysis, and provide an inspection report. Fieldwork was performed on September 9, 2015. Data gathered during the visual inspection of the Site, collection of bulk samples of inspected suspect building materials, and the interpretation of analytical results is intended to provide information that meets federal, state, and local regulatory requirements. The sampling and inspection process was conducted in accordance with the following standards: • Asbestos Hazard Emergency Response Act (AHERA) — 40 CFR 763 Subpart E sections 763.80 to 763.99 • Colorado Department of Public Health & Environment (CDPHE) Regulation Number 8 (Reg. 8) • United States Environmental Protection Agency (EPA) National Emissions Standards for Hazardous Air Pollutants (NESHAP) — 40 CFR 61 Part M • Occupational Safety and Health Administration (OSHA) asbestos regulations — 29 CFR 1926 parts 58 and 1101, and 29 CFR 1910 Parts 134 and 1001 1.0 REGULATORY COMPLIANCE This inspection was performed in anticipation of renovation/demolition activates that are expected to impact suspected asbestos containing building materials. Asbestos has been added to over 3,000 materials and products produced and used in the United States. Suspected ACMs include nearly all building materials with the exception of glass, metal or rubber. According to AHERA and CDPHE Reg. 8, suspect ACMs must be properly sampled and submitted for analysis before any disturbance occurs at the Site. For a building material to be categorized as ACM, it must contain asbestos in a quantity greater than one percent, as confirmed by an EPA accredited National Voluntary Laboratory Accreditation Program (NVLAP) laboratory. ACMs are categorized into two subsequent categories, non -friable asbestos and friable asbestos. Non -friable asbestos is any material that 3650 Chestnut Place, Denver, Colorado 80216 Phone. 303.296.6022 / Fax: 30').292.1451 cannot be crumbled, pulverized or reduced to a powder by hand pressure when dry. Friable asbestos can be crumbled, pulverized, or reduced to a powder by hand pressure when dry. ACMs identified in this report are subject to the EPA NESHAP Regulations for Asbestos and the CDPHE Reg. 8. The CDPHE is responsible for the administration of the EPA NESHAP program in Colorado. EPA NESHAP prohibits the release of asbestos fibers into the atmosphere during renovation or demolition activities. The asbestos NESHAP requires that potentially regulated ACMs be identified, classified, quantified and removed where necessary prior disturbance. All friable ACM as well as non -friable ACM that can be rendered friable during demolition or renovation activities must be removed by a licensed General Abatement Contractor (GAC). Materials containing asbestos quantities of one percent (1%) or less are also be subject to OSHA regulations if air concentrations sampled during demolition or renovation activities are at or above the permissible exposure limit (PEL) of 0.10 fibers per cubic centimeter (f/cc) as an eight hour time weighted average, or the excursion limit of 1.0 f/cc as averaged over a 30 minute sampling period. OSHA regulations for General Industry and the Construction Industry include provisions for communication of hazards by the building owner, to building employees, or in the case of subcontracted building services, the subcontractor to subcontractor employees: • The employer must inform maintenance staff and subcontractors if building components have the potential to expose staff and subcontractors to asbestos. • The building owner shall maintain records concerning the presence, location and quantity of ACMs in the building for the duration of ownership, and records shall be transferred to any successive owners. • The building owner shall affix labels or signs to positively identified ACMs so that employees and building visitors will be notified of materials that contain asbestos. Such labels or signs shall be placed in areas where employees are likely to impact ACMs as a part of their work. ram�3650 Chestnut Place, Denver, Colorado 80216 kWrWrkJJ __ Phone: 303.296.6022 / Fax: 303.292.1451 2.0 SITE / BUILDING INFORMATION The subject building is located at 11415 W. I-70 Frontage N. Road, Denver, CO 80033. This was a pre -renovation investigation. Drawings of the existing conditions and renovation designs were not provided to Family Environmental prior to the inspection and sampling activities. The building is approximately 12,297 square feet (ft) and is primarily composed of wood, metal, wall board, and drywall construction. The commercial building featured two (2) bathroom, kitchen, offices and a storage room. During the inspection, the inspector was able to identify and inspect: • Fifteen (15) functional spaces were identified. • Thirteen (13) functional spaces were surveyed. • Two (2) functional spaces were inaccessible or excluded from this inspection. o Wall/ceiling cavities in the building o Exterior on the building 3.0 FIELD ACTIVITIES On September 9, 2015, an AHERA/CDPHE accredited asbestos inspector from Family Environmental conducted a limited asbestos inspection of the Site. The purpose of this asbestos inspection was to evaluate for the presence of ACM in the building on this property. The inspection was conducted in accordance with the methods and procedures outlined in the aforementioned documents. 3.1 Visual Assessment Inspection activities began with visual observation of interior and exterior of the shop to identify homogeneous areas for suspect ACM. Homogenous areas (materials) are classified into one of the following three categories: • Surfacing Material (S) refers to a wide range of trowel or spray -applied materials typically used for acoustical, decorative or fire proofing purposes. • Thermal System Insulation (TSI) refers to insulation that is applied to heating or mechanical system components. Examples include pipe, tank and boiler insulation. • Miscellaneous Materials (M) refers to refers to all other materials that do not fall into one of the previously mentioned categories. Examples include floor tiles, adhesives, composite drywall systems and ceiling tiles. Appendix A provides a summary of the areas determined to be homogeneous and the laboratory results for those areas. 3.2 Physical Assessment and Sample Collection A tactile assessment of each homogeneous area of suspect ACM was conducted to assess the general condition and the friability of the material. Friability was assessed by physically touching suspect materials. Following categorization for material type and friability, a sampling strategy was developed based on the following requirements: ramlKwropuptalPhone: 3650 Chestnut Place, Denver, Colorado 80216 303.296.6022 /Fax: 303.292.1451 Bulk Sampling Strategy Material Homogenous Area Units Minimum Samples Less than 1,000 3 Surfacing (S) 1,000 to 5,000 SF 5 More than 5,000 7 Thermal S stem Insulation TSI) --- LF/SF/EA 3 Miscellaneous Materials ( --- LF/SF/EA Inspectors discretion SF = SQUARE FEET LF = LINEAR FEET EA = EACH Based on the results of the visual observation, bulk samples of suspect ACM were collected in accordance with AHERA protocols. Random bulk samples of suspect materials were collected in each homogeneous area using wet methods as applicable to reduce the potential for fiber release. During the inspection, Family Environmental staff identified thirteen (13) suspect homogenous materials, and collected Thirty-eight (38) bulk samples. The following major categories of homogenous areas were identified as being suspect asbestos containing materials: • Baseboard Adhesive (BBA): Two (2) unique BBA's were identified during this inspection and two (2) were sampled. Laboratory analysis determined that the two (2) BBA's identified during this inspection were non -detect for asbestos. • Carpet Adhesive (CA): Two (2) unique CA were identified during this inspection, and two (2) were sampled. Laboratory analysis determined that the two (2) CA identified during this inspection were non -detect for asbestos. • Composite all (CDW): One (1) unique CDW was identified during this inspection, and one (1) was sampled. Laboratory analysis determined that the one (1) CDW identified during this inspection was non -detect for asbestos. • Floor Tile Composite FTC): Two (2) unique FTC's were identified during this inspection and two (2) were sampled. Laboratory analysis determined that the two (2) FTC's identified during this inspection were non -detect for asbestos. • Lav -In Ceiling Panel (LIP): Two (2) unique LIP'S were identified during this inspection and two (2) were sampled. Laboratory analysis determined that the two (2) LIP's identified during this inspection were non -detect for asbestos. • Textured Surfaces (TS): Three (3) unique TS's were identified during this inspection and three (3) were sampled. Laboratory analysis determined that the three (3) TS's identified during this inspection were non -detect for asbestos. • Wall Pa e�: One (1) unique WP was identified during this inspection, and one (1) was sampled. Laboratory analysis determined that the one (1) WP identified during this inspection was non -detect for asbestos Each sample was placed in a sealed container and labeled with a unique sample number using an indelible marker. Appendix C contains the Laboratory Analytical Summary of all of the bulk samples collected. 3.3 Chain of Custody Samples were delivered along with a completed chain -of -custody (COC) to River North Environmental Testing (RNET) Laboratory. Laboratory personnel signed and dated the COC at the time of delivery to acknowledge receipt of the samples. Upon receipt, the laboratory arranged ramKWrowntal 3650 Chestnut Place, Denver, Colorado 80216 Phone. 303.296.6022 /Fax: 303.292.1451 the samples in numerical order to establish any discrepancies between the samples set which was delivered and the COC form. Where (ii) discrepancies exist, laboratory personnel noted and initialed the COC and reported the error to the inspector. The laboratory included the signed original copy of the COC with the final analytical report for evidentiary purposes. 4.0 LABORATORY ANALYSIS All bulk samples were relinquished to RNET. All samples were analyzed via Polarized Light Microscope (PLM) in accordance with EPA/600/R-93/116 Method for the Determination of Asbestos in Bulk Building Materials. RNET is accredited by the National Voluntary Laboratory Accreditation Program (NVLAP) under Laboratory Code 200448-0. A copy of the RNET Report of Test Results can be found in Appendix C of this report. 5.0 ASBESTOS CONTAINING MATERIALS The United States EPA and OSHA define an asbestos containing material as a material containing greater than 1% asbestos, or a material that is assumed to contain asbestos. Materials that contain asbestos at or below one percent (<%) are considered to be trace asbestos containing. Current EPA and State of Colorado regulations require the removal of both confirmed, and assumed, FRIABLE ASBESTOS prior to renovation or demolition activities that will impact these materials. The following is a list of friable ACM observed by the inspector: • No friable asbestos was observed during this inspection. Depending on the renovation or demolition techniques used, the current EPA and State of Colorado regulations may require the removal of both confirmed, and assumed, NON -FRIABLE ASBESTOS prior to any activities that may impact these materials. The following is a list of non -friable ACM observed at the site: • No non -friable asbestos was observed during this inspection. Prior to any disturbance, the following ASSUMED ASBESTOS (ACM) should be sampled by a certified asbestos building inspector to determine the actual asbestos content, or be treated as asbestos containing: • No asbestos was assumed to contain asbestos during this inspection. Current EPA and State of Colorado regulations do not require the removal of materials found to contain TRACE ASBESTOS (<1%) prior to initiating renovation or demolition activities that will impact this material. The following materials contain trace amounts of asbestos: 0 No trace (<1%) asbestos was observed during this inspection. 3650 Chestnut PIace, Denver, Colorado 80216 t�l J Phone: 30.296.6022 /Fax.. 30' ).292.1451 6.0 CONCLUSIONS & RECOMMENDATIONS Based on our observations and the analytical results, no friable asbestos is present in the area of the inspection. All friable and non -friable asbestos materials must be removed by a certified abatement contractor prior to renovation or demolition. If trace (<1%) asbestos materials exist on the site, and they are not removed, the renovation or demolition contractor must be notified of the presence of this material prior to disturbance and comply with all current OSHA regulations for employee exposure to asbestos. Additionally, the renovation or demolition contractor must comply with applicable NESHAP asbestos emission control regulations for structures containing trace amounts of asbestos. These materials may not be subject to sanding, grinding or cutting during renovation or demolition activities. If during demolition/renovation activities, materials are encountered which have not been discussed in this report; stop all activities in the immediate area, and contact a certified asbestos building inspector to sample the suspect material. Family Environmental is available to perform further sampling at your request. 6.0 LIMITATIONS This asbestos inspection was conducted in a manner consistent with the level of care and skill ordinarily exercised by members of the profession currently practicing under similar conditions in the same locale. The results, findings, conclusions and/or recommendations expressed in this report are based on conditions observed during our limited inspection, and the analytical results of the samples collected. The information contained in this report is relevant to the date on which this survey was performed, and should not be relied upon to represent conditions at a later date. This limited asbestos inspection report is not considered a comprehensive inspection report and it must be understood that the existence of unique or concealed asbestos may be possible. This report has been prepared on behalf of, and exclusively for use by the client for specific application to the project indicated. Contractors or consultants reviewing this report must draw their own conclusions regarding further investigation or remediation deemed necessary. Family Environmental does not warrant the work of regulatory agencies or other third parties supplying information which may have been used in the preparation of this report. No warranty, express or implied is made. This report is not to be used as a bidding document. 3650 Chestnut Place, Denver, Colorado 80216 Phone. 303.296.6022 /Fax: 303.292.1451 Should you have any questions or require additional information or services, please feel free to contact Family Environmental at (303) 296-6022. Sincerely, Family Environmental Compliance Services, Inc. Digitally signed by Jerome Hairston Jerome DINT: Jerome Hairston, o, w, email=jhahtw@%,nilyenvironment Hairston alcom, cdJS Date 2015.09.14 12.21 IS -W00' Jerome B. Hairston CIEC Environmental Project Manager AHERA/State of Colorado Accredited Asbestos Building Inspector #3799 Air Monitoring Specialist #3799 Attachments: Appendix A: Homogenous Materials Table Appendix B: Laboratory Analytical Report Appendix C: Inspector Certifications Tristan R.M. Fitzpatrick Industrial Hygiene Program Manager AHERA/State of Colorado Accredited Asbestos Building Inspector #20249 3650 Chestnut Place, Denver, Colorado 80216 ram wropuptal Phone: 303.296.6022 /Fax: 303.292.1451 APPENDIX A HOMOGENOUS MATERIALS TABLE rdMiflkWrnnn-rrtAl3650 Chestnut Place, Denver, Colorado 80216 Phone: 303 .296.6022 / Fax: 303.292.1451 Homogenous Areas (Materials) Material Code Material Description Material Material Estimated percent & Type of Material Type Friability Quantity Locations Asbestos BBA -01 Baseboard M NFII M ND CA -01 —EDW Carpet Adhesive M NFII __ ID -01 Composite Drywall M NFII __ ND ___ FTC -01 Floor Tile Composite M NF11 -__ ND 1TC-02 Floor Tile Composite M NFII — ND LIP -01 Lay -In Ceiling Tile M NFII — ND LIP -02 Lay -in Ceiling Tile M NFII --- ND --- TS-01 Texture Surface S F __ ND _ TS -02 Texture Surface S F -- ND TS -02 Texture Surface S F ND _ WP -02 Wali Paper&Adhesive M NFII SF = SQUARE FEET LF = LINEAR FEET EA = EACH ND = NON DETECT FOR ASBESTOS f�m{• 3650 Chestnut Place, Denver, Colorado 80216 ' Phone.. �0�.296.6022 (l~ax.. )0).292.145i APPENDIX B LABORATORY SUMMARY OF BULK SAMPLES AND ANALYTICAL RESULTS River North Environmental Testing, Inc. 9/10/2015 Family Environmental Services 3650 Chestnut Place Denver, Colorado 80216 Re: 11415 W. I-70 Frontage N. Road ;090815-1 PLM15-507 Mr. Hairston, Attached are the results of Polarized Light Microscopic (PLM) analysis for asbestos contained in the bulk sample materials submitted to this facility on 9/10/2015 Bulk samples are analyzed in accordance with USEPA test method EPR/600/M4-82-020 and EPA/600/R- 93/116, which requires that distinctly different materials or layers present within a sample be analyzed and reported separately. (For measurement uncertainty, refer to table 2.1 in EPA/600/R-93/116 method.) Sometimes it is not possible to completely separate thin or strongly adhering layers, such as paint or adhesive, and a combined result is given. For some complex materials, such as drywall/tape/mud joints, a composite or overall asbestos content may be reported in addition to individual layer results. RNET, Inc. is currently accredited for bulk asbestos analysis by the National Voluntary Laboratory Accreditation Program (NVLAP) of the National Institute of Standards and Technology (NIST). Our NVLAP laboratory code number is 200448-0. Due to the limitations of the EPA 600 Method, nonfriable organically bound materials (NOBs) such as floor tiles can be difficult to analyze via PLM. EPA recommends that all NOBS reported as non -detect by PLM analysis be further analyzed by Transmission Electron Microscopy for more definitive results. Please note that the PLM analysis of dust and soil samples for asbestos is not covered under NVLAP accreditation. The analytical results provided in this report apply only to the samples submitted to the laboratory. This report is confidentiai. Details of this report will not be discussed with any person or agency not associated with you or your organization. This report must be reproduced in its entirety and shall not be copied in part or used by the client to claim product endorsement by NVLAP or any agency of the U.S. Government, Samples will be held for a minimum of sixty days unless longer storage is requested. If you have any questions regarding the content of this report please call RNET, Inc. at 303-297-0079. Brendon Rawlings Asbestos Analyst—/ brawlings@famiilyenviror,mental.com Cell: 724-263-€3800 Katie Shaw PLM Laboratory Manager/Asbestos Analyst kshaw@familyenvironmentai.com Cell: 307-631-4020 River North Environmental Testing, Inc. REPORT OR TEST RESULTS PLM Bulk Asbestos Analysis NVLAP Lab Code 200448-0 CLIENT: Family Environmental Compliance Services PROJECT: PLM15-507 Lab -ID No. Layer No, Asbestos Non -Asbestos Sample ID Description Layer % Type {%} Components ° PLM 15-507-01 11415 -6 -BBA -01-1 Paper/Mastic, Brown/Off White, Non- LAYER 1 None Detected Cellulose Fiber 40% homogeneous, Resinous/Fibrous 100% Resin 60% PLM 15-507-02 11415 -5 -BBA -01-2 Mastic, Tan, Homogeneous, LAYER 1 None Detected Talc 100 ,o Resin Resinous 98 o /o 98 PLM 15-507-03 11415 -1 -BBA -02-1 Mastic, Brown, Homogeneous, LAYER 1 None Detected Talc Resinous 1001 °. 2% Resin; gg % PLM 15-507-04 11415 -2 -BBA -02-2 Mastic, Brown/Tan. Non- LAYER 1 None Detected Talc 2% homogeneous, Resinous 100% Resin 9&% PLM 15-507-05 11415 -13 -CA -01-1 Mastic, Tan, Homogeneous, LAYER 1 None Detected Talc 2% Resinous 100% Resin 98% PLM 15-507-06 11415 -12 -CA -01-2 Mastic. Tan, Homogeneous, LAYER 1 None Detected Talc 2% Resinous 100% Resin 98% PLM 15-507-07 11415 -11 -CA -02-1 Mastic, Tan, Homogeneous, LAYER 1 None Detected Talc 2% Resinous 100% Resin 98% PLM 15-507-08 11415-1-CDW-01- LAYER 1 LAYER 1 None Detected 1 Cellulose Fiber ;0% Drywall with Paper, White/Brown, 8040 Other Non -Fibrous 70% Non-homogeneous, Fine Material Grained/Fibrous LAYER 2 LAYER 2 None Detected Mud, White, Homogeneous, Fine 20% Grained Other Non -Fibrous 100% Material PLM 15-507-09 11415-5-CDW-01- LAYER 1 LAYER 1 None Detected 2 Drywall with Paper, White/Brown, 80% Cellulose Fiber ;0g Non-homogeneous, Fine Other Non -Fibrous 70% Grained/Fibrous Material LAYER 2 LAYER 2 None Detected Mud, White, Homogeneous, Fine 20% Grained Other Non -Fibrous 100% Materia! Page 1 of 5 River Noah Environmental Testing, Inc. .._ !i.— it 7• - T REPORT OF TEST RESULTS PLM Bulk Asbestos Analysis NVLAP Lab Code 200448-0 CLIENT: f=amily Environmental Compliance Services PROJECT: PLM 15-507 Lab -ID No. Layer No. Asbestos Non -Asbestos Sample ID Description Layer % Type {°/Qj Components PLM15-507-10 11415-6-CDW-01- Drywall with Paper, VVhite(Brown, LAYER 1 None Detected Cellulose Fiber 3 Non-homogeneous, Fine 100°% Other Non -Fibrous Grained/Fibrous Material PLM 15-507-11 11415-9-CDW-01- Drywall with Paper, White/Brown. LAYER 1 None Detected Cellulose Fiber 4 Non-homogeneous, Fine 100°% Other Non -Fibrous Grained/Fibrous Material. PLM 15-507-12 11415-1 1-CD`,At- LAYER 1 LAYER 1 None Detected Cellulose Fiber 01-5 Drywall with Paper, White/Brown, 70 Non-homogeneous, Fine Other Non -Fibrous Material Grained/Fibrous LAYER 2 LAYER 2 done Detected Cellulose Fiber Mud/Tape. White/Cream, Non- 20% Other Non -Fibrous homogeneous, Fine Grained/Fibrous Material LAYER 3 LAYER 3 None Detected Mud: White, Homogeneous, Fine 10% Other Non -Fibrous Grained Material PLM 15-507-13 11415 -6 -FTC -01-1 LAYER 1 LAYER 1 None Detected Floor Tile, Tan. Homogeneous, 90% Resinous Resin LAYER. 2 LAYER 2 None Detected Mastic, Black: Homogeneous, 10°% Resinous Resin PLM 15-507-14 11415 -7 -FTC -01-2 LAYER 1 LAYER 1 None Detected Floor Tile, Tan, Homogeneous, 90% Resinous Resin LAYER 2 LAYER 2 None Detected Mastic, Black. Homogeneous, 10°% Resinous Resin PLM 15-507-15 11415 -10 -FTC -01- 3 LAYER 1 LAYER 1 None Detected Floor Tile, Tan. Homogeneous, 90%Resinous Resin LAYER 2 LAYER 2 None Detected Mastic, Black, Homogeneous, 10% Resinous Resin N 30% 70% 30% 70% 30% 70°% 50% 50% ?00° 100°% 100E% 100% 100% 100% 1000/e Page 2 of 5 River Noilh Environmental Tasting, Inc. REPORT OF TEST RESULTS PLM Bulk Asbestos Analysis NVLAP Lab Code 200448-0 CLIENT: Family Environmental Compliance Services PROJECT: PLM15-507 Lab -ID No.Layer No. Asbestos Sample 1D Description Layer % Type Coo {°iaj Commponponestos ents PLM 15-507-16 11415 -4 -FTC -02-1 LAYER 1 LAYER 1 None Detected Floor Tile, Tan, Homogeneous. 90% Resinous Resin 100% LAYER 2 LAYER 2 None Detected Mastic, Yellow, Homogeneous, 10% Resinous Resin 100% PLM 15-507-17 11415 -9 -FTC -02-2 LAYER 1 LAYER 1 None Detected Floor Tile, Tan, Homogeneous, 90% Resinous Resin. 100% LAYER 2 LAYER 2 None Detected Mastic, Yellow. Homogeneous, 10% Resinous Resin 100% PLM 15-507-18 11415 -8 -FTC -02-3 LAYER 1 LAYER 1 None Detected Floor Tile, Tan, Homogeneous, 90% Resinous Resin 100% LAYER 2 LAYER 2 None Detected Mastic, Yellow, Homogeneous, 10% Resinous Resin 100 PLN, 15-507-19 11415 -9 -LIP -01-1 Ceiling Tile/Paint, Oft White/White, LAYER 1 None Detected Non-homogeneous. Fibrous ° Cellulose Fiber 30 100% Fibrous Glass 10°!°% Other Non -Fibrous 60% Material PLM15-507-20 - 11415 -9 -LIP -01-2 Ceiling Tile/Paint, Off White/White, LAYER 1 None Detected Non-homogeneous, Fibrous 100% Cellulose Fiber 10% Fibrous Glass 10°% Other Non -Fibrous 60% Material PLM 15-507-21 11415 -9 -LIP -01-3 Ceiling Tile/Paint, Off White/White, LAYER ? None Detected Cellulose Fiber 300° Non-homogeneous, Fibrous 100% Fibrous Glass 10% Other Non -Fibrous 60% Material P LM 15-507-22 11415 -9 -LIP -02-1 Ceiling Tile!Paint, Off WhitePddhite, LAYER 1 Non-homogeneous, Fibrous °. None Detected Cellulose Fiber 30% 100 i° Fibrous Glass 10,0 Oiher Non-Fib,Qus 50'A Materia! Page 3 of 5 Rivet' Notih Environmental Testing, Inc. REPORT OF TEST RESULTS PLM Bulk Asbestos Analysis NVLAP Lab Code 200448-0 CLIENT: Family Environmental Compliance Services PROJECT: PLM15-507 Lab-ID No. Layer No. Asbestos Non-Asbestos Sample ID Description Layer % Type {°I°} Components PLM15-507-23 11415-6-LIP-02-2 Ceiling Tile/Paint, Off White/White, LAYER 1 None Detected Cellulose Fiber 30% Non-homogeneous. Fibrous 100% Fibrous Glass 10% Other Non-Fibrous 60% Material PLM 15-507-24 11415-2-LIP-02-3 Ceiling Tile/Paint, Off WhitelWhite, LAYER 1 None Detected Cellulose Fiber 30% Non-homogeneous, Fibrous 100% Fibrous Glass 10% Other Non-Fibrous 60% Material PLM 15-507-25 11415-4-TS-01-1 Paper(Mud, BrownNWite, Non- LAYER 1 None Detected Cellulose Fiber 40% homogeneous. Fine Grained/Fibrous 100% Other Non-Fibrous 60% PLM 15-507-26 11415-6-TS-01-2 Paper/Paint, Brown/Olt White, Non- LAYER 1 None Detected Cellulose Fiber 30% homogeneous, Fibrous 100% Other Non-Fibrous 20% PLM 15-507-27 11415-7-TS-01-3 Paper/Paint: Brown/Off White, Non- LAYER 1 None Detected Cellulose Fiber 80% homogeneous, Fibrous 100?% Other Non-Fibrous 20°r0 PLM15-507-28 11415-10-TS-02-1 Paper/Paint, Brown/Off White, Non- LAYER 1 None Detected Cellulose Fiber 80% homogeneous, Fibrous 100% Other Non-Fibrous 20% PLM 15-507-29 11415-9-TS-02-2 Paper/MudlPaint, Bro~.wnJO€f LAYER 1 alone Detected Celiuicse Fiber 40% Whitefflhite, Non-homogeneous. 100/0 Other Non-Fibrous 60% Fine Grained/Fibrous Material PLM15-507-30 11415-9-TS-02-3 Paper/Paint, Brown/White, Non- LAYER 1 None Detected Cellulose Fiber 80% homogeneous, Fibrous 100% Other Non-Fibrous 20% LINA 15-507-31 11415-9-TS-03-1 PaperiPaint, brownfthite and Blue: LAYER ? None Detected Ceiluiose Fiber 80% Non-homogeneous, Fibrous 100% Other Non-Fibrous 20",x° PL M15-507-32 11415-12-TS-03-2 Paper/Paint, Brown/White and Blue, LAYER 1 None Detected Cellulose Fiber 80% Non-homogeneous. Fibrous 100% Other Non-Fibrous 20% Page 4 of 5 . . � Rivet, 00ofth Environmental Testing, Inc. REPORT OF TEST RESULTS PLM Bulk Asbestos Analysis mvLAPLab Code 20044O'0 CLIENT: Family Environmental Compliance Services PROJECT: PLyN15'507 Lab -ID No. Layer No. Asbestos Non -Asbestos Sample |O Description Lmyer% Type Components PLM15'507'33 11415'13'TS'03'3 Papor/Pa|nt.Brown/White and Blue, LAYER None Detected Cellulose Fiber Non'homogenooun, Fibrous 100% Omo,wpn'Fm,nuv PLM15'507'34 11415'1-kYYP'O1'1 YVa8puper, Brown/OffWhiha' Non- LAYER MomeDemcied Cellulose Fiber homogeneous, Fibrous 100v6 Other Non -Fibrous PLM15'507-35 11415'2'YVP401<2 VVa8paper,Bnuwn/Bkm. Non' LAYER None Detected Cellulose Fiber knmnganaoum. Fibrous 100% Other Non -Fibrous PLM15-507-36 11415'3-WP'01'3 VVaUpoper.Bnown/N/hits. Non- LAYER None Detected Cellulose Fiber homogeneous, Fibrous 100% Other Nor-Fibroue — _ PLM 15-507-37 - 11415 -5 -WP -01'4 Wallpaper, Brown/Blue, Non LAYER None Detected Cellulose Fiber homogeneous, Fibrous /00n, {noe,Non'r/bmup ' - pLM15-507-38 11415'0 -WP -01'5 Wu||paper.Bnown&Vhbe. Nun LAYER None Detected Cellulose Fiber homogeneous, Fibrous 100% Other ' ADD|TlONALCOM/NENT8: All separable parts nrlayers (except paint) within the same sample are analyzed and reported individually. Composite asbestos percent is reported, if applicable, by visual estimation. ND= None Detected TR=Trace, less than 1.096 ) Brendon Rawlings Date: 09/10/20115 M 50% Page 5 o, 5 Document No: FCF-04.00 Effective Date: 10/17/2013 Client: Family Environmental Compliance Services Address: 3650 Chestnut Place Denver, CO 80213 Phone #: 303-296-6022 Page 1 of 2 River North Environmental Testing, Inc 3650 Chestnut Place • Denver, CO 80216 Ph: 303-297-0079 9 Fax: 303-292-1451 www.rnetesting.com • info@rnetesting.com Contact: Jerome Hairston Fax #/Emaii: Jhairstonfamilvenvironmentai com Date Sampled: 9/9/2015 Sample location: 11415 W. 1-70 Frontage N. Road #090815-1 Special Instructions: r Total Number of Samples: 20 Sample Condition (Accept/Reject): Requested Turnaround Time: ()RUSH ** { }Next Da y (x ) 3-5 Days RUSH Turn@ d times required prior notification. Additional fees may apply. Call tab for more detaiis. Relinquished by� A " Received by: Date/Time:_j Date/Time: Relinquished by: Received by; Date/Time: Date/Time: Document No: FCF-04.00 Effective Date: 10/17/2013 Client: Family Environmental Compliance Services Address: 3650 Chestnut Place Denver, CO 80213 Phone #: 303-296-6022 LCI Page 2 of 2 River North Environmental Testing, Inc 3650 Chestnut Place • Denver, CO 80216 Ph: 303-297-0079 • Fax: 303-292-1451 www.rnetesting.com * info@rnetesting.com Contact: Jerome Hairston Fax #/Email: JhairstonCa�familvenvironmenta! com Date Sampled: 9/9/2015 Sample Location: 11415 W, 1-70 Frontage N. Road #090815-1 Special Instructions: Total Number of Samples: 18 Sample Condition (Accept/Reject) l y neyuestea l urnaround Time: {) RUSH "** { }Next Day { x) 3-5 Days " RUSH Turnaround times required prior notification. Additional fees may apply. Call lab for more details. G J Relinquished by: Date/Time: J ; Received by: Relinquished by: ' Date/Time: R '� d D ate/Ti me: eceive by. Date/Time: DEMO LIGHTS II AND GRID 1 E41 1-6 q \ q � P 11417 it ® II it DEMO LIGHTS I-9 DEMO LIGHTS ® II DEMO GRID gllll DAO GRID gull � DEMO LIGHTS AND GRID �►, r----_---_--__----- ,__A— _ _ _ -- (r — DEMO LIGHTS AND D _m II _ qp Tu rr � II DEMtl LIGHTING II ANDS i GRID it II I 11 Ai f iilll '----�. —3 fid_ DEMO CONCRETE FLOOR TO INSTALL UNDER GROUND PLUMBING ENLARGE EXISTING RESTROOM DEMO LIGHTING AND GRID 11415 777 DEMO LIGHTS AND GRID S NO CHANGES DEMO PLAN: DEMO WALLS IN RED DEMO OUTLETS ON RED WALLS DEMO CEILING GRID, TILES AND WIRES DEMO ALL T-12 LIGHT FIXTURES DEMO DOORS IN RED WALLS 11413 Wheat COMMUNITY IDewtoPM� APPROVED Reviewred fOlr Code Cmm��i Plans EE amine,- [ pate / v'tdam' 7Mr issuaxe a 10 Perms m opprovol a/plom 'dco^putaans shop not he 0—for, or an r :P�4kotians of Me provisions o/the boNdiny code oro PP oral% any vaatan to umhgtoptreovfhoriry to violofe fa Y City o,dhonces. Amok, ar 0ow I- nes o/catcel fhe p oyhions of the swidyp of the Ciry shy! not 6e votyt NORTH 0 z 0 a 0 a � = w X < fOZ o Q� CL_ co Hyo I o o��L"'i" (3) La O n W x W M Q_ ul M z a a Lu 0 �w 0< w z tMj of Z O p w w x o m UO ^O O V Z O w P Q N 4 N �W�>`'�r 3 ( Q v Z w Zd w M FILE NAME: DEMO PLAN DRAWN BY: MIKE MUELLER DATE: 10/2/2017 I REVISION I DATE I SCALE: 1/8' = 1' DEMO PLAN SHEET NUMBER D-1 2 0 U U J J C:) U o Z J 00 Q Z O Z O U F Q U o au Q co 'o Q Q > 0 0 I— N rn O Z a 0 UO M 00N U < OMM Y Q x of W M w Z J �w a a� w 0 z 0 a 0 a � = w X < fOZ o Q� CL_ co Hyo I o o��L"'i" (3) La O n W x W M Q_ ul M z a a Lu 0 �w 0< w z tMj of Z O p w w x o m UO ^O O V Z O w P Q N 4 N �W�>`'�r 3 ( Q v Z w Zd w M FILE NAME: DEMO PLAN DRAWN BY: MIKE MUELLER DATE: 10/2/2017 I REVISION I DATE I SCALE: 1/8' = 1' DEMO PLAN SHEET NUMBER D-1 DEPARTM£NT Of PLANNING AND DEVELOPMENT Building Permit Number : 2887 BUILDINCi iNSPECTION DNISION - 236-2855 GITY OF WHEAT RIDGE Date : 4/8/86 7500 WEST 29TH AVENUE WHEAT RIDGE, CO 80215 Property Owner : Property Address : 11415 I-70 FRONTAGE RD NO Phone : 292-2222 Contractor License No. : 18141 Company : Denver Burglar Alarm Co. Phone : 292 2222 OWNERlCONTRACTOR SIGNATURE OF UNDERSTANDING AND AGREEMENT 1 hereby certiry Mat tlre asiback d'ptances proposed by this permRappNcadon aro ecwrata, end do r~ violate apcifcabb a~diirwnces, rules or regulatbns Mthe C'dy of Wheat Ridga or covenaMs, easemenb or reahkilons W record; that aN measuromeMS ahown, and aHegatlona made are accurete; that I have read arMp sibi ree to abide by ell condkbns ted on thb plI~ fw wm Ihnce wRh the t Ridga Building epplicatlon, and that 1 essume full reson Code (U.B.C J and aq oUrer appllcable Wheat Ridge ordPnancea, for wwk urMer thie pertnR. (OWNER)(CONTRACTOR) SIGNED DATE Description : INSTALL SECURITY ALARM SYSTEM Construcdon Value : $650.00 Pertnit Fee : $45.00 Plan Review Fee : $0.00 Use Tax : $0.00 Total: $45.00 BUILDING DEPARTMENT USE ONLY Approval: Zoning : Approval: Approvai : Occupancy : Walis : Roof : Stories : Residentiai Units : Electrical License No : Plumbing License No : Mechanicai license No : Company : Company : Company : Expiration Date : Expiration Date : Expiration Date : Approval : Approval : Approval : 0 -~r 0 m (1) Thle pertWtwY heUeO M eomrdenCe With 1M Pmleiwls esl bM N Yoqx aPpYcatlon and is BublsClm ths IflWB of IM Sh08 of Caluado and BD tlM ZonNq latlons andg~IqIrpCotle of Wheatq~pp~, Calaado or siry oMa~pq{qpy (2) ordlnerroes Mths CMy. pemtll aMi 9xpits R(A) M~e wak autlwr~zed Is not commencatl wNh~7n abcly (80) daya Rom lawe AaOe a(B) Me bWWlny eWhaAzed ic suapai0etl M abandaewtllw a po~lod o1130 tleye. . (9) If Uiis pemit ~rylre0. a ~aw Pemxt meY bs acquhed fu a fee of ano-haB the ertauM mmbgN roWired, N dia~p ~ m chargee Iwve 6een ot wpl bs mede M tlro arly~nal Plans r~d OpedAadOns aM anY awpanepn or abantlonment na not axceaded one (1)1re~. ea aro metle a rc euepamlan a abeMrnmeM e~cceedt orro (1) YeetNX Nee aMA bs Peb for a newpe~. (1) hb wdic W any nN~v~ar al~ be CaM tlIN wNl tli0npe iM iwWnl Ibw of water caininp a drainaye proElem. Cp~oon~6apC~ta ahd m9fy Ms BuNdInG ~nsps~tor tweMy'tour (24) houn in edvence for NI inapectlms aM aMll feaNe xrtiMen aPPm'a~ m kupecdon carA bdae (5) (8) a~I ~I~i~ipenp~il~ ~ nry~nvdwda~♦nNeb ~us ~ aq eheN nol he mnstruetl to Ce a pertMt torna an approval of. eny Woletlon dttre proviebne ooos~or THIS PERMIT VALID ONLY WHEN SIGNED BY THE CHIEF BUILDING INSPECTOR CALL: 234-5833 24 HOURS PRIOR TO INSPECTION ~ 19~ No. H55 ~°ATE 4 ~ RECEIVED FROM 1' ' m ~ ADDRESS RS S ~ a 0 FOR . ■ ■ AMT OF I ACCOUNT CASN ~ AMT.PAI❑ S , ~ CNECK BALANCE I rnoncA ~ BY ~ v DEPARTMENT OF PLANNING AND DEVELOPMENT Building Permit Number : BUILDING INSPECTION DIVISION - 235-2855 CITY OF WHEAT RIDGE Date : 7500 WEST 29TH AVENUE WHEAT RIDGE, CO 80215 Property Owner: Data National Corp. Property Address: 11415 w.I-70 Rd. North Phone: 292-2222 Contractor License No. : 18141 Company: Denver Burglar Alarm Co. Phone: 292-2222 OWNER/CONTRACTOR SIGNATURE OF UNDERSTANDING AND AGREEMENT I hereby certify that the setback distances proposed by this permit appliwtion are accurete. and do not violate ap0~icable ortlinances, rules or regulalions of the Gity of Wheat Ritlge or covenants, easements or restrictions of record: that all measurements shown, and allegations made are accurate; that I hava read and agree to abide by all conditions printetl on this application, and that I assume full responsibility tor compliance with the Wheat Ridge 8uilding Code (U.B.C.) and all other applicable Wheat Ridge ordinances, for work under this permrt. (C'ld P: ER) (COhlTfthCTO P.) Description : Install Security Alarm System only ConstructionValue: Permit Fee : 45.00 Use Tax : Total : BUILDING DEPARTMENT USE ONLY Approval: Zoning : Approval: L Approval: Occupancy . Walls : Roof : Stories : Residential Units : E!ecirical License No : Plumbing License No : Mechanical License No : Company : Company : Company : Expiration Date : Expiration Date : Expiration Date : Approval : Approval : Approval : JPISes,Requlred Pl2tns Reauired Plans RPqulretl,gZ7 (1) This permit was issuetl in accortlance wtlh the provisions sel lorth in yopur appbwtion and is suDject lo the laws of the Stale of Coloratlo and ro the Zomn9 Regulabons and 0uilding Cotle ot Wheat Ridge, Colora0o or any other apPliwble ordinances of Ihe City. (2) 7his permrt shall erpue R(A) ihe work authorizetl is not commencetl wrthin siary (60) tlays from issue Oate or (8) lhe buAding authonzetl is suspende0 or abantlcnetl tor a periotl of 120 days. (3) If thi5 permil ezDires, a new permR may De acquired for a lee of one-half the amounl normally required, provitled no changes have been or will Ee made m the original plans and epecifications and any suspension or a6antlonmenl has not exceetled one (1) yeac 11 changes are matle or it suspension or abantlonment exceeds one (1) year, lull fees shall be paitl tor a new permit. (n) No work of any manner shall be tlone lhat will change ihe naWral flow ol waler causing a drainage problem. (5) Contracror shall nobty Ihe Builtling Inspector twenry-/our (24) hours m atlvante far all inspections and shall recerve wntten approval on mspeclion cartl before proceetliing wilh successive phases of the job. 16) The issuance of a permit or the appmval o/ tlrawinqs and specifications shail not be constmetl lo be a permit for. nor an appmval of, any violation of the pmvisions ol Ihe OWIUing CAOes or any other ortlrnance. law. Nle or regulation. Chief Building Inspector For Mayor THIS PERMIT VALID ONLY WHEN SIGNED BY THE CHIEF BUILDING INSPECTOR AND MAYOR CALL: 234-5933 24 HOURS PRIOR TO INSPECTION