HomeMy WebLinkAbout8 Hillside Drivei CITY OF WHEAT RIDGE
Building Inspection Division
(303) 235-2855 Office
INSPECTION NOTIC
Inspection Type:- "
Job Address:
Permit Number: /9 i
r
1
❑ No one available for inspection -Time M/PM
Re -Inspection required: Yes 01 -
When corrections have been made, schp#uie for re -inspection online at.
httpJ/www.ci.wheatridge.co.unspecti
t,
rf
Da speo':
r
i CITY OF WHEAT RIDGE
Building Inspection Division
(303) 235-2855 Office
INSPECTION NOTIC
Inspection Type:- "
Job Address:
Permit Number: /9 i
r
1
❑ No one available for inspection -Time M/PM
Re -Inspection required: Yes 01 -
When corrections have been made, schp#uie for re -inspection online at.
httpJ/www.ci.wheatridge.co.unspecti
t,
rf
Da speo':
r
i CITY OF WHEAT RIDGE
Building Inspection Division
(303) 235-2855 Office
INSPECTION NOTQCE
Inspection Type:--.--.
Job Address. 1 t �.
Permit Number:
❑ No one available for inspection: Time
Re -Inspection require Y No
When corrections have been made, schedule for re -inspection online at:
http://www.ci.wheatridge.co.usfinsption
Date: -2 3 -fir peor:
DO NOT REM: VE THIS NOTICE
A i CITY OF WHEAT RIDGE
Building Inspection Division
(303) 235-2855 Office
IN E6j10N. N TICE�� �t �
Inspection Type:
Job Address: f ��---_
Permit Number:
i
❑ No one available for inspection: Time ;�(� AM/PM
Re -Inspection required:Xees-' No
when corrections have been made sc� dtliq for re -inspection online at:
httpYwww.ci.wheatridge.co.us4nspection
A i CITY OF WHEAT RIDGE
Building Inspection Division
(303) 235-2855 Office
INSPECTION NOTICE
Inspection Type: Fs^A `tFle1_.
Job Address: ria 1 klAt i-.
Permit Number: '�°�y 007,1 3
1) ler k. qhs 5;4 e
❑ No one available for inspection: Time PM
Re -Inspection required: (_i No
When corrections have been made, schedule for re -inspection online at:
http✓/www. ci. wheatridge. co. uslinspection
Date: 7- a J Inspector:
DO NOT REMOVE THIS NOTICE
City of Wheat Ridge
Residential Solar PERMIT - 202000313
PERMIT NO: 202000313 ISSUED: 02/26/2020
JOB ADDRESS: 8 Hillside Dr EXPIRES: 02/25/2021
JOB DESCRIPTION: Installing 4.27 kW solar rooftop PV system, no structural required.
*** CONTACTS ***
OWNER (303)263-5561 PENNER-HOWELL
SUB (385)482-0045 LEE HATLEY 180271 BRS FIELD OPS, LLC
*** PARCEL INFO ***
ZONE CODE: UA / Unassigned USE: UA / Unassigned
SUBDIVISION CODE: 2404 / APPLEWOOD KNOLLS, PARAMOUNT HE BLOCK/LOT#. 0 /
*** FEE SUMMARY *** ESTIMATED PROJECT VALUATION: 10,715.00
FEES
Total Valuation 0.00
Residential Solar 500,00
** TOTAL ** 500.00
*** COMMENTS ***
*** CONDITIONS ***
Approved per plans and red -line notes on plans. Must comply with 2012 IRC, 2017 NEC and all
applicable City of Wheat Ridge Municipal Codes. Work is subject to field inspections.
I, by my signature, do hereby attest that the work to be performed shall comply with all accompanying approved plans and specifications,
applicable building codes, and all applicable municipal codes, policies and procedures, and that I am the legal owner or have been authorized
by the legal owner of the property and am authorized to obtain this permit and perform the work described and approved in conjunction with
this ermit. further attest that I am legally authorized to include all entities named within this document as parties to the work to be
performed nd that all work to be performed is disclosed in this document and/or its' accompanyin approved plans and specifications,
Ssigga ure of OWNER or CONTRACTOR (Circle one) Date
1. This permit was issued based on the information provided in the permit application and accompanying plans and specifications and is
subject to the compliance with those documents, and all applicable statutes, ordinances, regulations, po ides and procedures.
2. This permit shall expire 365 days after the date of issuance regardless of activity. Requests for extension must be made in writing anduil
received prior to the date of expiration. An extension of no more than 180 days made be granted at the discretion of the Chief Bding
Official and may be subject to a fee equal to one-half of the originalermit fee.
3 If this permit expires, a new permit may be required to be obtained. Issuance of a new permit shall be subject to the standard
requirements, fees and procedures for approval of any new permit. Re -issuance or extension of expired permits is at the sole discretion of
the Chief Budding Official and is not guaranteed.
4. No work of any manner shall be performed that shall results in a change of the natural flow of water without prior and specific approval.
5. The permit holder shall notify the Building and Inspection Services Division in accordance with established policy of all required
inspections and shall not proceed or conceal work without written approval of such work from the Building and Inspection Services
Division.
6. The issuance or granting of a permit shall not be construed to be a permit for, or an approval of, an violation of any provision of any
applicable code or at rdmance or regulation of this jurisdiction. Approval of work is subject to field inspection.
Signature of Chief Building Official Date
REQUESTS ?MUST BE MADE BY 11:59PM ANY BUSINESS DAY FOR INSPECTION THE FOLLOWING BUSINESS DAY.
City of
heatA,e
�COMMM1)'Ni'-T-Y DFVFLOPMENT
Building & Inspection Services
7500 W. 29th Ave., Wheat Ridge, CO 80033
Office: 303-235-2855 * Fax: 303-237-8929
Inspection Line: 303-234-5933
Email: PermitsO)ci.wheatridge.co.us
I FOR OFFICE USE ONLY I
Date:
Plan/Permit #
Plan Review Fee:
Building Permit Application
*** Complete all applicable highlighted areas on both sides of this form.
Incomplete applications may not be processed. ***
Property Address:
Propertv Owner
8 Hillside Drive, Wheat Ridge, Colorado, 80215, United States
Brenda Penner -Howell
Property Owner Email: kaepenner@gmail.com
Tenant Name (Commercial Projects Only)
Property Owner Mailing Address: (if different than property address)
Address: Same as property address
City, State, Zip:
Architect/Engineer:
Architect/Engineer E-mail:
Contractor Name: BRS Field Ops LLC
City of Wheat Ridge License #:
180271
Phone:
Phone:
Contractor E-mail Address: permitting.department@blueravensolar.com
For Plan Review Questions & Comments (please print):
Phone:
385-482-0045
CONTACT NAME (please print): Linsey McClain Phone:
CONTACT EMAIL(p/ease print): Permitting.department@blueravensolar.com
385-482-0045
26 '3 --5561
Sub Contractors (Must provide Wheat Ridge License No & Signed Subcontractor Authorization form):
Electrical: Plumbing: Mechanical:
W.R. City License # W.R. City License # W.R. City License #
Other City Licensed Sub: Other City Licensed Sub:
City License # City License #
Complete all highlighted fields.
❑COMMERCIAL D RESIDENTIAL
Provide description of work: For ALL projects, provide a detailed description of work to be
performed, including current use of areas, proposed uses, square footage, existing condition and
proposed new condition, appliance size and efficiency, type and amount of materials to be used, etc.
Residential Solar Rooftop PV System 4.27 kW
Sq. Ft./LF
Amps 200
241.5 BTUs n/a
Gallons n/a
Squares For Solar: 4.27 KW 14 # of Panels n/a Requires Structural
For Commercial Projects Only: Occupancy Type: Construction Type:
Occupancy Load: Square Footage:
Project Value: (Contract value or the cost of all materials and labor included in the entire project)
$ 10715
OWNER/CONTRACTOR SIGNATURE OF UNDERSTANDING AND AGREEMENT
I hereby certify that the setback distances proposed by this permit application are accurate and do not violate applicable ordinances, rules or
regulations of the City of Wheat Ridge or covenants, easements or restrictions of record; that all measurements shown and allegations made are
accurate; that I have read and agree to abide by all conditions printed on this application and that I assume full responsibility for compliance
with applicable City of Wheat Ridge codes and ordinances for work under any permit issued based on this application; that I am the legal owner
or have been authorized by the legal owner of the property to perform the described work and am also authorized by the legal owner of any
entity included on this application to list that entity on this application. 1, the applicant for this building permit application, warrant the
truthfulness of the information provided on the application.
CIRCLE ONE: (OWNER) (CONTRACTOR) or (AUTHORIZED REPRESENTATIVE) of (OWNER) (CONTRACTOR)
Signature (first and last name):
� For BRS Field Ops LLC 02/11/2020
``�`d�' �����"""'"" DATE:
Printed Name: Linsey McClain
ZONING COMMMENTS:
Reviewer:
BUI5ee
G EPARTMENT COMMENTS:
Rev
PUBLIC WORKS COMMENTS:
Reviewer:
DEPARTMENT USE ONLY
OCCUPANCY CLASSIFICATION:
CONSTRUCTION TYPE:
Building Division Valuation:
1
VSE Project Number: U2001.1737.201
February 8, 2020
Blue Raven Solar, LLC O
ATTENTION: Carson Grover
1220 S. 630 E., Suite 430
American Fork, UT 84003
111mr,mamm
REFERENCE: Brenda Penner -Howell Residence (72118210): 8 Hillside Drive, Wheat Ridge, CO 80215
Solar Array Installation
To Whom It May Concern:
Per your request, we have reviewed the existing structure at the above referenced site. The purpose of our review was to
determine the adequacy of the existing structure to support the proposed installation of solar panels on the roof as shown on
the panel layout plan.
Based upon our review, we conclude that the existing structure is adequate to support the proposed solar panel installation.
Desi¢n Parameters
Code: International Building Code, 2012 Edition
Risk Category: II
Design wind speed: 125 mph (3 -sec gust) per ASCE 7-10
Wind exposure category: C
Ground snow load: 30 psf
Existime Roof Structure
Roof structure:'2-x8l rafters @ 24" O.C.
Roofing material: membrane
Connection to Roof
Mounting connection: (1) 5/16" lag screw w/ min. 2.5" embedment into framing at max. 48" O. . al ng rails
2 rails per row of panels, maximum panel height = 5'-6" °t
Conclusions 'fit
+ gu�ldin9 4iv�sion
Based upon our review, we conclude that the existing structure is adequate to support the proposed solar panel installation.
In the area of the solar array, other live loads will not be present or will be greatly reduced. The gravity loads, and thus the
stresses of the structural elements, in the area of the solar array are either decreased or increased by no more than 5%.
Therefore, the requirements of Section 3403.3 of the 2012 IBC are met and the structure is permitted to remain unaltered.
651 W. Galena Park Blvd., Ste. 101/ Draper, UT 84020! T (801) 990-1775 .' F (801) 990-1776 / WWW.vectorse .om
VSE Project Number: U2001.1737.201
a.
y Brenda Penner -Howell Residence
T2/8/2020
E n e i n E E R S
The solar array will be flush -mounted (no more than 6" above the roof surface) and parallel to the roof surface. Thus, we
conclude that any additional wind loading on the structure related to the addition of the proposed solar array is negligible.
The attached calculations verify the capacity of the connections of the solar array to the existing roof against wind (uplift),
the governing load case. Because the increase in lateral forces is less than 10%, this addition meets the requirements of the
exception in Section 3403.4 of the 2012 IBC. Thus the existing lateral force resisting system is permitted to remain
Limitations
Installation of the solar panels must be performed in accordance with manufacturer recommendations. All work performed
must be in accordance with accepted industry -wide methods and applicable safety standards. The contractor must notify
Vector Structural Engineering, LLC should any damage, deterioration or discrepancies between the as -built condition of the
structure and the condition described in this letter be found. Connections to existing roof framing must be staggered, except
at array ends, so as not to overload any existing structural member. The use of solar panel support span tables provided by
others is allowed only where the building type, site conditions, site-specific design parameters, and solar panel configuration
match the description of the span tables. The design of the solar panel racking (mounts, rails, etc.), and electrical engineering
is the responsibility of others. Waterproofing around the roof penetrations is the responsibility of others. Vector Structural
Engineering assumes no responsibility for improper installation of the solar array.
VECTOR STRUCTURAL ENGINEERING, LLC
Eric Sumsion_
LLC,CWS
OSY: AA.ce.Ce tB.t8:250TV
Eric Sumsion, P.E.
CO License: 56167 - Expires: 10/31/2021
Project Engineer
Enclosures
ESS/anr
Zoe
�G $t/!y �01Vf�
i
S 56167
x,02/08/2020
,, X
ky of
t Ridge -SG-'
ing
651 W. Galena Park Blvd., Ste. 101 / Draper, UT 84020 T (801) 990-1775 F (801) 990-1776 / www.vectorse.coni
TQ�
E n G 1 n E= E R S
PROJECT: Brenda Penner -Howell Residence
JOB NO.: U2001.1737.201
SUBJECT: WIND PRESSURE
Com onents and Cladding Wind Calculations
Label: ISolar Panel Array Note: Calculations per ASCE 7-10
SITE-SPECIFIC WIND PARAMETERS:
Basic Wind Speed [mph]: 125 Notes:
Exposure Category: C
Risk Category: II
ADDITIONAL INPUT & CALCULATIONS:
Height of Roof, h [ft]:
1s
(Approximate)
Comp/Cladding Location: Gable/Hip Roofs 7° < 0:5 27'
Enclosure Classification: Enclosed Buildings
Zone 1 GCP:
0.9
Figure 30.4-2B
Zone 2 GCP:
1.7
Zone 3 GCP:
2,6
a:
9.5
Table 26.9-1
z9 [ft]:
900
Table 26.9-1
Kh:
0.85
Table 30.3-1
KZc:
1
Equation 26.8-1
Kd:
0.85
Table 26.6-1
Velocity Pressure, qh [psf]:
28.9
Equation 30.3-1
GCP;:
0
Table 26.11-1
Hip?
(enter largest abs. value)
(enter largest abs. value)
(enter largest abs. value)
PRESSURES: I p = qh GCp — kLTCpi Equation 30.9-1
Zone 1, p [psf]: 26.0 psf (1.0 W, Interior Zones*)
Zone 2, p [psf]: 49.1 psf (1.0 W, End Zones*)
Zone 3, p [psf]: 75.0 psf (1.0 W, Corner Zones* within a)
(a= 3 ft)
M
TQR
E n s I n E E R S
PROJECT: Brenda Penner -Howell Residence
Lag Screw Connection
JOB NO.: U2001.1737.201
SUBJECT: CONNECTION
Capacity:
Demand:
29.4
4.0
Lag Screw Size [in]:
5/16
45.0
4.0
12.0
540
Cd:
1.6
NDS Table 2.3.2
Pressure
Max
Max. Trib.
2
Max. Uplift
(0.6 Wind)
Tributary
Area
Embedment' [in]:
2.5
(psf)
Width (ft)
(ft)
Force (lbs)
Grade:
SPF (G = 0.42)
Zone
Capacity [lbs/in]:
205
NDS Table 12.2A
1
15.6
4.0
12.0
187
Number of Screws:
1
2
3
Prying Coefficient: 1.4
Total Capacity [lbs]: 586
29.4
4.0
12.0
353
45.0
4.0
12.0
540
Demand< Capacity: CONNECTION OKAY
1. Embedment is measured from the top of the framing member to the beginning of the tapered tip of the lag screw.
Embedment in sheathing or other material is not effective. The length of the tapered tip is not part of the embedment
length.
2. 'Max. Trib Area' is the product of the'Max. Tributary Width' (along the rails) and 1/2 the panel width/height
(perpendicular to the rails).
T�
PROJECT: Brenda Penner -Howell Residence
CALCULATE ESTIMATED GRAVITY LOADS
ROOF DEAD LOAD (D)
Roof Pitch/12
1.7
Membrane
2.0
1/2" Plywood
1.0
Framing
3.0
Insulation
0.0
1/2" Gypsum Clg.
0.0
M, E & Misc
0.0
DL 6
PV Array DL 3
ROOF LIVE LOAD (L
Existing Design Roof Live Load [psf]
Roof Live Load With PV Array [psf]
SNOW LOAD (S):
Roof Slope [x:12]:
Roof Slope [°]:
Snow Ground Load, p9 [psf]:
Terrain Category:
Exposure of Roof:
Exposure Factor, Ce:
Thermal Factor, Ct:
Risk Category:
Importance Factor, Is:
Flat Roof Snow Load, pt [psf]:
Minimum Roof Snow Load, pm [psf]:
Unobstructed Slippery Surface?
Slope Factor Figure:
Roof Slope Factor, Cs:
Sloped Roof Snow Load, ps [psf]:
Design Snow Load, S [psf]:
JOB NO.: U2001.1737.201
SUBJECT: GRAVITY LOADS
Increase due to Original
pitch loading
1.01 2.0 psf
1.01 1.0 psf
psf
psf
psf
psf
psf
psf
20 ASCE 7-10, Table 4-1
0
w/ Solar Panel
Existing Array
1.7
1.7
8
8
30
30
C
C
Fully Exposed
Fully Exposed
0.9
0.9
1.1
1.1
II
II
1.0
1.0
21
21
20
20
No
No
Figure 7-2b
Figure 7-2b
1.00
1.00
21
21
21
21
ASCE 7-10, Section 7.2
ASCE 7-10, Table 7-2
ASCE 7-10, Table 7-2
ASCE 7-10, Table 7-2
ASCE 7-10, Table 7-3
ASCE 7-10, Table 1.5-1
ASCE 7-10, Table 1.5-2
ASCE 7-10, Equation 7.3-1
ASCE 7-10, Section 7.3.4
SV
ASCE-1 ",� ection 7.4
ASFEig?ure-,7'-2 "'199'7.4
AS
AS����
Q
W
m
F-
U
W
Co
N
Of
w
W
H
Ix
U
O
�
J
J
J
3
r
C)
W
W
W
W
(D
_
W
O
W
O
U)
CO
C/)
r
N
3
o
LO
`-
m
CO
CO
O
X
X
X
Co
It
Ln
'IT
>
n N
00
>
LL
N
6
J
O
N
J
M
J
W
°c
W
Q
W
a
°LL
Q'
O
O
N
.fl
�
>
1- C
n N
>CO
N
>
J
v
>
J
cn
J
m
H
Cn
o
F
Cn
0
Lo
H
0
Q
W
m
F-
U
W
Co
N
Of
w
W
H
Ix
U
(3) 00
N X
(n N
(1) N
LL
(0 LL
d
U)
# PLIES
c� Co
0
a. C) J a
0- J JO a
React (A, B)
M o
CL J LL
O
7 Cu «-
Cn J Q
_0 > p
G '7i -
a{
wheat R�d9e
on
• gui\d1n9
O
�
N
3
r
C)
00
C7
>
r
N
3
o
LO
`-
m
x
E i
N
Q'
N
.fl
�
m
O
N
U
LO
17
o
U
17
U
`—
D CRITERIA
(3) 00
N X
(n N
(1) N
LL
(0 LL
d
U)
# PLIES
c� Co
0
a. C) J a
0- J JO a
React (A, B)
M o
CL J LL
O
7 Cu «-
Cn J Q
_0 > p
G '7i -
a{
wheat R�d9e
on
• gui\d1n9
GENERAL NOTES
CODES AND STANDARDS
1. ALL WORK SHALL COMPLY WITH 2017 NATIONAL ELECTRIC CODE (NEC), 2015
INTERNATIONAL BUILDING CODE (IBC), 2015 INTERNATIONAL RESIDENTIAL CODE (IRC), 2015
INTERNATIONAL PLUMBING CODE (IPC), AND ALL STATE AND LOCAL BUILDING, ELECTRICAL,
AND PLUMBING CODES.
2. DRAWINGS HAVE BEEN DETAILED ACCORDING TO UL LISTING REQUIREMENTS.
SITE NOTES / OSHA REGULATION
1 A LADDER SHALL BE IN PLACE FOR INSPECTION IN COMPLIANCE WITH OSHA REGULATIONS.
2. THE PV MODULES ARE CONSIDERED NON-COMBUSTIBLE AND THIS SYSTEM IS AN UTILITY
INTERACTIVE SYSTEM WITH NO STORAGE BATTERIES.
3. THE SOLAR PV INSTALLATION SHALL NOT OBSTRUCT ANY PLUMBING, MECHANICAL, OR
BUILDING ROOF VENTS.
4. ROOF COVERINGS SHALL BE DESIGNED, INSTALLED, AND MAINTAINED IN ACCORDANCE WITH
THIS CODE AND THE APPROVED MANUFACTURER'S INSTRUCTIONS SUCH THAT THE ROOF
COVERING SHALL SERVE TO PROTECT THE BUILDING OR STRUCTURE.
SOLAR CONTRACTOR
1. MODULE CERTIFICATIONS WILL INCLUDE UL1703, IEC61646, IEC61730
2. IF APPLICABLE, MODULE GROUNDING LUGS MUST BE INSTALLED AT THE MARKED GROUNDING
LUG HOLES PER THE MANUFACTURERS' INSTALLATION REQUIREMENTS
3. AS INDICATED BY DESIGN: OTHER NRTL LISTED MODULE GROUNDING DEVICES MAY BE USED
IN PLACE OF STANDARD GROUNDING LUGS AS SHOWN IN MANUFACTURER DOCUMENTATION
AND APPROVED BY THE AHJ
4. CONDUIT AND WIRE SPECIFICATIONS ARE BASED ON MINIMUM CODE REQUIREMENTS AND ARE
NOT MEANT TO LIMIT UP-SIZING AS REQUIRED BY FIELD CONDITIONS.
5. CONDUIT POINT OF PENETRATION FROM EXTERIOR TO INTERIOR TO BE INSTALLED AND
SEALED WITH A SUITABLE SEALING COMPOUND.
6. DC WIRING LIMITED TO MODULE FOOTPRINT W/ ENPHASE AC SYSTEM.
7. ENPHASE WIRING SYSTEMS SHALL BE LOCATED AND SECURED UNDER THE ARRAY W/
SUITABLE WIRING CLIPS.
8. MAX DC VOLTAGE CALCULATED USING MANUFACTURER PROVIDED TEMP COEFFICIENT FOR
VOC UNLESS NOT AVAILABLE.
9. ALL INVERTERS, MOTOR GENERATORS, PHOTOVOLTAIC MODULES, PHOTOVOLTAIC PANELS,
AC PHOTOVOLTAIC MODULES, DC COMBINERS, DC -TO -DC CONVERTERS,SOURCE CIRCUIT
COMBINERS, AND CHARGE CONTROLLERS INTENDED FOR USE IN A PHOTOVOLTAIC POWER SYSTEM
WILL BE IDENTIFIED AND LISTED FOR THE APPLICATION PER 690.4 (B).
10. ALL SIGNAGE TO BE PLACED IN ACCORDANCE WITH LOCAL BUILDING CODE.
11. TERMINALS AND LUGS WILL BE TIGHTENED TO MANUFACTURER TORQUE SPECIFICATIONS (WHEN
PROVIDED) IN ACCORDANCE WITH NEC CODE 110.14(D) ON ALL ELECTRICAL CONNECTIONS.
EQUIPMENT LOCATIONS
1, PROPER ACCESS AND WORKING CLEARANCE AROUND EXISTING AND PROPOSED ELECTRICAL
EQUIPMENT WILL BE PROVIDED AS PER SECTION [NEC 110.261.
2. EQUIPMENT INSTALLED IN DIRECT SUNLIGHT MUST BE RATED FOR EXPECTED OPERATING
TEMPERATURE AS SPECIFIED BY [NEC 690.31 (A) -(B)] AND [NEC TABLE 310.15 (B)].
3. ADDITIONAL AC DISCONNECTS SHALL BE PROVIDED WHERE THE INVERTER IS NOT ADJACENT
TO THE UTILITY AC DISCONNECT, OR NOT WITHIN SIGHT OF THE UTILITY AC DISCONNECT.
4, ALL EQUIPMENT SHALL BE INSTALLED ACCESSIBLE TO QUALIFIED PERSONNEL ACCORDING TO
NEC APPLICABLE CODES.
5. ALL COMPONENTS ARE LISTED FOR THEIR PURPOSE AND RATED FOR OUTDOOR USAGE WHEN
APPROPRIATE.
VECTOR
E n O I In E E R 9
651 W. GALENA PARK BLVD. ST£. 701 PHONE (60 7) 990- 7 775
DRAPER, UTAH 64020 WWW. VEDTORSE. COM
Eric SumsionfiA�'
Vector Structural Engineering has reviewed the existing structure
with loading from the solar array and lag screw connections to the
existing framing. The design of the racking system, connections,
and all other structure is by others. Mechanical, architectural, and
all other nonstructural aspects of the design are by others.
Electrical is by others, unless stamped by Dean Levorsen.
;5.06 •s�.sFo
M .
56167
02/08/2020 •jef
•
10•••9••00••• \\
VSE Project Number: U2001-1737-201
APPIAI \/IG1A/
r7Z7- r
LHI i �
DESIGN CRITERIA SITE SPECIFICATIONS
WIND SPEED: 125 MPH OCCUPANCY -R3
GROUND SNOW LOAD: 30 PSF CONSTRUCTION - V -B
WIND EXPOSURE FACTOR: C ZONING: RESIDENTIAL
SEISMIC DESIGN CATEGORY: B
SCOPE OF WORK
INSTALLATION OF UTILITY INTERACTIVE PHOTOVOLTAIC SOLAR SYSTEM
4.27 kW DC PHOTOVOLTAIC SOLAR ARRAY
ROOF TYPE: Mod Bitumen / Rolled Comp
MODULES: (14) Seraphim SEG-6MB-305BB
INVERTER(S): Enphase IQ7-60-2-US,----
RACKING: Unirac SolarMount LT
#co,LD ol-D 00 S1 03
BLUE RAVEN
1403 N RESEARCH WAY, BUILDING J
OREM, UT 84097
800-377-4480
W W W.BLUERAVENSOLAR.COM
r.- \
{�CERTIFIEbl
PV INSTALLATION
PROFESSIONAL
Scott Gurney
y^ # PV -011719-015866
CONTRACTOR:
EIRS FIELD OPS
385.498.6700
Approval Notes:
1) PV array system to have grounding system installed per Part III
of Article 250 per 2017 NEC Art.690.47(A)
2) If UFER ground is not available provide or verify supplemental
ground rods per 2017 NEC Art.250.104(B)
3) Natural Gas piping to be bonded per 2017 NEC Art. 250.104(B).
SHEET INDEX AppROVEU AS
-
PV1 - COVER SHEET
PV2 - PROPERTY F'LeMT td for Code ComalE _,
PV3 -SITE P
PV4 - EQUPICAL
ENT DETAIL
PV5 - ELEE �(
PV6 - ELEALC ON "1010'
ELEOTES
PV7 - MAIN BREAKER DERATE CALCS.
(IF NEEDED)
PV8 - LABELS & LOCATIONS
PV9 - CUSTOM DIRECTORY PLACARD
(IF NEEDED - NEC 690.56(B))
05EOdG
CONFIDENTIAL - THE INFORMATION
HEREIN CONTAINED SHALL NOT BE
USED FOR THE BENEFIT OF
ANYONE EXCEPT
BLUERAVENSOLAR NOR SHALL IT
BE DISCLOSED IN WHOLE OR IN
PART TO OTHERS OUTSIDE
`
RECIPIENTS ORGANIZATION,
EXCEPT IN CONNEC TION WITH THE
SALE AND USE OF THE RESPECTIVE
EQUIPMENT, WITHOUT THE
WRITTEN PERMISSION OF
.,
BLUERAVENSOLAR LLC.
r.- \
{�CERTIFIEbl
PV INSTALLATION
PROFESSIONAL
Scott Gurney
y^ # PV -011719-015866
CONTRACTOR:
EIRS FIELD OPS
385.498.6700
Approval Notes:
1) PV array system to have grounding system installed per Part III
of Article 250 per 2017 NEC Art.690.47(A)
2) If UFER ground is not available provide or verify supplemental
ground rods per 2017 NEC Art.250.104(B)
3) Natural Gas piping to be bonded per 2017 NEC Art. 250.104(B).
SHEET INDEX AppROVEU AS
-
PV1 - COVER SHEET
PV2 - PROPERTY F'LeMT td for Code ComalE _,
PV3 -SITE P
PV4 - EQUPICAL
ENT DETAIL
PV5 - ELEE �(
PV6 - ELEALC ON "1010'
ELEOTES
PV7 - MAIN BREAKER DERATE CALCS.
(IF NEEDED)
PV8 - LABELS & LOCATIONS
PV9 - CUSTOM DIRECTORY PLACARD
(IF NEEDED - NEC 690.56(B))
05EOdG
DRAWING BY
DIN ENGINEERING
DATE
February 4, 2020
PROJECT NUMBER
72118210
SHEET NAME
COVER SHEET
PAGE NUMBER REVISION
F 0
LID
N
O
CO
O
Z
0
7
O
(>3
O
O
U
O
aa)i
a
LL.
Z
a-
0
m
U)mc�
DRAWING BY
DIN ENGINEERING
DATE
February 4, 2020
PROJECT NUMBER
72118210
SHEET NAME
COVER SHEET
PAGE NUMBER REVISION
F 0
9'-11"
11
DC SYSTEM SIZE: 4.27 kW DC
ROOF TYPE: Mod Bitumen / Rolled Comp
(14) Seraphim SEG-6MB-305BB
Enphase IQ7-60-2-US,----INVERTER
8 Hillside Drive
R -'V-711
124'-6"
11
i 1:r1_C:nin
INV
INVERTER & DC DISCONNECT
[TU J
(E) SUBPANEL
LC
(N) LOAD CENTER
AC
AC DISCONNECT
❑M
UTILITY METER
MSP
MAIN SERVICE PANEL
JB
JUNCTION BOX
TS
TRANSFER SWITCH
C❑
COMBINER BOX/AGGREGATOR
PV
PV REVENUE METER
®
FIRE SETBACK
EMT CONDUIT RUN
(TO BE DETERMINED IN FIELD)
PV WIRE STRING
PROPERTY LINE
SCALE: 1/16" = V-0"
16 2'
1403 N RESEARCH WAY, BUILDING J
OREM, UT 84097
800-377-4480
WWW BLUERAVENSOLAR.COM
CONFIDENTIAL - THE INFORMATION
HEREIN CONTAINED SHALL NOT BE
USED FOR THE BENEFIT OF
ANYONE EXCEPT
BLUERAVENSOLAR NOR SHALL IT
BE DISCLOSED IN WHOLE OR IN
PART TO OTHERS OUTSIDE
RECIPIENTS ORGANIZATION,
EXCEPT IN CONNEC TION WITH THE
SALE AND USE OF THE RESPECTIVE
EQUIPMENT, WITHOUT THE
WRITTEN PERMISSION OF
BLUERAVENSOLAR LLC.
CERTIFIED
PV INSTALLATION
PROFESSIONAL
Scott Gurney
# PV -011719-015866
CONTRACTOR:
BRS FIELD OPS
385.498.6700
DATE
February 4, 2020
PROJECT NUMBER
72118210
SHEET NAME
PROPERTY PLAN
PAGE NUMBER REVISION
PV2 0
U
n
_�
N
CD
�C
00
r
O
N
Z
C
L
O
w
I—
=
o
N
Q
U
�
LL
C:
-C:
(D
C)
2
G
M
ILLO
Z
LL
TQ
Vry
VJ
_
W
—
N
(n
^c
V/
W
CID
BY
DIN ENGINEERING
DATE
February 4, 2020
PROJECT NUMBER
72118210
SHEET NAME
PROPERTY PLAN
PAGE NUMBER REVISION
PV2 0
19
CHIMNEY
FRONT OF HOME
DC SYSTEM SIZE: 4.27 kW DC
ROOF TYPE: Mod Bitumen / Rolled Comp
(14) Seraphim SEG-6MB-305BB
Enphase IQ7-60-2-US,----INVERTER
ALIIVIU I h:"I 10
PITCH:8D
TSRF:80%
AREA: 431.95 SQ. FT
321-611
Eric Sumsion�s,A
LEGEND
INV
INVERTER & DC DISCONNECT
SUB
(E) SUBPANEL
LC
(N) LOAD CENTER
AC
AC DISCONNECT
❑M
UTILITY METER
MSP
MAIN SERVICE PANEL
JB
JUNCTION BOX
TS
TRANSFER SWITCH
C❑
COMBINER BOX/AGGREGATOR
PV
PV REVENUE METER
®
FIRE SETBACK
-0
EMT CONDUIT RUN
(TO BE DETERMINED IN FIELD)
PV WIRE STRING
PROPERTY LINE
BLUE RAVEN
1403 N RESEARCH WAY, BUILDING J
OREM, UT 84097
800-377-4480
W W W. BLUERAV ENSOLAR.COM
CONFIDENTIAL - THE INFORMATION
HEREIN CONTAINED SHALL NOT BE
USED FOR THE BENEFIT OF
ANYONE EXCEPT
BLUERAVENSOLAR NOR SHALL IT
BE DISCLOSED IN WHOLE OR IN
PART TO OTHERS OUTSIDE
RECIPIENTS ORGANIZATION,
EXCEPT IN CONNEC TION WITH THE
SALE AND USE OF THE RESPECTIVE
EQUIPMENT, WITHOUT THE
WRITTEN PERMISSION OF
BLUERAVENSOLAR LLC.
CERTIFIED
PV INSTALLATION
PROFESSIONAL
Scott Gurney
# PV -011719-015866
SCALE: 1/8" = V-0" CONTRACTOR:
0 z a a 16 BRS FIELD OPS
385.498.6700
VECTOR
E n O I n E E R S
657 W. GALENA PARK BLVD. STE. 101 PHONE (807) 990-1
DRAPER, UTAH 84020 WWW.VECTORSE
��PDO tie
FSG Su�S�O'
Z
56167
02/08/2020 J
AL
VSE Project Number: U2001-1737-201
Vector Structural Engineering has reviewed the existing structure
with loading from the solar array and lag screw connections to the
existing framing. The design of the racking system, connections,
and all other structure is by others. Mechanical, architectural, and
all other nonstructural aspects of the design are by others.
Electrical is by others, unless stamped by Dean Levorsen.
SWING BY
DATE
ERING
February 4, 2020
PROJECT NUMBER
72118210
SHEET NAME
SITE PLAN
PAGE NUMBER REVISION
PV3 0
L0
T-
N
O
00
Z
0_O
O
CU
O
H 2
Q L
0
0
N C'L
1..10-
m
N
aai
�
-0
LL
z co
-0
�.
W a,
°
U) in...
A
SWING BY
DATE
ERING
February 4, 2020
PROJECT NUMBER
72118210
SHEET NAME
SITE PLAN
PAGE NUMBER REVISION
PV3 0
PV ARRAY INFORMATION PV4 PV MODULE PV4
Unirac SolarMount LT RAIL BLUE RAVEN
PV MODULE COUNT: 14 MODULES
# OF ATTACHMENT POINTS: 26
ARRAY AREA: Module Count x 17.51 ft2 = 245.1 ft2
ROOF AREA: 2383.3ft2
% OF ARRAY/ROOF: 10.3%
ARRAY WEIGHT: Module Count x 50lbs = 700.Olbs
DISTRIBUTED LOAD: Array Weight _ Array Area = 2.86 Ibs/ft2
POINT LOAD: Array Weight _ Attachments = 26.9lbs/attachment
UNIRAC PRO SERIES
END CLAMP
PV MODULE
UNIRAC RAIL
G DETAIL, END CLAMP FRONT
Scale: 3" = V-0"
UNIRAC SM L -FOOT
ECOFASTEN SIMPLE
GRIP SQ STANDOFF
RAC PRO SERIES
CLAMP
PV MODULE
UNIRAC RAIL
DETAIL, MID CLAMP FRONT
E T
Scale: 3" = V-0"
Dv Mrlrll II C
EG-6MB-305BB
�J Scale: 3" = V-0"
iolarMount LT RAIL
N) ROOF LEVEL
IASTIC
(E) ROOF
MEMBRANE
i
W DP 15-13X03
T_48" MAX.
MAX.
LANDSCAPE
PORTRAIT
ARRAY DETAIL, FRONT VIEW
Scale: 3/8" = 1'-0"
PORTRAIT
LANDSCAPE
ARRAY DETAIL, SIDE VIEW
Scale: 3/8" = V-0"
RACKING ATTACHMENTS TO BE
STAGGERED BY SHIFTING EACH
SUBSEQUENT ROW OF ATTACHMENTS
ONE RAFTER OVER.
10" MIN -
1'-4"
MAX
MIN.
10"MIN -
V-4"
MAX
ECOFASTEN Simplegrip-SQ
ROOF TYPE: Mod Bitumen / Rolled Comp
ROOF FRAMING TYPE: Rafter
RAFTER OR TOP CHORD(TRUSS) 2x8 @ 24"O.C.
CEILING JOIST OR BOTTOM CHORD(TRUSS) None @---"O.C.
sm,E,,�sm
Eric SumsionaA
u�
VECTOR
E n O I n E E R 9
651 W. GALENA PARK BLVD. STE. 701 PHONE (BO 1 ) 9570-177-9
DRAPER, UTAH B4020 WWW.__R5E. COM
o���Poo �icF�s
V .•,G S�Ms'•.FO
56167 i
02/08/2020 •��
S/0NA1_ EAG
VSE Project Number: U2001-1737-201
Vector Structural Engineering has reviewed the existing structure
with loading from the solar array and lag screw connections to the
existing framing. The design of the racking system, connections,
and all other structure is by others. Mechanical, architectural, and
all other nonstructural aspects of the design are by others.
Electrical is by others, unless stamped by Dean Levorsen.
1403 N RESEARCH WAY, BUILDING J
OREM, UT 84097
800-377-4480
WWW. BLUERAVENSOLAR.COM
CONFIDENTIAL -THE INFORMATION
HEREIN CONTAINED SHALL NOT BE
USED FOR THE BENEFIT OF
ANYONE EXCEPT
BLUERAVENSOLAR NOR SHALL IT
BE DISCLOSED IN WHOLE OR IN
PART TO OTHERS OUTSIDE
RECIPIENTS ORGANIZATION,
EXCEPT IN CONNEC TION WITH THE
SALE AND USE OF THE RESPECTIVE
EQUIPMENT, WITHOUT THE
WRITTEN PERMISSION OF
BLUERAVENSOLAR LLC.
r
�CERTIFIEb�
PV INSTALLATION
PROFESSIONAL
Scoff Gurney
# PV -011719-015866
CONTRACTOR:
BRS FIELD OPS
385.498.6700
U
LO >0
CV
February 4, 2020
PROJECT NUMBER
72118210
SHEET NAME
EQUIP. DETAIL
PAGE NUMBER REVISION
PV4 0
O �G
00 ti
O N
Z
O
O 6i
H
Z
o N
<�
r`
Cu
U UC)
r..L
C:
LG
LL
C
C)
C
CU
F—
z
-
c
W
c
=
Cu to
(F)
Y
co
3: Q
February 4, 2020
PROJECT NUMBER
72118210
SHEET NAME
EQUIP. DETAIL
PAGE NUMBER REVISION
PV4 0
PV BREAKER TO BE LOCATED OPPOSITE
END OF BUSSING FROM MAIN BREAKER
(E) GROUNDING
ELECTRODE (S)
Approval Notes:
1) PV array system to have grounding system installed per Part III
of Article 250 per 2017 NEC Art.690.47(A)
2) If UFER ground is not available provide or verify supplemental
ground rods per 2017 NEC Art.250.104(B)
3) Natural Gas piping to be bonded per 2017 NEC Art. 250.104(B)
INTERCONNECTION NOTES
1. ONE OF THE METHODS THAT FOLLOWS SHALL BE USED TO DETERMINE THE RATINGS OF
BUSBARS AND PANELBOARDS. (a) THE SUM OF 125 PERCENT OF THE INVERTER(S) OUTPUT
CIRCUIT CURRENT AND THE RATING OF THE OVERCURRENT DEVICE PROTECTING THE
BUSBAR SHALL NOT EXCEED THE AMPACITY OF THE BUS BAR. (b) WHERE TWO SOURCES,
ONE THE UTILITY AND THE OTHER AN INVERTER ARE LOCATED AT OPPOSITE ENDS OF A
BUSBAR THAT CONTAINS LOADS, THE SUM OF 125 PERCENT OF THE INVERTER(S) OUTPUT
CIRCUIT CURRENT AND THE RATING OF THE OVERCURRENT DEVICE PROTECTING THE
BUSBAR SHALL NOT EXCEED 120 PERCENT OF THE AMPACITY OF THE BUSBAR [NEC 705.12].
PV Production meter notes:
1. The self-contained metering will be in compliance
with the most recent revision of the Xcel
Energy Standard; specifically Section 4.11.
2. The PV production meter will be required to have
the PV generation wired to the line side terminals
(top of meter block).
3. The meter socket for the PV production meter shall
be marked with a stamped brass, aluminum, or
stainless steel tag, indicating the address including
the unit, typically "PV PROD" in accordance with
the requirements for "Meter Identification" in Section
4.14.4 of the Xcel Energy Standard.
4. The PV production meter shall be located within
ten (10) feet of the existing utility meter. If there
is any reason this cannot be accomplished, a site
plan showing proposed equipment locations
shall be submitted for review. The local meter
shop must approve the site plan for application
approval; site meetings can be arranged upon
request.
NOTE TO INSTALLER: The current Placard that we require
at the utility meter and AC Disconnect is a yellow with black
lettering
X
(1) 10 AWG THHN/THWN-2, CU., BLACK (Ll) 14.0 A AC
(1) 10 AWG THHN/THWN-2, CU., BLACK (Ll) MAX 14.0 A A
(1) 10 AWG THHN/THWN-2, CU., BLACK (Ll)
MAX 14.0 A A
(1) 12-2 TC-ER,THHN/THWN-2, CU. MAX 14.0 A AC
(1) 10 AWG THHN/THWN-2, CU., RED (1-2) 240 V AC
3
(1) 10 AWG THHN/THWN-2, CU., RED ( L 2) 240 V A
2 (1) 10 AWG THHN/THWN-2, CU., RED (L2)
240 V AC
1
(1) 6 AWG BARE, CU (EGC) 240 V AC
15
�C
10 AWG THHN/THWN-2, CU., GREEN
(1) 10 AWG THHN/THWN-2, CU., GREEN (EGC)
co
Nor -
(1) 10 AWG THHN/THWN-2, CU., WHITE (N)
CV
(1) (EGC)
2
a)
a
>
CU
0
U
M
N
C/)
CC
LIJ
(1_
>
U)
(n
m _
(1) 10 AWG THHN/THWN-2, CU., GREEN (EGC)
(1) 3/4 INCH EMT EXTERIOR
OR 10- 2 OF -B W/G, THHN/THWN-2, SOLID CU.
(1) 3/4 INCH EMT EXTERIOR
OR 10- 2 OF -B W/G, THHN/THWN-2, SOLID
(1) 3/4 INCH EMT
CU.
EXTERIOR
EXTERIOR
BLUE RAVEN
1. ALL
CONDUIT TO BE RAN AT LEAST 7/8" ABOVE ROOF SURFACE WHERE EXPOSED TO SUNLIGHT.
2. TERMINALS AND LUGS WILL BE TIGHTENED TO MANUFACTURER TORQUE SPECIFICATIONS (WHEN
1403 N RESEARCH WAY, BUILDING J
PROVIDED) IN ACCORDANCE WITH NEC CODE 110.14(D) ON ALL ELECTRICAL CONNECTIONS.
3. CONDUIT
AND CONDUCTOR SPECIFICATIONS ARE BASED ON MINIMUM CODE REQUIREMENTS AND
OREM, UT 84097
ARE
NOT MEANT TO LIMIT UP-SIZING AS REQUIRED BY FIELD CONDITIONS.
800-377-4480
WWW. BLUERAVENSOLAR.COM
CONFIDENTIAL - THE INFORMATION
HEREIN CONTAINED SHALL NOT BE
USED FOR THE BENEFIT OF
ANYONE EXCEPT
BLUERAVENSOLAR NOR SHALL IT
BE DISCLOSED IN WHOLE OR IN
PART TO OTHERS OUTSIDE
RECIPIENTS ORGANIZATION,
EXCEPT IN CONNEC TION WITH THE
SALE AND USE OF THE RESPECTIVE
EQUIPMENT, WITHOUT THE
WRITTEN PERMISSION OF
(E)200A MAIN SERVICE PANEL
(14) Seraphim SEG-6MB-3058B SEG--3058B
BLUERAVENSOLAR LLC.
(E)200A / 2P MAIN BREAKER UTILITY PV
Enphase IQ Combiner 3
'JUNCTION
UL 1703 COMPLIANT
---
PRODUCTION
(E PV AC DISCONNECT
X -IQ -AMI -240-3
FOR WIRE SPLLICINGICING
(14) Enphase IQ7-60-2-US MICRO INVERTERS
METER 200A
LEVER BYPASS NON- FUSED
(SOLAR LOADS ONLY)
ONLY -OPTIONAL IF
UL 1741 COMPLIANT
(E)200A / 2P
METER SOCKET LOCKABLE, VISIBLE OPEN
Q -CABLE (TC -ER) OR
7 MODULES MAX FOR ALL SUB -BRANCH
30A, 240V, 2 -POLE
OF -B USED FOR
CIRCUIT(S) TO COMPLY WITH VRISE CALCS
CERTIFIED
ENTIRE HOMERUN
PV INSTALLATION
(E)LOADS N
N JUNCTION BOX
JUNCTION BOX
PROFESSIONAL
Scott Gurney
(1) CIRCUIT -
# PV -011719-015866
(N)20A/2P
(N)20A/ P
Ll uu
OF 14 MODULES
�_ �Z
CONTRACTOR:
�
BRS FIELD OPS
N EGC G
G G
G
385.498.6700
120/240 VAC
60HZ
1 PHASE
TO UTILITY J 15 ENPHASE COMBINER BOX WILL BE
3
2 1
GRID G ACCESSIBLE TO UTILITY COMPANY 24/7
PV BREAKER TO BE LOCATED OPPOSITE
END OF BUSSING FROM MAIN BREAKER
(E) GROUNDING
ELECTRODE (S)
Approval Notes:
1) PV array system to have grounding system installed per Part III
of Article 250 per 2017 NEC Art.690.47(A)
2) If UFER ground is not available provide or verify supplemental
ground rods per 2017 NEC Art.250.104(B)
3) Natural Gas piping to be bonded per 2017 NEC Art. 250.104(B)
INTERCONNECTION NOTES
1. ONE OF THE METHODS THAT FOLLOWS SHALL BE USED TO DETERMINE THE RATINGS OF
BUSBARS AND PANELBOARDS. (a) THE SUM OF 125 PERCENT OF THE INVERTER(S) OUTPUT
CIRCUIT CURRENT AND THE RATING OF THE OVERCURRENT DEVICE PROTECTING THE
BUSBAR SHALL NOT EXCEED THE AMPACITY OF THE BUS BAR. (b) WHERE TWO SOURCES,
ONE THE UTILITY AND THE OTHER AN INVERTER ARE LOCATED AT OPPOSITE ENDS OF A
BUSBAR THAT CONTAINS LOADS, THE SUM OF 125 PERCENT OF THE INVERTER(S) OUTPUT
CIRCUIT CURRENT AND THE RATING OF THE OVERCURRENT DEVICE PROTECTING THE
BUSBAR SHALL NOT EXCEED 120 PERCENT OF THE AMPACITY OF THE BUSBAR [NEC 705.12].
PV Production meter notes:
1. The self-contained metering will be in compliance
with the most recent revision of the Xcel
Energy Standard; specifically Section 4.11.
2. The PV production meter will be required to have
the PV generation wired to the line side terminals
(top of meter block).
3. The meter socket for the PV production meter shall
be marked with a stamped brass, aluminum, or
stainless steel tag, indicating the address including
the unit, typically "PV PROD" in accordance with
the requirements for "Meter Identification" in Section
4.14.4 of the Xcel Energy Standard.
4. The PV production meter shall be located within
ten (10) feet of the existing utility meter. If there
is any reason this cannot be accomplished, a site
plan showing proposed equipment locations
shall be submitted for review. The local meter
shop must approve the site plan for application
approval; site meetings can be arranged upon
request.
NOTE TO INSTALLER: The current Placard that we require
at the utility meter and AC Disconnect is a yellow with black
lettering
X
PROJECT NUMBER
72118210
SHEET NAME
ELEC. 3 LINE DIAL.
PAGE NUMBER REVISION
PV5 0
L0
N
O
�C
co
O
CV
Z
OLLI
H
Q
N
O
Z
LLl
2
a)
a
>
CU
0
U
M
N
C/)
CC
LIJ
(1_
>
U)
(n
m _
CO
PROJECT NUMBER
72118210
SHEET NAME
ELEC. 3 LINE DIAL.
PAGE NUMBER REVISION
PV5 0
MUUULt JPt(-!FI(_A I IUNJ Seraphim 5tL3-bMb-.iU!)bb
RATED POWER (STC)
305 W
MODULE VOC
39.9 V DC
MODULE VMP
32.3 V DC
MODULE IMP
9.45 A DC
MODULE ISC
9.76 A DC
VOC CORRECTION
-0.28 %/-C
VMP CORRECTION
-0.38 %/°C
SERIES FUSE RATING
20 A DC
ADJ. MODULE VOC @ ASHRAE LOW TEMP
44.3 V DC
ADJ. MODULE VMP @ ASHRAE 2% AVG. HIGH TEMP
27.4 V DC
MICROINVEK IEK SPECIFICA HUNS
Enpnase IQ/-bU-Z-US
POWER POINT TRACKING (MPPT) MIN/MAX
22 - 48 V DC
MAXIMUM INPUT VOLTAGE
48 V DC
MAXIMUM DC SHORTCIRCUIT CURRENT
15 A DC
MAXIMUM USABLE DC INPUT POWER
350 W
MAXIMUM OUTPUT CURRENT
1 A AC
AC OVERCURRENT PROTECTION
20 A
MAXIMUM OUTPUT POWER
240 W
CEC WEIGHTED EFFICIENCY
97%
AC PHO (UVULA HC MUUULt MAKKING (NEL b9U.SZ)
NOMINAL OPERATING AC VOLTAGE
240 V AC
NOMINAL OPERATING AC FREQUENCY
47- 68 HZ AC
MAXIMUM AC POWER
240 VA AC
MAXIMUM AC CURRENT
1.0 A AC
MAXIMUM OCPD RATING FOR AC MODULE
20 A AC
DESIGN LOCATION AND TEMPERATURES
TURE DATA SOURCE
ATE
1EATHER STATION
SHRAE EXTREME LOW TEMP (°C)
SHRAE 2% AVG. HIGH TEMP (°C)
ASHRAE 2% AVG. HIGH TEMP
Colorado
Wheat Ridge
SALISBURY WICOMICO CO AP
33
SYSTEM ELECTRICAL SPECIFICATIONS CIR 1 CIR 2 CIR 3 CIR 4 CIR 5 CIR 6
NUMBER OF MODULES PER MPPT
DC POWER RATING PER CIRCUIT (STC)
TOTAL MODULE NUMBER
STC RATING OF ARRAY
AC CURRENT @ MAX POWER POINT (IMP
MAX. CURRENT (IMP X 1.25)
OCPD CURRENT RATING PER CIRCUIT
MAX. COMB. ARRAY AC CURRENT (IMP)
MAX. ARRAY AC POWER
14
4270
COND.
JRISE(V) VEND(V;
%VRISE IQ7-7
VRISE SEC. 1(MICRO TO 160X)
25.2
14 MODULES
4270W DC
14.0
17.5
20
0.30%
VRISE SEC. 2 (J BOX TO COMBINER BOX)
30
10 Cu.
1.07
14.0
3360W AC
AC VOLTAGE RISE CALCULATIONS
DIST (FT)
COND.
JRISE(V) VEND(V;
%VRISE IQ7-7
VRISE SEC. 1(MICRO TO 160X)
25.2
12 Cu.
0.71
240.71
0.30%
VRISE SEC. 2 (J BOX TO COMBINER BOX)
30
10 Cu.
1.07
241.07
0.44%
VRISE SEC. 3 (COMBINER BOX TO POI)
10
10 Cu.
0.36
240.36
0.15%
TOTALVRISE
JUNCTION BOX TO
MAX. SHORT CIRCUIT CURRRENT (ISC) =
2.14
242.14
0.89°/
PHOTOVOLTAIC AC DISCONNECT OUTPUT LABEL (NEC 690.54)
AC OUTPUT CURRENT 14.0 A AC
NOMINAL AC VOLTAGE 240 V AC
GROUNDING NOTES
1. A GROUNDING ELECTRODE SYSTEM IN ACCORDANCE WITH [NEC 690-47] AND
[NEC 250-501 THROUGH [NEC 250-601 SHALL BE PROVIDED. PER NEC,
GROUNDING ELECTRODE SYSTEM OF EXISTING BUILDING MAY BE USED AND
BONDED TO AT THE SERVICE ENTRANCE. IF EXISTING SYSTEM IS INACCESSIBLE,
OR INADEQUATE, OR IS ONLY METALLIC WATER PIPING, A SUPPLEMENTAL
GROUNDING ELECTRODE WILL BE USED AT THE INVERTER LOCATION
CONSISTING OF A UL LISTED 8 FT GROUND ROD WITH ACORN CLAMP.
2. THE GROUNDING ELECTRODE CONDUCTOR SHALL BE PROTECTED FROM PHYSICAL
DAMAGE BETWEEN THE GROUNDING ELECTRODE AND THE PANEL (OR INVERTER) IF
SMALLER THAN #6 AWG COPPER WIRE PER NEC 250-64B. THE GROUNDING ELECTRODE
CONDUCTOR WILL BE CONTINUOUS, EXCEPT FOR SPLICES OR JOINTS AT BUSBARS
WITHIN LISTED EQUIPMENT PER [NEC 250.64C.].
3. GROUNDING ELECTRODE CONDUCTORS SHALL BE NO LESS THAN #8 AWG AND
NO GREATER THAN #6 AWG COPPER AND BONDED TO THE EXISTING GROUNDING
ELECTRODE TO PROVIDE FOR A COMPLETE SYSTEM,
4. PV SYSTEM SHALL BE GROUNDED IN ACCORDANCE TO [NEC 250.211, [NEC TABLE
250.1221, AND ALL METAL PARTS OR MODULE FRAMES ACCORDING TO [NEC
690.46].
5. MODULE SOURCE CIRCUITS SHALL BE GROUNDED IN ACCORDANCE TO [NEC
690.42].
6. THE GROUNDING CONNECTION TO A MODULE SHALL BE ARRANGED SUCH THAT
THE REMOVAL OF A MODULE DOES NOT INTERRUPT A GROUNDED CONDUCTOR
TO ANOTHER MODULE.
7. EACH MODULE WILL BE GROUNDED USING THE SUPPLIED CONNECTIONS POINTS
IDENTIFIED IN THE MANUFACTURER'S INSTALLATION INSTRUCTIONS.
8. ENCLOSURES SHALL BE PROPERLY PREPARED WITH REMOVAL OF PAINT/FINISH
AS APPROPRIATE WHEN GROUNDING EQUIPMENT WITH TERMINATION
GROUNDING LUGS.
9. GROUNDING SYSTEM COMPONENTS SHALL BE LISTED FOR THEIR PURPOSE, AND
GROUNDING DEVISES EXPOSED TO THE ELEMENTS SHALL BE RATED FOR DIRECT BURIAL.
10. GROUNDING AND BONDING CONDUCTORS SHALL BE COPPER, SOLID OR
STRANDED, AND BARE WHEN EXPOSED.
11. EQUIPMENT GROUNDING CONDUCTORS SHALL BE SIZE ACCORDING TO [NEC
690.451 AND BEA MINIMUM OF #10AWG WHEN NOT EXPOSED TO DAMAGE (#6AWG
SHALL BE USED WHEN EXPOSED TO DAMAGE).
12. GROUNDING AND BONDING CONDUCTORS, IF INSULATED, SHALL BE COLOR
CODED GREEN (OR MARKED GREEN IF #4 AWG OR LARGER)
13. ALL CONDUIT BETWEEN THE UTILITY AC DISCONNECT AND THE POINT OF
CONNECTION SHALL HAVE GROUNDED BUSHINGS AT BOTH ENDS.
14. SYSTEM GEC SIZED ACCORDING TO [NEC 690.47], [NEC TABLE 250.661, DC
SYSTEM GEC SIZED ACCORDING TO [NEC 250.1661, MINIMUM #8AWG WHEN
INSULATED, #6AWG WHEN EXPOSED TO DAMAGE.
15. EXPOSED NON-CURRENT CARRYING METAL PARTS OF MODULE FRAMES,
EQUIPMENTS, AND CONDUCTOR ENCLOSURES SHALL BE GROUNDED IN
ACCORDANCE WITH 250.134 OR 250.136(A) REGARDLESS OF VOLTAGE.
WIRING & CONDUIT NOTES
1. ALL CONDUIT SIZES AND TYPES, SHALL BE LISTED FOR ITS PURPOSE AND
APPROVED FOR THE SITE APPLICATIONS
2. BOLTED CONNECTION REQUIRED IN DC DISCONNECTS ON THE WHITE GROUNDED
CONDUCTOR (USE POLARIS BLOCK OR NEUTRAL BAR)
3. ANY CONNECTION ABOVE LIVE PARTS MUST BE WATERTIGHT. REDUCING WASHERS
DISALLOWED ABOVE LIVE PARTS, MEYERS HUBS RECOMMENDED
4. UV RESISTANT CABLE TIES(NOT ZIP TIES) USED FOR PERMANENT WIRE MANAGEMENT
OFF THE ROOF SURFACE IN ACCORDANCE WITH NEC 110.2,110.3(A -B). 300.4
5. SOLADECK JUNCTION BOXES MOUNTED FLUSH W/ROOF SURFACE TO BE USED FOR
WIRE MANAGEMENT AND AS FLASHED ROOF PENETRATIONS FOR INTERIOR CONDUIT
RUNS.
6. ALL PV CABLES AND HOMERUN WIRES BE TYPE USE -2, AND SINGLE -CONDUCTOR
CABLE LISTED AND IDENTIFIED AS PV WIRE, TYPE TC -ER, OR EQUIVALENT; ROUTED TO
SOURCE CIRCUIT COMBINER BOXES AS REQUIRED
T ALL CONDUCTORS AND OCPD SIZES AND TYPES SPECIFIED ACCORDING TO [NEC
CONDUCTOR SIZE CALCULATIONS
MICROINVERTER TO
MAX. SHORT CIRCUIT CURRRENT (ISC) =
14.0 A AC
JUNCTION BOX (1)
MAX. CURRENT (ISC X1.25) =
17.5 AAC
CONDUCTOR (TC -ER, COPPER (90°C)) =
12 AWG
CONDUCTOR RATING=
30 A
AMB. TEMP. AMP. CORRECTION =
0.96
ADJUSTED AMP. =
28.8 >
17.5
JUNCTION BOX TO
MAX. SHORT CIRCUIT CURRRENT (ISC) =
14.0 A AC
JUNCTION BOX (2)
MAX. CURRENT (ISC X1.25) =
17.5 A AC
CONDUCTOR (THWN-2, COPPER (75°C TERM.)) =
10 AWG
CONDUCTOR RATING =
35 A
CONDUIT FILL DERATE =
1
AMB. TEMP. AMP. CORRECTION =
0.96
ADJUSTED AMP. =
33.6 >
17.5
JUNCTION BOX TO
MAX. SHORT CIRCUIT CURRRENT (ISC) =
14.0 A AC
COMBINER BOX (3)
MAX. CURRENT (ISC X1.25) =
17.5 A AC
CONDUCTOR (THWN-2, COPPER (75°C TERM.)) =
10 AWG
CONDUCTOR RATING =
35 A
CONDUIT FILL DERATE =
1
AMB. TEMP. AMP. CORRECTION =
0.96
ADJ USTE D AMP. =
33.6 >
17.5
COMBINER BOX TO
INVERTER RATED AMPS =
14.0 A AC
MAIN PV OCPD (15)
MAX. CURRENT (RATED AMPS X1.25) =
17.5 A AC
CONDUCTOR (THWN-2, COPPER (75°C TERM.)) =
10 AWG
CONDUCTOR RATING =
3S A
CONDUIT FILL DERATE =
1
AMB. TEMP. AMP. CORRECTION =
0.96
ADJUSTED AMP. =
33.6 >
17.5
690.8] FOR MULTIPLE CONDUCTORS
8. ALL PV DC CONDUCTORS IN CONDUIT EXPOSED TO SUNLIGHT SHALL BE INSTALLED
AT LEAST 7/8" ABOVE THE ROOF SURFACE AND DERATED ACCORDING TO [NEC TABLE
310.15 (13)(2)(a), NEC TABLE 310.15(13)(3)(a),& NEC 310.15(B)(3)(c)].
9. EXPOSED ROOF PV DC CONDUCTORS SHALL BE USE -2, 90°C RATED, WET AND UV
RESISTANT, AND UL LISTED RATED FOR 600V, UV RATED SPIRAL WRAP SHALL BE
USED TO PROTECT WIRE FROM SHARP EDGES
10. PHASE AND NEUTRAL CONDUCTORS SHALL BE DUAL RATED THHN/THWN-2
INSULATED, 90°C RATED, WET AND UV RESISTANT, RATED FOR 600V
11. 4 -WIRE DELTA CONNECTED SYSTEMS HAVE THE PHASE WITH THE HIGHER
VOLTAGE TO GROUND MARKED ORANGE OR IDENTIFIED BY OTHER EFFECTIVE MEANS.
12. ALL SOURCE CIRCUITS SHALL HAVE INDIVIDUAL SOURCE CIRCUIT PROTECTION
13. VOLTAGE DROP LIMITED TO 2% FOR DC CIRCUITS AND 3% FOR AC CIRCUITS
14. NEGATIVE GROUNDED SYSTEMS DC CONDUCTORS SHALL BE COLOR CODED AS
FOLLOWS: DC POSITIVE- RED (OR MARKED RED), DC NEGATIVE- GREY (OR MARKED GREY)
15. POSITIVE GROUNDED SYSTEMS DC CONDUCTORS COLOR CODED:
DC POSITIVE- GREY (OR MARKED GREY), DC NEGATIVE- BLACK (OR MARKED BLACK)
16. AC CONDUCTORS >4AWG COLOR CODED OR MARKED:
PHASE A OR L1- BLACK, PHASE B OR L2- RED, PHASE C OR 1_3- BLUE, NEUTRAL-
WHITE/GRAY
USE -2 IS NOT INDOOR RATED BUT PV CABLE IS RATED THWN/THWN-2 AND MAY
BE USED INSIDE
" USE -2 IS AVAILABLE AS UV WHITE
17, RIGID CONDUIT, IF INSTALLED, (AND/OR NIPPLES) MUST HAVE A PULL BUSHING TO
PROTECT WIRES.
18, IF CONDUIT DETERMINED TO BE RAN THROUGH ATTIC IN FIELD THEN CONDUIT WILL
BE EITHER EMT, FMC, OR MC CABLE IF DC CURRENT COMPLYING WITH NEC 690.31, NEC
250.118(10). DISCONNECTING MEANS SHALL COMPLY WITH 690.13 AND 690.15
19. CONDUIT RAN THROUGH ATTIC WILL BE AT LEAST 18" BELOW ROOF SURFACE
COMPLYING WITH NEC 230.6(4) AND SECURED NO GREATER THAN & APART PER NEC
330.30(B).
4 .
RAVENBLUE
1403 N RESEARCH WAY, BUILDING J
OREM, UT 84097
800-377-4480
WWW.BLUERAVENSOLAR.COM
CONFIDENTIAL -THE INFORMATION
HEREIN CONTAINED SHALL NOT BE
USED FOR THE BENEFIT OF
ANYONE EXCEPT
BLUERAVENSOLAR NOR SHALL IT
BE DISCLOSED IN WHOLE OR IN
PART TO OTHERS OUTSIDE
RECIPIENTS ORGANIZATION,
EXCEPT IN CONNEC TION WITH THE
SALE AND USE OF THE RESPECTIVE
EQUIPMENT, WITHOUT THE
WRITTEN PERMISSION OF
BLUERAVENSOLAR LLC.
Z
O
O
LL
Z
W
r'
�CERTIFIED�
PV INSTALLATION
PROFESSIONAL
Scott Gurney
# PV -011719-015866
CONTRACTOR:
BRS FIELD OPS
385.498.6700
N
O
GO
O
(U
O
U
0
Y
N
4
W
N
U)
2
W
I-
U)
W
0
DIN ENG" RING
AT jrky
, 2020
ROJECT NUMBER
72118210
SHEET NAME
ELEC. CALCS.
PAGE NUMBER REVISION
PV6 0
ELECTRIC SHOCK HAZARD
TERMINALS ON THE LINE AND
LOAD SIDES MAY BE ENERGIZED
._w_ IN THE OPEN POSITION -
!
PHOTOVOLTAIC POI.WR S,!
MAXIMUM VOLTAGE VDC
MAX CIRCUIT CURRENT AMPS
RATED AC OUTPUT CURRENT A
NOMINAL OPERATING AC VOLTAGE V
,,WARNING
DUAL POWER SUPPLY
SOURCES: UTILITY GRID AND
PV SOLAR ELECTRIC SYSTEM
INVERTER OUTPUT CONNECTION
DO NOT RELOCATE
THIS OVERCURRENT
DEVICE
THIS EQUIPMENT FED BY MULTIPLE
SOURCES. TOTAL RATING OF ALL
OVERCURRENT DEVICES, EXCLUDING
MAIN SUPPLY OVERCURRENT
DEVICE. SHALL NOT EXCEED
AMPACITY OF BUSBAR.
PHOTOVOLTAIC
SYSTEM CONNECTED
PV AC DISCONNECT
LABEL 1
FOR PV DISCONNECTING MEANS WHERE ALL
TERMINALS OF THE DISCONNECTING MEANS
MAY BE ENERGIZED IN THE OPEN POSITION.
[NEC 690.13(B).. NEC 705.221
LABEL 2
AT EACH DC DISCONNECTING MEANS,
INCLUDING THE DC DISCONNECT AT THE
INVERTER.
[NEC 690.53, NEC 690.13(B)]
LABEL 3
AT POINT OF INTERCONNECTION, MARKED AT
AC DISCONNECTING MEANS
[NEC 690.54, NEC 690.13 (B)]
LABEL 4
AT POINT OF INTERCONNECTION FOR
EQUIPMENT CONTAINING OVERCURRENT
DEVICES IN CIRCUTS SUPPLYING POWER TO A
BUSBAR OR CONDUCTOR SUPPLIED FORM
MULTIPLE SOURCES, EACH SERVICE
EQUIPMENT AND ALL ELECTRIC POWER
PRODUCTION SOURCE LOCATIONS. [NEC
705.12(B)(3)]
LABEL 5
PLACED ADJACENT TO THE BACK -FED BREAKER
FROM THE INVERTER IF TIE IN CONSISTS OF
LOAD SIDE CONNECTION TO BUSBAR.
[NEC 705.12(B)(2)(3)(b)]
LABEL 6
(ONLY IF 3 OR MORE SUPPLY SOURCES TO
A BUSBAR)
SIGN LOCATED AT LOAD CENTER IF IT
CONTAINS 3 OR MORE POWER SOURCES.
[NEC 705.12(B)(2)(3)(C)]
LABEL 10
SIGN LOCATED AT RAPID SHUT DOWN
DISCONNECT SWITCH [NEC 690.56(C)(3)].
LABEL 12
PLACARD TO BE PLACED AT THE MAIN
BILLING METER PER XCEL ENERGY.
LABEL 13
PLACARD TO BE PLACED AT AC
DISCONNECT PER XCEL ENERGY.
SOLAR PV SYSTEM EQUIPPED
WITH RAPID SHUTDOWN
TURN RAPID SHUTDOWN
SWITCH TO THE
'OFF' POSITION TO KW SICIRC
SHUT DOWN PV SYSTEM wwnas
AND REDUCE
SHOCKHA7ARD
_,„ 'sN T-IEARRAY
LABEL 7
AT DIRECT-CURRENT EXPOSED RACEWAYS, CABLE TRAYS. COVERS AND ENCLOSURES OF
JUNCTION BOXES, AND OTHER WIRING METHODS: SPACED AT MAXIMUM 1OFT SECTION OR
WHERE SEPARATED BY ENCLOSURES, WALLS, PARTITIONS, CEILINGS, OR FLOORS.
[NEC 690.31(G)(3&4)]
LABEL 8
FOR PV SYSTEMS THAT SHUT DOWN THE ARRAY
AND CONDUCTORS LEAVING THE ARRAY:
SIGN TO BE LOCATED ON OR NO MORE THAN 3
FT AWAY FROM SERVICE DISCONNECTING
MEANS TO WHICH THE PV SYSTEMS ARE
CONNECTED AND SHALL INDICATE THE
LOCATION OF ALL IDENTIFIED RAPID SHUTDOWN
SWITCHES IF NOT AT THE SAME LOCATION.
[NEC 690.56(C)(1)(A)]
& WARNING
LABEL 9 POWER TO THIS BUILDING IS ALSO
FOR PV SYSTEMS THAT ONLY SHUT DOWN
CONDUCTORS LEAVING THE ARRAY: SUPPLIED FROM MAIN DlsTweuTTON
! • - UTILITY DISCONNECT LOCATED
TURN RAM SHUTDOWN SWITCH SIGN TO BE LOCATED ON OR NO MORE THAN 3
TOTHE'Q FPOSmON ® FT AWAY FROM SERVICE DISCONNECTING
TO SHUT DOWN CONDUCTORS ------ MEANS TO WHICH THE PV SYSTEMS ARE
OUTSIDE THE ARRAY CONNECTED AND SHALL INDICATE THE
CONDUCTORS WITHIN LOCATION OF ALL IDENTIFIED RAPID SHUTDOWN
THEARRAYREMAIN
ENERGIZED IN SUNLIGHT SWITCHES IF NOT AT THE SAME LOCATION.
[NEC 690.56(C)(1)(B)] & WARNING
�..,.... _,....... ._.._._,_,.,. s._..,._,.u,...-, ,.,-..-.M..,.—...,I LABEL 11 POWER TO THIS BUILDING IS ALSO SUPPLIED
t FROM ROOF MOUNTED SOLARARRAY. SOLAR
"RESPRESEW I SIGN LOCATED AT AC COMBINER BOX FOR
_.. _,..j ALL MICRO-INVERTER/AC MODULE ARRAY RAPID SHUTDOWN DISCONNECT IS
� � UT _.. INSTALLS (IF APPLICABLE). LOCATED OUTSIDE NEXT TO UTILITY METER.
RAPID SHUTDOWN TEST
NOT REQUIRED
LABELING DIAGRAM FOR MICRO INV..
MAIN SERVICE PANEL
LABELING NOTES:
1, LABELS CALLED OUT ACCORDING TO ALL COMMON CONFIGURATIONS. ELECTRICIAN TO
DETERMINE EXACT REQUIREMENTS IN THE FIELD PER CURRENT NEC AND LOCAL CODES AND
MAKE APPROPRIATE ADJUSTMENTS.
2, LABELING REQUIREMENTS BASED ON THE 2017 NATIONAL ELECTRIC CODE, OSHA STANDARD
19010.145, ANSI Z535.
3 MATERIAL BASED ON THE REQUIREMENTS OF THE AUTHORITY HAVING JURISDICTION.
4. LABELS TO BE OF SUFFICIENT DURABILITY TO WITHSTAND THE ENVIRONMENT INVOLVED [NEC
110.211
5. LABELS TO BE A MINIMUM LETTER HEIGHT OF 3/8", WHITE ON RED BACKGROUND, REFLECTIVE,
AND PERMANENTLY AFFIXED [IFC 605.11.1.11
LABEL 16
PERMANENT DIRECTORY TO BE LOCATED AT
SOLAR ARRAY RAPID SHUTDOWN SWITCH
DENOTING THE LOCATION OF THE SERVICE
EQUIPMENT LOCATION IF SOLAR ARRAY RAPID
SHUT DOWN DISCONNECT SWITCH IS NOT
GROUPED AND WITHIN LINE OF SITE OF MAIN
SERVICE DISCONNECTING MEANS.
[NEC 705.10]
LABEL 17
PERMANENT DIRECTORY TO BE LOCATED AT MAIN
SERVICE EQUIPMENT DENOTING THE LOCATION
OF THE PV RAPID SHUTDOWN SYSTEM
DISCONNECTING MEANS IF SOLAR ARRAY RAPID
SHUT DOWN DISCONNECT SWITCH IS NOT
GROUPED AND WITHIN LINE OF SITE OF MAIN
SERVICE DISCONNECTING MEANS. [NEC 705.10,
NEC 690.56(C)(1)]
BLUE RAVEN
1403 N RESEARCH WAY, BUILDING J
OREM, UT 84097
800-377-4480
W W W.BLU ERAVENSOLAR.COM
CONFIDENTIAL - THE INFORMATION
HEREIN CONTAINED SHALL NOT BE
USED FOR THE BENEFIT OF
ANYONE EXCEPT
BLUERAVENSOLAR NOR SHALL IT
BE DISCLOSED IN WHOLE OR IN
PART TO OTHERS OUTSIDE
RECIPIENTS ORGANIZATION,
EXCEPT IN CONNEC TION WITH THE
SALE AND USE OF THE RESPECTIVE
EQUIPMENT, WITHOUT THE
WRITTEN PERMISSION OF
BLUERAVENSOLAR LLC.
CERTIFIED
PV INSTALLATION
PROFESSIONAL
Scott Gurney
# PV -011719-015866
CONTRACTOR:
BRS FIELD OPS
385.498.6700
EXISTING SUB PANEL PV COMBINER
1O O8 (IF WHERE POINT OF SUBPANEL -
INTERCONNECTION AC DISCONNECT IF USED TO COMBINE AC JUNCTION BOX
12 13 IS MADE) (IF REQ /INSTALLED) PV OUTPUT CIRCUITS OR AC COMBINER BOX
°°00 COO U T_O &O4 T D
° O ° IF BREAKER USED13 CV
15 OR 17 00
OR PLACARD O &O 16 O _ O C\I
IF BREAKER USE Z 0
O
(ONLY IF PV O 0 L
O p LLI
INTERCONNECTION [— = p N
CONSISTS OF LOAD 11 Q L (�
SIDE BREAKER) CV
LABELING DIAGRAM FOR STRING INV. / DC OPTIMIZER INV w
MAIN SERVICE PANEL O M _ U)
EXISTING SUB PANEL PV COMBINER INVERTER (S) — -O fn
O13 (IF WHERE POINT OF SUBPANEL - LL1 CV U)
OINTERCONNECTION AC DISCONNECT IF USED TO COMBINE
12 IS MADE) (IF REQ / INSTALLED) PV OUTPUT CIRCUITS U) m CO > Q
O & O4
° D IF BREAKER USED O O O O o IN BY
D ° D s QR g IN EI' %EERING
O3 &O4 16 13 O4
15 OR 17 F BREAKER USE ac e
JUNCTION BOX DAT
ORP CARD O oc OR COMBINER BOX
55 O i UI VISI ,
(ONLY IF PV (ONLY IF PVO 10 O O PROJECT NUMBER
INTERCONNECTIONINTERCONNECTION 72118210
CONSISTS OF LOA CONSISTS OF LOA 11 �� O O7
SIDE BREAKER) SIDE BREAKER)
INTEGRATED DC DISCONNECT SHEET NAME
LABELS
*ELECTRICAL DIAGRAMS SHOWN ABOVE IS FOR LABELING PURPOSES ONLY. NOT AN ACTUAL REPRESENATION OF EQUIPMENT AND CONNECTIONS TO BE INSTALLED, LABEL LOCATIONS
PRESENTED MAY VERY DEPENDING ON TYPE OF INTERCONNECTION METHOD AND LOCATION PRESENTED ON PV5 OF 3 LINE DIAGRAM. PV5 LINE DIAGRAM TO REFLECT ACTUAL
REPRESENTATION OF PROPOSED SCOPE OF WORK. PAGE NUMBER REVISION
PV8 0
LABEL 15
WARNING
PERMANENT DIRECTORY TO BE LOCATED AT
MAIN SERVICE EQUIPMENT LOCATION IF ALL
MAIN DISTRIBUTION UTILlTYDISCONNECT(S)
ELECTRICAL POWER SOURCE DISCONNECTING
POWER TO THIS BUILDING IS ALSO SUPPLIED
MEANS (SOLAR ARRAY RAPID SHUTDOWN
FROM A ROOF MOUNTED SOLAR ARRAY WITH
A RAPID SHUTDOWN DISCONNECTING MEANS
SWITCH) ARE GROUPED AND IN LINE OF SITE OF
GROUPED AND LABELED WITHIN LINE OFSITE
MAIN SERVICE DISCONNECTING MEANS.
aND 10 FTaFTHIS LOCATION.
[NEC 690.56(C) & NEC 705.10].
& WARNING
LABEL 9 POWER TO THIS BUILDING IS ALSO
FOR PV SYSTEMS THAT ONLY SHUT DOWN
CONDUCTORS LEAVING THE ARRAY: SUPPLIED FROM MAIN DlsTweuTTON
! • - UTILITY DISCONNECT LOCATED
TURN RAM SHUTDOWN SWITCH SIGN TO BE LOCATED ON OR NO MORE THAN 3
TOTHE'Q FPOSmON ® FT AWAY FROM SERVICE DISCONNECTING
TO SHUT DOWN CONDUCTORS ------ MEANS TO WHICH THE PV SYSTEMS ARE
OUTSIDE THE ARRAY CONNECTED AND SHALL INDICATE THE
CONDUCTORS WITHIN LOCATION OF ALL IDENTIFIED RAPID SHUTDOWN
THEARRAYREMAIN
ENERGIZED IN SUNLIGHT SWITCHES IF NOT AT THE SAME LOCATION.
[NEC 690.56(C)(1)(B)] & WARNING
�..,.... _,....... ._.._._,_,.,. s._..,._,.u,...-, ,.,-..-.M..,.—...,I LABEL 11 POWER TO THIS BUILDING IS ALSO SUPPLIED
t FROM ROOF MOUNTED SOLARARRAY. SOLAR
"RESPRESEW I SIGN LOCATED AT AC COMBINER BOX FOR
_.. _,..j ALL MICRO-INVERTER/AC MODULE ARRAY RAPID SHUTDOWN DISCONNECT IS
� � UT _.. INSTALLS (IF APPLICABLE). LOCATED OUTSIDE NEXT TO UTILITY METER.
RAPID SHUTDOWN TEST
NOT REQUIRED
LABELING DIAGRAM FOR MICRO INV..
MAIN SERVICE PANEL
LABELING NOTES:
1, LABELS CALLED OUT ACCORDING TO ALL COMMON CONFIGURATIONS. ELECTRICIAN TO
DETERMINE EXACT REQUIREMENTS IN THE FIELD PER CURRENT NEC AND LOCAL CODES AND
MAKE APPROPRIATE ADJUSTMENTS.
2, LABELING REQUIREMENTS BASED ON THE 2017 NATIONAL ELECTRIC CODE, OSHA STANDARD
19010.145, ANSI Z535.
3 MATERIAL BASED ON THE REQUIREMENTS OF THE AUTHORITY HAVING JURISDICTION.
4. LABELS TO BE OF SUFFICIENT DURABILITY TO WITHSTAND THE ENVIRONMENT INVOLVED [NEC
110.211
5. LABELS TO BE A MINIMUM LETTER HEIGHT OF 3/8", WHITE ON RED BACKGROUND, REFLECTIVE,
AND PERMANENTLY AFFIXED [IFC 605.11.1.11
LABEL 16
PERMANENT DIRECTORY TO BE LOCATED AT
SOLAR ARRAY RAPID SHUTDOWN SWITCH
DENOTING THE LOCATION OF THE SERVICE
EQUIPMENT LOCATION IF SOLAR ARRAY RAPID
SHUT DOWN DISCONNECT SWITCH IS NOT
GROUPED AND WITHIN LINE OF SITE OF MAIN
SERVICE DISCONNECTING MEANS.
[NEC 705.10]
LABEL 17
PERMANENT DIRECTORY TO BE LOCATED AT MAIN
SERVICE EQUIPMENT DENOTING THE LOCATION
OF THE PV RAPID SHUTDOWN SYSTEM
DISCONNECTING MEANS IF SOLAR ARRAY RAPID
SHUT DOWN DISCONNECT SWITCH IS NOT
GROUPED AND WITHIN LINE OF SITE OF MAIN
SERVICE DISCONNECTING MEANS. [NEC 705.10,
NEC 690.56(C)(1)]
BLUE RAVEN
1403 N RESEARCH WAY, BUILDING J
OREM, UT 84097
800-377-4480
W W W.BLU ERAVENSOLAR.COM
CONFIDENTIAL - THE INFORMATION
HEREIN CONTAINED SHALL NOT BE
USED FOR THE BENEFIT OF
ANYONE EXCEPT
BLUERAVENSOLAR NOR SHALL IT
BE DISCLOSED IN WHOLE OR IN
PART TO OTHERS OUTSIDE
RECIPIENTS ORGANIZATION,
EXCEPT IN CONNEC TION WITH THE
SALE AND USE OF THE RESPECTIVE
EQUIPMENT, WITHOUT THE
WRITTEN PERMISSION OF
BLUERAVENSOLAR LLC.
CERTIFIED
PV INSTALLATION
PROFESSIONAL
Scott Gurney
# PV -011719-015866
CONTRACTOR:
BRS FIELD OPS
385.498.6700
EXISTING SUB PANEL PV COMBINER
1O O8 (IF WHERE POINT OF SUBPANEL -
INTERCONNECTION AC DISCONNECT IF USED TO COMBINE AC JUNCTION BOX
12 13 IS MADE) (IF REQ /INSTALLED) PV OUTPUT CIRCUITS OR AC COMBINER BOX
°°00 COO U T_O &O4 T D
° O ° IF BREAKER USED13 CV
15 OR 17 00
OR PLACARD O &O 16 O _ O C\I
IF BREAKER USE Z 0
O
(ONLY IF PV O 0 L
O p LLI
INTERCONNECTION [— = p N
CONSISTS OF LOAD 11 Q L (�
SIDE BREAKER) CV
LABELING DIAGRAM FOR STRING INV. / DC OPTIMIZER INV w
MAIN SERVICE PANEL O M _ U)
EXISTING SUB PANEL PV COMBINER INVERTER (S) — -O fn
O13 (IF WHERE POINT OF SUBPANEL - LL1 CV U)
OINTERCONNECTION AC DISCONNECT IF USED TO COMBINE
12 IS MADE) (IF REQ / INSTALLED) PV OUTPUT CIRCUITS U) m CO > Q
O & O4
° D IF BREAKER USED O O O O o IN BY
D ° D s QR g IN EI' %EERING
O3 &O4 16 13 O4
15 OR 17 F BREAKER USE ac e
JUNCTION BOX DAT
ORP CARD O oc OR COMBINER BOX
55 O i UI VISI ,
(ONLY IF PV (ONLY IF PVO 10 O O PROJECT NUMBER
INTERCONNECTIONINTERCONNECTION 72118210
CONSISTS OF LOA CONSISTS OF LOA 11 �� O O7
SIDE BREAKER) SIDE BREAKER)
INTEGRATED DC DISCONNECT SHEET NAME
LABELS
*ELECTRICAL DIAGRAMS SHOWN ABOVE IS FOR LABELING PURPOSES ONLY. NOT AN ACTUAL REPRESENATION OF EQUIPMENT AND CONNECTIONS TO BE INSTALLED, LABEL LOCATIONS
PRESENTED MAY VERY DEPENDING ON TYPE OF INTERCONNECTION METHOD AND LOCATION PRESENTED ON PV5 OF 3 LINE DIAGRAM. PV5 LINE DIAGRAM TO REFLECT ACTUAL
REPRESENTATION OF PROPOSED SCOPE OF WORK. PAGE NUMBER REVISION
PV8 0
Lnpila�e �t;�:1�,itl�Ferter
Enphase
IQ 7 and IQ 7
Microinverters
TO learn more about Enphase offerings, visit enphase,corn
r.e r gh-po,. erect smart grid -ready
ar-,d E,w,3' -s Ifs 7- ,t
dra is-ical } s`mplity t -e nstallation process ,�,h* e
achie,.J-,g -he ^ighes-. system efficiency.
Part of t -e Enp ase IQ System, the !Q 1 o^d
0 x- Microinverters integrate with the Enprase
,Q Envoy-, Enphase IO Batter,- a-c.he E^phase
Enlighte-" mo7`toring and a! -al 5'5 so'tievar_.
IQ Sere= !`,,tcrclr;verters ex;e.^d the reliahiiit
standards set -:ort^ by pr vio,:s generations and
un� ergo o-,,er a •�-r`Ilia hours of power -on testing,
erabl=ng Enp^ase to provide air ndustrzj- ending
,.varranty of up to 25 years.
Easy to Install
• L g-tv,- 3:-t snd sirrtple
Faster it atal a-. c- _, tF r -:proved, ighter two -+nine cabl`_ng
Bu 1t-ir rabid sF_;:covor, compliant INEC 2014 & 2017
Productive and Reliable
Opt r-_zsd for h-gh powered 6C-ce l and 72-ce 1" modules
• ttia"ar~= than a r�> 11=c� Fours �f testir�
C ass 11 dOL le -insulated enclosure
UL I sted
Complses advanced grid support, voltage and
fregt er g,. ride -through re(juiremrems,
Pc tely Updates to respond to changing
grid requirements
Corficyarable $Car varjirg grid profiles
Mee*s GA Rule 21 (UL -1741
�7F� iG 7b }.!ia-o � �cufrerJl� supw�r•. "�.eiE ;°�aou4es
ENPI LASE.
Enphase IQ 7 and IQ 7+ Microinverters
INPUT DATA (DC)
IQ7-60-2-US / IQ7-60-B-US
IQ7PLUS-72-2-US / IQ7PLUS-72-B-US
�.w a_._�.M- ._.....M....-
Commonly used module pairings'
235 W - 350 W +
235 W - 440 W +
Module compatibility
60 -cell PV modules only
60 -cell and 72 -cell PV modules
Maximum input DC voltage
48 V
60V
Peak power tracking voltage
27 V -37 V
27 V- 45 V
Operating range
16V -48V
16V -60V
Min/Max start voltage
22 V 148 V
22 V/ 60 V
Max DC short circuit current (module Isc)
15 A
15A
Overvoltage class DC port
11
II
DC port backfeed current
0 A
0 A
PV array configuration
1 x 1 ungrounded array. No additional DC side protection required,
AC side protection requires max 20A per branch circuit
inverter
1114W
BLUE RAVEN
1403 N RESEARCH WAY, BUILDING J
OREM, UT 84097
800-377-4480
WWW. BLUERAVENSOLAR.COM
CONFIDENTIAL - THE INFORMATION
HEREIN CONTAINED SHALL NOT BE
USED FOR THE BENEFIT OF
ANYONE EXCEPT BLUE RAVEN
SOLAR NOR SHALL IT BE
DISCLOSED IN WHOLE OR IN PART
TO OTHERS OUTSIDE RECIPIENTS
ORGANIZATION, EXCEPT IN
CONNECTION WITH THE SALE AND
USE OF THE RESPECTIVE
EQUIPMENT, WITHOUT THE
WRITTEN PERMISSION OF BLUE
RAVEN SOLAR LLC.
Peak output power
250 VA 295 VA
r
Maximum continuous output power
240 VA 290 VA
Nominal {L -L) voltage/range'
240 V / 208V/ 240V/ 208V/
211-264V 183-229V 211-264V 183-229V
�CERTIFI=ED
Maximum continuous output current
1.0 A (240 V) 1.15 A (208 V) 1.21 A (240 V) 1.39 A (208 V)
Nominal frequency
60 Hz 60 Hz
PV INSTALLATION
Extended frequency range
47 - 68 Hz 47 - 68 Hz
PROFESSIONAL
AC short circuit fault current over 3 cycles
5.8 Arms 5.8 Arms
Scott Gurney
Maximum units per 20 A (L -L) branch circuit'
16 (240 VAC) 13 (208 VAC) 13 (240 VAC) 11 (208 VAC)
# PV -011719-015866
Overvoltage class AC port
III III
CONTRACTOR:
AC port backfeed current
0 A 0 A
B RS FIELD OPS
Power factor setting
1.0 1.0
Power factor (adjustable)
0.7 leading... OJ lagging 0.7 leading 0.7 lagging
385.498.6700
EFFICIENCY
@240 V @208 V @240 V @208 V
Peak CEC efficiency
97.6 % 97.6 97.5 `�s 97.3 o
CEC weighted efficiency
97.0'x, 97.0 %� 97.0 `_ 97.0' -
MECHANICAL DATA
Ambient temperature range
-40°C to +65°C _. P
Relative humidity range
4`% to 100`,,< (condensing)
Connector type (IQ7-60-2-US & IQ7PLUS-72-2-US) MC4 (or Amphenol H4 UTX with additional Q -DCC -5 adapter)
Connector type (IQ7-60-B-US & IQ71PLUS-72-B-US) Friends PV2 (MC4 intermateable).
Adaptors for modules with MC4 or UTX connectors:
PV2 to MC4: order ECA -S20 -S22
PV2 to UTX: order ECA -S20 -S25
Dimensions (WxHxD)
212 mm x 175 mm x 30.2 mm (without bracket)
Weight
1.08 kg (2.38 lbs)
Cooling
Natural convection - No fans
Approved for wet locations
Yes
Pollution degree
PD3
Enclosure
Class II double -insulated, corrosion resistant polymeric enclosure
Environmental category / UV exposure rating
NEMA Type 6 / outdoor
FEATURES
Communication
Power Line Communication (PLC)
Monitoring
Enlighten Manager and MyEnlighten monitoring options.
Both options require installation of an Enphase IQ Envoy.
Disconnecting means
The AC and DC connectors have been evaluated and approved by UL for use as the load -break
City of
disconnect required by NEC 690.
Compliance
CA Rule 21 (UL 1741 -SA)
heat Ridge
UL 62109-1, UL1741/IEEE1547, FCC Part 15 Class B, ICES -0003 Class B,
CAN/CSA-C22.2 NO. 107.1-01
This product is UL Listed as PV Rapid Shut Down Equipment and conforms with NEC -2014 and
ild
NEC -2017 section 690.12 and C22.1-2015 Rule 64-218 Rapid Shutdown of PV Systems, for AC
•
and DC conductors, when installed according manufacturer's instructions
t. No enforced =IC/AC ratio. See the c.ompaiib:I ly calculator at Wl sit haae eomfen-usisupporiimodiile-Comt)alibil'l_y,
2. Normal voltage range can be extended beyond nor :nal '.f reGu'red by the utility.
,., -ir t.ts r,�ay vary. Refer to local iequ=iemenisio define the number of rr'croinverters per branch in yow area.
SHEET NAME
To learn more about Enphase offerings, visitenphase.com ENPHASE. SPEC SHEET
20PAGE NUMBER REVISION
��=R
Enphase Networking
IQ Combiner
U�
LISTED
To learn more about Enphase offerings, visit enphase.com
The Enphase lQ Combiner 3°' with Enphase
IQ Envoy-' conso'idates interconnection
equ pment Into a sng'.e enclosure and
stream nes PV and storage insta at ons by
prov dng a consistent, pre°',fired so ut'on 'or
residenfa app cations. It oTfers up to 'our
2-po e'nput c rcuits and Eaton BR ser'es
busbar assemb'y.
Smart
Includes IQ Envoy for communication
and control
Flexible networking supports WI-Fi,
Ethernet, or cellular
Optional AC receptacle available for PLC
bridge
Provides production metering and optional
consumption monitoring
Simple
Reduced size from previous combiner
Centered mounting brackets supportsingle
stud mounting
Supports back and side conduit entry
Up to four 2 -pole branch circuits for 240 VAC
plug-in breakers (not included)
80 A total PV or storage branch circuits
Reliable
Durable NRTL-certified NEMA type
3R enclosure
Five-year warranty
UL listed
ENPHASE,
00
*4%W
BLUE RAVEN
Enphase IQ Combiner 3
1403 N RESEARCH WAY. BUILDING J
OREM. UT 84097
MODEL NUMBER
IQ Combiner 3 X -IQ -AMI -240-3
IQ Combiner 3 with Enphase IQ Envoy" printed circuit board for integrated revenue grade PV
800-377-4480
production metering (ANSI C12.20 +/-0.5 i) and optional* consumption monitoring (+/-2,5%).
WWW BLUERAVENSOLAR.COM
ACCESSORIES and REPLACEMENT PARTS (not included, order separately)
x
CONFIDENTIAL - THE INFORMATION
Enphase Mobile Connect'"
HEREIN CONTAINED SHALL NOT BE
CELLMODEM-03 (4G / 12 -year data plan)
Plug and play industrial grade cellular modem with data plan for systems up to 60
USED FOR THE BENEFIT OF
CELLMODEM-01 (3G / 5 -year data plan)
microinverters. (Available in the US, Canada, Mexico, Puerto Rico, and the US Virgin Islands,
ANYONE EXCEPT BLUE RAVEN
CELLMODEM-M1 (4G based LTE -M 15-yeardata plan) where there is adequate cellular service in the installation area.)
SOLAR NOR SHALL IT BE
Consumption Monitoring* CT
DISCLOSED IN WHOLE OR IN PART
CT -200 -SPLIT
Split core current transformers enable whole home consumption metering (+/- 2.5%.).
TO OTHERS OUTSIDE RECIPIENTS
Circuit Breakers
Supports Eaton BR210, BR215, BR220, BR230, BR240, BR250, and BR260 circuit breakers.
ORGANIZATION, EXCEPT IN
BRK-10A-2-240
Circuit breaker, 2 pole, 10A, Eaton BR210
CONNECTION WITH THE SALE AND
BRK-15A-2-240
Circuit breaker, 2 pole, 15A, Eaton BR215
USE THE RESPECTIVE
BRK-20A-2P-240
Circuit breaker, 2 pole, 20A, Eaton BR220
EQUIPMENT, WITHOUT THE
WRITTEN PERMISSION OF BLUE
EPLC-01
Power line carrier (communication bridge pair), quantity 2
RAVEN SOLAR LLC.
XA-PLUG-120-3
Accessory receptacle for Power Line Carrier in IQ Combiner 3 (required for EPLC-01)
r-
XA-ENV-PCBA-3
Replacement IQ Envoy printed circuit board (PCB) for Combiner 3
{ L 4.,
C 6�I CI C D�
ELECTRICAL SPECIFICATIONSCERTIFIED
Rating
Continuous duty
PV INSTALLATION
System voltage 120/240 VAC, 60 Hz
Eaton BR series busbar rating
125 A
PROFESSIONAL
Scott
Max. continuous current rating (output to grid)
65A
# PV -0117119-015866
Max. fuse/circuit rating (output)
90A
CONTRACTOR:
Branch circuits (solar and/or storage)
Up to four 2 -pole Eaton BR series Distributed Generation (DG) breakers only (not included)
BRS FIELD OPS
Max. continuous current rating (input from PV)
64A
38
385.498.6700
Max. total branch circuit breaker rating (input)
80A of distributed generation / 90A with IQ Envoy breaker included
Production Metering CT
200 A solid core pre-installed and wired to IQ Envoy
MECHANICAL DATA
Dimensions (WxHxD)
49.5 x 37.5 x 16.8 cm (19.5" x 14.75" x 6.63"). Height is 21.06"(53.5 cm with mounting brackets)
Weight
7.5 kg (16.5 Ibs)
Ambient temperature range
-40° C to +46° C (-400 to 115° F)
Cooling
Natural convection, plus heat shield
Enclosure environmenta I rating
Outdoor, N RTL -certified, NEMA type 3R, polycarbonate construction
Wire sizes
20 A to 50 A breaker inputs: 14 to 4 AWG copper conductors
60 A breaker branch input: 4 to 1/0 AWG copper conductors
Main lug combined output: 10 to 2/0 AWG copper conductors
Neutral and ground: 14 to 1/0 copper conductors
Always follow local code requirements for conductor sizing.
Altitude
To 2000 meters (6,560 feet)
INTERNET CONNECTION OPTIONS
Integrated Wi-F!
802.11bigtn
Ethernet
Optional, 802.3, Cat5E (or Cat 6) UTP Ethernet cable (not included)
Cellular
Optional, CELLMODEM-01 (3G) or CELLMODEM-03 (4G) or CELLMODEM-M1 (4G based LTE -M)
(not included)
City of
COMPLIANCE
Compliance, Combiner
UL 1741
CAN/GSA 022.2 No. 107.1
(/ t Ridge
47 CFR, Part 15, Class B, ICES 003
/
Production metering: ANSI C12.20 accuracy class 0.5 (PV production)
i Buil ding Div
Compliance, IQ Envoy UL 60601 VCANCSA 22.2 No 61010-1
* Consumption monitoring is required for Enphase Storage systems.
To learn more about Enphase offerings, visit enphase.com
SHEET NAME
SPEC SHEET
PAGE NUMBERI REVISION
SS 0
°"•��f7��t i11�1'�4
SERAPHIM
ENERGY CRDUP
SEG-6MB-xxxBB SERIES 61NCH 60 CELLS
W
BB.BUCK ..ET tBtA.CK FRAME PRODtIGTS
Electrical Characteristics(STC)
Maximum Power at STC -P„ (W) 295 300 305 310
2 9 5 ^' � � C) W PE RC Open Circuit Voltage -V� (V) 39.5 397 39.9 40.2
Safety Short Circuit Current -Is iA) 956 9.65 9.76 982
Maximum Power Voltage -V„ (V) 31.9 321 32.3 32.6
Maximum Power Current -Ion (A) 9.25 9.35 9.45 8.51
Module Efficiency STC -q,,, f°%) 18.13 18.44 18.75 1905.
Power Tolerance �W; 10,+4.99)
Maximum System Voltage (V) 1000 or 1500{UL)
Resistance to salt mist Resistance to amm orva Product is certified Maximum Senes Fuse Rating (A) 20
corrosion at your request corrosion at your request by UL1703
Fre Performance Type2 or Type1(UL)
Reliability
PID
Anti -PID products using
advanced module
technology
�e
Wald t st company to pass
'Threshes Test" and On-site
Power Measurement
Validation" certificate
(5
Bankable products
Electrical Characteristics(NOCT)
Maximum Power at NOCT-p_(W)
219
223
226
230
Open Circuit Voltage -Vn, (V)
36.5
36.7
36.8
37.1
Short Circuit Current -Iy (A)
7.73
7.82
7.91
796
Maximum Power Voltage -V„v(V)
30.1
30.3
30.4
30.7
Maximum Power Current -1,,,, iA)
728
7.36
7.44
7.50
Performance Temperature Characteristics
Pmax Temperature Coetfiaent -038%r'C
Vac Temperature f:oel5aent -0.28 °N°C
Isc Temperature Coefficient +0.05 %PC
Operating Temperature -40- 85 -C
High efficiency and enhanced Outstanding power output Withstand up to 24001ca Nominal Operating Coll Temperature (NOCT) 4532 "C
module durability capability at low irradiance wind and 5400Pa snow
loads(IEC), long lasting
Packing Configuration
SpeaSeat,ons are subject to change without nctificato SEC, OS -EN -2019V1.1 Copyright 2019 Seraphim
a 70
I
5.1 21 Section A -A
101
All Dimensions in mm
The above drawing is a graphical representation of the product.
IN Curve
a nc
= sap wm
t
i RAVEN to
1403 N RESEARCH WAY, BUILDING J
OREM, UT 84097
800-377-4480
WWW. BLUERAVENSOLAR.COM
CONFIDENTIAL - THE INFORMATION
HEREIN CONTAINED SHALL NOT BE
USED FOR THE BENEFIT OF
ANYONE EXCEPT BLUE RAVEN
SOLAR NOR SHALL IT BE
DISCLOSED IN WHOLE OR IN PART
TO OTHERS OUTSIDE RECIPIENTS
ORGANIZATION, EXCEPT IN
CONNECTION WITH THE SALE AND
USE OF THE RESPECTIVE
EQUIPMENT, WITHOUT THE
WRITTEN PERMISSION OF BLUE
RAVEN SOLAR LLC.
^.
FCERTIFIED�
PV INSTALLATION
PROFESSIONAL
Scott Gurney
# PV -011719-015866
CONTRACTOR:
BRS FIELD OPS
385.498.6700
City of
/j vvnea '
''Iffbilding Division
Speafieatro are subject to change mthout notikaton SEG -OS -EN -2019)1.1 Copyright 2019 Seraphim
• SHEET NAME
SPEC SHEET
PAGE NUMBER REVISION
SS �
Container 29GP 40'GP
Pieces per Pallet 30 30
WARRANTY
MANAGEMENT SYSTEM
Palkts per Container 12 28
Pieces per Container 360 840
ISO 9001: Quality management system
era a" .,ery� vA�a
ISO 14001: Standard for environmental management system
Mechanical Specifications
��>
OH SAS 18001: International standard for occupational health and safety assessment system
1a.a.sa_.asmm�s+slx3sasa,37�nm,
• a4Y 8r.48X
i,,lll!...I�-I;
6 �`•.=
PRODUCT CERTIFICATES
Meraonaaa�e�� t
3 2m AR mating tempered gtass. lav am
t4 'S 15
CE SEIA1i.o-- t
r�L
AnWizetl a§rmnum Aby
IPfi7
10 Guarantee on product
tl�
C
YEARS material and workmansivp
INSURANCE
MC4 CompMtde
25 Linear output warranty
STC. loadiame 1000 W(m', modde temperature 25'C, AM=1.5
NOCT. Irradiance 800 Whir', ambient temperature 20'C. wind speed 1mis
power
SpedrK:aaons are subject to change without further notification.
YEARS
SpeaSeat,ons are subject to change without nctificato SEC, OS -EN -2019V1.1 Copyright 2019 Seraphim
a 70
I
5.1 21 Section A -A
101
All Dimensions in mm
The above drawing is a graphical representation of the product.
IN Curve
a nc
= sap wm
t
i RAVEN to
1403 N RESEARCH WAY, BUILDING J
OREM, UT 84097
800-377-4480
WWW. BLUERAVENSOLAR.COM
CONFIDENTIAL - THE INFORMATION
HEREIN CONTAINED SHALL NOT BE
USED FOR THE BENEFIT OF
ANYONE EXCEPT BLUE RAVEN
SOLAR NOR SHALL IT BE
DISCLOSED IN WHOLE OR IN PART
TO OTHERS OUTSIDE RECIPIENTS
ORGANIZATION, EXCEPT IN
CONNECTION WITH THE SALE AND
USE OF THE RESPECTIVE
EQUIPMENT, WITHOUT THE
WRITTEN PERMISSION OF BLUE
RAVEN SOLAR LLC.
^.
FCERTIFIED�
PV INSTALLATION
PROFESSIONAL
Scott Gurney
# PV -011719-015866
CONTRACTOR:
BRS FIELD OPS
385.498.6700
City of
/j vvnea '
''Iffbilding Division
Speafieatro are subject to change mthout notikaton SEG -OS -EN -2019)1.1 Copyright 2019 Seraphim
• SHEET NAME
SPEC SHEET
PAGE NUMBER REVISION
SS �
WE
OPTIONAL
FRONT TRIM
I
q)] Will A LA [1111 M
BETTER DESIGNS
TRUST THE INDUSTRY'S BEST DESIGN TOOL
Start the design wocess for every project in inn 11 Builder on-line design tool.
It's a great way to save time and money.
BETTER SYSTEMS
ONE SYSTEM - MANY APPLICATIONS
Quickly set modules flash to the loot oil steep pitched louts. Orient a large variety
of modules in Portrait at Landscape. Tilt the system up on flat at low slow mots.
Components available in milt, clear. and daili: finishes to optimize your design financials
and aesthetics.
It ETTER RESULTS
5
MAXIMIZE PROFITABILITY ON EVERY JOB
Trust lJobae to help you minimize both system and labor costs from the time the job is
quoted to the time your teams get off the root, faster installs. Less Wastc,, Mw Profits.
OUNIW BETTER SUPPORT
WORK WITH THE INDUSTRIES MOST EXPERIENCED TEAM
25 Professional support for rurifeswrial installers and designeis. You have access to
our technical support and training groups. Whatuvei your support needs. we've got
YFARyou covered. Visit Ulli lac,c matsola (luau (it for more ilafollflatioa.
BEST INSTALLATION EXPERIENCE* CURB APPEAL* COMPLETE SOLUTION 9 UNIRACSUPPORT
- BONDING&GROUN01%
MUNGAI, 10AAW
9-01 UL2703 SYSTEMTIRECLASWI
MION
0 so
NOWOUNIRAC
CONCEALED UNIVERSAL
ENOCLAMPS
UNIVERSAL SELF
STANDING MIDCLAMPS
END CAPS INCLUDED
WITH EVERY ENDCLAMP
U -BUILDER ONLINE DESIGN
TOOL SAVES TIME & MONEY
Visit design-urblac-cona
I � � +��� 1111 �
U N"M III U,H DESIGN
It ifi^
uuwly TOOLS DOGUMENTAliON
TECHNICAL SUPPORT CERTIFIED QUALITY PROVIDER BANKABLE WARRANTY
Uninu; s techaaaf support four is dedicated to answering Ifinna; is tfit,, ofilli IN anawfing vendor with fSOcedifications omit leave your padecl to dance, Unix has the Wallow
tjoestions & addressing issues in real time. An online for WPOOR. 14001:2004 and 011W, 18001:2001, streogth to back out products and (educe your insk. Have
library of documents including engineering reports, viduch means we deliver the Ingfiest SlAxils tot fit, pealte of mind knowing you are toovaling products of
statupof letters and technical data sheets greatly fourt, and furaboo. Ifieso codifications demonstrate our excefifionto quality. SOLARMOUNf is Gaveled by a 25 year
simplifies your permitting and project planning process. excellm and commitment to first pass business practices. limited farodul mmulty and a 5 year limited finish warranty.
71UfFrKrr11. itw TAM
City of Wheat Ridge
Residential Electric PERMIT - 201901654
PERMIT NO: 201901654 ISSUED: 08/12/2019
JOB ADDRESS: 8 Hillside Dr EXPIRES: 08/11/2020
JOB DESCRIPTION: Service change - 200 amps; overhead
*** CONTACTS ***
OWNER (303)263-5561 LOUIS A PANEK TRUST
SUB (720)799-8012 PHILLIP EASTWOOD 160081 TIPPING HAT PLMBG, HTG & ELEC
*** PARCEL INFO ***
ZONE CODE: UA / Unassigned USE: UA / Unassigned
SUBDIVISION CODE: 2404 / APPLEWOOD KNOLLS, PARAMOUNT HE BLOCK/LOT#: 0 /
*** FEE SUMMARY *** ESTIMATED PROJECT VALUATION: 8,000.00
FEES
Total Valuation 0.00
Use Tax 168.00
Permit Fee 172.60
** TOTAL ** 340.60
*** COMMENTS ***
*** CONDITIONS ***
Must comply w/ 2012 IRC & 2017 NEC. Subject to field inspection.
I, by my signature, do hereby attest that the work to be performed shall comply with all accompanying approved plans and specifications,
applicable building codes, and all applicable municipal codes, policies and procedures, and that I am the legal owner or have been authorized
by the legal owner of the property and am authorized to obtain this permit and perform the work described and approved in conjunction with
this ermrt. I further attest that I am legally authorized to include all entities named within this document as partes to the work to be
performed and that all work to be performed is disclosed in this document and/or its' accompanying approved plans and specifications.
Signature of OWNER or CONTRACTOR (Circle one) Date
I . This permit was issued based on the information provided in the permit application and accompanying plans and specifications and is
subject to the compliance with those documents, and all applicable statutes, ordinances, regulations, policies and procedures.
2. This permit shall expire 365 days after the date of issuance regardless of activity. Requests for extension must be made in writing and
received prior to the date of expiration. An extension of no more than 180 days made be granted at the discretion of the Chief Building
Official and may be subject to a fee equal to one-half of the originalpermit fee.
3. If this permit expires, a new permit may be required to be obtained. Issuance of a new permit shall be subject to the standard
requirements, fees androcedures for approval of any new permit. Re -issuance or extension of expired permits is at the sole discretion of
the Chief Building Official and is not guaranteed.
4. No work of any manner shall be performed that shall results in a change of the natural flow of water without prior and specific approval.
5. The permit holder shall notify the Building and Inspection Services Division in accordance with established policy of all required
inspections and shall not proceed or conceal work without written approval of such work from the Building and Inspection Services
Division.
6. The issuance or granting of a permit shall not be construed to be a permit for, or an approval of, an violation of any provision of any
applicable code or any ordinance Irpgulation of this jurisdiction. Approval of work is subject to field inspection.
Signature of Chief Building 6fficial Date
REQUESTS MUST BE MADE BY 11:59PM ANY BUSINESS DAY FOR INSPECTION THE FOLLOWING BUSINESS DAY.
�a
Kimber) 4011
Cook
From: no-reply@ci.wheatridge.co.us
Sent: Saturday, August 10, 2019 8:22 PM
To: CommDev Permits
Subject: Online Form Submittal: Residential Electrical Service Change/Upgrade Permit
Application
Residential Electrical Service Change/Upgrade Permit Application
This application is exclusively for RESIDENTIAL ELECTRICAL SERVICE CHANGE
OR UPGRADE (200 amps or less).
YOU MUST ATTACH A VALID CREDIT CARD AUTHORIZATION FORM IN
ORDER FOR THE PERMIT TO BE PROCESSED.
Your Permit will be emailed to the email address provided below once it is
processed.
THIS APPLICATION DOES NOT CONSTITUTE A PERMIT. DO NOT BEGIN
WORK UNTIL PERMIT HAS BEEN ISSUED.
Is this application for Yes
electrical service change
or upgrade - 200 amps or
less?
PROPERTY INFORMATION
Property Address
Property Owner Name
Property Owner Phone
Number (enter WITH
dashes, eg 303-123-4567)
Attach Credit Card
Authorization Form -
**DO NOT ATTACH
RANDOM
DOCUMENTS**
8 Hillside Drive Wheat Ridge, Co 80215
Kae Penner -Howell
303-263-5561
wheat ridge cc auth 1.pdf
CONTRACTOR INFORMATION
Contractor Business
Name
Contractor's License
Number (This is a 5 or 6
Tipping Hat Plumbing, Heating and Electric
160081
1
digit number for the City
of Wheat Ridge)
Contractor Phone 720-799-8010
Number (enter WITH
dashes, eg 303-123-4567)
Contractor Email Address erin@tippinghat.com
Retype Contractor Email erin@tippinghat.com
Address
DESCRIPTION OF WORK
Is this an electrical Change
service upgrade or
change?
Number of Amps 200
Location of house
upgrade/change (garage,
house, etc)
Provide additional details, overhead
if needed.
Project Value (contract 8000
value or cost of ALL
materials and labor)
SIGNATURE OF UNDERSTANDING AND AGREEMENT
I assume full Yes
responsibility for
compliance with
applicable City of Wheat
Ridge codes and
ordinances for work
under any permit
issued based on this
application.
I understand that work Yes
may not begin on this
property until a permit
has been issued and
posted on the property.
I certify that I have been Yes
authorized by the legal
i
owner of the property to
submit this application
and to perform the work
described above.
I attest that everything Yes
stated in this application
is true and correct and
that falsifying
information in this
application is an act of
fraud and may be
punishable by fine,
imprisonment, or both.
Person Applying for Erin Eastwood
Permit
Email not displaying correctly? View it in your browser.
INSPECTION RECORD OCCupancylType
INSPECTION LINE: (303) 234 -5933
Inspections will not be made unless this card is posted on the building site
Call by 3:00 PM to receive inspection the following business day.
Electrical.'
Plumbing
'INSPECTOR MUST SIGN ALL SPACES PERTAINING TO THIS JOB
FOUNDATION INSPECTIONS
DATE -
INSPECTOR
INITIALS
COMMENTS:
Footings /Caissons
- -
Stemwall / (CEG) Concrete
Encased Ground
Building Final
Reinforcing or Monolithic
Fire Department '
Weatherproof/ French Drain
R.O.W & Drainage
Sewer Service Lines
-
-
Water Service Lines
r V V R IY V V V IVt.RC 1 C V IY I IL /16V V C IIMJ OLLIY JIUIYLU
CONCRETE SLAB FLOOR
Electrical (Underground)
Plumbing (Underground)
Heating (Underground)
DON OT POUR FLOOR UNTIL ABOVE HAS BEEN SIGNED.
ROUGHS
Sheathi
ng
Lath /Wall Mid -Roof Electrical RoughEle - "
Rough Plumbing
Gas Piping
Rough Mechanical
a
ABOVE INSPECTIONS TO BE SIGNED PRIOR TO PROCEEDING
Framing _
Insulation
Drywall Screw
I
r�
1"
fa.
ri
FINALS
Electrical.'
Plumbing
Mechanical
Roof
Building Final
'I
Fire Department '
R.O.W & Drainage
INSPECTIONS FOR PLANNING & ZONING, FIRE AND PUBLICE WORKS
SHOULD BE CALLED AT LEAST ONE WEEK PRIOR TO FINAL INSPECTIONS.
Parking & Landscaping
"'NOTE: ALL ITEMS MUST BE COMPLETED AND APPROVED BY PLANNING AND ZONING, BUILDING AND PUBLIC WORKS BEFORE A
CERTIFICATE OF OCCUPANCY IS ISSUED. FINAL INSPECTION BY THE BUILDING DIVISION DOES NOT CONSTITUTE AUTHORIZATION
OF A CERTIFICATE OF OCCUPANCY NOR PERMISSION FOR OCCUPANCY.
' OCCUPANCY NOT PERMITTED UNTIL CERTIFICATE OF OCCUPANCY IS ISSUED '
N
r
" PROTECT THIS CARD FROM THE WEATHER
City of Wheat Ridge Building Division
Date: ~ft 1C>;✓zC~O9('
7500 W. 29th Ave., Wheat Ridge, CO 80033 @
Office: 303-235-2855 * Fax: 303-235-2857 Plan
~O~oeno° Inspection Line: 303-234-5933 permit#:D9,/ ~r967
+ Building Permit Application
Property Address: HdlJsik, Dy- tti)~'42 f ~J a-, CA &32 1 J
n c~~3
Property Owner (please print): L614 S Porte k Phone: ~ j 2-33 1 Ll p d
Mailing Address: (if different than property address)
Address:
City, State, Zip
Contractor: Q r00.10~. ~y7 YMR f1 ~`~AS gY S
u _
Contractor License OW 1 Z5 Phone: Y`J )
Sub Contractors:
Electrical City License Plumbing City License Mechanical City License C~
Company: Company Company:
Exp. Date: Exp. Date: Exp. Date:
Approval: Approval: Approval:
Use of space (description): S~ftz<~yye+ yepoar Construction Value: $ U
Description of work: (as calculated per the Building Valuation Data sheet)
Plan Review due at time of submittal : $
F,,,OY r>Qa zr•r g4v'q.~. -
Sq. Ft./LFt added: Squares BTU's Gallons Amps
OWNERICONTRACTOR SIGNATURE OF UNDERSTANDING AND AGREEMENT
I hereby certify that the setback distances proposed by this permit application are accurate, and do not violate applicable ordinances,
rules or regulations of the City of Wheat Ridge or covenants, easements or restrictions of record; that all measurements shown, and
allegations made are accurate; that I have read and agree to abide by all conditions printed on this application and that I assume full
responsibility for compliance with the Wheat Ridge Building Code (I.B.C) and all other applicable Wheat Ridge Ordinances, for work
under this permit. Plans subject to field inspection.
CIRLCE ONE:: (OWNER) (CONTRALTO or PERSONAL REPRESENTATIVE of (OWNER) (CONTRATOR) 1 p
PRINT NAME:f
SIGNATURE: f\-,~1r~-- tL,t~ Date:
DEPARTMENT USE ONLY
ZONING COMMENTS
Zoning.
Reviewer
PUBLIC WORKS COMMENTS:
Reviewer
BUILDING DEPARTMENT COMMENTS OCCUPANCY:
evieweIU~ECd~"nY"€tk~~[i'Pf-~~CPa7c!'ruGY'V✓ err 1~1nW
FIRE DEP RTM aoo ve w/ co m d' orov o review reauired Bldg Valuation: $
O
3
[D N
z
Q r
- Q
z
O
O ~
N ~
N
0 Q O
~ ~ d 3
Z N N
O N
=:E Co
M0 N = c
J(DQ =b1
N
00AQ
Q p a 3
C)
0
s
0
S
m
b
n
0
3
4
V
I
w
O
0
O 3
N R
O
m
3
b
n ~ m
(D 3.
~Q
3
N
Ul
V
ZION 3
ss
F I~
Q
v
t
w" C
3
a
r
a
m
2
o!
<I
m
n
I
n I
A I
D
m
r
a
r
N
~
m
A
m N
O
zm
M
m
D
D
O
m
m
O
m
D
J
x
0
m
z
m
0
A
D
A
0
z
w
Z
O
x
Z
m
c
m
A
3
y
z
W
C31
W O O
OD N~
cn
Z y
r~
v1
~y
O
ti
A° W N o°° N j° N 0 6 0 i v S 0 C D O C
^ 6
a'
3
°
g
'
w
~
x
0 =FHn
o n3d
n"3Oa m~ooo
_ o_
°
n m
m Q w
o m
s o
Fm
a
e'o
?w
~
3 nos
µ
>
^o
°O
-
.
~
.
.
m~~>
_-wo
Q3
E; ,Z R
O S° F F. c ri 3 4 w 9!
3
°
3
m
wm
Cp°
~
3ym°~of
me T
3~
o
S
o
o=ooo~
x
A~w
w
~
m
5:0 c~v '
s
-
m.a w2
°
"
w
.
- F
a m 3
m
nF
~
m w '
w
J✓
m
~a
x
(A M
w W W xo \ x
U yy
p o Cf)
a0cn-P~ m mA z
(D O. 3
z mDm U) O
tmj 9 VC z
0 u, n ~o
OTC ~ m s co 0 A Tq fA
p,$ X10 OM 0--4 (0 m V/ -n
w U~j
o a m
o~ c *F 0 W a0
o C
PI)
F~ (DD O
m ~
m ](D CN CD Q W ~Oe H5n sg«.xf r Ha ngv3 ow v vmoy33o~~
=nm norm F,°<~-° coo °O o~'O °
mA~om w mym o~ » ~m
-o a _30 0
mm~Sm°av_ ooO om '^oop' o
m.E4 a ~~o Hn mA a
V dy,~. ~n ''og ~ --m ° 6o-e °B u°~ =NO N93 0°~ °m
w
J H ° o o ° ^30 ' o
0
to
1
I
`I•
~ CITY OF WHEAT RIDGE ,
Building Inspection Division
(303) 234-5933 Inspection line
(303) 235-2855 Office ' (303) 235-2857 Fax
INSPECTION( NOTICE
Inspection Type:)
f
Job Address/Permit Number: lf, l1<,;e r d. / ~f4
1 77,
p
1'\),/t'
r ,
t ,
F
a
e
a
❑ No one available for inspection: Time r' AM M
Re-Inspection required: Yes
1670)
When corrections have been made, call for re-inspection at 303-234-5933
Dater (7- u-(A Inspector: lp
ra
DO NOT REMOVE THIS NOTICE
a
` I , '
CITY OF WHEAT RIDGE
� Building Inspection Division
.00 (303) 234 -5933 Inspection line
(303) 235 -2855 Office ' (303) 235 -2857 Fax
INSPECTION NOTICE
Inspection Type: heir
Job Address /Permit Number:
r
❑ No one available for inspection: Time fr :0 AMlPM
Re- Inspection required: "Yes "pNo
When corrections have been made, call for re- inspection at 303 - 234 -5933
Date: Inspector: n '
DO NOT REMOVE THIS NOTICE
A 4' City of Wheat Ridge
roooor- Residential Roofing PERMIT - 091473
PERMIT NO: 091473 ISSUED: 08/19/2009
JOB ADDRESS: 8 HILLSIDE. DR EXPIRES: 02/15/2010
DESCRIPTION: Reroof 25 sqs.
CONTACTS
owner 303/233-.1489 Chris Panek
sub' 303/426-7370.Kurk Tiley 02-1395Tiley Roofing Inc.
PARCEL INFO
ZONE CODE : : UA USE UA
SUBDIVISION: 0678 `BLOCK/LOT#: 0/
**FEE SUMMARY** ESTIMATED. PROJECT VALUATION: 7,651.00
FEES
Permit Fee - 199.30
Total Valuation .00~`-'-.«.%r4
Use Tax 137.72.~r~~li'~(r }
TOTAL 337.02 ~c. ~t gg
Conditions: -
6nail installation &mid-roof inspection required. Board sheathing spaced more
than al/2ofan inch apart requires plywood overlay on entire roof. Ice and
water shield required.. from eaveedge to 2' inside exterior walls.
Subject to field inspections.
I hereby certify that the setback distances proposed by this permit application are accurate, and do not violate applicable
ordinances, rules or regulations of the City of Wheat Ridge or covenants, easements or restrictions of record; that all..
measurements shown, and allegations made are. accurate; that I have read and agree to abide by all conditions printed on this
appli tion and that I assume full responsibility for compliance with the Wheat Ridge Building Code .(I.B.C)and all other
" app ca e i Ordinances, for work under this permit. Plans subject to field inspection.
gnatur co tractor/o r 'date
1. This permit was issue in accordance with the provisions set forth in your application and is subject to the laws of the
State of Colorado and to. the zoning Regulations and Building Codes of 'Wheat Ridge, Colorado or any. other applicable
ordinances of the. city.
2. This permit shall expire 180. days from the issue date. Requests for an extension must be received prior to expiration
'date. An extension may be granted at the discretion of the Building Official.
3. If this permit expires, a new permit may be acquired for a fee of one-half the amount normally required, provided no
changes have been or will be made in the original plans and. specifications and any suspension: or abandonment has not
exceeded one (1) year. If changes have been or if suspension: or abandonment exceeds one (1). year, full fees shall
be paid for a new permit.
4. No work of any manner shall be done that will change the natural flow of water causing a drainage problem.
5. Contractor shall notify the Building. Inspector twenty-four (24) hours in advance for all inspections and shall receive
written approval on inspection card before proceeding. with successive phases of the job.
6. The issuance of a permit or the approval of drawings and specifications shall not be construed to. be a permit for, nor
an approval of,. any violation of the provisions of the. building codes or any other ordinance, law, rule or regulation.
All plan review is subject to field inspections.
n IV
Signature o Building Official `date
INSPECN EQUEST LINE: (303)234-5933 BUILDING OFFICE: (303)235-2855
REQUES S MUST BE MADE BY 3PM ANY BUSINESS DAY FOR INSPECTION THE FOLLOWING BUSINESS DAY.
OFWHEgT~i City of Wheat Ridge Building Division
"m 7500 W. 29th Ave., Wheat Ridge, CO 80033
Office: 303-235-2855 * Fax: 303-235-2857
C~~ORP ° ° Inspection Line: 303-234-5933
Property Address:
Property Owner (pies
Mailing Address: (if different than property address)
Address:
City, State, ;
Contractor:
Date: 41(}~ I OT
Plan A l
Pennit#: 6q vlg6
Contractor License Phone: Z-/"7 -Y7n
Sub' Contractors:
Electrical City License Plumbing City License Mechanical City License
Company: Company Company:
Exp. Date: Exp. Date: Exp. Date:
Approval: Approval: Approval:
Use of space (description): Construction value: $ 362
Description ofworkf~~~~r~~l (as calculated per the Building Valua"on Datasheet)
I Plan Review (due at time of submittal):
Sq. Ft./L.Ftadded: Squares0~J BTU's Gallons Amps
OWNERICONTRACTOR SIGNATURE OF UNDERSTANDING AND AGREEMENT
I hereby certify that the setback distances proposed by this permit application are accurate, and do not violate applicable ordinances,
rules or regulations of the City of Wheat Ridge or covenants, easements or restrictions of record; that all measurements shown, and
allegations made are accurate; that 1 have read and agree to abide by all conditions printed on this application and that I assume full
responsibility for compliance with the Wheat Ridge Building Code (I.B.C) and all other applicable Wheat Ridge Ordinances, for work
under this permit. Plans subject to field inspection.
CIRLCE ON(OWWNEp ~p(C'OONTRACTOR) or PERSOKALj; Ep ) (CO RATOR)
PRINT NAI VE: J; ( A+l~ SIGN \\A77\\UU$$ (.r /
,I
nnm .IPrf
Building Permit Application
4 ♦ ♦ CITY OF WHEAT RIDGE
r Building Inspection Division
1 (303) 234-5933 Inspection line
(303) 235-2855 Office • (303) 235-2857 Fax
a
INSPECTION NOTICEf
Inspection Type: f:5-, M f' q n 1 t. / e
Job Address:
Permit Number: F_-~ f
~,'l ter '
;Y"i
❑ No one available for inspection: Time AM/PM
Re-Inspection required: Yes
When corrections have been made, call for re-inspection at 303-234-5933
Date: f 7 Inspector:
0 NOT REMOVE THIS NOTICE
c,.
♦ i CITY OF WHEAT RIDGE
Building Inspection Division
I (303) 234-5933 Inspection line
(303) 235-2855 Office • (303) 235-2857 Fax
INSPECTION NOTICE
Inspection Type: f&d og✓JtJ Z
Job Address: 7 €t:1!S ip a~
Permit Number: 6 v
~ial✓ ~ /e ~rJ g r yaf£Q
41R
~-t1~~FG~£ ~2 Os7JSdb~
r ❑ No one available for inspection: Time 3 AM/PM
Re-Inspection required: Yjg~> No
When corrections have been made, calf for re-inspection at 303-234-5933
Date: 1 Inspector: A:~a
k, DO NOT REMOVE THIS NOTICE
' City of Wheat
Ridge
k.
f Residential Mechanic
PERMIT - 090367
PERMIT NO: 090367
ISSUED: 04/20/2009
y;
JOB ADDRESS: :8 HILLSIDE DR
EXPIRES: 10./17/2009
DESCRIPTION: Install new boiler leave
exist
ing piping
~L
CONTACTS
owner. 303/233-1489 Louis Panek
sub 303/424-1622 Jack E. Major
Jr.
01-7013 Major Heatina
PARCEL INFO
ZONE CODE: UA
USE: UA
SUBDIVISION: 0678
BLOCK/LOT#: 0/.,
FEE SUMMARY
ESTIMATED
PROJECT VALUATION:: 5,000.00
L
- FEES
Permit Fee.
144.70
. Total Valuation
.00
E
TOTAL
144.70
Conditions:
Subject to field inspections.
k"under `.th
a City of Wheat Ridge Building Division
7500 W. 29th Ave., Wheat Ridge, CO 80033
Office: 303-235-2855 * Fax: 303-235-2857
Inspection Line: 303-234-5933
Date:
N
Plan
Permit #:(001 M, Gl
Building Permit Application
Property Address: ,to
j//~-
Property Owner (please print):
:~;5
Phone:3cs- Z33 /TB9
Mailing Address: (if different than property address)
Address: C
City, State, Zip:
w
Contractor./
izf7
~
Contractor License 7O~
3
Phone:
Sub Contractors:
Electrical City License
Plumbing City L
icense
Mechanical City License
Company:
Company
Company:
Exp. Date:
Exp. Date:
Exp. Date:
Approval:
Approval:
Approval:
Use of space (description):
Construction Value: $
Description of work:
- ~~}!(7!!
~
/ (
,L
d/G° Zr`P
(as calculated per the Building Valuation Data sheet)
ittal
: $
f
b
vi
d
t ti
-
ew
Plan Re
)
me o
su
m
(
ue a
64$, Vey,
Sq. Ft./L.Ft added: Squares
BTU's
Gallons
Amps
OWNER/CONTRACTOR SIGNATURE OF UNDERSTANDING AND AGREEMENT
I hereby certify that the setback distances proposed by this permit application are accurate, and do not violate applicable ordinances,
rules or regulations of the City of Wheat Ridge or covenants, easements or restrictions of record: that all measurements shown, and
allegations made are accurate: that I have read and agree to abide by all conditions printed on this application and that I assume full
responsibility for compliance with the Wheat Ridge Building Code (I.B.C) and all other applicable Wheat Ridge Ordinances, for work
under this permit. Plans subject to field inspection.
CIRLCE ONE:: ,-(-OWNER) (CONTRACTOR) or RPR7NTATIVE of NEV CONTRATOR)
PRINT NAME: _ \ Pi uu SIGNAT E- Date:.. zr.b
DEPARTMENT USE ONLY
ZONING COMMENTS:
Zoning: -
Reviewer:'
PUBLIC WORKS COMMENTS:
Reviewer:
BUILDING DEPARTMENT COMMENTS OCCUPANCY:.
Reviewer: -
FIRE DEPARTMENT:: ❑ approved w/ comments ❑ disapproved no review required Bldg Valuation: $